Primax Electronics B80402 Bluetooth Headset User Manual PHS 3 USER GUIDE

Download:
Mirror Download [FCC.gov]
Document ID	578740
Application ID	fEx0fwTRzlT1MibK3C2GTg==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	40.46kB (505769 bits)
Date Submitted	2005-09-07 00:00:00
Date Available	2005-09-06 00:00:00
Creation Date	2005-08-04 16:43:27
Producing Software	Acrobat PDFWriter 5.0Windows NT ª©
Document Lastmod	2005-08-30 16:20:37
Document Title	PHS-3 USER GUIDE.cdr
Document Creator	CorelDRAW 9 - [PHS-3 USER GUIDE] (預覽列印)
Document Author:	Administrator

Introduction
Thanks for purchasing Primax PHS-3. Your Primax PHS-3 is a stylish
headset that enables comfortable handsfree communication with
compatible phone that supports Bluetooth technology.
The Primax PHS-3 contains the following parts, As shown in Figure 1.
5. Charger connector For battery charging.
6. Earpiece Relays the caller's voice.
7. Earhook Attaches headset to ear.
Figure 1
. Answer incoming call
. End active call
. Reject incoming call by long pressing button
. Switching ongoing call and waiting call by long pressing the
1.Power/Send/End key
Switches the headset on and off
button when call is in progress
2.Indicator Light
Power on
Blue light flashes for 5 times and beep once.
. Pairing state
Blue/red light flashing alternatively, the flashing
continues for approximately 10 minutes or until the headset is
connected to a compatible phone. If the headset can't be
connected to the phone during this time, the headset is
switched off.
. Connectable
3. Volume up Increases the earpiece volume during a call.
4. Volume down Decreases the earpiece volume during a call.
. Connection active Blue light flashing every 3 seconds.
. Call end Beep once.
. Power off Red light flashing for 5 times and beep once.
. Low battery Red light flashing every 5 seconds.
Blue light flashing every 5 seconds.
Pairing the Bluetooth headset to a
Bluetooth mobile phone
Pairing is the process of linking the headset with your Bluetooth
enabled mobile phone. After this process is completed, you can use
the Primax PHS-3 only with this paired mobile phone. If you want to
use Primax PHS-3 with another mobile phone, you must repeat the
pairing process again. The Primax PHS-3 can be paired with up to 8
compatible phones but connected to only one phone at a time.
1. Make sure that the compatible phone is turned on and within
10 meter of the headset.
2.Turn on Primax PHS-3 and make sure the headset is charged. Press
and hold volume up key and volume down key together for 3 seconds.
The Blue and red LEDs will flash alternatively. Release both buttons
and the headset is now in pairing mode.
8. Microphone Picks up your voice input.
3. Activate the Bluetooth connection from the phone. You may need to
consult with mobile phone user guide of your phone regarding how to
do that.
Getting started
4. Set the phone to start searching for Bluetooth devices as instructed
in user guide of your phone.
Package Content
. PHS-3 Headset
. Charger
. User guide
Charging the battery
Before using Primax PHS-3, you must charge the product for
approximately 2 hours. When the battery is fully charged, it provides
up to 9 hours of talk time and up to 200 hours of standby time.
1. Connect the charger cable to Primax PHS-3 as shown
in the Figure 1.
2. Plug the AC adapter into a wall outlet. When Primax PHS-3 is
charging, red indicator light will display.
3. When the battery is fully charged, the blue indicator light is displayed.
Unplug the charger cable from the wall outlet and Primax PHS-3.
5. Select the Primax PHS-3 from the list.
6. Enter the pin code 0000 to connect (or "pair") Primax PHS-3 to the
phone.
Primax PHS-3 beeps once and an active Bluetooth connection is
displayed by a blinking blue indicator light.
If Primax PHS-3 is turned on within 10 meters of several paired
phones, the headset will try to connect to the last connected phone
within 10 seconds. If the headset cannot connect to the last connected
phone(for example, phone is turned off or it rejects the connection),
it remains connectable for other phones for approximately 10 minutes,
which is displayed by the blinking blue indicator light. If the connection
cannot be made during this time, the headset is turned off automatically.
7. Some phones require additional step to connect the headset under
the Bluetooth menu, please make sure the device connection is
activated.
8. Headset is ready to be used.
Disconnecting the Bluetooth headset
from the phone
To disconnect Primax PHS-3 from the phone, do one of the following:
1 Turn off Primax PHS-3.
2. Disconnect Primax PHS-3 in the phone menu.
Answering and ending a call
When you receive a call, you hear a ringing tone through the headset.
Press the power/send/end key to answer the call or to end the
currently active call.
You can also answer and end the call using the phone.
3. Move the headset more than 10 meters away from the phone.
Rejecting a call
Primax PHS-3 is also disconnected if the battery becomes flat.
When you receive an incoming call that you do not want to answer,
simply press the power/send/end key and hold it for 3 seconds.
Note that you do not need to delete the pairing with the headset to
disconnect it. When you reconnect a paired headset, you will not be
asked for its pin code.
Redialing the last dialed number
Reconnecting the paired Bluetooth
headset to the compatible phone
Muting an ongoing call
To reconnect Primax PHS-3 to the last connected phone, turn on
Primax PHS-3. Otherwise, make the connection in the phone menu
as instructed in the user guide of your phone.
Powering Up
To turn on Primax PHS-3
Press and hold the power key for 3 seconds. Primax PHS-3 beeps and
the blue indicator light starts blinking. The blinking continues for
approximately 10 minutes or until the headset is connected to a
compatible phone. If the headset cannot be connected to the phone
during this time, the headset is turned off.
To turn off Primax PHS-3
Press and hold the power key for 3 second, Primax PHS-3 beeps and
the red indicator light is displayed briefly.
Making calls
When Primax PHS-3 is connected to the phone, make a call by using
the phone in the normal way. Note that the call functions depend on
the phone that you use.
Press the volume up key for 3 seconds when no call is in progress.
You can mute or unmute the ongoing call by pressing the
power/send/end and volume up keys together for 3 seconds when
a call is in progress.
Voice dialing (Phone dependant)
When no call is in progress, press volume down key and hold it for 3
seconds until there is a tone that indicates that you can start saying
the voice tag. The phone plays the voice tag and dials the related
phone number.
Adjusting the earphone volume
Press the volume up key to increase or the volume down key to
decrease the volume.
Switching the call between phone and
headset
Press the power/send/end and volume down keys together for 3
seconds or use the respect function in your phone.
Switching ongoing call and waiting call
When a call is in progress, there is another call is coming in. Simply
press power/send/end key and hold it for more than 5 seconds or use
the respect function in your phone.
Three way conference call
When a call is in progress, three way conference call is activated
by pressing volume down key for 3 seconds.
Federal Communication Commission
Interference Statement
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
FCC Caution: Any changes or modifications not expressly approved by the
party responsible for compliance could void the user's authority to operate this
equipment.
IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. End users must follow the specific operating
instructions for satisfying RF exposure compliance.
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Encryption                      : Standard V1.2 (40-bit)
User Access                     : Print, Fill forms, Extract, Assemble, Print high-res
XMP Toolkit                     : 3.1-701
Create Date                     : 2005:08:04 16:43:27Z
Creator Tool                    : CorelDRAW 9 - [PHS-3 USER GUIDE] (預覽列印)
Modify Date                     : 2005:08:30 16:20:37+08:00
Metadata Date                   : 2005:08:30 16:20:37+08:00
Format                          : application/pdf
Creator                         : Administrator
Title                           : PHS-3 USER GUIDE.cdr
Producer                        : Acrobat PDFWriter 5.0Windows NT ª©
Document ID                     : uuid:b652e17a-f301-464c-9609-b1b1be31b1ff
Instance ID                     : uuid:a7e189d7-db61-4a04-95a5-e7a95ea2eb0f
Has XFA                         : No
Page Count                      : 2
Author                          : Administrator

EXIF Metadata provided by EXIF.tools