Psion HFAM2G2 RFID READER HF-AM2-G2 User Manual USERS MANUAL

Download:
Mirror Download [FCC.gov]
Document ID	916195
Application ID	lgO9ZezbY1m6JsMFgbi2hQ==
Document Description	USERS MANUAL
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	110.08kB (1376045 bits)
Date Submitted	2008-03-18 00:00:00
Date Available	2008-03-19 00:00:00
Creation Date	2008-02-25 16:28:21
Producing Software	Acrobat Distiller 8.1.0 (Windows)
Document Lastmod	2008-02-25 16:28:21
Document Title	Microsoft Word - RFID Reader HF-AM2-G2 UserMan A00.doc
Document Creator	PScript5.dll Version 5.2.2
Document Author:	heyer

WORKABOUT PRO G2
RFID Reader HF-AM2-G2
User Manual
Title
RFID reader HF-AM2-G2 User Manual
Doc Type
User Manual
Doc Id
TS A00350
Revision
Date
Name
Status/Comment
A00
12/12/07
F.DEBULOIS
Initial Version
Specifications are subject to change without notice
Psion Teklogix™ is a trademark of Psion Teklogix Inc. Other product names mentioned
in this document may be trademarks of Psion Teklogix Inc. or trademarks or registered
trademarks of other hardware, software, or service providers and are used herein for
identification purposes only.
RFID Reader HF-AM2-G2 – User Manual
TS-A00350-A00
Page 2/19
Table of Content
I. Important – read carefully............................................................................................. 4
II. Overview ..................................................................................................................... 4
II.1. Bill of Material ................................................................................................................. 4
II.2. Interface Board installation .............................................................................................. 5
II.3. Reader Board Installation ................................................................................................. 6
II.3.1. HF-AM2-G2 Endcap ...............................................................................................................6
II.3.2. SAGEM endcap dual reader with slot......................................................................................6
III. Hardware installation ................................................................................................. 7
III.1. Preparing ......................................................................................................................... 7
III.2. Interface Board installation ............................................................................................. 8
III.3. Reader Board installation................................................................................................ 8
III.3.1. HF-AM2-G2 Endcap assembly ..............................................................................................8
III.3.2. SAGEM endcap dual reader with slot assembly...................................................................10
III.4. Endcap connection ........................................................................................................ 14
III.4.1. HF-AM2-G2 Endcap ............................................................................................................14
III.4.2. SAGEM endcap dual reader with slot ..................................................................................15
III.5. Final steps ..................................................................................................................... 15
IV. Reading Area............................................................................................................ 16
V. RFID Regulatory Information ................................................................................... 16
RFID Reader HF-AM2-G2 – User Manual
TS-A00350-A00
Page 3/19
I. Important – read carefully
All Approval and safety information is outlined in the ‘Workabout pro G2 Handheld-computer User
Manual’ – part number 8100140A. This manual is available on our website
www.psionteklogix.com through the Teknet extranet
II. Overview
II.1. Bill of Material
RFID Reader HF-AM2-G2 is composed of :
- an interface board, connected in the Workabout Pro G2 Handheld computer
- a reader board, with its built-in antenna
- a flex cable, which connects the two boards.
Flex cable
Reader Board
Interface
Board
RFID Reader HF-AM2-G2 – User Manual
TS-A00350-A00
Page 4/19
II.2. Interface Board installation
The interface Board has to be installed in the Workabout Pro:
Specific end
cap
Flex cable to
reader board
Interface
Board
Built-in scanner
flex cable
RFID Reader HF-AM2-G2 – User Manual
TS-A00350-A00
Page 5/19
II.3. Reader Board Installation
The reader board has to be installed in a specific endcap depending of the configuration:
II.3.1. HF-AM2-G2 Endcap
II.3.2. SAGEM endcap dual reader with slot
RFID Reader HF-AM2-G2 – User Manual
TS-A00350-A00
Page 6/19
III. Hardware installation
III.1. Preparing
Before installing a module in the WORKABOUT PRO G2, all power sources must be
turned off.
Remove the batteries. If your unit is using
AC power, disconnect it.
Remove the End cap at the top of the
WORKABOUT PRO G2
RFID Reader HF-AM2-G2 – User Manual
TS-A00350-A00
Slide the switch to position OFF to shut off internal
battery power
Remove the backplate
Page 7/19
III.2. Interface Board installation
Plug the flex cable as shown
Insert the bard as shown and screw the 4
provided screws
III.3. Reader Board installation
The reader board intends to fit in a specific endcap which depends on the desired configuration.
Each following paragraph describes how to assemble every configuration.
III.3.1. HF-AM2-G2 Endcap assembly
Here are the required parts
Insert the reader board in the rubber
RFID Reader HF-AM2-G2 – User Manual
TS-A00350-A00
A multipurpose endcap
A rubber
A sticker
Inject silicon on the 3 internal sides of the
endcap
Page 8/19
Place the rubber inside the endcap…
and press strongly
Put silicon between the rubber and the reader
board ….
in order to ensure a good holding
Stick the sticker on the top of the endcap
RFID Reader HF-AM2-G2 – User Manual
TS-A00350-A00
Page 9/19
III.3.2. SAGEM endcap dual reader with slot assembly
The following drawing shows the whole assembly
Here are the required parts
RFID Reader HF-AM2-G2 – User Manual
TS-A00350-A00
1 MSO sensor
1 Top moulding
1 MSO plate
1 biometric endcap
1 8-ways MSO cable
4 self tapping screws
4 thorx screws
4 washers
1 smart card board
3 gaskets
1 rubber
1 reader board
Page 10/19
The first step is to build the fingerprint unit (top- subassembly)
Here are the required parts
1 MSO sensor
1 Top moulding
1 MSO plate
1 8-ways MSO cable
4 self tapping screws
4 washers
2 gaskets
Prepare the gasket and the MSO sensor
Place the gasket on the sensor as shown
Place the sensor in the top moulding
Check the gasket positioning
RFID Reader HF-AM2-G2 – User Manual
TS-A00350-A00
Page 11/19
Connect the MSO cable to the MSO sensor
Prepare the MSO plate and its gasket
Put the gasket on the plate as shown
Place the cover on the top moulding
Screw the 4 self tappings screws with their
washer
Put silicon in the MSO cable window to ensure
proper sealing
RFID Reader HF-AM2-G2 – User Manual
TS-A00350-A00
Page 12/19
It is now time to perform final assembly:
Insert the reader board in the rubber
Insert the assembly in the endcap slot
Stick the gasket around the smart card board
connector
Place the smart card board on the top of the
endcap
The smart card board and the reader board are
plugged together with a 8-ways SIL connector
Pass the 8 way connector of the fingerprint unit
through the window of the endcap
RFID Reader HF-AM2-G2 – User Manual
TS-A00350-A00
Page 13/19
Close the endcap with the fingerprint unit and
screw the 4 thorx screws
Finish the endcap sealing with a silicon
injection in the 8-way cable window.
III.4. Endcap connection
The endcap has to be connected to the interface board:
III.4.1. HF-AM2-G2 Endcap
Connect the flex cable from the interface board to
the reader board.
RFID Reader HF-AM2-G2 – User Manual
TS-A00350-A00
Screw then endcap
Page 14/19
III.4.2. SAGEM endcap dual reader with slot
Connect the flex cable from the interface board to
the reader board. And the MSO cable in the
dedicated connector
Screw then endcap
III.5. Final steps
Slide the switch located in the battery casing to
position ON
RFID Reader HF-AM2-G2 – User Manual
TS-A00350-A00
Put back the batteries and close the
battery cover.
Page 15/19
IV. Reading Area
This area depend of the TAG type, TAG packaging, configuration of the WORKABOUT
PRO (scanner, Compact flash…), environment (metallic or not).
V. RFID Regulatory Information
RFID Reader HF-AM2-G2 – User Manual
TS-A00350-A00
Page 16/19
RFID Reader HF-AM2-G2 – User Manual
TS-A00350-A00
Page 17/19
RFID Reader HF-AM2-G2 – User Manual
TS-A00350-A00
Page 18/19
IMPORTANT NOTE FOR NORTH AMERICA:
The RFID must not be used whilst the host WORKABOUT PRO is being powered by the ac/dc
adaptor.
FCC Information to Users:
This product and it antennas must not be co-located or operated in conjunction with any other
antenna or transmitter.
Radiation Exposure Compliance
This product complies with the FCC RF exposure limits for an uncontrolled environment. For
continued compliance, the product must not be held closer than 20 cm from the rest of the body.
Federal Communication Commission Interference Statement.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a
particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one of the following measures:
•
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment.
Emissions Information for Canada:
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
RFID Reader HF-AM2-G2 – User Manual
TS-A00350-A00
Page 19/19

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
XMP Toolkit                     : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39
Creator Tool                    : PScript5.dll Version 5.2.2
Modify Date                     : 2008:02:25 16:28:21+01:00
Create Date                     : 2008:02:25 16:28:21+01:00
Format                          : application/pdf
Title                           : Microsoft Word - RFID Reader HF-AM2-G2 UserMan A00.doc
Creator                         : heyer
Producer                        : Acrobat Distiller 8.1.0 (Windows)
Document ID                     : uuid:5afe4925-64ce-4d4a-b8fa-d1e6dc5390b6
Instance ID                     : uuid:5219ae30-2a0f-4d50-a1d4-1b3dd8540696
Page Count                      : 19
Author                          : heyer

EXIF Metadata provided by EXIF.tools