Precise Biometrics MS010120 Fingerprint Reader User Manual Installation

Download:
Mirror Download [FCC.gov]
Document ID	587132
Application ID	G7LX0fD6o+fWeM6JcGo5sA==
Document Description	Users Manual Installation
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	90.74kB (1134255 bits)
Date Submitted	2005-09-29 00:00:00
Date Available	2005-09-29 00:00:00
Creation Date	2005-09-02 15:40:19
Producing Software	Acrobat Distiller 6.0.1 (Windows)
Document Lastmod	2005-09-26 16:20:55
Document Title	Microsoft Word - Installation of Precise BioAccess_2.doc
Document Creator	PScript5.dll Version 5.2.2
Document Author:	maline

Installation of
Precise BioAccess™ 200
Sweden Precise Biometrics AB, Scheelevägen 19 C, SE-223 70 Lund
Phone +46 46 31 11 00
Fax +46 46 31 11 01
info@precisebiometrics.com
nd
Precise Biometrics AB, Finlandsgatan 66 2 floor, SE-164 74 Kista
Phone +46 8 632 33 50
Fax +46 8 632 33 55
info@precisebiometrics.com
USA
Precise Biometrics Inc, 8300 Boone Boulevard, Suite 500, Vienna VA 22182
Phone +1 (703) 848 9266
Fax +1 (703) 832 0577
infous@precisebiometrics.com
UK
Precise Biometrics Ltd, 288 Bishopsgate, London EC2M 4QP
Phone +44 (0) 207 959 3060 Fax +44 (0) 207 959 3030 info@precisebiometrics.com
www.precisebiometrics.com
1.
Connect the wires using a shielded cable. The shielding must be
connected to earth at the access control side of the system.
BioAccess plint 1
BioAccess plint 2
1 Do not connect
2 DATA (magstripe) / DATA 0
(Wiegand) OUTPUT
3 CLOCK (magstripe) / DATA 1
(Wiegand) OUTPUT
4 CARD PRESENT OUTPUT
5 RS485 B
6 RS485 A
7 ground
8 Extra ground
9 Extra ground
10 POWER 12-24 VDC
1 Do not connect
2 Do not connect
3 Do not connect
4 Do not connect
5 RS232 Out
6 RS232 In
7 Do not connect
8 Do not connect
9 Do not connect
10 Do not connect
2.
Fasten the holder onto the wall. Recommended mounting
height 1.4meter/4.6 feet.
3.
Plint 1
Plint 2
Plug the connector(s). Plint 1 should be connected to the left
and plint 2 should be connected to the right.
4.
If the BioAccess reader is going to be connected to an
Ethernet, connect the RJ-45 contact.
5.
Mount Precise BioAccess™ 200 onto the holder.
6.
Secure Precise BioAccess™ 200. Use only screw driver Torx
T10. Torque max 1.0 Nm.
CE Notice (Europe)
This device meets the following technical standards as indicated by the
symbol on the device:
•
•
•
•
•
•
EN
EN
EN
EN
EN
EN
55022:1998 Limit B (Radiated emission)
55024:1998 (Immunity of IT-equipment)
61000-6-2:1999 (Immunity for industrial environments)
300 330-2: v.1.1.1 (06-2001) (Radio - spectrum)
301 489-01: v.1.2.1 (07-2000) (Radio - EMC)
301 489-03 (07-2000) (Radio - EMC)
FCC Information (USA)
This device has been certified to the FCC rules and regulations (CFR47
Part 15 Subpart C) for the low power transmitter contained within this
device. In addition, this device has also been verified to comply with Class
B digital device requirements as specified in the FCC rules and
regulations (CFR47 Part 15 Subpart B).
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver
is connected
• Connect the equipment into an outlet on a circuit different from that to
which the receiver
• Consult the dealer or an experienced radio/TV technician for help
CAUTION: Changes or modifications not expressly approved by the party

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 6
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:6e6e5847-2b46-4c8e-a76f-83ca8dbbd3ca
Producer                        : Acrobat Distiller 6.0.1 (Windows)
Creator Tool                    : PScript5.dll Version 5.2.2
Modify Date                     : 2005:09:26 16:20:55+02:00
Create Date                     : 2005:09:02 15:40:19+02:00
Metadata Date                   : 2005:09:26 16:20:55+02:00
Document ID                     : uuid:a17c2505-4e0c-40a1-bcf7-060e5bbdac93
Format                          : application/pdf
Title                           : Microsoft Word - Installation of Precise BioAccess_2.doc
Creator                         : maline
Author                          : maline

EXIF Metadata provided by EXIF.tools