Powerwave Technologies LNKA100 LINKNET RF BROADBAND AMPLIFIER MODULE User Manual LinkNet VHF Broad V1 1003

Powerwave Technologies Inc. LINKNET RF BROADBAND AMPLIFIER MODULE LinkNet VHF Broad V1 1003

Contents

BROCHURE

Download: Powerwave Technologies LNKA100 LINKNET RF BROADBAND AMPLIFIER MODULE User Manual LinkNet VHF Broad V1 1003
Mirror Download [FCC.gov]Powerwave Technologies LNKA100 LINKNET RF BROADBAND AMPLIFIER MODULE User Manual LinkNet VHF Broad V1 1003
Document ID381735
Application IDBc9aUClKEtTGXOEA91RCNg==
Document DescriptionBROCHURE
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize7.92kB (99027 bits)
Date Submitted2003-12-16 00:00:00
Date Available2003-12-16 00:00:00
Creation Date2003-10-14 14:35:56
Producing SoftwareAcrobat Distiller 5.0 (Windows)
Document Lastmod2003-10-27 15:21:03
Document TitleLinkNet_VHF_Broad_V1-1003.qxd
Document CreatorADOBEPS4.DRV Version 4.50
Document Author: gmistry

TM
LinkNet
Service Module
LNKA100
Servicing VHF. Broadband Version.
Kaval’s advanced LinkNet VHF Service Module is a digitally controlled Class-A amplifier designed to operate within
the LinkNet Convergence Platform to extend coverage of the vhf (136-174 MHz) spectrum range.
Software configured, this broadband amplifier’s main function is to receive, amplify and transmit its designated
frequency range and to ensure that clean, clear signals arrive at their intended destination.
Because of LinkNet’s modular design, additional service modules can be added to keep pace with technological
advancements or changes in user demand, making LinkNet the most flexible, scalable, and cost-effective solution
on the market today.
Features & Benefits
Installation & Service Features All LinkNet Service Modules are
‘plug-and-play/unplug-and-remove’ to minimize installation
down time and eliminate the need for extensive service
equipment on site.
Diagnostic Features Each LinkNet Service Module automatically
performs a self-diagnostic check when inserted into the chassis.
As well, all major fault conditions are constantly monitored,
including:
Primary power failure
Thermal management
Hot Swappable Features LinkNet Service Modules can be added
or replaced within the LinkNet Convergence Platform without
powering down the system. This provides quick and easy
maintenance with no disruption to service.
Over-current/under-current
TM
Trademark of Kaval Wireless Technologies.
SM
Service Mark of Kaval Wireless Technologies.
SM
1.888.86.kaval www.kaval.com
Wireless inside. Made possible.
TM
LinkNet
Service Module
LNKA100
Specifications
Product Deployment
Signals are received via an off air donor antenna located on
the exterior of the building, from a nearby macro cell site.*
The LinkNet Convergence platform converges and amplifies
signals which are then distributed to each floor via coaxial
cable. Kaval’s patented Tap-In signal taps and a series of
ceiling mounted antennas provide balanced coverage
throughout the building.
Module Specifications
Donor Antenna
LinkNet™ Convergence Platform
Frequency Range
LNKA100-A 136-155 MHz, LNKA100-B 150-174 MHz
Modulation and Bandwidth
Broadband Amplifier
RF Gain Adjustment Range
+34 dB to +84 dB, in 1 dB increments
AGC Control Adjustment Range
+15 dBm to +30 dBm
3rd Order Intercept Point IP3
+47 dBm Typical
Noise Figure
<8 dB, 5 dB Typical
Transmit Duty Cycle
Continuous
Transmit Spurious
-13 dBm Maximum
Receive Conducted Spurious
-57 dBm Maximum
Power Module Supply Requirements
40 Watts Maximum
Group Delay
<5 µs
RF Connectors
SMA (50 Ω) Connectors on back of Chassis
Connections
DB-15 Connector on back of Chassis provides Per-Module Fault Relay,
Interconnect to other Modules, and RS-232 connection.
Front Panel Indicators
Operating, Stand By, Fault, Program Mode, Receive, Transmit
Configuration Options
Modules may be configured via optional Gateway Module, or via PC and a RS-232 Connection
Mechanical Characteristics
Dimensions (W x H x D)
2" x 9.11" x 14"
Weight
10 lbs. approx.
Operating Temperature Range*
-100C to +500C
Operating Humidity Range
10 to 90% RH, Non-Condensing
Coaxial Cable
Tap-In™ and Ceiling Antenna
* Consult Kaval for installation specific forced-air cooling requirements.
ab
Specifications are subject to change without notice.
* Signals may be taken directly from base
station via fiber or T1 connection if so desired.
V1-10/03
SM
1.888.86.kaval www.kaval.com
Wireless inside. Made possible.

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Page Count                      : 2
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:bf726e67-f85f-479b-abb5-99a3e09c0b00
Producer                        : Acrobat Distiller 5.0 (Windows)
Create Date                     : 2003:10:14 14:35:56Z
Modify Date                     : 2003:10:27 15:21:03-08:00
Metadata Date                   : 2003:10:27 15:21:03-08:00
Creator Tool                    : ADOBEPS4.DRV Version 4.50
Document ID                     : uuid:99f977fc-7912-4b4b-9bad-6ce0f08c5f23
Format                          : application/pdf
Creator                         : gmistry
Title                           : LinkNet_VHF_Broad_V1-1003.qxd
Author                          : gmistry
EXIF Metadata provided by EXIF.tools
FCC ID Filing: H6M-LNKA100

Navigation menu