Psion RA80211G 802.11b/g Wireless LAN CF Card User Manual User Guide Module rev 1

Psion Inc 802.11b/g Wireless LAN CF Card User Guide Module rev 1

User manual rev

802.11b/g Wireless LAN CF cardRA2040-G1User Guide Version 2.0 Jan.23, 2006
- 1 - A. Specifications Host Interfaces Compact FlashCompatible Interfaces Compact Flash Type ǿForm factor Compact Flash Type ǿChipset MARVELL 88W8385 + 88W8015 Operation Voltage DC 3.3V Network Standards IEEE 802.11g/bModulation Techniques DBPSK, DQPSK, CCK, 16QAM, 64QAM, Modulation Technology DSSS and OFDM Data Rate 802.11b: 11, 5.5, 2, 1 Mbps 802.11g: 54, 48, 36, 24, 18, 12, 9, 6 Mbps Network Architectures Infrastructure and Ad HocOperating Frequencies 2.4 – 2.4835 GHzOperating Channels 802.11b/g: 1-11 for North AmericaRF Output PowerBefore antenna 802.11b (1M,2M,5.5M,11M) : 13 dBm802.11g (6M,9M,12M,18M,24M,36M, 48M,54M) : 13 dBm Receiver sensitivity 802.11b:1M=-90dBm,2M=-90dBm,5.5M=-90dBm,11M=-87dBm 802-11g:6M=-83dBm,9M=-83dBm,12M=-83dBm,18M=-83dBm,24M=-81dBm 36M=-78dBm,48M=-74dBm,54M=-73dBm Power Consumption Tx peak: 500mA @ 3.3VDC; Rx peak: 275mA @ 3.3VDCSupport Voltage 3.3VSecurityz WEP 64-and 128-bit encryption with hardware TKIP processing. z WPA Delay Tolerance Multi-path R.M.S Delay Spread @ 10%FER 680 ns in 11M mode,150ns in 54M modeSoftware Support Windows CE 4.2 & CE 5.0,.LinuxTemperaturesOperates from -20 to 70 кStorage from -40 to 120 кHumidity (non-condensing) 5 to 95%*CertificationsWi-Fi Pretest*; FCC part 15C/15.247*; ETS 300 328-2*; UL*; IEC60950*; EN 301 489-1,17*; prEN50371*;CE Mark*; TELEC**Perform approved procedure is based on customer’s request. WLFWireWireless CF Card_RA2040-G1 Design Specification Rev.6
- 2 - B. Marvell WLAN 802.11b/g CF8385PN Software Feature Short preamble802.11b, 802.11g, and g/b mix-mode infrastructure802.11b and 802.11g Adhoc modeTransmit fragmentation and receive defragmentationClient IEEE Power Save Infrastructure & Adhoc modeBasic rate adaptation - 11g/b for optimizing each STA throughputCore Features Background scan64/ 128-bit WEP Encryption and open/ shared authentication WPA PSK WPA 802.1x WPAII PSK** WPAII 802.1x** Cisco CCX V1 (LEAP)** Hardware AES Security AH Security IEEE 802.11b IEEE 802.11g IEEE 802.11d** IEEE 802.11e (EDCA)** IEEE StandardsIEEE 802.11e (HCCA)** Wi-Fi WME** Other Standards Wi-Fi WSM APSD** Drivers for the following Operating SystemsWindows CE.net (CE4.2, CE5.0) Windows Pocket PC 2003 Windows Mobile Edition Linux 2.4.22 and aboveNetwork Protocol TCP/IP, IPX** NOTE **The transmitter module is authorized for use in specific End-product (WORKABOUT PROHand-held Micro-computer as models of 7525C, 7525M-E and 7525S).
- 3 - C. Block Diagram***Subject to be changed without notice.
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. IMPORTANT NOTE: FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This device is intended only for Psion Teklogix Inc’s 7525C, 7525M-E and 7525S Series PDA or Psion Teklogix Inc’s platforms with substantially similar physical dimensions, construction, and electrical and RF characteristics under the following conditions: 1) The transmitter module may not be co-located with any other transmitter except Bluetooth device FCC ID: GM37525BTB which has been certified with this product. 2) Product can be sold only to end-user who already has the Psion Teklogix Inc’s products, or be used in Psion Teklogix’s product lines as mentioned above. The product shall not be marketed at public retail stores. Psion Teklogix Inc is responsible for testing their end-product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, etc.). IMPORTANT NOTE: Please notice that this product is only for Psion’s 7525C, 7525M-E and 7525S Series PDA or Psion’s platforms with substantially similar physical dimensions, construction, and electrical and RF characteristics. The usage of this product in other application may cause violation to US/Canada EMC or RF exposure rules and is prohibited. End Product Labeling The final end product must be labelled in a visible area with the following: “Contains TX FCC ID: GM3RA80211G”. Manual Information That Must be Included in End-Product End-users must be provided with specific information required to satisfy RF exposure compliance for the final host device. The transmitter module must not be co-located or operated in conjunction with any other transmitter or antenna not described in application filings under this FCC ID: GM3RA80211G. As long as the conditions mentioned above are met, further transmitter tests will not be required. However, the grantee shall bear the responsibility for compliance of the device in all final host configurations.
IMPORTANT NOTE: If the conditions mentioned above cannot be met, then the FCC authorization is no longer considered valid and the FCC ID cannot be used on the final product. Under the circumstances, the grantee will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization.

Navigation menu