Protectli FW6X Mini Pc User Manual
Protectli Mini Pc
User Manual
Mini Pc User Manual Version 1.0 Published May 2015 Content 1. Introduction........................................................................................................................................ 1 1.1 Specification................................................................................................................................. 2 1.2 Package Contents.................................................................................................................... 3 1.3 I/O Panel………………………………………………………………………………………………….4 2. Installation.......................................................................................................................................... 4 2.1 Screw Holes.................................................................................................................................. 5 2.2 Pre-installation Precautions.................................................................................................. 6 2.3 Installation of Memory Modules...................................................................................... 6 2.4 3D Drawing..................................................................................................................... 6 2.5 Dimension and Interface...........................................................................................6 Chapter 1: Introduction 1.1Specification Model Processor Chipset RAM Display port Expansion port Storage Audio Network FW6A-0 Adopt Intel Celeron 3865U dual core (14nm, 1.8GHz, 2MB second Cache) , core i3-7100U is optional Adopt Intel express chipset 2*SODDR4(can up to 32G) Integrated Intel HD Graphic card, Support 1*HDMI 2*Mini-PCIE, support WiFi 1* MINISATA, 1*2.5” SATA N/A 6* Intel WG82583 1000M Lan, support wake on lan 6* RJ-45 1* 12V DC input I /O Built-in I/O BIOS WDT Power supply Temp Humidity Dimension 1* HDMI 4 *USB3.0 1*Power switch 1*RJ-45 COM 1 * FP1 1 * J2 1 * JSATA Port, 1*SATA 1 * MINI_PCIE for WiFi, 1 * Mini-SATA 1 * SODIMM 1 * CPU_Fan AMI 64M DPI Flash ROM Support hardware reset (256 level,0~255 sec) DC-12V -20℃~60℃ 0~95% relative humidity, non-condensing 155*126*52mm 1.2Package Contents 1.FW6A-0 Main Host 2.Vesa Bracket 3.Screw Package 1.3 I/O Panel Chapter 2 2.1 screw holes Put screws into the holes to secure the motherboard to the chassis . And Put screws into the hole to secure the bottom panel to the chassis . 2.1 Pre-installation precautions Take note of the following precautions before you install motherboard components or change any motherboard settings. 1. Unplug the power cord from the wall socket before touching any component . 2. To avoid damaging the motherboard components due to static electricity, Never place your motherboard directly on the carpet or the like . Also remember to use a grounded wrist strap or touch a safety grounded object before you handle components . 3. Hold components by the edges and do not touch the ICs. 4. Whenever you uninstall any component, place it on a grounded antistatic pad or in the bag that comes with the component . 2.3Installation Memory Modules Please make sure to disconnect power supply before adding or removing So-DIMMs or the system components. Step1. Unlock a SO-DIMM slot by pressing the retaining clips outward. Step2. Align a SO-DIMM on the slot such that the notch on the SO-DIMM matches the break on the slot 2.4 3D Drawing 2.5 Dimension and Interface FCC Caution This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.7 Linearized : No Author : admin Comments : Company : Create Date : 2017:08:16 09:41:37+01:30 Modify Date : 2017:11:22 09:13:54+08:00 Source Modified : D:20170816094137+01'41' Subject : Trapped : false Has XFA : No XMP Toolkit : Adobe XMP Core 5.6-c015 81.157285, 2014/12/12-00:43:15 Format : application/pdf Creator : admin Description : Title : Creator Tool : WPS Office Metadata Date : 2017:11:22 09:13:54+08:00 Keywords : Producer : Document ID : uuid:174ff07d-bb14-40ed-901f-ad32eba9539b Instance ID : uuid:c7cdf7df-4054-462f-9410-c2e020840f2b Page Count : 8EXIF Metadata provided by EXIF.tools