Primax Electronics M7B601 PC Card Mouse User Manual NEW 5584 MoGo PR

Primax Electronics Ltd PC Card Mouse NEW 5584 MoGo PR

Manual

Visit our website at: www.mogomouse.comFeatures and specifications are subject to change without notice.2006 Newton Peripherals, LLC MG-100-01-0002-01 rev 2Bluetooth Laptop MouseInstallation GuideUse itlike your wireless desktop mouseStore Itinside a PC card slotCharge itautomatically
Newton Peripherals MoGo MouseBTIntroductionCongratulations on your purchase of a MoGo MouseBT. This user’s guide describes how to connect and use the MoGo MouseBT to your Laptop.In addition to this user’s guide this package contains:• Newton Peripherals MoGo MouseBTSystem RequirementsTo use the MoGo MouseBT, your computer must meet the following requirements:Hardware• Type II PC card slot• USB Bluetooth adaptor or embedded Bluetooth Operating System• Bluetooth®-enabled Windows®98, Me, 2000, or XP. • Bluetooth®-enabled Macintosh®running Mac®OS 10.2.8 or later. Charging and StoringThe MoGo MouseBT is equipped with an internalrechargeable battery. It is recommended thatbefore using, you insert the MoGo MouseBTinside your type II PC card slot for charging.The MoGo MouseBT automatically begins to charge when installed. The laptop mustbe turned on for charging to take place.You should allow up to 60 minutes for initial charging of MoGo MouseBT.Charging status is indicated by either a red light for active charging or a green light for fully charged. GREEN = CHARGEDRED = CHARGINGBattery LED Status
What to do if the “Found new Hardware Wizard” appearsWhen inserting the MoGo MouseBT in your computer’s PCMCIA slot for the first time, the window below may appear. Though no software is required for the MoGo MouseBT to charge properly, Microsoft Windows will try to load a driver for the MoGo MouseBT. To stop Microsoft Windows from displayingthis window follow the steps below. Once completed no other action isrequired for setting up your laptop for charging. You may see a message appear warning you that the driver was not installed and your device my not work properly. You can ignore this as the MoGo MouseBT does not need a driver to operate properly. Pairing your MoGo MouseBT with your laptopBluetooth devices require that you initially “pair” your MoGo MouseBT with your laptop. Follow the stepsbelow to prepare your MoGo MouseBT for pairing.Once paired to your laptop the MoGo MouseBT onlyneeds to be turned on for operation with your laptop.1. Turn on the MoGo MouseBT by opening kickstand onside of unit with finger. You may notice a one time RED blinkfrom Optical Sensor on the bottom of the mouse. 2. Press the “connect” button down until the status light startsflashing blue, every 2 seconds. Your MoGo MouseBT is now readyto pair to your laptop. It will stay in this state for 3 minutes.3. Initiate your laptop Bluetooth to complete pairing your mouse. In case you are requested to enter a Pass Code or PIN number, simply enter “0000”. MoGo MouseBT does not require such a code to operate. Refer to the owner’s manual for specific instructions on pairing your laptop Bluetooth. Check the box to install automatically and click “Next”.Check the box at the bottom (Don’t Prompt me again to install the software) and click finish.
Once connected the blue light on the MoGo MouseBT will begin to blink slowly, every 3 seconds. 4. You are ready to MoGo!Pairing Your MoGo MouseBT with another LaptopYour MoGo MouseBT can only be paired with one laptop at a time. Pressingthe connect button will break the current pairing and prepare the MoGoMouseBT to be paired with another laptop.Using your MoGo MouseBTSince the MoGo MouseBT fits into the Type II PC card slot to store and charge,it needs a kickstand to prop up the back of the mouse to make it functionaland ergonomic. To turn it on, open the kickstand from the side. Click the rightor left button to activate the connection. Note: initially, you must pair theMoGo MouseBT to the laptop before this can occur. Turning the MoGo MouseBT off is simple. Collapse/close the kickstand andMoGo MouseBT will automatically turn off. Leaving the MoGo MouseBT untouched for ten minutes will cause the mouse to fall asleep. Wake it by simply pressing the right or left button. Note: TheMoGo Mouse is designed so that leaving it in sleep mode reduces battery useto save battery power.If the laptop Bluetooth signal becomes unavailable to the mouse, this willalso cause the mouse to fall asleep. If the indicator LED turns solid red, the battery is very low and needs to be recharged. Operating HintsFor optimal performance and RF reception:• Avoid using the MoGo MouseBT on a metal surface. Metals, such as iron, aluminum or copper, shield the Bluetooth transmission and may slow down the MoGo MouseBT’s response time or cause the MoGo MouseBT to fail temporarily. •The MoGo MouseBT will enter a suspend mode at the same time your computer does. To activate the MoGo MouseBT, press any button on your MoGo MouseBT.
•If your computer has a metal case that contains aluminum or magnesium, use the MoGo MouseBT to the side. The display panel may interfere with the Bluetooth signal if you use the MoGo MouseBT directly in front of the computer. •Glass or mirrored surfaces can result in erratic behavior for all mice using optical technology.•To maximize battery life, use the MoGo MouseBT on a white, or light colored surface. Dark surfaces cause the MoGo MouseBT’s light emitting diode (LED) light to glow brighter, which causes the battery to discharge more rapidly.SpecificationsTroubleshootingThe MoGo MouseBT is not working.•Make sure that the MoGo MouseBT is charged. Install into type II PC card slot and wait for Green LED indicator.• Verify that Bluetooth is configured correctly on your computer1) Click Start/Settings/Control Panel/System/Hardware/Device Manager. 2) Check under ‘Bluetooth Devices’ that a ‘Newton Peripherals MoGo MouseBT’is installed. I cannot connect to a paired device.• Paired Bluetooth devices are displayed in a connection management window of your Bluetooth management application, even if the remote device is out of range or not powered up. •Verify that the remote member of the pair is within Bluetooth range, and powered up, and then attempt the connection again. Bluetooth Specification Resolution Working range RF transmit power OperatingBattery Voltage Operating CurrentStandby Current Sleep Mode Current Dimensions Weight1.1 and 1.2 compliant500 DPIUp to 30 feet (10 m)<4 dBm4.2 V165 mAh Internal Rechargeable 32 mA22 mA.04 mA3.4 x 2.125” x .21 inches(86 x 54 x 5 mm)1.5 oz or 41 grams
I cannot discover Bluetooth services on an un-paired remote device.• The remote device may not be powered up or may be out of range.• Verify that the remote device is powered up.• Verify that the remote device is in Connectable mode (Bluetooth Configuration Panel > Accessibility tab).• Perform a Search for Devices to verify that the device is within range.For technical questions, please visit: North America Email: supportna@newtonperipherals.comEMEA Email: supportemea@newtonperipherals.comASIA Email: supportasia@newtonperipherals.comProduct RegistrationNewton Peripherals recommends that you register your Newton Peripherals accessory shortly after purchasing it. To register your Newton Peripherals accessory, go to: http://www.Newtonperipherals.com/registration/ You will need to provide your full name, email address, phone number, date purchase, place of purchase and company information (if applicable). WarrantyNewton Peripherals warrants this product to be free from defects in materials and workmanship for two years from the date of purchase of the Products. The warranty extends only to you if you are the end user with original purchase receipt. We will, at our option, repair or replace the Products that do not conform to the warranty. We may use functionally equivalent reconditioned/ refurbished/remanufactured/pre-owned or new Products or parts. If your Newton Peripherals accessory is found to be defective within that time, we will promptly repair or replace it. This warranty does not cover accidental damage, wear and tear, or consequential or incidental loss. Under no conditions is Newton Peripherals liable for loss of, or damage to a computer; nor loss of, or damage to, programs, records, or data; nor any consequential or incidental damages, even if Newton Peripherals has been informed of their possibility. This warranty does not affect your statutory rights. Regulatory ComplianceThis device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
Ready, set…MoGo!Easy to stow, ready to goIntegrated “kickstand” flips out to position MoGo MouseBT comfortablyPatent-pending optics providesmooth, accurate performanceNo batteries to replace — takes just minutes to recharge inside your laptopBluetooth operation delivers wireless freedom©2006 Newton Peripherals, LLC. All Rights Reserved. Bluetooth is a registered trademark of Bluetooth SIG. All other trademarks and registered trademarks are the property of their respective holders. Patents Pending.

Navigation menu