Pro Tracker TRACKER1 Pro-tracker The Ultimate Tracking Device User Manual Microsoft PowerPoint Module manual 2014 10 31

Download:
Mirror Download [FCC.gov]
Document ID	2436889
Application ID	MkReLwahyr15OzSNf6v1Zw==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	45.82kB (572780 bits)
Date Submitted	2014-11-06 00:00:00
Date Available	2014-11-06 00:00:00
Creation Date	2014-10-31 15:16:36
Producing Software	Acrobat Distiller 9.2.0 (Windows)
Document Lastmod	2014-10-31 15:19:17
Document Title	Microsoft PowerPoint - Module manual 2014 10 31
Document Creator	PScript5.dll Version 5.2.2
Document Author:	Elaine

Tracker 1 User Manual
Module description
Programming port interface description
Down Loading code description
Exclusive Application Platform Description for Module
Transfer protocol
RF General Information
Programming port interface description
Gnd
VCC
CLK
Data
Reset
SPI
Programming
Pins
CC Debugger
Connector
Down Loading code description
Move mouse to upper right corner icon to click it ,
and then Flash Programmer will appear.
Next, move the mouse to Flash programmer
Anti‐white area and click the mouse,
then enter the programming Screen..
Programming screen
C:\Transmit_20140627_2.HEX
Select programming file
1000
Fill in four
Check the box
Fill in 1000
Transmitter ID
97 98 99 9A 9B 9C 9D 9E 9F A0 A1 A2 A3 A4
A5 A6 A7 A8 A9 AA AB AC AD AE AF B0 B1 …
………
Click “Perform actions”
Programming OK
Exclusive Application Platform Description for Module
module only used for Pro‐Tracker platform
V‐
Battery
V+
After installing the battery, move magnet away,
then turn on the power to send out information
move magnet close, turn off the power
• Transfer protocol
• Baud Rates : 2.4K
Start
First 30 minutes 12 seconds on to sending information
6 seconds off
After 30 minutes 10 seconds on to sending information
6 seconds off
After 1 hour
8 seconds on to sending information
6 seconds off
After 1 hours
8 seconds on to sending information
8 seconds off
• RF General Information
•
•
•
•
•
Frequency Range : 902‐928 MHz
Modulation : FSK
Ch. Frequency : 905‐927.25 Mhz
Bandwith : 250 KHz
Channel Number : 89
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could
void the user's authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or
transmitter.
IMPORTANT NOTE:
This module is intended for OEM integrator.
The OEM integrator is still responsible for the FCC compliance requirement of the end product, which integrates this
module.
Appropriate measurements (e.g. 15 B compliance) and if applicable additional equipment authorizations (e.g.
Verification , Doc) of the host device to be addressed by the integrator/manufacturer.
LABEL OF THE END PRODUCT:
The final end product must be labeled in a visible area with the following " Contains TX FCC ID: 2ADB5-TRACKER1 ".

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Author                          : Elaine
Create Date                     : 2014:10:31 15:16:36+08:00
Modify Date                     : 2014:10:31 15:19:17+08:00
XMP Toolkit                     : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04
Format                          : application/pdf
Title                           : Microsoft PowerPoint - Module manual  2014 10 31
Creator                         : Elaine
Creator Tool                    : PScript5.dll Version 5.2.2
Metadata Date                   : 2014:10:31 15:19:17+08:00
Producer                        : Acrobat Distiller 9.2.0 (Windows)
Document ID                     : uuid:abc14eef-2410-4e5a-8d4d-b848af4a677a
Instance ID                     : uuid:ed963697-e292-4ccd-a30f-b4830cbf902d
Page Count                      : 8

EXIF Metadata provided by EXIF.tools