Psion HFT2A1 RFID Module HF-T2-A1 User Manual User Guide

Download:
Mirror Download [FCC.gov]
Document ID	536352
Application ID	u/GTOzHQqpVHpUfXZoywVg==
Document Description	User Guide
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	48.5kB (606251 bits)
Date Submitted	2005-04-27 00:00:00
Date Available	2005-04-27 00:00:00
Creation Date	2005-04-08 17:41:44
Producing Software	Acrobat Distiller 5.0.5 (Windows)
Document Lastmod	2005-04-08 17:41:44
Document Title	Microsoft Word - Expansion module instruction DPD A00063 A20.doc
Document Creator	PScript5.dll Version 5.2.2
Document Author:	pporte

WORKABOUT PRO RFID MODULE HF-T2-A1 EXPANSION MODULE INSTRUCTIONS
Important: All Approval and safety information is outlined in the ‘Workabout pro
Handheld-computer User Manual’ – part number 8000024. This manual is available on
our website www.psionteklogix.com through the Teknet extranet
Easily installable expansion modules for the WORKABOUT PRO allow you to customise this hand-held to
meet your specific mobile computing requirements. This chapter outlines how to install the RFID Module
HF-T2-A1 (this module is composed of one RFID Coupler HF-T2 and one RFID Antenna HF-A1).
Before installing a module in the WORKABOUT PRO, all power sources must be turned off.
•
Remove the batteries. If your unit is using AC power, disconnect it.
•
Remove the End cap at the top and the back plate of the WORKABOUT PRO.
•
Slide the SW1401 switch to the left to shut off internal battery power.
With the power shut down, you can install the RFID Module HF-T2-A1.
•
Remove and discard the two screws on the bottom of the metal frame.
•
Put the RFID Coupler HF-T2 in the same alignment of the expansion connector on the
WORKABOUT PRO. Apply slight pressure to snap the module into place on the hand-held.
•
Use four new screws (M2 x 6 mm) provided to secure the module in place.
DPD A00063 A20
April 8, 2005
Sheet 1 of 4
•
Remove and discard the two screws on the top of the metal frame.
•
Slide the RFID Antenna HF-A1 under the metal frame (with the spiral pattern facing up).
•
Connect the RFID Antenna HF-A1 to the RFID Coupler HF-T2.
•
Use two new screws (M2 x 12mm) provided to secure the antenna on the metal frame.
•
Slide the SW1401 switch to the right to turn power back on.
•
Replace the end-cap, back plate and batteries.
For detailed instructions, pleased refer to the WORKABOUT PRO Hand-Held Computer User Manual and
to the RFID MODULE HF-T2-A1 User manual. These manuals are available on our website
www.psionteklogix.com through the Teknet extranet
DPD A00063 A20
April 8, 2005
Sheet 2 of 4
WORKABOUT PRO RFID MODULE HF-T2-A1 RFID Regulatory Information
DPD A00063 A20
April 8, 2005
Sheet 3 of 4
IMPORTANT NOTE FOR NORTH AMERICA:
The RFID must not be used whilst the host WORKABOUT PRO is being powered by the ac/dc adaptor.
FCC Information to Users:
This product and it antennas must not be co-located or operated in conjunction with any other antenna or
transmitter.
Radiation Exposure Compliance
This product complies with the FCC RF exposure limits for an uncontrolled environment. For continued
compliance, the product must not be held closer than 20 cm from the rest of the body.
Federal Communication Commission Interference Statement.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used
in accordance with the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following
measures:
•
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate this equipment.
Emissions Information for Canada:
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
DPD A00063 A20
April 8, 2005
Sheet 4 of 4

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Create Date                     : 2005:04:08 17:41:44+02:00
Modify Date                     : 2005:04:08 17:41:44+02:00
Page Count                      : 4
Creation Date                   : 2005:04:08 15:41:44Z
Mod Date                        : 2005:04:08 15:41:44Z
Producer                        : Acrobat Distiller 5.0.5 (Windows)
Author                          : pporte
Metadata Date                   : 2005:04:08 15:41:44Z
Creator                         : pporte
Title                           : Microsoft Word - Expansion module instruction DPD A00063 A20.doc

EXIF Metadata provided by EXIF.tools