18290 2 Franklin Electric Submersible Motor User Guide M1311_60_Hz_AIM_Catalog Manual
18184 2 Franklin Electric Submersible Motor Control User Guide 18184_2_Franklin Electric Submersible Motor Control User Guide 18184_2_Franklin Electric Submersible Motor Control User Guide pdf pumpproducts
User Manual: Pump 18290 2 Franklin Electric Submersible Motor User Guide
Open the PDF directly: View PDF 
.
Page Count: 80
| Download | |
| Open PDF In Browser | View PDF |
SUBMERSIBLE MOTORS
!PPLICATION s )NSTALLATION s -AINTENANCE
FRANKLIN ELECTRIC
2011 AIM MANUAL
(Z 3INGLE 0HASE AND 4HREE 0HASE -OTORS
ATTENTION!
IMPORTANT INFORMATION FOR INSTALLERS OF THIS EQUIPMENT!
THIS EQUIPMENT IS INTENDED FOR INSTALLATION BY TECHNICALLY QUALIFIED PERSONNEL.
FAILURE TO INSTALL IT IN COMPLIANCE WITH NATIONAL AND LOCAL ELECTRICAL CODES, AND
WITHIN FRANKLIN ELECTRIC RECOMMENDATIONS, MAY RESULT IN ELECTRICAL SHOCK OR FIRE
HAZARD, UNSATISFACTORY PERFORMANCE, AND EQUIPMENT FAILURE. FRANKLIN INSTALLATION
INFORMATION IS AVAILABLE FROM PUMP MANUFACTURERS AND DISTRIBUTORS, AND DIRECTLY
FROM FRANKLIN ELECTRIC. CALL FRANKLIN TOLL FREE 800-348-2420 FOR INFORMATION.
WARNING
SERIOUS OR FATAL ELECTRICAL SHOCK MAY RESULT FROM FAILURE TO CONNECT THE MOTOR,
CONTROL ENCLOSURES, METAL PLUMBING, AND ALL OTHER METAL NEAR THE MOTOR OR CABLE,
TO THE POWER SUPPLY GROUND TERMINAL USING WIRE NO SMALLER THAN MOTOR CABLE
WIRES. TO REDUCE RISK OF ELECTRICAL SHOCK, DISCONNECT POWER BEFORE WORKING ON OR
AROUND THE WATER SYSTEM. DO NOT USE MOTOR IN SWIMMING AREAS.
ATTENTION!
INFORMATIONS IMPORTANTES POUR L’INSTALLATEUR DE CET EQUIPEMENT.
CET EQUIPEMENT DOIT ETRE INTALLE PAR UN TECHNICIEN QUALIFIE. SI L’INSTALLATION N’EST
PAS CONFORME AUX LOIS NATIONALES OU LOCALES AINSI QU’AUX RECOMMANDATIONS DE
FRANKLIN ELECTRIC, UN CHOC ELECTRIQUE, LE FEU, UNE PERFORMANCE NON ACCEPTABLE,
VOIRE MEME LE NON-FONCTIONNEMENT PEUVENT SURVENIR. UN GUIDE D’INSTALLATION
DE FRANKLIN ELECTRIC EST DISPONIBLE CHEZ LES MANUFACTURIERS DE POMPES, LES
DISTRIBUTEURS, OU DIRECTEMENT CHEZ FRANKLIN. POUR DE PLUS AMPLES RENSEIGNEMENTS,
APPELEZ SANS FRAIS LE 800-348-2420.
AVERTISSEMENT
UN CHOC ELECTRIQUE SERIEUX OU MEME MORTEL EST POSSIBLE, SI L’ON NEGLIGE DE
CONNECTER LE MOTEUR, LA PLOMBERIE METALLIQUE, BOITES DE CONTROLE ET TOUT METAL
PROCHE DU MOTEUR A UN CABLE ALLANT VERS UNE ALIMENTATION D’ENERGIE AVEC BORNE
DE MISE A LA TERRE UTILISANT AU MOINS LE MEME CALIBRE QUE LES FILS DU MOTEUR. POUR
REDUIRE LE RISQUE DE CHOC ELECTRIQUE. COUPER LE COURANT AVANT DE TRAVAILLER PRES
OU SUR LE SYSTEM D’EAU. NE PAS UTILISER CE MOTEUR DANS UNE ZONE DE BAIGNADE.
ATENCION!
INFORMACION PARA EL INSTALADOR DE ESTE EQUIPO.
PARA LA INSTALACION DE ESTE EQUIPO, SE REQUIERE DE PERSONAL TECNICO CALIFICADO.
EL NO CUMPLIR CON LAS NORMAS ELECTRICAS NACIONALES Y LOCALES, ASI COMO CON LAS
RECOMENDACIONES DE FRANKLIN ELECTRIC DURANTE SU INSTALACION, PUEDE OCASIONAR,
UN CHOQUE ELECTRICO, PELIGRO DE UN INCENDIO, OPERACION DEFECTUOSA E INCLUSO LA
DESCOMPOSTURA DEL EQUIPO. LOS MANUALES DE INSTALACION Y PUESTA EN MARCHA DE
LOS EQUIPOS, ESTAN DISPONIBLES CON LOS DISTRIBUIDORES, FABRICANTES DE BOMBAS
O DIRECTAMENTE CON FRANKLIN ELECTRIC. PUEDE LLAMAR GRATUITAMENTE PARA MAYOR
INFORMACION AL TELEFONO 800-348-2420.
ADVERTENCIA
PUEDE OCURRIR UN CHOQUE ELECTRICO, SERIO O FATAL DEBIDO A UNA ERRONEA CONECCION
DEL MOTOR, DE LOS TABLEROS ELECTRICOS, DE LA TUBERIA, DE CUALQUIER OTRA PARTE
METALICA QUE ESTA CERCA DEL MOTOR O POR NO UTILIZAR UN CABLE PARA TIERRA DE CALIBRE
IGUAL O MAYOR AL DE LA ALIMENTACION. PARA REDUCIR EL RIESGO DE CHOQUE ELECTRIC,
DESCONECTAR LA ALIMENTACION ELECTRICA ANTES DE INICIAR A TRABAJAR EN EL SISTEMA
HIDRAULICO. NO UTILIZAR ESTE MOTOR EN ALBERCAS O AREAS EN DONDE SE PRACTIQUE
NATACION.
Commitment to Quality
Franklin Electric is committed to provide customers with
defect free products through our program of continuous
improvement. Quality shall, in every case, take
precedence over quantity.
35"-%23)",% -/4/23
(Z 3INGLE 0HASE AND 4HREE 0HASE
!PPLICATION s )NSTALLATION s -AINTENANCE -ANUAL
The submersible motor is a reliable, efficient and troublefree means of powering a pump. Its needs for a long
operational life are simple. They are:
1. A suitable operating environment
2. An adequate supply of electricity
3. An adequate flow of cooling water over the motor
4. An appropriate pump load
All considerations of application, installation, and
maintenance of submersible motors relating to these four
areas are presented in this manual. Franklin Electric’s
web page, www.franklin-electric.com, should be checked
for the latest updates.
Contents
Application
!LL -OTORS
Storage ................................................................................ 3
Frequency of Starts ............................................................. 3
Mounting Position ................................................................ 3
Transformer Capacity ........................................................... 4
Effects of Torque .................................................................. 4
Use of Engine Driven Generators ........................................ 5
Use of Check Valves ............................................................ 5
Well Diameters, Casing, Top Feeding, Screens ................... 6
Water Temperature and Flow ............................................... 6
Flow Inducer Sleeve ............................................................ 6
Head Loss Past Motor ......................................................... 7
Hot Water Applications ..................................................... 7-8
Drawdown Seals .................................................................. 9
Grounding Control Boxes and Panels .................................. 9
Grounding Surge Arrestors .................................................. 9
Control Box and Panel Environment .................................... 9
Equipment Grounding .......................................................... 9
3INGLE 0HASE -OTORS
3-Wire Control Boxes ......................................................... 10
2-Wire Motor Solid State Controls ..................................... 10
QD Relays (Solid State) ..................................................... 10
Cable Selection 2-Wire or 3-Wire ...................................... 11
Two Different Cable Sizes .................................................. 12
Single-Phase Motor Specifications .................................... 13
Single-Phase Motor Fuse Sizing ....................................... 14
Auxiliary Running Capacitors............................................. 15
Buck-Boost Transformers ................................................... 15
4HREE 0HASE -OTORS
Cable Selection - 60 °C Three-Wire.............................. 16-17
Cable Selection - 60 °C Six-Wire ....................................... 18
Cable Selection - 75 °C Three-Wire.............................. 19-20
Cable Selection - 75 °C Six-Wire ....................................... 21
Three-Phase Motor Specifications................................ 22-28
Overload Protection ...................................................... 29-31
Submersible Pump Installation Checklist (No. 3656)
Submersible Motor Installation Record (No. 2207)
Submersible Booster Installation Record (No. 3655)
SubMonitor ........................................................................ 32
Power Factor Correction .................................................... 32
Three-Phase Starter Diagrams .......................................... 33
Three-Phase Power Unbalance ......................................... 34
Rotation and Current Unbalance ....................................... 34
Three-Phase Motor Lead Identification.............................. 35
Phase Converters .............................................................. 35
Reduced Voltage Starters .................................................. 36
Inline Booster Pump Systems....................................... 36-39
Variable Speed Operation ............................................. 40-41
)NSTALLATION
!LL -OTORS
Submersible Motors - Dimensions ..................................... 42
Tightening Lead Connector Jam Nut ................................. 43
Pump to Motor Coupling .................................................... 43
Pump to Motor Assembly ................................................... 43
Shaft Height and Free End Play ........................................ 43
Submersible Leads and Cables ......................................... 43
-AINTENANCE
!LL -OTORS
System Troubleshooting ................................................ 44-45
Preliminary Tests................................................................ 46
Insulation Resistance......................................................... 47
Resistance of Drop Cable .................................................. 47
3INGLE 0HASE -OTORS AND #ONTROLS
Identification of Cables ...................................................... 48
Single-Phase Control Boxes .............................................. 48
Ohmmeter Tests................................................................. 49
QD Control Box Parts ........................................................ 50
Integral hp Control Box Parts ........................................ 51-52
Control Box Wiring Diagrams ........................................ 53-57
%LECTRONIC 0RODUCTS
Pumptec-Plus Troubleshooting During Installation ............ 58
Pumptec-Plus Troubleshooting After Installation ............... 59
QD Pumptec and Pumptec Troubleshooting ...................... 60
SubDrive/MonoDrive Troubleshooting........................... 61-62
SubMonitor Troubleshooting .............................................. 63
Subtrol-Plus Troubleshooting ........................................ 64-65
!00,)#!4)/.
!LL -OTORS
3TORAGE
Franklin Electric submersible motors are a waterlubricated design. The fill solution consists of a mixture
of deionized water and Propylene Glycol (a non-toxic
antifreeze). The solution will prevent damage from
freezing in temperatures to -40 °F (-40 °C); motors should
be stored in areas that do not go below this temperature.
The solution will partially freeze below 27 °F (-3 °C),
but no damage occurs. Repeated freezing and thawing
should be avoided to prevent possible loss of fill solution.
There may be an interchange of fill solution with well
water during operation. Care must be taken with motors
removed from wells during freezing conditions to
prevent damage.
When the storage temperature does not exceed
100 °F (37 °C), storage time should be limited to two
years. Where temperatures reach 100° to 130 °F, storage
time should be limited to one year.
Loss of a few drops of liquid will not damage the motor
as an excess amount is provided, and the filter check
valve will allow lost liquid to be replaced by filtered well
water upon installation. If there is reason to believe there
has been a considerable amount of leakage, consult the
factory for checking procedures.
&REQUENCY OF 3TARTS
The average number of starts per day over a period
of months or years influences the life of a submersible
pumping system. Excessive cycling affects the life of
control components such as pressure switches, starters,
relays and capacitors. Rapid cycling can also cause
motor spline damage, bearing damage, and motor
overheating. All these conditions can lead to reduced
motor life.
The pump size, tank size and other controls should be
selected to keep the starts per day as low as practical for
longest life. The maximum number of starts per 24-hour
period is shown in table 3.
Motors should run a minimum of one minute to dissipate
heat build up from starting current. Six inch and larger
motors should have a minimum of 15 minutes between
starts or starting attempts.
Table 3 Number of Starts
MOTOR RATING
MAXIMUM STARTS PER 24 HR PERIOD
HP
KW
SINGLE-PHASE
THREE-PHASE
Up to 0.75
Up to 0.55
300
300
1 thru 5.5
0.75 thru 4
100
300
7.5 thru 30
5.5 thru 22
50
100*
40 and over
30 and over
-
100
* Keeping starts per day within the recommended numbers
provides the best system life. However, when used with
a properly configured Reduced Voltage Starter (RVS) or
Variable Frequency Drive (VFD), 7.5 thru 30 hp three-phase
motors can be started up to 200 times per 24 hour period.
-OUNTING 0OSITION
Franklin submersible motors are designed primarily for
operation in the vertical, shaft-up position.
During acceleration, the pump thrust increases as its
output head increases. In cases where the pump head
stays below its normal operating range during startup and
full speed condition, the pump may create upward thrust.
This creates upward thrust on the motor upthrust bearing.
This is an acceptable operation for short periods at each
start, but running continuously with upthrust will cause
excessive wear on the upthrust bearing.
With certain additional restrictions as listed in this section
and the Inline Booster Pump Systems sections of this
manual, motors are also suitable for operation in positions
3
from shaft-up to shaft-horizontal. As the mounting position
becomes further from vertical and closer to horizontal, the
probability of shortened thrust bearing life increases. For
normal motor life expectancy with motor positions other
than shaft-up, follow these recommendations:
1. Minimize the frequency of starts, preferably to
fewer than 10 per 24-hour period. Six and eight
inch motors should have a minimum of 20 minutes
between starts or starting attempts
2. Do not use in systems which can run even for short
periods at full speed without thrust toward the motor.
!00,)#!4)/.
!LL -OTORS
4RANSFORMER #APACITY
3INGLE 0HASE OR 4HREE 0HASE
Distribution transformers must be adequately sized to
satisfy the kVA requirements of the submersible motor.
When transformers are too small to supply the load, there
is a reduction in voltage to the motor.
Table 4 references the motor horsepower rating, singlephase and three-phase, total effective kVA required, and
the smallest transformer required for open or closed
three-phase systems. Open systems require larger
transformers since only two transformers are used.
Other loads would add directly to the kVA sizing
requirements of the transformer bank.
Table 4 Transformer Capacity
MOTOR RATING
HP
SMALLEST KVA RATING-EACH TRANSFORMER
TOTAL
EFFECTIVE
KVA
REQUIRED
KW
OPEN WYE
OR DELTA
2- TRANSFORMERS
CLOSED
WYE OR DELTA
3- TRANSFORMERS
1.5
1.1
3
2
1
2
1.5
4
2
1.5
3
2.2
5
3
2
5
3.7
7.5
5
3
7.5
5.5
10
7.5
5
10
7.5
15
10
5
7.5
15
11
20
15
20
15
25
15
10
25
18.5
30
20
10
30
22
40
25
15
40
30
50
30
20
50
37
60
35
20
60
45
75
40
25
75
55
90
50
30
100
75
120
65
40
125
93
150
85
50
175
100
60
150
110
175
130
200
115
70
200
150
230
130
75
NOTE: Standard kVA
ratings are shown. If power
company experience and
practice allows transformer
loading higher than
standard, higher loading
values may be used to
meet total effective kVA
required, provided correct
voltage and balance is
maintained.
%FFECTS OF 4ORQUE
During starting of a submersible pump, the torque
developed by the motor must be supported through the
pump, delivery pipe or other supports. Most pumps rotate
in the direction which causes unscrewing torque on
right-handed threaded pipe or pump stages. All threaded
joints, pumps and other parts of the pump support system
must be capable of withstanding the maximum torque
repeatedly without loosening or breaking. Unscrewing
joints will break electrical cable and may cause loss of the
pump-motor unit.
To safely withstand maximum unscrewing torques with
a minimum safety factor of 1.5, tightening all threaded
joints to at least 10 lb-ft per motor horsepower is
recommended (table 4A). It may be necessary to tack
or strap weld pipe joints on high horsepower pumps,
especially at shallower settings.
Table 4A Torque Required (Examples)
MOTOR RATING
HP
KW
MINIMUM SAFE
TORQUE-LOAD
1 hp & Less
0.75 kW & Less
10 lb-ft
20 hp
15 kW
200 lb-ft
75 hp
55 kW
750 lb-ft
200 hp
150 kW
2000 lb-ft
4
!00,)#!4)/.
!LL -OTORS
5SE OF %NGINE $RIVEN 'ENERATORS
3INGLE 0HASE OR 4HREE 0HASE
Table 5 lists minimum generator sizes based on typical
80 °C rise continuous duty generators, with 35%
maximum voltage dip during starting, for Franklin’s threewire motors, single- or three-phase.
This is a general chart. The generator manufacturer
should be consulted whenever possible, especially on
larger sizes.
There are two types of generators available: externally
and internally regulated. Most are externally regulated.
They use an external voltage regulator that senses the
output voltage. As the voltage dips at motor start-up, the
regulator increases the output voltage of the generator.
Internally regulated (self-excited) generators have an
extra winding in the generator stator. The extra winding
senses the output current to automatically adjust the
output voltage.
Generators must be sized to deliver at least 65% of the
rated voltage during starting to ensure adequate starting
torque. Besides sizing, generator frequency is important
as the motor speed varies with the frequency (Hz). Due
to pump affinity laws, a pump running at 1 to 2 Hz below
motor nameplate frequency design will not meet its
performance curve. Conversely, a pump running at 1 to 2
Hz above may trip overloads.
Generator Operation
Always start the generator before the motor is started
and always stop the motor before the generator is shut
down. The motor thrust bearing may be damaged if
the generator is allowed to coast down with the motor
running. This same condition occurs when the generator
is allowed to run out of fuel.
Follow generator manufacturer’s recommendations for
de-rating at higher elevations or using natural gas.
Table 5 Engine Driven Generators
NOTE: This chart applies to 3-wire or 3-phase
motors. For best starting of 2-wire motors, the
minimum generator rating is 50% higher than shown.
MOTOR RATING
HP
KW
1/3
1/2
3/4
1
1.5
2
3
5
7.5
10
15
20
25
30
40
50
60
75
100
125
150
175
200
0.25
0.37
0.55
0.75
1.1
1.5
2.2
3.7
5.5
7.5
11
15
18.5
22
30
37
45
55
75
93
110
130
150
MINIMUM RATING OF GENERATOR
EXTERNALLY REGULATED
INTERNALLY REGULATED
KW
KVA
KW
KVA
1.5
1.9
1.2
1.5
2
2.5
1.5
1.9
3
3.8
2
2.5
4
5.0
2.5
3.13
5
6.25
3
3.8
7.5
9.4
4
5
10
12.5
5
6.25
15
18.75
7.5
9.4
20
25.0
10
12.5
30
37.5
15
18.75
40
50
20
25
60
75
25
31
75
94
30
37.50
100
125
40
50
100
125
50
62.5
150
188
60
75
175
220
75
94
250
313
100
125
300
375
150
188
375
469
175
219
450
563
200
250
525
656
250
313
600
750
275
344
WARNING: To prevent accidental electrocution,
automatic or manual transfer switches must be used
any time a generator is used as standby or back
up on power lines. Contact power company for use
and approval.
5SE OF #HECK 6ALVES
It is recommended that one or more check valves always
be used in submersible pump installations. If the pump
does not have a built-in check valve, a line check valve
should be installed in the discharge line within 25 feet
of the pump and below the draw down level of the water
supply. For deeper settings, check valves should be
installed per the manufacturer’s recommendations. More
than one check valve may be required, but more than the
recommended number of check valves should not
be used.
hammer and upthrust. Any of these can lead to early
pump or motor failure.
NOTE: Only positive sealing check valves should be
used in submersible installations. Although drilling the
check valves or using drain-back check valves may
prevent back spinning, they create upthrust and water
hammer problems.
Swing type check valves are not acceptable and should
never be used with submersible motors/pumps. Swing
type check valves have a slower reaction time which can
cause water hammer (see next page). Internal pump
check valves or spring loaded check valves close quickly
and help eliminate water hammer.
A. Backspin - With no check valve or a failed check
valve, the water in the drop pipe and the water in the
system can flow down the discharge pipe when the
motor stops. This can cause the pump to rotate in
a reverse direction. If the motor is started while it is
backspinning, an excessive force is placed across
the pump-motor assembly that can cause impeller
damage, motor or pump shaft breakage, excessive
bearing wear, etc.
Check valves are used to hold pressure in the system
when the pump stops. They also prevent backspin, water
B. Upthrust - With no check valve, a leaking check
valve, or drilled check valve, the unit starts under
5
!00,)#!4)/.
!LL -OTORS
a zero head condition. This causes an uplifting or
upthrust on the impeller-shaft assembly in the pump.
This upward movement carries across the pumpmotor coupling and creates an upthrust condition in
the motor. Repeated upthrust can cause premature
failure of both the pump and the motor.
the discharge piping. On the next pump start, water
moving at very high velocity fills the void and strikes
the closed check valve and the stationary water in the
pipe above it, causing a hydraulic shock. This shock
can split pipes, break joints and damage the pump
and/or motor. Water hammer can often be heard or
felt. When discovered, the system should be shut
down and the pump installer contacted to correct
the problem.
C. Water Hammer - If the lowest check valve is more
than 30 feet above the standing (lowest static)
water level, or a lower check valve leaks and the
check valve above holds, a vacuum is created in
7ELLS n ,ARGE $IAMETER 5NCASED 4OP &EEDING AND 3CREENED 3ECTIONS
Franklin Electric submersible motors are designed to
operate with a cooling flow of water over and around the
full length of the motor.
s 7ELL DIAMETER IS TOO LARGE TO MEET TABLE
flow requirements.
If the pump installation does not provide the minimum flow
shown in table 6, a flow inducer sleeve (flow sleeve) must
be used. The conditions requiring a flow sleeve are:
s 0UMP IS IN A ROCK WELL OR BELOW THE WELL CASING
s 0UMP IS IN AN OPEN BODY OF WATER
s 4HE WELL IS hTOP FEEDINGv AKA CASCADING
s 0UMP IS SET IN OR BELOW SCREENS OR PERFORATIONS
7ATER 4EMPERATURE AND &LOW
Franklin Electric’s standard submersible motors, except
Hi-Temp designs (see note below), are designed to
operate up to maximum service factor horsepower in
water up to 86 °F (30 °C). A flow of 0.25 ft/s for 4" motors
rated 3 hp and higher, and 0.5 ft/s for 6" and 8" motors is
required for proper cooling. Table 6 shows minimum flow
rates, in gpm, for various well diameters and motor sizes.
Table 6 Required Cooling Flow
MINIMUM GPM REQUIRED FOR MOTOR COOLING IN WATER UP TO 86 °F (30 °C).
If a standard motor is operated in water over 86 °F
(30 °C), water flow past the motor must be increased to
maintain safe motor operating temperatures. See
HOT WATER APPLICATIONS on page 7.
NOTE: Franklin Electric offers a line of Hi-Temp motors
designed to operate in water at higher temperatures or
lower flow conditions. Consult factory for details.
CASING OR
SLEEVE ID
INCHES (MM)
4" MOTOR (3-10 HP)
0.25 FT/S
GPM (L/M)
6" MOTOR
0.50 FT/S
GPM (L/M)
8" MOTOR
0.50 FT/S
GPM (L/M)
4 (102)
1.2 (4.5)
-
-
5 (127)
7 (26.5)
-
-
6 (152)
13 (49)
9 (34)
-
7 (178)
20 (76)
25 (95)
-
8 (203)
30 (114)
45 (170)
10 (40)
10 (254)
50 (189)
90 (340)
55 (210)
12 (305)
80 (303)
140 (530)
110 (420)
14 (356)
110 (416)
200 (760)
170 (645)
16 (406)
150 (568)
280 (1060)
245 (930)
0.25 ft/s = 7.62 cm/sec 0.50 ft/s = 15.24 cm/sec
1 inch = 2.54 cm
&LOW )NDUCER 3LEEVE
If the flow rate is less than specified, then a
flow inducer sleeve must be used. A flow
sleeve is always required in an open body
of water. FIG. 1 shows a typical flow inducer
sleeve construction.
WORM GEAR
CLAMPS
SAW CUTS
INTAKE
NOTCH OUT
FOR CABLE
GUARD
EXAMPLE: A 6" motor and pump that delivers
60 gpm will be installed in a 10" well.
FLOW INDUCER
SLEEVE
From table 6, 90 gpm would be required to
maintain proper cooling. In this case adding
an 8" or smaller flow sleeve provides the
required cooling.
SUBMERSIBLE
MOTOR
LOCK NUTS
INSIDE SLEEVE
BOTTOM END VIEW
CENTERING BOLT
FIG. 1
CENTERING BOLTS
MUST BE LOCATED
ON MOTOR CASTING.
DO NOT LOCATE ON
STATOR SHELL.
CENTERING
BOLT HOLE
(3 REQUIRED)
6
!00,)#!4)/.
!LL -OTORS
(EAD ,OSS &ROM &LOW 0AST -OTOR
Table 7 lists the approximate head loss due to flow
between an average length motor and smooth casing or
flow inducer sleeve.
Table 7 Head Loss in Feet (Meters) at Various Flow Rates
4"
4"
4"
6"
6"
6"
8"
8"
CASING ID IN INCHES (MM)
4 (102)
5 (127)
6 (152)
6 (152)
7 (178)
8 (203)
8.1 (206)
10 (254)
Flow Rate in gpm (l/m)
MOTOR DIAMETER
25 (95)
0.3 (.09)
50 (189)
1.2 (.37)
100 (378)
4.7 (1.4)
150 (568)
10.2 (3.1)
0.3 (.09)
1.7 (.52)
0.6 (.18)
0.2 (.06)
3.7 (1.1)
200 (757)
1.1 (.34)
0.4 (.12)
6.3 (1.9)
0.5 (.15)
6.8 (2.1)
250 (946)
1.8 (.55)
0.7 (.21)
9.6 (2.9)
0.8 (.24)
10.4 (3.2)
300 (1136)
2.5 (.75)
1.0 (.30)
13.6 (4.1)
1.2 (.37)
0.2 (.06)
14.6 (4.5)
23.7 (7.2)
2.0 (.61)
0.4 (.12)
24.6 (7.5)
500 (1893)
3.1 (.94)
0.7 (.21)
37.3 (11.4)
0.6 (0.2)
600 (2271)
4.4 (1.3)
1.0 (.30)
52.2 (15.9)
0.8 (0.3)
400 (1514)
800 (3028)
1.5 (0.5)
1000 (3785)
2.4 (0.7)
(OT 7ATER !PPLICATIONS 3TANDARD -OTORS
Franklin Electric offers a line of Hi-Temp motors
which are designed to operate in water with
various temperatures up to 194 °F (90 °C) without
increased flow. When a standard pump-motor
operates in water hotter than 86 °F (30 °C), a flow
rate of at least 3 ft/s is required. When selecting
the motor to drive a pump in over 86 °F (30 °C)
water, the motor horsepower must be de-rated per
the following procedure.
1. Using table 7A, determine pump gpm required
for different well or sleeve diameters. If
necessary, add a flow sleeve to obtain at least
3 ft/s flow rate.
7
Table 7A Minimum gpm (l/m) Required for
3 ft/s (.91 m/sec) Flow Rate
CASING OR
SLEEVE ID
4" HIGH
THRUST MOTOR
6" MOTOR
GPM
(L/M)
52
(197)
150
(568)
8" MOTOR
INCHES
(MM)
GPM
(L/M)
4
(102)
15
(57)
GPM
(L/M)
5
(127)
80
(303)
6
(152)
160
(606)
7
(178)
8
(203)
260
(984)
60
(227)
10
(254)
520
(1970)
330
(1250)
12
(305)
650
(2460)
14
(356)
1020
(3860)
16
(406)
1460
(5530)
Continued on next page
!00,)#!4)/.
!LL -OTORS
2. Determine pump horsepower required
from the pump manufacturer’s curve.
Brake Horsepower
6
EXAMPLE
5
A
B
4
C
3
2
1
0
0
5
10
15
20
25
30
35
40
45
50
Gallons Per Minute
FIG. 2 MANUFACTURER’S PUMP CURVE
Table 8 Heat Factor Multiplier at 3 ft/s (.91 m/sec) Flow Rate
3. Multiply the pump horsepower required by
the heat factor multiplier from table 8.
MAXIMUM
WATER TEMPERATURE
1/3 - 5 HP
.25 - 3.7 KW
7 1/2 - 30 HP
5.5 - 22 KW
OVER 30 HP
OVER 22 KW
140 °F (60 °C)
1.25
1.62
2.00
131 °F (55 °C)
1.11
1.32
1.62
122 °F (50 °C)
1.00
1.14
1.32
113 °F (45 °C)
1.00
1.00
1.14
104 °F (40 °C)
1.00
1.00
1.00
95 °F (35 °C)
1.00
1.00
1.00
Table 8A Service Factor Horsepower
4. Select a rated hp motor on table 8A whose
Service Factor Horsepower is at least the
value calculated in Item 3.
(OT 7ATER !PPLICATIONS
HP
KW
SFHP
HP
KW
SFHP
HP
KW
SFHP
HP
KW
SFHP
1/3
0.25
0.58
3
2.2
3.45
25
18.5
28.75
100
75
115.00
1/2
0.37
0.80
5
3.7
5.75
30
22.0
34.50
125
93
143.75
3/4
0.55
1.12
7.5
5.5
8.62
40
30.0
46.00
150
110
172.50
1
0.75
1.40
10
7.5
11.50
50
37.0
57.50
175
130
201.25
1.5
1.10
1.95
15
11.0
17.25
60
45.0
69.00
200
150
230.00
2
1.50
2.50
20
15.0
23.00
75
55.0
86.25
%XAMPLE
EXAMPLE: A 6" pump end requiring 39 hp input will
pump 124 °F water in an 8" well at a delivery rate of 140
gpm. From table 7A, a 6" flow sleeve will be required to
increase the flow rate to at least 3 ft/s.
Using table 8, the 1.62 heat factor multiplier is selected
because the hp required is over 30 hp and water
temperature is above 122 °F. Multiply 39 hp x 1.62
(multiplier), which equals 63.2 hp. This is the minimum
rated service factor horsepower usable at 39 hp in 124 °F.
Using table 8A, select a motor with a rated service factor
horsepower above 63.2 hp. A 60 hp motor has a service
factor horsepower of 69, so a 60 hp motor may be used.
8
!00,)#!4)/.
!LL -OTORS
$RAWDOWN 3EALS
Allowable motor temperature is based on atmospheric
PRESSURE OR HIGHER SURROUNDING THE MOTOR h$RAWDOWN
SEALS v WHICH SEAL THE WELL TO THE PUMP ABOVE ITS INTAKE
to maximize delivery, are not recommended, since the
suction created can be lower than atmospheric pressure.
'ROUNDING #ONTROL "OXES AND 0ANELS
The National Electrical Code requires that the control box
or panel-grounding terminal always be connected to supply
ground. If the circuit has no grounding conductor and no
metal conduit from the box to supply panel, use a wire at
least as large as line conductors and connect as required
by the National Electrical Code, from the grounding terminal
to the electrical supply ground.
WARNING: Failure to ground the control frame can
result in a serious or fatal electrical shock hazard.
'ROUNDING 3URGE !RRESTORS
An above ground surge arrestor must be grounded,
metal to metal, all the way to the lowest draw down water
strata for the surge arrestor to be effective. GROUNDING
THE ARRESTOR TO THE SUPPLY GROUND OR TO
A DRIVEN GROUND ROD PROVIDES LITTLE OR NO
SURGE PROTECTION FOR THE MOTOR.
#ONTROL "OX 0UMPTEC 0RODUCTS AND 0ANEL %NVIRONMENT
Franklin Electric control boxes, Pumptec products and
three-phase panels meet UL requirements for NEMA
Type 3R enclosures. They are suitable for indoor and
outdoor applications within temperatures of +14 °F
(-10 °C) to 122 °F (50 °C). Operating control boxes below
+14 °F can cause reduced starting torque and loss of
overload protection when overloads are located in
control boxes.
Control boxes, Pumptec products and three-phase
panels should never be mounted in direct sunlight or
high temperature locations. This will cause shortened
capacitor life (where applicable) and unnecessary
tripping of overload protectors. A ventilated enclosure
painted white to reflect heat is recommended for an
outdoor, high temperature location.
A damp well pit, or other humid location, accelerates
component failure from corrosion.
Control boxes with voltage relays are designed for
vertical upright mounting only. Mounting in other
positions will affect the operation of the relay.
%QUIPMENT 'ROUNDING
WARNING: Serious or fatal electrical shock may
result from failure to connect the motor, control
enclosures, metal plumbing and all other metal
near the motor or cable to the power supply ground
terminal using wire no smaller than motor cable wires.
The primary purpose of grounding the metal drop pipe
and/or metal well casing in an installation is safety. It is
done to limit the voltage between nonelectrical (exposed
metal) parts of the system and ground, thus minimizing
dangerous shock hazards. Using wire at least the size of
the motor cable wires provides adequate current-carrying
capability for any ground fault that might occur. It also
provides a low resistance path to ground, ensuring that
the current to ground will be large enough to trip any
overcurrent device designed to detect faults (such as a
ground fault circuit interrupter, or GFCI).
Normally, the ground wire to the motor would provide the
9
primary path back to the power supply ground for any
ground fault. There are conditions, however, where the
ground wire connection could become compromised.
One such example would be the case where the water
in the well is abnormally corrosive or aggressive. In this
example, a grounded metal drop pipe or casing would
then become the primary path to ground. However,
the many installations that now use plastic drop pipes
and/or casings require further steps to be taken for
safety purposes, so that the water column itself does not
become the conductive path to ground.
When an installation has abnormally corrosive water
AND the drop pipe or casing is plastic, Franklin Electric
recommends the use of a GFCI with a 10 mA set-point.
In this case, the motor ground wire should be routed
through the current-sensing device along with the motor
power leads. Wired this way, the GFCI will trip only when
a ground fault has occurred AND the motor ground wire
is no longer functional.
!00,)#!4)/.
3INGLE 0HASE -OTORS
7IRE #ONTROL "OXES
Single-phase three-wire submersible motors require the
use of control boxes. Operation of motors without control
boxes or with incorrect boxes can result in motor failure
and voids warranty.
Control boxes contain starting capacitors, a starting
relay, and, in some sizes, overload protectors, running
capacitors and contactors.
Ratings through 1 hp may use either a Franklin Electric
solid state QD or a potential (voltage) type starting relay,
while larger ratings use potential relays.
Potential (Voltage) Relays
Potential relays have normally closed contacts. When
power is applied, both start and main motor windings
are energized, and the motor starts. At this instant, the
voltage across the start winding is relatively low and not
enough to open the contacts of the relay.
As the motor accelerates, the increasing voltage across
the start winding (and the relay coil) opens the relay
contacts. This opens the starting circuit and the motor
continues to run on the main winding alone, or the main
plus run capacitor circuit. After the motor is started the
relay contacts remain open.
CAUTION: The control box and motor are two pieces
of one assembly. Be certain that the control box and
motor hp and voltage match. Since a motor is designed
to operate with a control box from the same
manufacturer, we can promise warranty coverage
only when a Franklin control box is used with a
Franklin motor.
7IRE -OTOR 3OLID 3TATE #ONTROLS
BIAC Switch Operation
When power is applied the bi-metal switch contacts are
closed, so the triac is conducting and energizes the start
winding. As rpm increases, the voltage in the sensor coil
generates heat in the bi-metal strip, causing the bi-metal
strip to bend and open the switch circuit. This removes
the starting winding and the motor continues to run on
the main winding alone.
to restart the motor before the starting switch has reset,
the motor may not start; however, there will be current in
the main winding until the overload protector interrupts
the circuit. The time for the protector to reset is longer
than the reset of the starting switch. Therefore, the start
switch will have closed and the motor will operate.
Approximately 5 seconds after power is removed from
the motor, the bi-metal strip cools sufficiently to return
to its closed position and the motor is ready for the next
start cycle.
A waterlogged tank will cause fast cycling. When a
waterlogged condition does occur, the user will be
alerted to the problem during the off time (overload reset
time) since the pressure will drop drastically. When the
waterlogged tank condition is detected, the condition
should be corrected to prevent nuisance tripping of the
overload protector.
Rapid Cycling
Bound Pump (Sandlocked)
The BIAC starting switch will reset within approximately 5
seconds after the motor is stopped. If an attempt is made
CAUTION: Restarting the motor within 5 seconds
after power is removed may cause the motor overload
to trip.
When the motor is not free to turn, as with a sandlocked
PUMP THE ")!# SWITCH CREATES A hREVERSE IMPACT
TORQUEv IN THE MOTOR IN EITHER DIRECTION 7HEN THE SAND IS
dislodged, the motor will start and operate in the
correct direction.
1$ 2ELAYS 3OLID 3TATE
There are two elements in the relay: a reed switch and
a triac. The reed switch consists of two tiny rectangular
blade-type contacts, which bend under magnetic flux. It
is hermetically sealed in glass and is located within a coil,
which conducts line current. When power is supplied to
the control box, the main winding current passing through
the coil immediately closes the reed switch contacts.
This turns on the triac, which supplies voltage to the start
winding, thus starting the motor.
Once the motor is started, the operation of the QD relay
is an interaction between the triac, the reed switch and
the motor windings. The solid state switch senses motor
speed through the changing phase relationship between
start winding current and line current. As the motor
approaches running speed, the phase angle between
the start current and the line current becomes nearly
in phase. At this point, the reed switch contacts open,
turning off the triac. This removes voltage from the start
winding and the motor continues to run on the main
winding only. With the reed switch contacts open and
the triac turned off, the QD relay is ready for the next
starting cycle.
10
!00,)#!4)/.
3INGLE 0HASE -OTORS
OR 7IRE #ABLE (Z (Service Entrance to Motor - Maximum Length In Feet)
60 °C
Table 11
MOTOR RATING
60 °C INSULATION - AWG COPPER WIRE SIZE
VOLTS
HP
KW
14
12
10
8
6
4
3
2
1
0
00
000
0000
115
1/2
.37
100
160
250
390
620
960
1190
1460
1780
2160
2630
3140
3770
1/2
.37
400
650
1020
1610
2510
3880
4810
5880
7170
8720
3/4
.55
300
480
760
1200
1870
2890
3580
4370
5330
6470
7870
1
.75
250
400
630
990
1540
2380
2960
3610
4410
5360
6520
1.5
1.1
190
310
480
770
1200
1870
2320
2850
3500
4280
5240
2
1.5
150
250
390
620
970
1530
1910
2360
2930
3620
4480
3
2.2
120
190
300
470
750
1190
1490
1850
2320
2890
3610
5
3.7
0
0
180
280
450
710
890
1110
1390
1740
2170
2680
7.5
5.5
0
0
0
200
310
490
610
750
930
1140
1410
1720
10
7.5
0
0
0
0
250
390
490
600
750
930
1160
1430
1760
15
11
0
0
0
0
170
270
340
430
530
660
820
1020
1260
230
75 °C
Table 11A
MOTOR RATING
75 °C INSULATION - AWG COPPER WIRE SIZE
VOLTS
HP
KW
14
12
10
8
6
4
3
2
1
0
00
000
0000
115
1/2
.37
100
160
250
390
620
960
1190
1460
1780
2160
2630
3140
3770
1/2
.37
400
650
1020
1610
2510
3880
4810
5880
7170
8720
3/4
.55
300
480
760
1200
1870
2890
3580
4370
5330
6470
7870
9380
1
.75
250
400
630
990
1540
2380
2960
3610
4410
5360
6520
7780
9350
1.5
1.1
190
310
480
770
1200
1870
2320
2850
3500
4280
5240
6300
7620
2
1.5
150
250
390
620
970
1530
1910
2360
2930
3620
4480
5470
6700
3
2.2
120
190
300
470
750
1190
1490
1850
2320
2890
3610
4470
5550
5
3.7
0
110
180
280
450
710
890
1110
1390
1740
2170
2680
3330
7.5
5.5
0
0
120
200
310
490
610
750
930
1140
1410
1720
2100
10
7.5
0
0
0
160
250
390
490
600
750
930
1160
1430
1760
15
11
0
0
0
0
170
270
340
430
530
660
820
1020
1260
230
1 Foot = .3048 Meter
Lengths in BOLD only meet the US National Electrical
Code ampacity requirements for individual conductors
60 °C or 75 °C in free air or water, not in magnetic
enclosures, conduit or direct buried.
Lengths NOT in bold meet the NEC ampacity
requirements for either individual conductors or jacketed
60 °C or 75 °C cable and can be in conduit or direct
buried. Flat molded and web/ribbon cable are considered
jacketed cable.
The portion of the total cable length, which is between
the supply and single-phase control box with a line
contactor, should not exceed 25% of total maximum
allowable to ensure reliable contactor operation. Singlephase control boxes without line contactors may be
connected at any point in the total cable length.
Tables 11 & 11A are based on copper wire. If aluminum
wire is used, it must be two sizes larger than copper wire
and oxidation inhibitors must be used on connections.
If any other cable is used, the NEC and local codes
should be observed.
EXAMPLE: If tables 11 & 11A call for #12 copper wire,
#10 aluminum wire would be required.
Cable lengths in tables 11 & 11A allow for a 5% voltage
drop running at maximum nameplate amperes. If 3%
voltage drop is desired, multiply table 11 and 11A lengths
by 0.6 to get maximum cable length.
Contact Franklin Electric for 90 °C cable lengths. See
pages 15, 49, and 50 for applications using 230 V motors
on 208 V power systems.
11
!00,)#!4)/.
3INGLE 0HASE -OTORS
4WO OR -ORE $IFFERENT #ABLE 3IZES #AN "E 5SED
Depending on the installation, any number of
combinations of cable may be used.
occurs in this wire. This leaves us 46.7% (1.00 - 0.533
= 0.467) of some other wire size to use in the remaining
FEET hDOWN HOLEv WIRE RUN
For example, in a replacement/upgrade installation, the
well already has 160 feet of buried #10 cable between
the service entrance and the wellhead. A new 3 hp,
230-volt, single-phase motor is being installed to replace
a smaller motor. The question is: Since there is already
160 feet of #10 AWG installed, what size cable is
required in the well with a 3 hp, 230-volt, single-phase
motor setting at 310 feet?
The table shows #8 AWG copper wire is good for 470
feet. Using the formula again, 310 feet (used) ÷ 470 feet
(allowed) = 0.660; adding this to the 0.533 determined
earlier; 0.533 + 0.660 = 1.193. This combination is
greater than 1.00, so the voltage drop will not meet US
National Electrical Code recommendations.
Tables 11 & 11A show #6 AWG copper wire is good for
750 feet. Using the formula, 310 ÷ 750 = 0.413, and
using these numbers, 0.533 + 0.413 = 0.946, we find this
is less than 1.00 and will meet the NEC recommended
voltage drop.
From tables 11 & 11A, a 3 hp motor can use up to 300
feet of #10 AWG cable.
The application has 160 feet of #10 AWG copper
wire installed.
This works for two, three or more combinations of wire
and it does not matter which size wire comes first in
the installation.
Using the formula below, 160 feet (actual) ÷ 300 feet
(max allowable) is equal to 0.533. This means 53.3%
(0.533 x 100) of the allowable voltage drop or loss, which
is allowed between the service entrance and the motor,
Formula:
Actual Length
Max Allowed
+
Actual Length
Max Allowed
=
1.00
EXAMPLE: 3 hp, 230-Volt, Single-Phase Motor
310 ft #6 AWG
(41.3% of allowable cable)
160 ft #10 AWG
(53.3% of allowable cable)
FIG. 3
3 hp, 230 V
Single-Phase Motor
12
!00,)#!4)/.
3INGLE 0HASE -OTORS
Table 13 Single-Phase Motor Specifications (60 Hz) 3450 rpm
FULL
LOAD
MAXIMUM
LOAD
(2)
WATTS
AMPS
12.0
960
6.0
960
8.0
1310
10.4
1600
13.1
2280
Y12.0
B12.0
960
R0
Y6.0
B6.0
960
R0
Y8.0
B8.0
1310
R0
10.4
10.4
1600
R0
HP
KW
VOLTS
HZ
S.F.
244504
244505
244507
244508
244309
1/2
1/2
3/4
1
1.5
0.37
0.37
0.55
0.75
1.1
115
230
230
230
230
60
60
60
60
60
1.6
1.6
1.5
1.4
1.3
214504
1/2
0.37
115
60
1.6
214505
1/2
0.37
230
60
1.6
214507
3/4
0.55
230
60
1.5
214508
1
0.75
230
60
1.4
214505
1/2
0.37
230
60
1.6
Y3.6
B3.7
R2.0
655
Y4.3
B4.0
R2.0
214507
3/4
0.55
230
60
1.5
Y4.9
B5.0
R3.2
925
214508
1
0.75
230
60
1.4
Y6.0
B5.7
R3.4
1160
214508
W/11.5 CB
1
0.75
230
60
1.4
224300
1.5
1.1
230
60
1.3
224301
2
1.5
230
60
1.25
224302
(3)
3
2.2
230
60
1.15
224303
(4)
5
3.7
230
60
1.15
226110
(5)
5
3.7
230
60
1.15
226111
7.5
5.5
230
60
1.15
226112
10
7.5
230
60
1.15
226113
15
11
230
60
1.15
6"
4" 3-WIRE
4" 3-WIRE W/CRC CB
4" 3-WIRE
TYPE
4" 2-WIRE
RATING
MOTOR
MODEL
PREFIX
(2)
AMPS
10.0
5.0
6.8
8.2
10.6
Y10.0
B10.0
R0
Y5.0
B5.0
R0
Y6.8
B6.8
R0
Y8.2
B8.2
R0
Y6.6
B6.6
R1.3
Y10.0
B9.9
R1.3
Y10.0
B9.3
R2.6
Y14.0
B11.2
R6.1
Y23.0
B15.9
R11.0
Y23.0
B14.3
R10.8
Y36.5
B34.4
R5.5
Y44.0
B39.5
R9.3
Y62.0
B52.0
R17.5
(1) Main winding - yellow to black
Start winding - yellow to red
(2) Y = Yellow lead - line amps
B = Black lead - main winding amps
R = Red lead - start or auxiliary winding amps
(3) Control Boxes date coded 02C and older have
35 MFD run capacitors. Current values should
be Y14.0 @ FL and Y17.0 @ Max Load.
B12.2
B14.5
R4.7
R4.5
WATTS
670
670
940
1210
1770
670
670
940
1210
1130
1620
2025
3000
4830
4910
7300
9800
13900
WINDING (1)
RES. IN OHMS
M=MAIN RES.
S=START RES.
1.0-1.3
4.2-5.2
3.0-3.6
2.2-2.7
1.5-2.1
EFFICIENCY %
POWER
FACTOR %
S.F.
F.L.
S.F.
62
62
64
65
64
56
56
59
62
63
73
73
74
74
83
M1.0-1.3
S4.1-5.1
62
56
M4.2-5.2
S16.7-20.5
62
M3.0-3.6
S10.7-13.1
F.L.
LOCKED
ROTOR
AMPS
KVA
CODE
58
58
62
63
76
64.4
32.2
40.7
48.7
66.2
R
R
N
N
M
73
58
50.5
M
56
73
58
23
M
64
59
74
62
34.2
M
M2.2-2.7
S9.9-12.1
65
62
74
63
41.8
L
890
M4.2-5.2
S16.7-20.5
67
57
90
81
23
M
Y5.7
B5.2
R3.1
1220
M3.0-3.6
S10.7-13.1
69
60
92
84
34.2
M
Y7.1
B6.2
R3.3
1490
M2.2-2.7
S9.9-12.1
70
64
92
86
41.8
L
1500
M2.2-2.7
S9.9-12.1
70
66
82
72
43
L
2080
M1.7-2.1
S7.5-9.2
70
69
85
79
51.4
J
2555
M1.8-2.3
S5.5-7.2
73
74
95
94
53.1
G
3400
M1.1-1.4
S4.0-4.8
75
75
99
99
83.4
H
5500
M.71-.82
S1.8-2.2
78
77
100
100
129
G
5570
M.55-.68
S1.3-1.7
77
76
100
99
99
E
8800
M.36-.50
S.88-1.1
73
74
91
90
165
F
11300
M.27-.33
S.80-.99
76
77
96
96
204
E
16200
M.17-.22
S.68-.93
79
80
97
98
303
E
Y8.0
B7.9
R1.3
Y11.5
B11.0
R1.3
Y13.2
B11.9
R2.6
Y17.0
B12.6
R6.0
Y27.5
B19.1
R10.8
Y27.5
B17.4
R10.5
Y42.1
B40.5
R5.4
Y51.0
B47.5
R8.9
Y75.0
B62.5
R16.9
(4) Control Boxes date coded 01M and older have
60 MFD run capacitors and the current values on
a 4" motor will be Y23.0 @ FL - Y27.5 @ Max Load.
B19.1
B23.2
R8.0
R7.8
(5) Control Boxes date coded 01M and older have
60 MFD run capacitors and the current values on
a 6" motor will be Y23.0 @ FL -Y27.5 @ Max Load.
B18.2
B23.2
R8.0
R7.8
Performance is typical, not guaranteed, at specified voltages and specified capacitor values. Performance at voltage
ratings not shown is similar, except amps vary inversely with voltage.
13
!00,)#!4)/.
3INGLE 0HASE -OTORS
Table 14 Single-Phase Motor Fuse Sizing
4" 3-WIRE W/CRC CB
4" 3-WIRE
4" 2-WIRE
TYPE
MOTOR
MODEL
PREFIX
CIRCUIT BREAKERS OR FUSE AMPS
(MAXIMUM PER NEC)
(TYPICAL SUBMERSIBLE)
HP
KW
VOLTS
STANDARD
FUSE
DUAL ELEMENT
TIME DELAY
FUSE
CIRCUIT
BREAKER
STANDARD
FUSE
DUAL ELEMENT
TIME DELAY
FUSE
CIRCUIT
BREAKER
244504
1/2
0.37
115
35
20
30
30
15
30
244505
1/2
0.37
230
20
10
15
15
8
15
244507
3/4
0.55
230
25
15
20
20
10
20
244508
1
0.75
230
30
20
25
25
11
25
244309
1.5
1.1
230
35
20
30
35
15
30
214504
1/2
0.37
115
35
20
30
30
15
30
214505
1/2
0.37
230
20
10
15
15
8
15
214507
3/4
0.55
230
25
15
20
20
10
20
214508
1
0.75
230
30
20
25
25
11
25
214505
1/2
0.37
230
20
10
15
15
8
15
214507
3/4
0.55
230
25
15
20
20
10
20
214508
1
0.75
230
30
20
25
25
11
25
1
0.75
230
30
20
25
25
11
25
224300
1.5
1.1
230
35
20
30
30
15
30
224301
2
1.5
230
30
20
25
30
15
25
224302
3
2.2
230
45
30
40
45
20
40
224303
5
3.7
230
80
45
60
70
30
60
226110
5
3.7
230
80
45
60
70
30
60
226111
7.5
5.5
230
125
70
100
110
50
100
226112
10
7.5
230
150
80
125
150
60
125
226113
15
11
230
200
125
175
200
90
175
214508
W/ 1-1.5 CB
6"
4" 3-WIRE
CIRCUIT BREAKERS OR FUSE AMPS
RATING
14
!00,)#!4)/.
3INGLE 0HASE -OTORS
!UXILIARY 2UNNING #APACITORS
!DDED CAPACITORS MUST BE CONNECTED ACROSS h2EDv AND
h"LACKv CONTROL BOX TERMINALS IN PARALLEL WITH ANY EXISTING
running capacitors. The additional capacitor(s) should
be mounted in an auxiliary box. The values of additional
running capacitors most likely to reduce noise are given
below. The tabulation gives the max. S.F. amps normally
in each lead with the added capacitor.
Although motor amps decrease when auxiliary
run capacitance is added, the load on the motor
does not. If a motor is overloaded with normal
capacitance, it still will be overloaded with auxiliary
run capacitance, even though motor amps may be
within nameplate values.
Table 15 Auxiliary Capacitor Sizing
MOTOR RATING
NORMAL RUNNING
CAPACITOR(S)
AUXILIARY RUNNING CAPACITORS FOR
NOISE REDUCTION
MAXIMUM AMPS WITH RUN CAP
HP
VOLTS
MFD
MFD
MIN. VOLTS
FRANKLIN PART
YELLOW
BLACK
RED
1/2
115
0
60(1)
370
TWO 155327101
8.4
7.0
4.0
1/2
0
15(1)
370
ONE 155328101
4.2
3.5
2.0
3/4
0
20(1)
370
ONE 155328103
5.8
5.0
2.5
7.1
5.6
3.4
1
0
25(1)
370
ONE EA. 155328101
155328102
1.5
10
20
370
ONE 155328103
9.3
7.5
4.4
20
10
370
ONE 155328102
11.2
9.2
3.8
45
NONE
370
17.0
12.6
6.0
80
NONE
370
2
230
3
5
7.5
45
45
370
ONE EA. 155327101
155328101
10
70
30
370
ONE 155327101
15
135
NONE
27.5
19.1
10.8
37.0
32.0
11.3
49.0
42.0
13.0
75.0
62.5
16.9
(1) Do not add running capacitors to 1/3 through 1 hp control boxes, which use solid state switches or QD relays.
Adding capacitors will cause switch failure. If the control box is converted to use a voltage relay, the specified
running capacitance can be added.
"UCK "OOST 4RANSFORMERS
wide range of voltage boost or buck are published by
transformer manufacturers, the following table shows
Franklin’s recommendations. The table, based on
boosting the voltage 10%, shows the minimum rated
transformer kVA needed and the common
standard transformer kVA.
When the available power supply voltage is not within
the proper range, a buck-boost transformer is often
used to adjust voltage to match the motor. The most
common usage on submersible motors is boosting a
208 volt supply to use a standard 230 volt single-phase
submersible motor and control. While tables to give a
Table 15A Buck-Boost Transformer Sizing
MOTOR HP
1/3
1/2
3/4
1
1.5
2
3
5
7.5
10
15
LOAD KVA
1.02
1.36
1.84
2.21
2.65
3.04
3.91
6.33
9.66
11.70
16.60
MINIMUM XFMR KVA
0.11
0.14
0.19
0.22
0.27
0.31
0.40
0.64
0.97
1.20
1.70
STANDARD XFMR KVA
0.25
0.25
0.25
0.25
0.50
0.50
0.50
0.75
1.00
1.50
2.00
Buck-Boost transformers are power transformers, not control transformers. They may also be used to lower voltage
when the available power supply voltage is too high.
15
!00,)#!4)/.
4HREE 0HASE -OTORS
Table 16 Three-Phase 60 °C Cable, 60 Hz (Service Entrance to Motor) Maximum Length in Feet
MOTOR RATING
VOLTS
200 V
60 Hz
ThreePhase
3 - Lead
230 V
60 Hz
ThreePhase
3 - Lead
380 V
60 Hz
ThreePhase
3 - Lead
60 °C INSULATION - AWG COPPER WIRE SIZE
HP
KW
14
12
10
8
6
4
3
1/2
0.37
710
1140
1800
2840
4420
3/4
0.55
510
810
1280
2030
3160
1
0.75
430
690
1080
1710
1.5
1.1
310
500
790
1260
2670
4140
5140
1960
3050
2
1.5
240
390
610
3780
970
1520
2360
3
2.2
180
290
470
740
1160
1810
5
3.7
110
170
280
440
690
5.5
0
0
200
310
7.5
10
7.5
0
0
0
15
11
0
0
20
15
0
25
18.5
30
60 °C
MCM COPPER WIRE SIZE
2
1
0
00
000
0000
250
2940
3610
4430
5420
2250
2760
3390
4130
1080
1350
1660
2040
490
770
960
1180
230
370
570
720
0
160
250
390
0
0
0
190
0
0
0
0
22
0
0
0
1/2
0.37
930
1490
3/4
0.55
670
300
350
400
500
2490
3050
3670
4440
5030
1450
1770
2170
2600
3150
3560
880
1090
1330
1640
1970
2390
2720
490
600
740
910
1110
1340
3100
3480
3800
4420
1630
1850
2100
2350
2570
300
380
460
570
700
860
2980
1050
1270
1440
1650
1850
2020
0
240
300
370
460
570
2360
700
840
1030
1170
1330
1500
1640
0
0
0
250
310
380
470
1900
580
700
850
970
1110
1250
1360
2350
3700
5760
8910
1590
1080
1700
2580
4190
6490
8060
9860
910
1430
2260
3520
5460
6780
8290
1
0.75
560
1.5
1.1
420
670
1060
1670
2610
4050
5030
6160
7530
9170
2
1.5
320
510
810
1280
2010
3130
3890
4770
5860
7170
3
2.2
240
390
620
990
1540
2400
2980
3660
4480
5470
6690
8020
9680
5
3.7
140
230
370
590
920
1430
1790
2190
2690
3290
4030
4850
5870
6650
7560
8460
9220
7.5
5.5
0
160
260
420
650
1020
1270
1560
1920
2340
2870
3440
4160
4710
5340
5970
6500
7510
10
7.5
0
0
190
310
490
760
950
1170
1440
1760
2160
2610
3160
3590
4100
4600
5020
5840
15
11
0
0
0
210
330
520
650
800
980
1200
1470
1780
2150
2440
2780
3110
3400
3940
20
15
0
0
0
0
250
400
500
610
760
930
1140
1380
1680
1910
2180
2450
2680
3120
25
18.5
0
0
0
0
0
320
400
500
610
750
920
1120
1360
1540
1760
1980
2160
2520
0
0
260
330
410
510
620
760
930
1130
1280
1470
1650
1800
2110
8830
8780
30
22
0
0
0
1/2
0.37
2690
4290
6730
3/4
0.55
2000
3190
5010
7860
1
0.75
1620
2580
4060
6390
9980
1.5
1.1
1230
1970
3100
4890
7630
2
1.5
870
1390
2180
3450
5400
8380
3
2.2
680
1090
1710
2690
4200
6500
8020
9830
5
3.7
400
640
1010
1590
2490
3870
4780
5870
7230
7.5
5.5
270
440
690
1090
1710
2640
3260
4000
4930
6010
7290
8780
10
7.5
200
320
510
800
1250
1930
2380
2910
3570
4330
5230
6260
7390
8280
9340
15
11
0
0
370
590
920
1430
1770
2170
2690
3290
4000
4840
5770
6520
7430
8250
8990
20
15
0
0
0
440
700
1090
1350
1670
2060
2530
3090
3760
4500
5110
5840
6510
7120
8190
25
18.5
0
0
0
360
570
880
1100
1350
1670
2050
2510
3040
3640
4130
4720
5250
5740
6590
30
22
0
0
0
0
470
730
910
1120
1380
1700
2080
2520
3020
3430
3920
4360
4770
5490
40
30
0
0
0
0
0
530
660
820
1010
1240
1520
1840
2200
2500
2850
3170
3470
3990
50
37
0
0
0
0
0
0
540
660
820
1000
1220
1480
1770
2010
2290
2550
2780
3190
60
45
0
0
0
0
0
0
0
560
690
850
1030
1250
1500
1700
1940
2150
2350
2700
75
55
0
0
0
0
0
0
0
0
570
700
860
1050
1270
1440
1660
1850
2030
2350
100
75
0
0
0
0
0
0
0
0
0
510
630
760
910
1030
1180
1310
1430
1650
125
93
0
0
0
0
0
0
0
0
0
0
0
620
740
840
950
1060
1160
1330
150
110
0
0
0
0
0
0
0
0
0
0
0
0
620
700
790
880
960
1090
175
130
0
0
0
0
0
0
0
0
0
0
0
0
0
650
750
840
920
1070
200
150
0
0
0
0
0
0
0
0
0
0
0
0
0
0
630
700
760
880
Lengths in BOLD only meet the US National Electrical Code ampacity requirements for individual conductors in free air
or water. Lengths NOT in bold meet NEC ampacity requirements for either individual conductors or jacketed cable. See
page 11 for additional details.
Continued on next page
16
!00,)#!4)/.
4HREE 0HASE -OTORS
60 °C
Table 17 Three-Phase 60 °C Cable (Continued)
MOTOR RATING
VOLTS
KW
14
12
10
2
1
00
000
1/2
0.37
3770
6020
9460
3/4
0.55
2730
4350
6850
0.75
2300
3670
5770
9070
1.1
1700
2710
4270
6730
2
1.5
1300
2070
3270
5150
8050
3
2.2
1000
1600
2520
3970
6200
5
3.7
590
950
1500
2360
3700
5750
7.5
5.5
420
680
1070
1690
2640
10
7.5
310
500
790
1250
1960
4100
5100
6260
7680
3050
3800
4680
15
11
0
340
540
850
5750
7050
1340
2090
2600
3200
3930
20
15
0
0
410
650
1030
1610
2000
2470
3040
4810
5900
7110
3730
4580
25
18.5
0
0
0
530
830
1300
1620
1990
5530
2450
3010
3700
30
22
0
0
0
430
680
1070
1330
4470
5430
1640
2030
2490
3060
3700
40
30
0
0
0
0
500
790
980
1210
1490
1830
2250
2710
50
37
0
0
0
0
0
640
800
980
1210
1480
1810
60
45
0
0
0
0
0
540
670
830
1020
1250
75
55
0
0
0
0
0
0
0
680
840
100
75
0
0
0
0
0
0
0
0
125
93
0
0
0
0
0
0
0
150
110
0
0
0
0
0
0
130
0
0
0
0
0
200
150
0
0
0
0
0
1/2
0.37
5900
9410
3/4
0.55
4270
6810
1
0.75
3630
5800
9120
1.5
1.1
2620
4180
6580
2
1.5
2030
3250
5110
8060
3
2.2
1580
2530
3980
6270
5
3.7
920
1480
2330
3680
5750
7.5
5.5
660
1060
1680
2650
4150
10
7.5
490
780
1240
1950
15
11
330
530
850
1340
20
15
0
410
650
25
18.5
0
0
30
22
0
40
30
50
1.5
175
575 V
60 Hz
ThreePhase
3 - Lead
60
8
6
4
MCM COPPER WIRE SIZE
3
1
460 V
60 Hz
ThreePhase
3 - Lead
60 °C INSULATION - AWG COPPER WIRE SIZE
HP
0
0000
250
300
350
400
500
4500
5130
5860
3290
3730
4250
2190
2650
3010
1540
1850
2240
2540
3420
3830
4180
4850
2890
3240
3540
1030
1260
1520
1850
4100
2100
2400
2700
2950
620
760
940
1130
3440
1380
1560
1790
2010
2190
0
0
0
740
2550
890
1000
1220
1390
1560
1700
0
0
0
0
1960
0
760
920
1050 1190
1340
1460
0
0
0
0
1690
0
0
0
810
930
1060 1190
1300
0
0
0
1510
0
0
0
0
0
810
920
1030 1130
1310
3060
4770
5940
2090
3260
4060
1030
1610
2520
3140
520
830
1300
2030
2530
3860
4760
5830
3110
3840
0
430
680
1070
1670
4710
2080
2560
3160
0
0
0
500
790
3880
4770
5780
7030
8000
1240
1540
1900
2330
2860
3510
4230
5140
37
0
0
0
0
5830
640
1000
1250
1540
1890
2310
2840
3420
4140
45
0
0
0
4700
5340
5990
6530
7580
0
0
850
1060
1300
1600
1960
2400
2890
3500
3970
4520
5070
5530
0
6410
0
0
0
690
860
1060
1310
1600
1970
2380
2890
3290
3750
5220
4610
5370
75
55
0
100
75
0
0
0
0
0
0
0
790
970
1190
1460
1770
2150
2440
2790
3140
3430
3990
125
93
0
0
0
0
0
0
0
0
770
950
1160
1400
1690
1920
2180
2440
2650
3070
150
110
0
0
0
0
0
0
0
0
0
800
990
1190
1440
1630
1860
2080
2270
2640
175
130
0
0
0
0
0
0
0
0
0
0
870
1050 1270 1450
1650
1860
2030
2360
200
150
0
0
0
0
0
0
0
0
0
0
0
1110 1260 1440
1620
1760
2050
920
Lengths in BOLD only meet the US National Electrical Code ampacity requirements for individual conductors in free air
or water. Lengths NOT in bold meet NEC ampacity requirements for either individual conductors or jacketed cable. See
11 for additional details.
17
Continued on next page
!00,)#!4)/.
4HREE 0HASE -OTORS
60 °C
Table 18 Three-Phase 60 °C Cable (Continued)
MOTOR RATING
VOLTS
HP
KW
5
3.7
200 V
7.5
5.5
60 Hz
10
7.5
Three15
11
Phase
20
15
6 - Lead
25
18.5
Y-D
30
22
5
3.7
230 V
7.5
5.5
60 Hz
10
7.5
Three15
11
Phase
20
15
6 - Lead
25
18.5
Y-D
30
22
5
3.7
7.5
5.5
10
7.5
15
11
20
15
25
18.5
380 V
30
22
60 Hz
40
30
ThreePhase
50
37
6 - Lead
60
45
Y-D
75
55
100
75
125
93
150
110
175
130
200
150
5
3.7
7.5
5.5
10
7.5
15
11
20
15
25
18.5
460 V
30
22
60 Hz
40
30
ThreePhase
50
37
6 - Lead
60
45
Y-D
75
55
100
75
125
93
150
110
175
130
200
150
5
3.7
7.5
5.5
10
7.5
15
11
20
15
25
18.5
575 V
30
22
60 Hz
40
30
ThreePhase
50
37
6 - Lead
60
45
Y-D
75
55
100
75
125
93
150
110
175
130
200
150
14
12
10
8
160
110
80
0
0
0
0
210
150
110
0
0
0
0
600
400
300
210
160
0
0
0
0
0
0
0
0
0
0
0
880
630
460
310
230
190
0
0
0
0
0
0
0
0
0
0
1380
990
730
490
370
300
240
0
0
0
0
0
0
0
0
0
250
180
130
0
0
0
0
340
240
180
0
0
0
0
960
660
480
340
260
210
0
0
0
0
0
0
0
0
0
0
1420
1020
750
510
380
310
250
0
0
0
0
0
0
0
0
0
2220
1590
1170
790
610
490
400
300
0
0
0
0
0
0
0
0
420
300
210
140
0
0
0
550
390
280
190
140
0
0
1510
1030
760
550
410
330
270
0
0
0
0
0
0
0
0
0
2250
1600
1180
810
610
490
410
300
0
0
0
0
0
0
0
0
3490
2520
1860
1270
970
780
645
480
380
0
0
0
0
0
0
0
660
460
340
240
170
140
0
880
630
460
310
230
190
150
2380
1630
1200
880
660
540
430
320
250
0
0
0
0
0
0
0
3540
2530
1870
1270
970
790
640
480
370
320
0
0
0
0
0
0
5520
3970
2920
2010
1540
1240
1020
750
590
500
420
0
0
0
0
0
60 °C INSULATION - AWG COPPER WIRE SIZE
6
4
3
2
1
1030
730
550
370
280
220
180
1380
970
730
490
370
300
240
3730
2560
1870
1380
1050
850
700
510
400
340
0
0
0
0
0
0
5550
3960
2940
2010
1540
1240
1020
750
590
500
420
0
0
0
0
0
8620
6220
4590
3130
2410
1950
1600
1180
960
790
660
400
0
0
0
0
MCM COPPER WIRE SIZE
300
350
400
0
00
000
0000
250
3060
2170
1630
1110
850
690
570
4030
2880
2160
1470
1140
910
760
3730
2650
1990
1360
1050
850
700
4930
3510
2640
1800
1390
1120
930
4570
3250
2460
1660
1290
1050
870
6040
4300
3240
2200
1710
1380
1140
5500
3900
2950
2010
1570
1260
1050
7270
5160
3910
2670
2070
1680
1390
6660
4720
3580
2440
1900
1540
1270
8800
6240
4740
3220
2520
2040
1690
7540
5340
4080
2770
2160
1750
1450
9970
7060
5380
3660
2860
2310
1920
4650
3150
2470
1990
1660
5220
3520
2770
2250
1870
5700
3850
3030
2460
2040
6630
4470
3540
2850
2380
8010
6150
4170
3270
2640
2200
8950
6900
4660
3670
2970
2470
9750
7530
5100
4020
3240
2700
8760
5910
4680
3780
3160
7390
5350
4030
3090
2500
2070
1510
1230
1030
855
640
490
420
360
0
9010
6490
4930
3790
3070
2550
1860
1500
1270
1050
760
600
510
440
0
7840
6000
4630
3760
3120
2280
1830
1540
1290
940
730
620
540
480
9390
7260
5640
4560
3780
2760
2220
1870
1570
1140
930
750
660
580
8650
6750
5460
4530
3300
2650
2250
1900
1360
1110
930
780
690
9780
7660
6190
5140
3750
3010
2550
2160
1540
1260
1050
970
790
4260
7080
5880
4270
3430
2910
2490
1770
1420
1180
1120
940
9760
7870
6540
4750
3820
3220
2770
1960
1590
1320
1260
1050
8610
7150
5200
4170
3520
3040
2140
1740
1440
1380
1140
9880
8230
5980
4780
4050
3520
2470
1990
1630
1600
1320
9390
7020
4800
3700
2980
2460
1810
1470
1240
1020
760
590
510
0
0
8620
5890
4560
3670
3040
2230
1810
1530
1260
930
730
630
550
0
7210
5590
4510
3730
2740
2220
1870
1540
1140
880
770
680
590
8850
6870
5550
4590
3370
2710
2310
1890
1410
1110
950
830
730
8290
6700
5550
4060
3280
2770
2280
1690
1330
1140
1000
880
8140
6750
4930
3970
3360
2770
2070
1500
1380
1220
1070
7690
5590
4510
3810
3150
2340
1830
1570
1390
1210
8790
6370
5130
4330
3600
2680
2080
1790
1580
1380
5740
4860
4050
3010
2340
2000
1780
1550
6270
5310
4420
3280
2550
2180
1950
1690
7270
6150
5160
3820
2940
2530
2270
1970
5790
4660
3840
2850
2310
1950
1590
1180
920
800
700
0
7140
5760
4740
3490
2830
2400
1960
1450
1150
990
860
760
8740
7060
5820
4290
3460
2940
2400
1780
1420
1210
1060
930
7150
5260
4260
3600
2950
2190
1740
1480
1300
1140
8670
6340
5130
4330
3570
2650
2100
1780
1570
1370
7710
6210
5250
4330
3220
2530
2160
1910
1670
8740
7050
5950
4930
3660
2880
2450
2170
1890
8010
6780
5620
4180
3270
2790
2480
2160
8980
7600
6330
4710
3660
3120
2780
2420
9790
8290
6910
5140
3970
3410
3040
2640
9610
8050
5980
4600
3950
3540
3070
1620
1150
850
580
450
360
294
2140
1530
1140
780
600
480
390
5800
3960
2890
2140
1630
1320
1090
790
630
540
450
0
0
0
0
0
8620
6150
4570
3130
2410
1950
1600
1180
960
810
660
500
0
0
0
0
2020
1440
1080
730
570
450
370
2680
1900
1420
970
750
600
490
7170
4890
3570
2650
2020
1650
1360
990
810
660
550
420
0
0
0
0
2490
1770
1320
900
690
550
460
3280
2340
1750
1200
910
750
610
8800
6000
4360
3250
2500
2020
1680
1230
990
840
690
520
400
0
0
0
7650
5700
3900
3000
2430
1990
1470
1200
1000
810
610
470
0
0
0
7150
4890
3780
3040
2500
1860
1500
1270
1030
780
600
0
0
0
8910
6090
4710
3790
3120
2310
1870
1590
1290
960
740
650
0
0
500
Lengths in BOLD only meet the US National Electrical Code ampacity requirements for individual conductors in free air
or water. Lengths NOT in bold meet NEC ampacity requirements for either individual conductors or jacketed cable. See
page 11 for additional details.
18
!00,)#!4)/.
4HREE 0HASE -OTORS
Table 19 Three-Phase 75 °C Cable, 60 Hz (Service Entrance to Motor) Maximum Length in Feet
MOTOR RATING
VOLTS
200 V
60 Hz
ThreePhase
3 - Lead
230 V
60 Hz
ThreePhase
3 - Lead
380 V
60 Hz
ThreePhase
3 - Lead
75 °C INSULATION - AWG COPPER WIRE SIZE
HP
KW
14
12
10
8
6
1/2
0.37
710
1140
1800
2840
4420
3/4
0.55
510
810
1280
2030
3160
690
1080
1710
4
3
75 °C
MCM COPPER WIRE SIZE
2
1
0
00
000
0000
250
300
350
400
500
1
0.75
430
2670
4140
5140
1.5
1.1
310
500
790
1260
1960
3050
3780
2
1.5
240
390
610
970
1520
2360
2940
3610
4430
5420
3
2.2
180
290
470
740
1160
1810
2250
2760
3390
4130
5
3.7
110
170
280
440
690
1080
1350
1660
2040
2490
3050
3670
4440
5030
7.5
5.5
0
0
200
310
490
770
960
1180
1450
1770
2170
2600
3150
3560
10
7.5
0
0
150
230
370
570
720
880
1090
1330
1640
1970
2390
2720
3100
3480
3800
4420
15
11
0
0
0
160
250
390
490
600
740
910
1110
1340
1630
1850
2100
2350
2570
2980
20
15
0
0
0
0
190
300
380
460
570
700
860
1050
1270
1440
1650
1850
2020
2360
25
18.5
0
0
0
0
0
240
300
370
460
570
700
840
1030
1170
1330
1500
1640
1900
30
22
0
0
0
0
0
200
250
310
380
470
580
700
850
970
1110
1250
1360
1590
1/2
0.37
930
1490
2350
3700
5760
8910
3/4
0.55
670
1080
1700
2580
4190
6490
8060
9860
1
0.75
560
910
1430
2260
3520
5460
6780
8290
1.5
1.1
420
670
1060
1670
2610
4050
5030
6160
7530
9170
2
1.5
320
510
810
1280
2010
3130
3890
4770
5860
7170
8780
2.2
240
390
620
990
1540
2400
2980
3660
4480
5470
6690
8020
9680
230
370
590
920
1430
1790
2190
2690
3290
4030
4850
3
5
3.7
140
5870
6650
7560
8460
9220
7.5
5.5
0
160
260
420
650
1020
1270
1560
1920
2340
2870
3440
4160
4710
5340
5970
6500
7510
10
7.5
0
0
190
310
490
760
950
1170
1440
1760
2160
2610
3160
3590
4100
4600
5020
5840
15
11
0
0
0
210
330
520
650
800
980
1200
1470
1780
2150
2440
2780
3110
3400
3940
20
15
0
0
0
160
250
400
500
610
760
930
1140
1380
1680
1910
2180
2450
2680
3120
25
18.5
0
0
0
0
200
320
400
500
610
750
920
1120
1360
1540
1760
1980
2160
2520
30
22
0
0
0
0
0
260
330
410
510
620
760
930
1130
1280
1470
1650
1800
2110
1/2
0.37
2690
4290
6730
3/4
0.55
2000
3190
5010
7860
1
0.75
1620
2580
4060
6390
9980
1.5
1.1
1230
1970
3100
4890
7630
2
1.5
870
1390
2180
3450
5400
8380
3
2.2
680
1090
1710
2690
4200
6500
8020
9830
5
3.7
400
640
1010
1590
2490
3870
4780
5870
7230
8830
7.5
5.5
270
440
690
1090
1710
2640
3260
4000
4930
6010
7290
8780
10
7.5
200
320
510
800
1250
1930
2380
2910
3570
4330
5230
6260
7390
8280
9340
11
0
0
370
590
920
1430
1770
2170
2690
3290
4000
4840
5770
6520
7430
8250
8990
15
0
0
280
440
700
1090
1350
1670
2060
2530
3090
3760
4500
5110
2840
6510
7120
8190
25
18.5
0
0
0
360
570
880
1100
1350
1670
2050
2510
3040
3640
4130
4720
5250
5740
6590
30
22
0
0
0
290
470
730
910
1120
1380
1700
2080
2520
3020
3430
3920
4360
4770
5490
40
30
0
0
0
0
0
530
660
820
1010
1240
1520
1840
2200
2500
2850
3170
3470
3990
50
37
0
0
0
0
0
440
540
660
820
1000
1220
1480
1770
2010
2290
2550
2780
3190
60
45
0
0
0
0
0
370
460
560
690
850
1030
1250
1500
1700
1940
2150
2350
2700
75
55
0
0
0
0
0
0
0
460
570
700
860
1050
1270
1440
1660
1850
2030
2350
100
75
0
0
0
0
0
0
0
0
420
510
630
760
910
1030
1180
1310
1430
1650
125
93
0
0
0
0
0
0
0
0
0
0
510
620
740
840
950
1060
1160
1330
150
110
0
0
0
0
0
0
0
0
0
0
0
520
620
700
790
880
960
1090
175
130
0
0
0
0
0
0
0
0
0
0
0
0
560
650
750
840
920
1070
200
150
0
0
0
0
0
0
0
0
0
0
0
0
0
550
630
700
760
880
15
20
Lengths in BOLD only meet the US National Electrical Code ampacity requirements for individual conductors in free air
or water. Lengths NOT in bold meet NEC ampacity requirements for either individual conductors or jacketed cable. See
page 11 for additional details.
19
Continued on next page
!00,)#!4)/.
4HREE 0HASE -OTORS
75 °C
Table 20 Three-Phase 75 °C Cable (Continued)
MOTOR RATING
VOLTS
460 V
60 Hz
ThreePhase
3 - Lead
KW
14
12
10
1/2
0.37
3770
6020
9460
3/4
0.55
2730
4350
6850
3670
8
6
4
3
2
1
MCM COPPER WIRE SIZE
0
00
000
0000
250
300
350
400
500
1
0.75
2300
5770
9070
1.5
1.1
1700
2710
4270
6730
2
1.5
1300
2070
3270
5150
8050
3
2.2
1000
1600
2520
3970
6200
5
3.7
590
950
1500
2360
3700
5750
7.5
5.5
420
680
1070
1690
2640
4100
5100
6260
7680
10
7.5
310
500
790
1250
1960
3050
3800
4680
5750
15
11
0
340
540
850
1340
2090
2600
3200
3930
4810
5900
7110
20
15
0
0
410
650
1030
1610
2000
2470
3040
3730
4580
5530
25
18.5
0
0
330
530
830
1300
1620
1990
2450
3010
3700
4470
5430
30
22
0
0
270
430
680
1070
1330
1640
2030
2490
3060
3700
4500
5130
5860
40
30
0
0
0
320
500
790
980
1210
1490
1830
2250
2710
3290
3730
4250
50
37
0
0
0
0
410
640
800
980
1210
1480
1810
2190
2650
3010
3420
3830
4180
4850
60
45
0
0
0
0
0
540
670
830
1020
1250
1540
1850
2240
2540
2890
3240
3540
4100
75
55
0
0
0
0
0
440
550
680
840
1030
1260
1520
1850
2100
2400
2700
2950
3440
100
75
0
0
0
0
0
0
0
500
620
760
940
1130
1380
1560
1790
2010
2190
2550
93
0
0
0
0
0
0
0
0
0
600
740
890
1000
1220
1390
1560
1700
1960
110
0
0
0
0
0
0
0
0
0
0
630
760
920
1050
1190
1340
1460
1690
175
130
0
0
0
0
0
0
0
0
0
0
0
670
810
930
1060
1190
1300
1510
200
150
0
0
0
0
0
0
0
0
0
0
0
590
710
810
920
1030
1130
1310
1/2
0.37
5900
9410
3/4
0.55
4270
6810
1
0.75
3630
5800
9120
1.5
1.1
2620
4180
6580
2
1.5
2030
3250
5110
8060
3
2.2
1580
2530
3980
6270
5
3.7
920
1480
2330
3680
5750
7.5
5.5
660
1060
1680
2650
4150
10
7.5
490
780
1240
1950
3060
4770
5940
15
11
330
530
850
1340
2090
3260
4060
20
15
0
410
650
1030
1610
2520
3140
3860
4760
5830
25
18.5
0
0
520
830
1300
2030
2530
3110
3840
4710
30
22
0
0
430
680
1070
1670
2080
2560
3160
3880
4770
5780
7030
8000
30
0
0
0
500
790
1240
1540
1900
2330
2860
3510
4230
5140
5830
37
0
0
0
410
640
1000
1250
1540
1890
2310
2840
3420
4140
4700
5340
5990
6530
7580
60
45
0
0
0
0
540
850
1060
1300
1600
1960
2400
2890
3500
3970
4520
5070
5530
6410
75
55
0
0
0
0
0
690
860
1060
1310
1600
1970
2380
2890
3290
3750
5220
4610
5370
100
75
0
0
0
0
0
0
640
790
970
1190
1460
1770
2150
2440
2790
3140
3430
3990
125
93
0
0
0
0
0
0
0
630
770
950
1160
1400
1690
1920
2180
2440
2650
3070
150
110
0
0
0
0
0
0
0
0
660
800
990
1190
1440
1630
1860
2080
2270
2640
175
130
0
0
0
0
0
0
0
0
0
700
870
1050
1270
1450
1650
1860
2030
2360
200
150
0
0
0
0
0
0
0
0
0
0
760
920
1110
1260
1440
1620
1760
2050
125
150
575 V
60 Hz
ThreePhase
3 - Lead
75 °C INSULATION - AWG COPPER WIRE SIZE
HP
40
50
7050
Lengths in BOLD only meet the US National Electrical Code ampacity requirements for individual conductors in free air
or water. Lengths NOT in bold meet NEC ampacity requirements for either individual conductors or jacketed cable. See
page 11 for additional details.
Continued on next page
20
!00,)#!4)/.
4HREE 0HASE -OTORS
75 °C
Table 21 Three-Phase 75 °C Cable (Continued)
MOTOR RATING
VOLTS
HP
KW
5
3.7
200 V
7.5
5.5
60 Hz
10
7.5
Three15
11
Phase
20
15
6 - Lead
25
18.5
Y-D
30
22
5
3.7
230 V
7.5
5.5
60 Hz
10
7.5
Three15
11
Phase
20
15
6 - Lead
25
18.5
Y-D
30
22
5
3.7
7.5
5.5
10
7.5
15
11
20
15
25
18.5
380 V
30
22
60 Hz
40
30
ThreePhase
50
37
6 - Lead
60
45
Y-D
75
55
100
75
125
93
150
110
175
130
200
150
5
3.7
7.5
5.5
10
7.5
15
11
20
15
25
18.5
460 V
30
22
60 Hz
40
30
ThreePhase
50
37
6 - Lead
60
45
Y-D
75
55
100
75
125
93
150
110
175
130
200
150
5
3.7
7.5
5.5
10
7.5
15
11
20
15
25
18.5
575 V
30
22
60 Hz
40
30
ThreePhase
50
37
6 - Lead
60
45
Y-D
75
55
100
75
125
93
150
110
175
130
200
150
14
12
10
8
160
110
80
0
0
0
0
210
150
110
0
0
0
0
600
400
300
210
160
0
0
0
0
0
0
0
0
0
0
0
880
630
460
310
230
190
0
0
0
0
0
0
0
0
0
0
1380
990
730
490
370
300
240
0
0
0
0
0
0
0
0
0
250
180
130
0
0
0
0
340
240
180
130
0
0
0
960
660
480
340
260
210
0
0
0
0
0
0
0
0
0
0
1420
1020
750
510
380
310
250
0
0
0
0
0
0
0
0
0
2220
1590
1170
790
610
490
400
300
0
0
0
0
0
0
0
0
420
300
210
140
120
0
0
550
390
280
190
140
120
0
1510
1030
760
550
410
330
270
210
0
0
0
0
0
0
0
0
2250
1600
1180
810
610
490
410
300
250
0
0
0
0
0
0
0
3490
2520
1860
1270
970
780
645
480
380
330
0
0
0
0
0
0
660
460
340
240
170
140
120
880
630
460
310
230
190
150
2380
1630
1200
880
660
540
430
320
250
0
0
0
0
0
0
0
3540
2530
1870
1270
970
790
640
480
370
320
0
0
0
0
0
0
5520
3970
2920
2010
1540
1240
1020
750
590
500
420
0
0
0
0
0
75 °C INSULATION - AWG COPPER WIRE SIZE
6
4
3
2
1
1030
730
550
370
280
220
180
1380
970
730
490
370
300
240
3730
2560
1870
1380
1050
850
700
510
400
340
290
0
0
0
0
0
5550
3960
2940
2010
1540
1240
1020
750
590
500
420
310
0
0
0
0
8620
6220
4590
3130
2410
1950
1600
1180
960
790
660
400
0
0
0
0
0
00
000
0000
250
3060
2170
1630
1110
850
690
570
4030
2880
2160
1470
1140
910
760
3730
2650
1990
1360
1050
850
700
4930
3510
2640
1800
1390
1120
930
4570
3250
2460
1660
1290
1050
870
6040
4300
3240
2200
1710
1380
1140
5500
3900
2950
2010
1570
1260
1050
7270
5160
3910
2670
2070
1680
1390
6660
4720
3580
2440
1900
1540
1270
8800
6240
4740
3220
2520
2040
1690
7540
5340
4080
2770
2160
1750
1450
9970
7060
5380
3660
2860
2310
1920
7390
5350
4030
3090
2500
2070
1510
1230
1030
855
640
490
420
360
0
9010
6490
4930
3790
3070
2550
1860
1500
1270
1050
760
600
510
440
410
7840
6000
4630
3760
3120
2280
1830
1540
1290
940
730
620
540
480
9390
7260
5640
4560
3780
2760
2220
1870
1570
1140
930
750
660
580
8650
6750
5460
4530
3300
2650
2250
1900
1360
1110
930
780
690
9390
7020
4800
3700
2980
2460
1810
1470
1240
1020
760
590
510
450
0
8620
5890
4560
3670
3040
2230
1810
1530
1260
930
730
630
550
480
7210
5590
4510
3730
2740
2220
1870
1540
1140
880
770
680
590
8850
6870
5550
4590
3370
2710
2310
1890
1410
1110
950
830
730
8290
6700
5550
4060
3280
2770
2280
1690
1330
1140
1000
880
5790
4660
3840
2850
2310
1950
1590
1180
920
800
700
610
7140
5760
4740
3490
2830
2400
1960
1450
1150
990
860
760
8740
7060
5820
4290
3460
2940
2400
1780
1420
1210
1060
930
7150
5260
4260
3600
2950
2190
1740
1480
1300
1140
8670
6340
5130
4330
3570
2650
2100
1780
1570
1370
1620
1150
850
580
450
360
294
2140
1530
1140
780
600
480
390
5800
3960
2890
2140
1630
1320
1090
790
630
540
450
340
0
0
0
0
8620
6150
4570
3130
2410
1950
1600
1180
960
810
660
500
390
0
0
0
2020
1440
1080
730
570
450
370
2680
1900
1420
970
750
600
490
7170
4890
3570
2650
2020
1650
1360
990
810
660
550
420
340
0
0
0
2490
1770
1320
900
690
550
460
3280
2340
1750
1200
910
750
610
8800
6000
4360
3250
2500
2020
1680
1230
990
840
690
520
400
350
0
0
7650
5700
3900
3000
2430
1990
1470
1200
1000
810
610
470
420
0
0
7150
4890
3780
3040
2500
1860
1500
1270
1030
780
600
520
0
0
8910
6090
4710
3790
3120
2310
1870
1590
1290
960
740
650
570
500
MCM COPPER WIRE SIZE
300
350
400
500
4650
3150
2470
1990
1660
5220
3520
2770
2250
1870
5700
3850
3030
2460
2040
6630
4470
3540
2850
2380
8010
6150
4170
3270
2640
2200
8950
6900
4660
3670
2970
2470
9750
7530
5100
4020
3240
2700
8760
5910
4680
3780
3160
9780
7660
6190
5140
3750
3010
2550
2160
1540
1260
1050
970
790
4260
7080
5880
4270
3430
2910
2490
1770
1420
1180
1120
940
9760
7870
6540
4750
3820
3220
2770
1960
1590
1320
1260
1050
8610
7150
5200
4170
3520
3040
2140
1740
1440
1380
1140
9880
8230
5980
4780
4050
3520
2470
1990
1630
1600
1320
8140
6750
4930
3970
3360
2770
2070
1500
1380
1220
1070
7690
5590
4510
3810
3150
2340
1830
1570
1390
1210
8790
6370
5130
4330
3600
2680
2080
1790
1580
1380
5740
4860
4050
3010
2340
2000
1780
1550
6270
5310
4420
3280
2550
2180
1950
1690
7270
6150
5160
3820
2940
2530
2270
1970
7710
6210
5250
4330
3220
2530
2160
1910
1670
8740
7050
5950
4930
3660
2880
2450
2170
1890
8010
6780
5620
4180
3270
2790
2480
2160
8980
7600
6330
4710
3660
3120
2780
2420
9790
8290
6910
5140
3970
3410
3040
2640
9610
8050
5980
4600
3950
3540
3070
Lengths in BOLD only meet the US National Electrical Code ampacity requirements for individual conductors in free air
or water. Lengths NOT in bold meet NEC ampacity requirements for either individual conductors or jacketed cable. See
page 11 for additional details.
21
!00,)#!4)/.
4HREE 0HASE -OTORS
Table 22 Three-Phase Motor Specifications (60 Hz) 3450 rpm
TYPE
4"
MOTOR
MODEL
PREFIX
MAXIMUM
LOAD
VOLTS
HZ
S.F.
AMPS
WATTS
AMPS
WATTS
LINE TO LINE
RESISTANCE
OHMS
S.F.
F.L.
LOCKED
ROTOR
AMPS
234501
200
60
1.6
2.8
585
3.4
860
6.6-8.4
70
64
17.5
N
234511
230
60
1.6
2.4
585
2.9
860
9.5-10.9
70
64
15.2
N
380
60
1.6
1.4
585
2.1
860
23.2-28.6
70
64
9.2
N
234521
460
60
1.6
1.2
585
1.5
860
38.4-44.1
70
64
7.6
N
234531
575
60
1.6
1.0
585
1.2
860
58.0-71.0
70
64
6.1
N
234502
200
60
1.5
3.6
810
4.4
1150
4.6-5.9
73
69
24.6
N
234512
230
60
1.5
3.1
810
3.8
1150
6.8-7.8
73
69
21.4
N
380
60
1.5
1.9
810
2.5
1150
16.6-20.3
73
69
13
N
234522
460
60
1.5
1.6
810
1.9
1150
27.2-30.9
73
69
10.7
N
234532
575
60
1.5
1.3
810
1.6
1150
41.5-50.7
73
69
8.6
N
234503
200
60
1.4
4.5
1070
5.4
1440
3.8-4.5
72
70
30.9
M
234541
234542
RATING
HP
1/2
3/4
KW
0.37
0.55
234513
234543
1
0.75
FULL LOAD
EFFICIENCY %
KVA
CODE
230
60
1.4
3.9
1070
4.7
1440
4.9-5.6
72
70
26.9
M
380
60
1.4
2.3
1070
2.8
1440
12.2-14.9
72
70
16.3
M
234523
460
60
1.4
2
1070
2.4
1440
19.9-23.0
72
70
13.5
M
234533
575
60
1.4
1.6
1070
1.9
1440
30.1-36.7
72
70
10.8
M
234504
200
60
1.3
5.8
1460
6.8
1890
2.5-3.0
76
76
38.2
K
234514
230
60
1.3
5
1460
5.9
1890
3.2-4.0
76
76
33.2
K
234544
1.5
1.1
234524
380
60
1.3
3
1460
3.6
1890
8.5-10.4
76
76
20.1
K
460
60
1.3
2.5
1460
3.1
1890
13.0-16.0
76
76
16.6
K
234534
575
60
1.3
2
1460
2.4
1890
20.3-25.0
76
76
13.3
K
234305
200
60
1.25
7.7
1960
9.3
2430
1.8-2.4
76
76
50.3
K
234315
234345
2
1.5
230
60
1.25
6.7
1960
8.1
2430
2.3-3.0
76
76
45.0
K
380
60
1.25
4.1
1960
4.9
2430
6.6-8.2
76
76
26.6
K
234325
460
60
1.25
3.4
1960
4.1
2430
9.2-12.0
76
76
22.5
K
234335
575
60
1.25
2.7
1960
3.2
2430
14.6-18.7
76
76
17.8
K
234306
200
60
1.15
10.9
2920
12.5
3360
1.3-1.7
77
77
69.5
K
234316
230
60
1.15
9.5
2920
10.9
3360
1.8-2.2
77
77
60.3
K
380
60
1.15
5.8
2920
6.6
3360
4.7-6.0
77
77
37.5
K
460
60
1.15
4.8
2920
5.5
3360
7.2-8.8
77
77
31.0
K
234346
3
2.2
234326
234336
575
60
1.15
3.8
2920
4.4
3360
11.4-13.9
77
77
25.1
K
234307
200
60
1.15
18.3
4800
20.5
5500
.68-.83
78
78
116
K
234317
234347
5
3.7
230
60
1.15
15.9
4800
17.8
5500
.91-1.1
78
78
102
K
380
60
1.15
9.6
4800
10.8
5500
2.6-3.2
78
78
60.2
K
234327
460
60
1.15
8.0
4800
8.9
5500
3.6-4.4
78
78
53.7
K
234337
575
60
1.15
6.4
4800
7.1
5500
5.6-6.9
78
78
41.8
K
234308
200
60
1.15
26.5
7150
30.5
8200
.43-.53
78
78
177
K
234318
230
60
1.15
23.0
7150
26.4
8200
.60-.73
78
78
152
K
234348
7.5
5.5
234328
380
60
1.15
13.9
7150
16.0
8200
1.6-2.0
78
78
92.7
K
460
60
1.15
11.5
7150
13.2
8200
2.3-2.8
78
78
83.8
K
234338
575
60
1.15
9.2
7150
10.6
8200
3.6-4.5
78
78
64.6
K
234549
380
60
1.15
19.3
10000
21.0
11400
1.2-1.6
75
75
140
L
460
60
1.15
15.9
10000
17.3
11400
1.8-2.3
75
75
116.0
L
575
60
1.15
12.5
10000
13.6
11400
2.8-3.5
75
75
92.8
L
234595
234598
10
7.5
22
!00,)#!4)/.
4HREE 0HASE -OTORS
Table 23 Three-Phase Motor Fuse Sizing
TYPE
4"
MOTOR
MODEL
PREFIX
CIRCUIT BREAKERS OR FUSE AMPS
(MAXIMUM PER NEC)
(TYPICAL SUBMERSIBLE)
VOLTS
STANDARD
FUSE
DUAL ELEMENT TIME
DELAY FUSE
CIRCUIT
BREAKER
STANDARD
FUSE
DUAL ELEMENT TIME
DELAY FUSE
CIRCUIT
BREAKER
234501
200
234511
230
10
5
8
10
4
15
8
4.5
6
8
4
15
380
5
2.5
4
5
2
15
234521
460
4
2.25
3
4
2
15
234531
575
3
1.8
3
3
1.4
15
234502
200
15
7
10
12
5
15
234512
230
10
5.6
8
10
5
15
380
6
3.5
5
6
3
15
234522
460
5
2.8
4
5
3
15
234532
575
4
2.5
4
4
1.8
15
234503
200
15
8
15
15
6
15
234513
230
15
7
10
12
6
15
380
8
4.5
8
8
4
15
234523
460
6
3.5
5
6
3
15
234533
575
5
2.8
4
5
2.5
15
234504
200
20
12
15
20
8
15
234514
230
15
9
15
15
8
15
380
10
5.6
8
10
4
15
234524
460
8
4.5
8
8
4
15
234534
575
6
3.5
5
6
3
15
234305
200
25
15
20
25
11
20
234315
230
25
12
20
25
10
20
380
15
8
15
15
6
15
234325
460
15
6
10
11
5
15
234335
575
10
5
8
10
4
15
234306
200
35
20
30
35
15
30
234316
230
30
17.5
25
30
12
25
380
20
12
15
20
8
15
234326
460
15
9
15
15
6
15
234336
575
15
7
10
11
5
15
234307
200
60
35
50
60
25
50
234317
230
50
30
40
45
20
40
380
30
17.5
25
30
12
25
234327
460
25
15
20
25
10
20
234337
575
20
12
20
20
8
20
234308
200
90
50
70
80
35
70
234318
230
80
45
60
70
30
60
380
45
25
40
40
20
40
234328
460
40
25
30
35
15
30
234338
575
30
17.5
25
30
12
25
234349
380
70
40
60
60
25
60
234329
460
60
30
45
50
25
45
234339
575
45
25
35
40
20
35
380
70
35
60
60
25
60
234595
460
60
30
45
50
25
45
234598
575
45
25
35
40
20
35
234541
234542
234543
234544
234345
234346
234347
234348
234549
23
CIRCUIT BREAKERS OR FUSE AMPS
RATING
HP
1/2
3/4
1
1.5
2
3
5
7.5
10
KW
0.37
0.55
0.75
1.1
1.5
2.2
3.7
5.5
7.5
!00,)#!4)/.
4HREE 0HASE -OTORS
Table 24 Three-Phase Motor Specifications (60 Hz) 3450 rpm
TYPE
6"
STD.
MOTOR
MODEL
PREFIX
MAXIMUM
LOAD
VOLTS
HZ
S.F.
AMPS
WATTS
AMPS
WATTS
LINE TO LINE
RESISTANCE
OHMS
236650
200
60
1.15
17.5
4700
20.0
5400
.77-.93
79
79
99
H
236600
230
60
1.15
15
4700
17.6
5400
1.0-1.2
79
79
86
H
236660
RATING
HP
5
KW
3.7
236610
FULL LOAD
EFFICIENCY %
S.F.
F.L.
LOCKED
ROTOR
AMPS
KVA
CODE
380
60
1.15
9.1
4700
10.7
5400
2.6-3.2
79
79
52
H
460
60
1.15
7.5
4700
8.8
5400
3.9-4.8
79
79
43
H
236620
575
60
1.15
6
4700
7.1
5400
6.3-7.7
79
79
34
H
236651
200
60
1.15
25.1
7000
28.3
8000
.43-.53
80
80
150
H
236601
236661
7.5
5.5
230
60
1.15
21.8
7000
24.6
8000
.64-.78
80
80
130
H
380
60
1.15
13.4
7000
15
8000
1.6-2.1
80
80
79
H
236611
460
60
1.15
10.9
7000
12.3
8000
2.4-2.9
80
80
65
H
236621
575
60
1.15
8.7
7000
9.8
8000
3.7-4.6
80
80
52
H
236652
200
60
1.15
32.7
9400
37
10800
.37-.45
79
79
198
H
236602
230
60
1.15
28.4
9400
32.2
10800
.47-.57
79
79
172
H
236662
10
7.5
236612
380
60
1.15
17.6
9400
19.6
10800
1.2-1.5
79
79
104
H
460
60
1.15
14.2
9400
16.1
10800
1.9-2.4
79
79
86
H
236622
575
60
1.15
11.4
9400
12.9
10800
3.0-3.7
79
79
69
H
236653
200
60
1.15
47.8
13700
54.4
15800
.24-.29
81
81
306
H
236603
236663
15
11
230
60
1.15
41.6
13700
47.4
15800
.28-.35
81
81
266
H
380
60
1.15
25.8
13700
28.9
15800
.77-.95
81
81
161
H
236613
460
60
1.15
20.8
13700
23.7
15800
1.1-1.4
81
81
133
H
236623
575
60
1.15
16.6
13700
19
15800
1.8-2.3
81
81
106
H
236654
200
60
1.15
61.9
18100
69.7
20900
.16-.20
82
82
416
J
236604
230
60
1.15
53.8
18100
60.6
20900
.22-.26
82
82
362
J
236664
20
15
236614
380
60
1.15
33
18100
37.3
20900
.55-.68
82
82
219
J
460
60
1.15
26.9
18100
30.3
20900
.8-1.0
82
82
181
J
236624
575
60
1.15
21.5
18100
24.2
20900
1.3-1.6
82
82
145
J
236655
200
60
1.15
77.1
22500
86.3
25700
.12-.15
83
83
552
J
J
236605
236665
25
18.5
236615
230
60
1.15
67
22500
75
25700
.15-.19
83
83
480
380
60
1.15
41
22500
46
25700
.46-.56
83
83
291
J
460
60
1.15
33.5
22500
37.5
25700
.63-.77
83
83
240
J
236625
575
60
1.15
26.8
22500
30
25700
1.0-1.3
83
83
192
J
236656
200
60
1.15
90.9
26900
104
31100
.09-.11
83
83
653
J
236606
236666
30
22
230
60
1.15
79
26900
90.4
31100
.14-.17
83
83
568
J
380
60
1.15
48.8
26900
55.4
31100
.35-.43
83
83
317
J
236616
460
60
1.15
39.5
26900
45.2
31100
.52-.64
83
83
284
J
236626
575
60
1.15
31.6
26900
36.2
31100
.78-.95
83
83
227
J
236667
236617
40
30
380
60
1.15
66.5
35600
74.6
42400
.26-.33
83
83
481
J
460
60
1.15
54.9
35600
61.6
42400
.34-.42
83
83
397
J
236627
575
60
1.15
42.8
35600
49.6
42400
.52-.64
83
83
318
H
236668
380
60
1.15
83.5
45100
95
52200
.21-.25
82
83
501
H
236618
460
60
1.15
67.7
45100
77
52200
.25-.32
82
83
414
H
236628
575
60
1.15
54.2
45100
61.6
52200
.40-.49
82
83
331
H
276668
50
37
276618
380
60
1.15
82.4
45100
94.5
52200
.21 - .25
82
83
501
H
460
60
1.15
68.1
45100
78.1
52200
.25 - .32
82
83
414
H
276628
575
60
1.15
54.5
45100
62.5
52200
.40 - .49
82
83
331
H
236669
380
60
1.15
98.7
53500
111
61700
.15-.18
84
84
627
H
236619
460
60
1.15
80.5
53500
91
61700
.22-.27
84
84
518
H
236629
575
60
1.15
64.4
53500
72.8
61700
.35-.39
84
84
414
H
276669
60
45
380
60
1.15
98.1
53500
111.8
61700
.15 - .18
84
84
627
H
276619
460
60
1.15
81.0
53500
92.3
61700
.22 - .27
84
84
518
H
276629
575
60
1.15
64.8
53500
73.9
61700
.35 - .39
84
84
414
H
Model numbers above are for three-lead motors. Six-lead motors with different model numbers have the same running
performance, but when Wye connected for starting have locked rotor amps 33% of the values shown. Six-lead individual
phase resistance = table X 1.5.
24
!00,)#!4)/.
4HREE 0HASE -OTORS
Table 25 6” Three-Phase Motor Specifications (60 Hz) 3450 rpm
TYPE
6"
HITEMP
90 °C
MOTOR
MODEL
PREFIX
MAXIMUM
LOAD
VOLTS
HZ
S.F.
AMPS
WATTS
AMPS
WATTS
LINE TO LINE
RESISTANCE
OHMS
276650
200
60
1.15
17.2
5200
19.8
5800
.53 - .65
73
72
124
K
276600
230
60
1.15
15.0
5200
17.2
5800
.68 - .84
73
72
108
K
276660
RATING
HP
5
KW
3.7
276610
FULL LOAD
EFFICIENCY %
S.F.
F.L.
LOCKED
ROTOR
AMPS
KVA
CODE
380
60
1.15
9.1
5200
10.4
5800
2.0 - 2.4
73
72
66.0
K
460
60
1.15
7.5
5200
8.6
5800
2.8 - 3.4
73
72
54.0
K
276620
575
60
1.15
6.0
5200
6.9
5800
4.7 - 5.7
73
72
43.0
K
276651
200
60
1.15
24.8
7400
28.3
8400
.30 - .37
77
76
193
K
276601
276661
7.5
5.5
230
60
1.15
21.6
7400
24.6
8400
.41 - .50
77
76
168
K
380
60
1.15
13.1
7400
14.9
8400
1.1 - 1.4
77
76
102
K
276611
460
60
1.15
10.8
7400
12.3
8400
1.7 - 2.0
77
76
84.0
K
276621
575
60
1.15
8.6
7400
9.9
8400
2.6 - 3.2
77
76
67.0
K
276652
200
60
1.15
32.0
9400
36.3
10700
.21 - .26
80
79
274
L
276602
230
60
1.15
27.8
9400
31.6
10700
.28 - .35
80
79
238
L
276662
10
7.5
276612
380
60
1.15
16.8
9400
19.2
10700
.80 - .98
80
79
144
L
460
60
1.15
13.9
9400
15.8
10700
1.2 - 1.4
80
79
119
L
276622
575
60
1.15
11.1
9400
12.7
10700
1.8 - 2.2
80
79
95.0
L
276653
200
60
1.15
48.5
14000
54.5
15900
.15 - .19
81
80
407
L
276603
276663
15
11
230
60
1.15
42.2
14000
47.4
15900
.19 - .24
81
80
354
L
380
60
1.15
25.5
14000
28.7
15900
.52 - .65
81
80
214
L
276613
460
60
1.15
21.1
14000
23.7
15900
.78 - .96
81
80
177
L
276623
575
60
1.15
16.9
14000
19.0
15900
1.2 - 1.4
81
80
142
L
276654
200
60
1.15
64.9
18600
73.6
21300
.10 - .12
80
80
481
K
276604
230
60
1.15
56.4
18600
64.0
21300
.14 - .18
80
80
418
K
276664
20
15
276614
380
60
1.15
34.1
18600
38.8
21300
.41 - .51
80
80
253
K
460
60
1.15
28.2
18600
32.0
21300
.58 - .72
80
80
209
K
K
276624
575
60
1.15
22.6
18600
25.6
21300
.93 - 1.15
80
80
167
276655
200
60
1.15
80.0
22600
90.6
25800
.09 - .11
83
82
665
L
276605
230
60
1.15
69.6
22600
78.8
25800
.11 - .14
83
82
578
L
380
60
1.15
42.1
22600
47.7
25800
.27 - .34
83
82
350
L
460
60
1.15
34.8
22600
39.4
25800
.41 - .51
83
82
289
L
276665
25
18.5
276615
276625
575
60
1.15
27.8
22600
31.6
25800
.70 - .86
83
82
231
L
276656
200
60
1.15
95.0
28000
108.6
31900
.07 - .09
81
80
736
K
276606
276666
30
22
230
60
1.15
82.6
28000
94.4
31900
.09 - .12
81
80
640
K
380
60
1.15
50.0
28000
57.2
31900
.23 - .29
81
80
387
K
276616
460
60
1.15
41.3
28000
47.2
31900
.34 - .42
81
80
320
K
276626
575
60
1.15
33.0
28000
37.8
31900
.52 - .65
81
80
256
K
276667
276617
276627
40
30
380
60
1.15
67.2
35900
76.0
42400
.18 - .23
84
83
545
L
460
60
1.15
55.4
35900
62.8
42400
.23 - .29
84
83
450
L
575
60
1.15
45.2
35900
50.2
42400
.34 - .43
84
83
360
L
Model numbers above are for three-lead motors. Six-lead motors with different model numbers have the same running
performance, but when Wye connected for starting have locked rotor amps 33% of the values shown. Six-lead individual
phase resistance = table X 1.5.
25
!00,)#!4)/.
4HREE 0HASE -OTORS
Table 26 Three-Phase Motor Fuse Sizing
TYPE
6"
STD.
& HITEMP
MOTOR
MODEL
PREFIX
236650
236600
236660
236610
236620
236651
236601
236661
236611
236621
236652
236602
276650
276600
276660
276610
276620
276651
276601
276661
276611
276621
276652
276602
236662
236612
236622
236653
236603
236663
236613
236623
236654
236604
236664
236614
236624
236655
236605
236665
236615
236625
236656
236606
236666
236616
236626
236667
236617
236627
236668
236618
236628
236669
236619
236629
276662
276612
276622
276653
276603
276663
276613
276623
276654
276604
276664
276614
276624
276655
276605
276665
276615
276625
276656
276606
276666
276616
276626
276667
276617
276627
276668
276618
276628
276669
276619
276629
CIRCUIT BREAKERS OR FUSE AMPS
CIRCUIT BREAKERS OR FUSE AMPS
(MAXIMUM PER NEC)
(TYPICAL SUBMERSIBLE)
RATING
HP
KW
5
3.7
7.5
5.5
10
7.5
15
11
20
15
25
18.5
30
22
40
30
50
37
60
45
VOLTS
STANDARD
FUSE
DUAL ELEMENT TIME
DELAY FUSE
CIRCUIT
BREAKER
STANDARD
FUSE
DUAL ELEMENT TIME
DELAY FUSE
CIRCUIT
BREAKER
200
230
380
460
575
200
230
380
460
575
200
230
60
45
30
25
20
80
70
45
35
30
100
90
35
30
17.5
15
12
45
40
25
20
17.5
60
50
45
40
25
20
15
70
60
35
30
25
90
80
50
45
30
25
20
80
70
40
35
25
100
90
25
20
12
10
8
35
30
20
15
11
45
40
45
40
25
20
15
70
60
35
30
25
90
80
380
460
575
200
230
380
460
575
200
230
380
460
575
200
230
380
460
575
200
230
380
460
575
380
460
575
380
460
575
380
460
575
60
45
35
150
150
80
70
60
200
175
100
90
70
250
225
125
110
90
300
250
150
125
100
200
175
150
250
225
175
300
250
200
35
25
20
90
80
50
40
30
110
100
60
50
40
150
125
80
60
50
175
150
90
70
60
125
100
80
150
125
100
175
150
125
45
40
30
125
110
70
60
45
175
150
90
70
60
200
175
110
90
70
250
225
125
110
90
175
150
110
225
175
150
250
225
175
50
45
35
150
125
80
60
50
175
175
100
80
70
225
200
125
100
80
300
250
150
125
100
200
175
125
250
200
175
300
250
200
25
20
15
60
60
35
30
25
80
70
45
35
30
100
90
50
45
35
125
100
60
50
40
90
70
60
110
90
70
125
100
80
45
40
30
125
110
70
60
45
175
150
90
70
60
200
175
110
90
70
250
200
125
100
80
175
150
110
225
175
150
250
225
175
26
!00,)#!4)/.
4HREE 0HASE -OTORS
Table 27 Three-Phase Motor Specifications (60 Hz) 3525 rpm
TYPE
8"
STD.
MOTOR
MODEL
PREFIX
239660
239600
239610
239661
239601
239611
239662
239602
239612
239663
239603
239613
239664
239604
239614
239165
239105
239115
239166
239106
239116
239167
239107
239117
239168
239108
239118
HP
KW
40
30
50
37
60
45
75
55
100
75
125
93
150
110
175
130
200
150
MAXIMUM
LOAD
VOLTS
HZ
S.F.
AMPS
KILOWATTS
AMPS
KILOWATTS
LINE TO LINE
RESISTANCE
OHMS
380
460
575
380
460
575
380
460
575
380
460
575
380
460
575
380
460
575
380
460
575
380
460
575
380
460
575
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
1.15
1.15
1.15
1.15
1.15
1.15
1.15
1.15
1.15
1.15
1.15
1.15
1.15
1.15
1.15
1.15
1.15
1.15
1.15
1.15
1.15
1.15
1.15
1.15
1.15
1.15
1.15
64
53
42
79
64
51
92
76
61
114
94
76
153
126
101
202
167
134
235
194
155
265
219
175
298
246
197
35
35
35
43
43
43
52
52
52
64
64
64
85
85
85
109
109
109
128
128
128
150
150
150
169
169
169
72
60
48
88
73
59
104
86
69
130
107
86
172
142
114
228
188
151
266
219
176
302
249
200
342
282
226
40
40
40
49
49
49
60
60
60
73.5
73.5
73.5
97.5
97.5
97.5
125
125
125
146
146
146
173
173
173
194
194
194
.16-.20
.24-.30
.39-.49
.12-.16
.18-.22
.28-.34
.09-.11
.14-.17
.22-.28
.06-.09
.10-.13
.16-.21
.05-.06
.07-.09
.11-.13
.03-.04
.05-.07
.08-.11
.02-.03
.04-.05
.06-.08
.02-.04
.04-.05
.06-.08
.02-.03
.03-.05
.05-.07
RATING
FULL LOAD
EFFICIENCY
%
S.F.
86
86
86
87
87
87
88
88
88
88
88
88
89
89
89
87
87
87
88
88
88
88
88
88
88
88
88
F.L.
LOCKED
ROTOR
AMPS
KVA
CODE
86
86
86
87
87
87
87
87
87
88
88
88
89
89
89
86
86
86
87
87
87
88
88
88
88
88
88
479
396
317
656
542
434
797
658
526
1046
864
691
1466
1211
969
1596
1318
1054
1961
1620
1296
1991
1645
1316
2270
1875
1500
J
J
J
K
K
K
K
K
K
L
L
L
L
L
L
K
K
K
K
K
K
J
J
J
J
J
J
KVA
CODE
M
M
M
M
M
M
N
N
N
L
L
L
M
M
M
L
L
L
K
K
K
Table 27A 8” Three-Phase Motor Specifications (60 Hz) 3525 rpm
TYPE
8"
HITEMP
MOTOR
MODEL
PREFIX
279160
279100
279110
279161
279101
279111
279162
279102
279112
279163
279103
279113
279164
279104
279114
279165
279105
279115
279166
279106
279116
HP
KW
40
30
50
37
60
45
75
56
100
75
125
93
150
110
MAXIMUM
LOAD
VOLTS
HZ
S.F.
AMPS
KILOWATTS
AMPS
KILOWATTS
LINE TO LINE
RESISTANCE
OHMS
380
460
575
380
460
575
380
460
575
380
460
575
380
460
575
380
460
575
380
460
575
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
1.15
1.15
1.15
1.15
1.15
1.15
1.15
1.15
1.15
1.15
1.15
1.15
1.15
1.15
1.15
1.15
1.15
1.15
1.15
1.15
1.15
69.6
57.5
46.0
84.3
69.6
55.7
98.4
81.3
65.0
125
100
80
159
131
105
195
161
129
235
194
155
38
38
38
47
47
47
55
55
55
68
68
68
88
88
88
109
109
109
133
133
133
78.7
65.0
52.0
95.4
78.8
63.0
112
92.1
73.7
141
114
92
181
149
119
223
184
148
269
222
178
43
43
43
53
53
53
62
62
62
77
77
77
100
100
100
125
125
125
151
151
151
.11 - .14
.16 - .19
.25 - .31
.07 - .09
.11 - .14
.18 - .22
.06 - .07
.09 - .11
.13 - .16
.05 - .06
.07 - .09
.11 - .14
.04 - .05
.05 - .07
.08 - .10
.03 - .04
.04 - .06
.07 - .09
.02 - .03
.03 - .05
.05 - .07
RATING
FULL LOAD
EFFICIENCY
%
S.F.
F.L.
LOCKED
ROTOR
AMPS
79
79
79
81
81
81
83
83
83
83
83
83
86
86
86
86
86
86
85
85
85
78
78
78
80
80
80
82
82
82
82
82
82
85
85
85
85
85
85
84
84
84
616
509
407
832
687
550
1081
893
715
1175
922
738
1508
1246
997
1793
1481
1185
2012
1662
1330
Model numbers above are for three-lead motors. Six-lead motors with different model numbers have the same running
performance, but when Wye connected for starting have locked rotor amps 33% of the values shown. Six-lead individual
phase resistance = table X 1.5.
27
!00,)#!4)/.
4HREE 0HASE -OTORS
Table 28 Three-Phase Motor Fuse Sizing
TYPE
8"
STD.
MOTOR
MODEL
PREFIX
239660
239600
239610
239661
239601
239611
239662
239602
239612
239663
239603
239613
239664
239604
239614
239165
239105
239115
239166
239106
239116
239167
239107
239117
239168
239108
239118
CIRCUIT BREAKERS OR FUSE AMPS
RATING
HP
KW
40
30
50
37
60
45
75
55
100
75
125
93
150
110
175
130
200
150
CIRCUIT BREAKERS OR FUSE AMPS
(MAXIMUM PER NEC)
(TYPICAL SUBMERSIBLE)
VOLTS
STANDARD
FUSE
DUAL ELEMENT
TIME DELAY FUSE
CIRCUIT
BREAKER
STANDARD
FUSE
DUAL ELEMENT TIME
DELAY FUSE
CIRCUIT
BREAKER
380
460
575
380
460
575
380
460
575
380
460
575
380
200
175
150
250
200
175
300
250
200
350
300
250
500
125
100
80
150
125
90
175
150
110
200
175
150
275
175
150
110
200
175
150
250
200
175
300
250
200
400
200
175
125
225
200
150
300
225
175
350
300
225
450
80
70
60
100
80
70
125
100
80
150
125
100
200
175
150
110
200
175
150
250
200
175
300
250
200
400
460
575
380
460
575
380
460
575
380
460
575
380
460
575
400
350
700
500
450
800
600
500
800
700
600
1000
800
600
225
200
400
300
250
450
350
300
500
400
350
600
450
350
350
300
600
450
350
600
500
400
700
600
450
800
700
500
400
300
600
500
400
700
600
450
800
700
600
1000
800
600
175
125
250
225
175
300
250
200
350
300
225
400
350
250
350
300
600
450
350
600
500
400
700
600
450
800
700
500
Table 28A 8” Three-Phase Motor Fuse Sizing
TYPE
8"
HITEMP
MOTOR
MODEL
PREFIX
279160
279100
279110
279161
279101
279111
279162
279102
279112
279163
279103
279113
279164
279104
279114
279165
279105
279115
279166
279106
279116
CIRCUIT BREAKERS OR FUSE AMPS
RATING
HP
KW
40
30
50
37
60
45
75
56
100
75
125
93
150
110
CIRCUIT BREAKERS OR FUSE AMPS
(MAXIMUM PER NEC)
(TYPICAL SUBMERSIBLE)
VOLTS
STANDARD
FUSE
DUAL ELEMENT
TIME DELAY FUSE
CIRCUIT
BREAKER
STANDARD
FUSE
DUAL ELEMENT TIME
DELAY FUSE
CIRCUIT
BREAKER
380
460
575
380
460
575
380
460
575
380
460
575
380
460
575
380
460
575
380
460
575
225
175
150
250
200
175
300
275
200
400
300
275
500
400
350
700
500
450
800
600
500
125
110
90
150
125
100
175
150
125
200
175
150
300
250
200
400
300
250
450
350
300
175
150
125
225
175
150
250
225
175
350
275
225
450
350
300
600
450
350
600
500
400
200
175
125
225
200
150
300
250
175
350
300
225
450
400
300
600
500
400
700
600
450
90
70
60
110
90
70
125
100
80
150
125
100
200
175
125
250
225
175
300
250
200
175
150
125
225
175
150
250
225
175
350
275
225
450
350
300
600
450
350
600
500
400
28
!00,)#!4)/.
4HREE 0HASE -OTORS
/VERLOAD 0ROTECTION OF 4HREE 0HASE 3UBMERSIBLE -OTORS
The characteristics of submersible motors are different
than standard motors and special overload protection
is required.
All heaters and amp settings shown are based on total
line amps. When determining amperage settings or
making heater selections for a six-lead motor with a
Wye-Delta starter, divide motor amps by 1.732.
If the motor is locked, the overload protection must trip
within 10 seconds to protect the motor windings. Subtrol/
SubMonitor, a Franklin-approved adjustable overload
relay, or a Franklin-approved fixed heater must be used.
Pages 29, 30 and 31 list the correct selection and
settings for some manufacturers. Approval for other
manufacturers’ types not listed may be requested by
calling Franklin’s Submersible Service Hotline at
800-348-2420.
Fixed heater overloads must be the ambient-compensated
quick-trip type to maintain protection at high and low
air temperatures.
Refer to notes on page 30.
Table 29 - 60 Hz 4" Motors
HP
KW
1/2
0.37
3/4
0.55
1
0.75
1.5
1.1
2
1.5
3
2.2
5
3.7
7.5
5.5
10
7.5
29
VOLTS
NEMA
STARTER
SIZE
200
230
380
460
575
200
230
380
460
575
200
230
380
460
575
200
230
380
460
575
200
230
380
460
575
200
230
380
460
575
200
230
380
460
575
200
230
380
460
575
380
460
575
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
0
0
0
00
00
0
0
0
0
0
1
1
0
0
0
1
1
1
1
1
1
1
1
HEATERS FOR
OVERLOAD RELAYS
FURNAS
(NOTE 1)
K31
K28
K22
K34
K32
K27
K23
K21
K37
K36
K28
K26
K23
K42
K39
K32
K29
K26
K50
K49
K36
K33
K29
K55
K52
K41
K37
K34
K62
K61
K52
K49
K42
K68
K67
K58
K55
K52
K62
K60
K56
G.E.
(NOTE 2)
L380A
L343A
L211A
L174A
L510A
L420A
L282A
L211A
L193A
L618A
L561A
L310A
L282A
L211A
L750A
L680A
L420A
L343A
L282A
L111B
L910A
L561A
L463A
L380A
L147B
L122B
L750A
L618A
L510A
L241B
L199B
L122B
L100B
L825A
L332B
L293B
L181B
L147B
L122B
L241B
L199B
L165B
ADJUSTABLE
RELAYS
(NOTE 3)
SET
3.2
2.7
1.7
1.4
1.2
4.1
3.5
2.3
1.8
1.5
5.0
4.4
2.6
2.2
1.8
6.3
5.5
3.3
2.8
2.2
8.6
7.5
4.6
3.8
3.0
11.6
10.1
6.1
5.1
4.1
19.1
16.6
10.0
8.3
6.6
28.4
24.6
14.9
12.3
9.9
19.5
16.1
12.9
#LASS 0ROTECTION 2EQUIRED
MAX.
3.4
2.9
1.8
1.5
1.3
4.4
3.8
2.5
1.9
1.6
5.4
4.7
2.8
2.4
1.9
6.8
5.9
3.6
3.0
2.4
9.3
8.1
4.9
4.1
3.2
12.5
10.9
6.6
5.5
4.4
20.5
17.8
10.8
8.9
7.1
30.5
26.4
16.0
13.2
10.6
21.0
17.3
13.6
!00,)#!4)/.
4HREE 0HASE -OTORS
Table 30 - 60 Hz 6" Standard & Hi-Temp Motors
HP
5
7.5
10
15
20
25
30
40
50
60
KW
3.7
5.5
7.5
11
15
18.5
22
30
37
45
VOLTS
NEMA
STARTER
SIZE
200
230
HEATERS FOR
OVERLOAD RELAYS
ADJUSTABLE
RELAYS
(NOTE 3)
FURNAS
(NOTE 1)
G.E.
(NOTE 2)
SET
1
K61
L220B
17.6
19.1
1
K61
L199B
15.4
16.6
10.1
MAX.
380
0
K52
L122B
9.4
460
0
K49
L100B
7.7
8.3
575
0
K42
L825A
6.1
6.6
200
1
K67
L322B
26.3
28.3
230
1
K64
L293B
22.9
24.6
380
1
K57
L165B
13.9
14.9
460
1
K54
L147B
11.4
12.3
575
1
K52
L111B
9.1
9.8
200
2(1)
K72
L426B
34.4
37.0
230
2(1)
K70
L390B
29.9
32.2
380
1
K61
L220B
18.1
19.5
460
1
K58
L181B
15.0
16.1
575
1
K55
L147B
12.0
12.9
200
3(1)
K76
L650B
50.7
54.5
230
2
K75
L520B
44.1
47.4
380
2(1)
K68
L322B
26.7
28.7
460
2(1)
K64
L265B
22.0
23.7
575
2(1)
K61
L220B
17.7
19.0
200
3
K78
L787B
64.8
69.7
230
3(1)
K77
L710B
56.4
60.6
380
2
K72
L426B
34.1
36.7
460
2
K69
L352B
28.2
30.3
575
2
K64
L393B
22.7
24.4
200
3
K86
L107C
80.3
86.3
230
3
K83
L866B
69.8
75.0
380
2
K74
L520B
42.2
45.4
460
2
K72
L426B
34.9
37.5
575
2
K69
L352B
27.9
30.0
200
4(1)
K88
L126C
96.7
104.0
230
3
K87
L107C
84.1
90.4
380
3(1)
K76
L650B
50.9
54.7
460
3(1)
K74
L520B
42.0
45.2
575
3(1)
K72
L390B
33.7
36.2
380
3
K83
L866B
69.8
75.0
460
3
K77
L710B
57.7
62.0
575
3
K74
L593B
46.1
49.6
380
3
K87
L107C
86.7
93.2
460
3
K83
L950B
71.6
77.0
575
3
K77
L710B
57.3
61.6
380
4(1)
K89
L126C
102.5
110.2
460
4(1)
K87
L107C
84.6
91.0
575
4(1)
K78
L866B
67.7
72.8
Footnotes for Tables 29, 30, and 31
NOTE 1: Furnas intermediate sizes between
NEMA starter sizes apply where (1) is shown in
tables, size 1.75 replacing 2, 2.5 replacing 3, 3.5
replacing 4, and 4.5 replacing 5. Heaters were
selected from Catalog 294, table 332 and table
632 (starter size 00, size B). Size 4 starters are
heater type 4 (JG). Starters using these heater
tables include classes 14, 17 and 18 (inNOVA),
classes 36 and 37 (reduced voltage), and classes
87, 88 and 89 (pump and motor control centers).
Overload relay adjustments should be set no
higher than 100% unless necessary to stop
nuisance tripping with measured amps in all lines
below nameplate maximum. Heater selections for
class 16 starters (Magnetic Definite Purpose) will
be furnished upon request.
NOTE 2: General Electric heaters are type CR123
usable only on type CR124 overload relays and
were selected from Catalog GEP-126OJ,
page 184. Adjustment should be set no higher
than 100%, unless necessary to stop nuisance
tripping with measured amps in all lines below
nameplate maximum.
NOTE 3: Adjustable overload relay amp settings
apply to approved types listed. Relay adjustment
should be set at the specified SET amps. Only if
tripping occurs with amps in all lines measured to
be within nameplate maximum amps should the
setting be increased, not to exceed the MAX
value shown.
NOTE 4: Heaters shown for ratings requiring
NEMA size 5 or 6 starters are all used with
current transformers per manufacturer standards.
Adjustable relays may or may not use current
transformers depending on design.
30
!00,)#!4)/.
4HREE 0HASE -OTORS
Table 31 - 60 Hz 8" Motors
MOTOR
MODEL
PREFIX
239660
239600
239610
239661
239601
239611
239662
239602
239612
239663
239603
239613
239664
239604
239614
239165
239105
239115
239166
239106
239116
239167
239107
239117
239168
239108
239118
HP
KW
40
30
50
37
60
45
75
55
100
75
125
93
150
110
175
130
200
150
NEMA
VOLTS STARTER
SIZE
380
460
575
380
460
575
380
460
575
380
460
575
380
460
575
380
460
575
380
460
575
380
460
575
380
460
575
3
3
3
3
3
3
4(1)
4(1)
4(1)
4
4(1)
4(1)
5(1)
4
4
5
5(1)
5(1)
5
5(1)
5(1)
6
5
5
6
5
5
Table 31A - 60 Hz 8" Hi-Temp 75°C Motors
HEATERS FOR
OVERLOAD RELAYS
FURNAS
(NOTE 1)
K78
K77
K73
K86
K78
K77
K89
K86
K78
K92
K89
K85
K28
K92
K90
K32
K29
K26
K32
K28
K26
K33
K31
K27
K33
K32
G.E.
(NOTE 2)
L866B
L710B
L520B
L107C
L866B
L710B
L126C
L107C
L787B
L142C
L126C
L950C
L100B
L155C
L142C
L135B
L111B
L825A
L147B
L122B
L100B
L147B
L111B
L165B
L135B
ADJUSTABLE
RELAYS
(NOTE 3)
SET
68
56
45
81
68
56
101
83
64
121
100
79
168
134
108
207
176
140
248
206
165
270
233
186
316
266
213
MAX.
73
60
48
87
73
60
108
89
69
130
107
85
181
144
116
223
189
150
267
221
177
290
250
200
340
286
229
MOTOR
MODEL
PREFIX
279160
279100
279110
279161
279101
279111
279162
279102
279112
279163
279103
279113
279164
279104
279114
279165
279105
279115
279166
279106
279116
HP
KW
40
30
50
37
60
45
75
56
100
75
125
93
150
110
NEMA
VOLTS STARTER
SIZE
380
460
575
380
460
575
380
460
575
380
460
575
380
460
575
380
460
575
380
460
575
3
3
3
3
3
3
4(1)
4(1)
4(1)
4
4(1)
4(1)
5(1)
5(1)
4
5
5(1)
5(1)
5
5(1)
5(1)
HEATERS FOR
OVERLOAD RELAYS
FURNAS
(NOTE 1)
K83
K77
K74
K87
K83
K77
K89
K87
K78
K92
K89
K87
K28
K26
K90
K32
K29
K26
K32
K28
G.E.
(NOTE 2)
L866B
L710B
L593B
L107C
L866B
L710B
L126C
L107C
L866B
L155C
L126C
L950C
L100B
L825A
L142C
L135B
L111B
L825A
L147B
L122B
L100B
ADJUSTABLE
RELAYS
(NOTE 3)
SET
73
60
48
89
73
59
104
86
69
131
106
86
168
139
111
207
171
138
250
206
166
MAX.
79
65
52
95
79
63
112
92
74
141
114
92
181
149
119
223
184
148
269
222
178
Note: Other relay types from these and other manufacturers may or
may not provide acceptable protection, and they should not be used
without approval of Franklin Electric.
Some approved types may only be available for part of the listed motor
ratings. When relays are used with current transformers, relay setting
is the specified amps divided by the transformer ratio.
Recommended Adjustable Overload Relays
Advance Controls: MDR3 Overload
Lovato: RC9, RC22, RC80, RF9, RF25 & RF95
AEG Series: B17S, B27S, B27-2
Matsushita: FKT-15N, 15GN, 15E, 15GE, FT-15N, FHT-15N
ABB Type: RVH 40, RVH65, RVP160, T25DU, T25CT, TA25DU
Mitsubishi: ET, TH-K12ABKP, TH-K20KF, TH-K20KP,
TH-K20TAKF, TH-K60KF, TH-K60TAKF
AGUT: MT03, R1K1, R1L0, R1L3, TE set Class 5
Allen Bradley: Bulletin 193, SMP-Class 10 only
Automatic Switch Types: DQ, LR1-D, LR1-F, LR2 Class 10
Benshaw: RSD6 (Class 10) Soft Start
Bharita C-H: MC 305 ANA 3
Clipsal: 6CTR, 6MTR
Cutler-Hammer: C316F, C316P, C316S, C310-set at 6 sec
max, Advantage Class10
Fanal Types: K7 or K7D through K400
Franklin Electric: Subtrol-Plus, SubMonitor
Fuji Types: TR-OQ, TR-OQH, TR-2NQ, TR- 3NQ, TR-4NQ,
TR-6NQ, RCa 3737-ICQ & ICQH
Furnas Types: US15 48AG & 48BG, 958L, ESP100-Class 10
only, 3RB10-Class 10
General Electric: CR4G, CR7G, RT*1, RT*2, RTF3, RT*4,
CR324X-Class 10 only
Kasuga: RU Set Operating Time Code = 10 & time setting
6 sec max
Klockner-Moeller Types: ZOO, Z1, Z4, PKZM1, PKZM3
& PKZ2
31
Omron: K2CM Set Operating Timing Code = 10 & time setting
6 sec max, SE-KP24E time setting 6 sec max
Riken: PM1, PM3
Samwha: EOCRS Set for Class 5, EOCR-ST, EOCR-SE,
EOCR-AT time setting 6 sec max
Siemens Types: 3UA50, -52, -54, -55, -58, -59, -60, -61, -62,
-66, -68, -70, 3VUI3, 3VE, 3UB (Class 5)
Sprecher and Schuh Types: CT, CT1, CTA 1, CT3K, CT3-12
thru CT3-42, KTA3, CEF1 & CET3 set at 6 sec max, CEP 7
Class 10, CT4, 6, & 7, CT3, KT7
Square D/Telemecanique: Class 9065 Types: TD, TE, TF, TG,
TJ, TK, TR, TJE &TJF (Class 10), LR1-D, LR1-F, LR2 Class
10, Types 18A, 32A, SS-Class 10, SR-Class 10 and 63-A-LB
Series. Integral 18,32,63, GV2-L, GV2-M, GV2-P, GV3-M
(1.6-10 amp only) LR9D, SF Class 10, ST Class 10, LT6
(Class 5 or 10), LRD (Class 10), Motor Logic (Class10)
Toshiba Type: 2E RC820, set at 8 sec max.
WEG: RW2
Westinghouse Types: FT13, FT23, FT33, FT43, K7D, K27D,
K67D, Advantage (Class 10), MOR, IQ500 (Class 5)
Westmaster: OLWROO and OLWTOO suffix D thru P
35"-%23)",% 05-0
)NSTALLATION #HECK ,IST
1. Motor Inspection
A. Verify that the model, hp or kW, voltage, phase and hertz on the motor nameplate match the
installation requirements.
B. Check that the motor lead assembly is not damaged.
C. Measure insulation resistance using a 500 or 1000 volt DC megohmmeter from each lead wire to the
motor frame. Resistance should be at least 200 megohms without drop cable.
D. Keep a record of motor model number, hp or kW, voltage, and serial number (S/N).
(S/N is stamped in shell above the nameplate. A typical example, S/N 07A18 01-0123)
2. Pump Inspection
A. Check that the pump rating matches the motor.
B. Check for pump damage and verify that the pump shaft turns freely.
3. Pump/Motor Assembly
A. If not yet assembled, check that pump and motor mounting faces are free from dirt, debris and uneven
paint thickness.
B. Pumps and motors over 5 hp should be assembled in the vertical position to prevent stress on pump
brackets and shafts. Assemble the pump and motor together so their mounting faces are in contact and
then tighten assembly bolts or nuts evenly to manufacturer specifications.
C. If accessible, check that the pump shaft turns freely.
D. Assemble the pump lead guard over the motor leads. Do not cut or pinch lead wires during assembly
or installation.
4. Power Supply and Controls
A. Verify that the power supply voltage, Hertz, and kVA capacity match motor requirements.
B. Verify control box hp and voltage matches motor (3-wire only).
C. Check that the electrical installation and controls meet all safety regulations and match the motor
requirements, including fuse or circuit breaker size and motor overload protection. Connect all metal
plumbing and electrical enclosures to the power supply ground to prevent shock hazard. Comply with
national and local codes.
5. Lightning and Surge Protection
A. Use properly rated surge (lightning) arrestors on all submersible pump installations. Motors 5 hp and
SMALLER WHICH ARE MARKED h%QUIPPED WITH ,IGHTNING !RRESTORSv CONTAIN INTERNAL ARRESTORS
B. Ground all above ground arrestors with copper wire directly to the motor frame, or to metal drop pipe or
casing which reaches below the well pumping level. Connecting to a ground rod does not provide good
surge protection.
6. Electrical Drop Cable
A. Use submersible cable sized in accordance with local regulations and the cable charts. See pages 11 and
16-21. Ground motor per national and local codes.
B. Include a ground wire to the motor and surge protection, connected to the power supply ground if
required by codes. Always ground any pump operated outside a drilled well.
7. Motor Cooling
A. Ensure at all times that the installation provides adequate motor cooling; see page 6 for details.
Form No. 3656 11/09 © 2009 Franklin Electric Co., Inc.
35"-%23)",% 05-0
)NSTALLATION #HECK ,IST
8. Pump/Motor Installation
A. Splice motor leads to supply cable using electrical grade solder or compression connectors, and carefully
insulate each splice with watertight tape or adhesive-lined shrink tubing, as shown in motor or pump
installation data.
B. Support the cable to the delivery pipe every 10 feet (3 meters) with straps or tape strong enough to
prevent sagging. Use padding between cable and any metal straps.
C. A check valve in the delivery pipe is recommended. More than one check valve may be required,
depending on valve rating and pump setting; see page 5 for details.
D. Assemble all pipe joints as tightly as practical, to prevent unscrewing from motor torque. Torque should
be at least 10 pound feet per hp (2 meter-KG per kW).
E. Set the pump far enough below the lowest pumping level to assure the pump inlet will always have at
least the Net Positive Suction Head (NPSH) specified by the pump manufacturer. Pump should be at
least 10 feet (3 meters) from the bottom of the well to allow for sediment build up.
F. Check insulation resistance as pump/motor assembly is lowered into the well. Resistance may drop
gradually as more cable enters the water, but any sudden drop indicates possible cable, splice or motor
lead damage; see page 45.
9. After Installation
A. Check all electrical and water line connections and parts before starting the pump.
B. Start the pump and check motor amps and pump delivery. If normal, continue to run the pump until delivery
is clear. If three-phase pump delivery is low, it may be running backward. Rotation may be reversed (with
power off) by interchanging any two motor lead connections to the power supply.
C. Check three-phase motors for current balance within 5% of average, using motor manufacturer instructions
Imbalance over 5% will cause higher motor temperatures and may cause overload trip, vibration, and
reduced life.
D. Verify that starting, running and stopping cause no significant vibration or hydraulic shocks.
E. After at least 15 minutes running time, verify that pump output, electrical input, pumping level, and other
characteristics are stable and as specified.
Date _____________________ Filled In By _________________________________________________________________
Notes _______________________________________________________________________________________________
____________________________________________________________________________________________________
____________________________________________________________________________________________________
____________________________________________________________________________________________________
____________________________________________________________________________________________________
____________________________________________________________________________________________________
Form No. 3656 11/09 © 2009 Franklin Electric Co., Inc.
2-! .UMBER
35"-%23)",% -/4/2 ).34!,,!4)/. 2%#/2$
&ORM
0AGE
+%9 $%!,%2
$)342)"54/2
).34!,,%2
%.$ 53%2
Name: _________________________
Name: _________________________
Name: _________________________
City: ___________________________
City: ___________________________
City: ___________________________
State: ___________ Zip: __________
State: ___________ Zip: __________
State: ___________ Zip: __________
°F
Well ID or GPS: __________ ___________ ______________________ Water Temperature: _____________
°C
Application/Water Use (e.g. potable water, irrigation, municipal, fountain, etc.): ___________________________________
Yes
Date Installed (mm/yy): _____________ Date Failed (mm/yy):_____________ Motor Position Shaft-Up:
Hrs.
Operating Cycle: ON Time Per Start _____
Mins. Time OFF Between Stop & Restart _____
Hrs.
No
Mins.
-/4/2
Model: ______________________ Serial Number: __________________________ Date Code (if updated): __________
-/4/2 /6%2,/!$
System Typical Operating Current: _______________ Amps @ _______________ Volts
Overload:
FE SubMonitor Input Amps _______ D3 Attached
Yes
No Fault Settings Attached
Yes
No
Other Manufacturer Model: _______________________ Dial Set at: __________ or Heater# __________
NEMA Class:
Power to Motor by:
10
20
Full Volt Starter
30
Ambient Compensated:
VFD
05-0
Yes
No
Soft Starter VFD or Soft Starter Mfr. & Model: ___________________
7%,, $!4! (All measurements from well head down.)
Manufacturer:_________________________
Casing Diameter ______________________ in
Model: ______________________________
Drop Pipe Diameter ____________________ in
Stages:______________________________
Number of Sticks of Drop Pipe _____________
Design Rating: _______ gpm @ _______ ft TDH
Static Water Level _____________________ ft
Horsepower Required by Pump End: ___________
Drawdown (pumping) Water Level _________ ft
Actual Pump Delivery: _______ gpm @ _______ psi
Spring Assist Check Valves:
(Measured from Well Head Down)
What Controls When System Runs & Stops:
_________________________________________
(e.g. pressure, level, flow, manual on/off, timer,
time clock etc.)
#1 ______ #2______ #3 ______ #4______ ft
Solid
Drilled Poppet
Break-Off Plug
Pump Inlet Setting ____________________ ft
Flow Sleeve
No
Yes, Dia. _________ in
Case Ends ___________________________ ft
9/52 .!-% $!4%
____________________________ / ___________
Form No. 2207 v6 05/11 © 2009 Franklin Electric Co., Inc.
Well Screen
Perforated Casing
#1 from ____to____ft & #2 from ____to____ft
Well Depth ___________________________ ft
2-! .UMBER
35"-%23)",% -/4/2 ).34!,,!4)/. 2%#/2$
&ORM
0AGE
42!.3&/2-%23
Number of Transformers:
Two
Transformer #1: __________ kVA
Three
Transformers Supply Motor Only:
Transformer #2: __________ kVA
Yes
No
Unsure
Transformer #3: __________ kVA
0/7%2 #!",%3 '2/5.$ 7)2%
Service Entrance to Pump Control Panel:
1
Length: __________ ft. & Gauge: __________ AWG/MCM
Material:
Copper
Aluminum
Temperature Rating of Cable:
Construction:
60C
75C
90C
Jacketed
Individual Conductors
Web
Twisted
125C or Insulation Type: ________________ (e.g. THHN)
Pump Control Panel to Motor:
2
Length: __________ ft. & Gauge: __________ AWG/MCM
Material:
Copper
Aluminum
Temperature Rating of Cable:
Construction:
60C
75C
90C
Jacketed
Individual Conductors
Web
Twisted
125C or Insulation Type: ________________ (e.g. THHN)
Ground Wire Size: From Control Panel to Motor: __________ AWG/MCM
3 Control Grounded to (mark all that apply):
Well Head
Metal Casing
Motor
Driven Rod
Power Supply
).#/-).' 6/,4!'%
25..).' !-03 #522%.4 "!,!.#%
No Load
L1-L2 ______ L2-L3 ______ L1-L3 ______
Full Load
Full Load
L1-L2 ______ L2-L3 ______ L1-L3 ______
% Unbalance: ______
L1 ________ L2 ________ L3 ________
#/.42/, 0!.%,
1 Pump Panel Manufacturer/Fabricator: _______________________________________________________________
Short Circuit Protection - Fuses or Circuit Breaker
Option #1 - Fuse
2
Manufacturer: __________________ Model: __________________ Rating: ____________ Amps
Type:
Time-Delay
Standard
Option #2 - Circuit Breaker
Manufacturer: __________________ Model: __________________ Rating: ___________ Amps Setting: _________
Starter - Full Voltage, Reduced Voltage, Soft-Starter or VFD (Variable Frequency Drive)
Option #1 - Full Voltage
Manufacturer: __________________ Model: ________________ Size: ____________ Contacts:
NEMA
IEC
Option #2 - Reduced Voltage
Manufacturer: __________________ Model: __________________ Ramp Time to Full Voltage: _____________ sec.
3 Option #3 - Soft-Starter or VFD
Manufacturer: __________________ Model: __________________ Max. Continuous Amp Output Rating: _________
Min. Setting: ____________ Hz & GPM: ____________
Start Ramp Time to 30 Hz: ________ sec.
Special Output Filter Purchased:
Yes
Stop Mode:
Max. Setting: ____________ Hz & GPM: ____________
Power Off Coast
30-0 Hz Ramp ________ sec.
No
Output Filter Manufacturer: ______________________ Model: ______________________ % Reactance: _________
4 Surge Arrestor:
No
Yes, Manufacturer: ____________________ Model: ____________________
Form No. 2207 v6 05/11 © 2009 Franklin Electric Co., Inc.
35"-%23)",% -/4/2
"OOSTER )NSTALLATION 2ECORD
2-! .UMBER
Date ______ /______/_______ Filled In By ______________________________________
).34!,,!4)/.
Owner/User ________________________________________________ Telephone (______) ____________________
Address ____________________________________________City _______________ State ______ Zip ___________
Installation Site, If Different _________________________________________________________________________
Contact ___________________________________________________ Telephone (______) ____________________
System Application________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
System Manufactured By_____________________________Model ________________ Serial No. ________________
System Supplied By_________________________________ City _________________ State ______ Zip __________
)S THIS A h(%2/v SYSTEM 0(
Yes
No
-/4/2
Model No. _______________ Serial No. _______________ Date Code ______
Horsepower ______ Voltage ______
Slinger Removed?
Yes
Motor Fill Solution
Standard
Single-Phase
Three-Phase Diameter ______ in.
No Check Valve Plug Removed?
Yes
No
DI Water Model No. _____________ Serial No. _____________ Date Code ______
05-0
Manufacturer _______________ Model _______________ Serial No. _______________
Stages ______ Diameter ________ Flow Rate Of ________ gpm At ______TDH
Booster Case Internal Diameter ________ Material _______________
#/.42/,3 !.$ 02/4%#4)6% $%6)#%3
SubMonitor?
Yes
No
If Yes, Warranty Registration No._______________________________________
If Yes, Overload Set?
Underload Sets?
VFD or Reduced Voltage Starter?
Yes
Yes
Yes
No ______ Set At _________________________
No ______ Set At _________________________
No If Yes, Type __________________________________________
Mfr. ______________Setting ________% Full Voltage In ________sec
Pump Panel?
Yes
No If Yes, Mfr. ______________________________Size _______________________
Magnetic Starter/Contactor Mfr. ___________________________ Model __________________Size_______________
Heaters Mfr. _____________________ No. ____________ If Adjustable Set At ________________________________
Fuses Mfr. ____________________ Size ___________ Type ______________________________________________
Lightning/Surge Arrestor Mfr. ________________________ Model __________________________________________
Controls Are Grounded to __________________ with No. ________Wire
Inlet Pressure Control
Yes
No If Yes, Mfr.________ Model _______ Setting _____ psi
Delay ____ sec
Inlet Flow Control
Yes
No If Yes, Mfr.________ Model _______ Setting _____ gpm
Delay ____ sec
Outlet Pressure Control
Yes
No If Yes, Mfr.________ Model _______ Setting _____ psi
Delay ____ sec
Outlet Flow Control
Yes
No If Yes, Mfr.________ Model _______ Setting _____ gpm
Delay ____ sec
Water Temperature Control
Yes
No If Yes, Mfr.________ Model ________________________ Delay ____ sec
Set At ________ °F or ______ °C Located _____________________________________
Form No. 3655 11/09 © 2009 Franklin Electric Co., Inc.
35"-%23)",% -/4/2
"OOSTER )NSTALLATION 2ECORD
).35,!4)/. #(%#+
Initial Megs: Motor & Lead Only
Black (T1/U1)_________ Yellow (T2/V1)________ Red (T3/W1)_________
Installed Megs: Motor, Lead, & Cable
Black (T1/U1)_________ Yellow (T2/V1)________ Red (T3/W1)_________
6/,4!'% 4/ -/4/2
Non-Operating:
B-Y (T1/U1 - T2/V1)_____ Y-R (T2/V1 - T3/W1)_____ R-B (T3/W1 - T1/U1)_____
At Rated Flow of __________gpm
B-Y (T1/U1 - T2/V1)_____ Y-R (T2/V1 - T3/W1)_____ R-B (T3/W1 - T1/U1)_____
At Open Flow ____________gpm
B-Y (T1/U1 - T2/V1)_____ Y-R (T2/V1 - T3/W1)_____ R-B (T3/W1 - T1/U1)_____
!-03 4/ -/4/2
At Rated Flow of __________gpm
Black (T1/U1)_________ Yellow (T2/V1)________ Red (T3/W1)_________
At Open Flow ____________gpm
Black (T1/U1)_________ Yellow (T2/V1)________ Red (T3/W1)_________
At Shut Off*
Black (T1/U1)_________ Yellow (T2/V1)________ Red (T3/W1)_________
*Do NOT run at Shut Off more than two (2) minutes.
Inlet Pressure __________psi
Outlet Pressure __________psi
Water Temperature _______ °F or _______ °C
If you have any questions or problems, call the Franklin Electric Toll-Free Hot Line: 1-800-348-2420
Comments: _____________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
0,%!3% 3+%4#( 4(% 3934%-
Form No. 3655 11/09 © 2009 Franklin Electric Co., Inc.
!00,)#!4)/.
4HREE 0HASE -OTORS
3UB-ONITOR 4HREE 0HASE 0ROTECTION
Applications
SubMonitor is designed to protect 3-phase pumps/
motors with service factor amp ratings (SFA) from 5
to 350 A (approx. 3 to 200 hp). Current, voltage, and
motor temperature are monitored using all three legs
and allows the user to set up the SubMonitor quickly
and easily.
Protects Against
s
s
s
s
5NDER/VERLOAD
5NDER/VERVOLTAGE
#URRENT 5NBALANCE
/VERHEATED -OTOR
(if equipped with Subtrol Heat Sensor)
s &ALSE 3TART #HATTERING
s 0HASE 2EVERSAL
0OWER &ACTOR #ORRECTION
In some installations, power supply limitations make it
necessary or desirable to increase the power factor of a
submersible motor. The table lists the capacitive kVAR
required to increase the power factor of large Franklin
three-phase submersible motors to the approximate
values shown at maximum input loading.
Capacitors must be connected on the line side of the
overload relay, or overload protection will be lost.
Table 32 kVAR Required 60 Hz
MOTOR
HP
5
KVAR REQUIRED FOR PF OF:
KW
0.90
0.95
1.00
3.7
1.2
2.1
4.0
7.5
5.5
1.7
3.1
6.0
10
7.5
1.5
3.3
7.0
15
11
2.2
4.7
10.0
20
15
1.7
5.0
12.0
25
18.5
2.1
6.2
15.0
30
22
2.5
7.4
18.0
40
30
4.5
11.0
24.0
7.1
15.0
32.0
50
37
60
45
8.4
18.0
38.0
75
55
6.3
18.0
43.0
100
75
11.0
27.0
60.0
125
93
17.0
36.0
77.0
150
110
20.0
42.0
90.0
175
130
9.6
36.0
93.0
200
150
16.0
46.0
110.0
Values listed are total required (not per phase).
32
!00,)#!4)/.
4HREE 0HASE -OTORS
4HREE 0HASE 3TARTER $IAGRAMS
Three-phase combination magnetic starters have two
distinct circuits: a power circuit and a control circuit.
The power circuit consists of a circuit breaker or
fused line switch, contacts, and overload heaters
connecting incoming power lines L1, L2, L3 and the
three-phase motor.
The control circuit consists of the magnetic coil, overload
contacts and a control device such as a pressure switch.
When the control device contacts are closed, current
flows through the magnetic contactor coil, the contacts
close, and power is applied to the motor. Hand-Off-Auto
switches, start timers, level controls and other control
devices may also be in series in the control circuit.
L1
L3
L2
Line Voltage Control
This is the most common type of control encountered.
Since the coil is connected directly across the power
lines L1 and L2, the coil must match the line voltage.
PRESSURE SWITCH OR
OTHER CONTROL DEVICE
FUSES
O.L. CONTACTS
COIL
CONTACTS
OVERLOAD
HEATERS AND/OR
SUBTROL PLUS
MOTOR
L1
Low Voltage Transformer Control
This control is used when it is desirable to operate push
buttons or other control devices at some voltage lower
than the motor voltage. The transformer primary must
match the line voltage and the coil voltage must match
the secondary voltage of the transformer.
L2
FIG. 7
L3
PRESSURE SWITCH OR
OTHER CONTROL DEVICE
FUSES
O.L. CONTACTS
COIL
FUSE
TRANSFORMER
CONTACTS
OVERLOAD
HEATERS AND/OR
SUBTROL PLUS
MOTOR
L1
External Voltage Controls
Control of a power circuit by a lower circuit voltage can
also be obtained by connecting to a separate control
voltage source. The coil rating must match the control
voltage source, such as 115 or 24 volts.
L2
FIG. 8
L3
PRESSURE SWITCH OR
OTHER CONTROL DEVICE
FUSES
O.L. CONTACTS
COIL
CONTACTS
OVERLOAD
HEATER AND/OR
SUBTROL DEVICE
MOTOR
33
FIG. 9
TO SEPARATE
CONTROL VOLTAGE
SOURCE
!00,)#!4)/.
4HREE 0HASE -OTORS
4HREE 0HASE 0OWER 5NBALANCE
A full three-phase supply is recommended for all threephase motors, consisting of three individual transformers
OR ONE THREE PHASE TRANSFORMER 3O CALLED hOPENv DELTA
or Wye connections using only two transformers can be
used, but are more likely to cause problems, such as
FIG. 10
FULL THREE-PHASE
poor performance, overload tripping or early motor failure
due to current unbalance.
Transformer rating should be no smaller than listed in
table 4 for supply power to the motor alone.
FIG. 11
OPEN DELTA
#HECKING AND #ORRECTING 2OTATION AND #URRENT 5NBALANCE
1. Establish correct motor rotation by running the
motor in both directions. Normal rotation is CCW
viewing the shaft end. Rotation can be changed by
interchanging any two of the three motor leads. The
rotation that gives the most water flow is typically the
correct rotation.
2. After correct rotation has been established, check the
current in each of the three motor leads and calculate
the current unbalance as explained in 3 below.
If the current unbalance is 2% or less, leave the leads
as connected.
If the current unbalance is more than 2%, current
readings should be checked on each leg using each
of three possible hook-ups. Roll the motor leads
across the starter in the same direction to prevent
motor reversal.
3. To calculate percent of current unbalance:
A. Add the three line amps values together.
D. Determine the difference between this amp
value (furthest from average) and the average.
E. Divide the difference by the average. Multiply the
result by 100 to determine percent of unbalance.
4. Current unbalance should not exceed 5% at max
amp load or 10% at rated input load. If the unbalance
cannot be corrected by rolling leads, the source of
the unbalance must be located and corrected. If, on
the three possible hookups, the leg farthest from the
average stays on the same power lead, most of the
UNBALANCE IS COMING FROM THE hPOWER SIDEv OF THE
system. If the reading farthest from average moves
with the same motor lead, the primary source of
UNBALANCE IS ON THE hMOTOR SIDEv OF THE STARTER )N THIS
instance, consider a damaged cable, leaking splice,
poor connection, or faulty motor winding.
Phase designation of leads for CCW rotation viewing
shaft end.
To reverse rotation, interchange any two leads.
B. Divide the sum by three, yielding
average current.
0HASE OR h!v "LACK 4 OR 5
C. Pick the amp value which is furthest from the
average current (either high or low).
0HASE OR h"v 9ELLOW 4 OR 6
0HASE OR h#v 2ED 4 OR 7
NOTICE: Phase 1, 2 and 3 may not be L1, L2 and L3.
1st Hook Up
L1
L2
L3
2nd Hook Up
L1
L2
L3
3rd Hook Up
L1
L2
L3
supply
starter
T2
T1
T1
T3
T3
T3
T2
T2
T1
motor
EXAMPLE:
T1 = 51 amps
T3 = 50 amps
T2 = 50 amps
T2 = 46 amps
T1 = 49 amps
T3 = 48 amps
+ T2 = 51 amps
+ T3 = 53 amps
+ T1 = 52 amps
Total = 150 amps Total = 150 amps Total = 150 amps
150
= 50 amps
3
150
= 50 amps
3
150
= 50 amps
3
50 - 46 = 4 amps
50 - 49 = 1 amp
50 - 48 = 2 amps
4 = 0.08 or 8%
50
1 = 0.02 or 2%
50
2 = 0.04 or 4%
50
34
!00,)#!4)/.
4HREE 0HASE -OTORS
4HREE 0HASE -OTOR ,EAD )DENTIlCATION
Line Connections — Six-Lead Motors
T5-V2
(YELLOW)
WARNING: When installing
6-lead motors extra care
must be used to ensure lead
identification at the surface.
Leads must be marked and
connected per diagram. Motor
leads are not connected red to
red, yellow to yellow, etc.
CHECK VALVE OR
PIPE PLUG ON RIGHT
SIDE FACING MOTOR
SHAFT
T6-W2
(RED)
T4-U2
(BLACK)
T2-V1
(YELLOW)
T1-U1
(BLACK)
T3-W1
(RED)
LEADS LOCATED HERE ONLY
FOR 3 LEAD (DOL) MOTORS
90° Lead Spacing
Connections for across-the-line starting,
running, and any reduced voltage starting
except WYE-DELTA type starters.
L1
T1
U1
L2
T6
W2
T2
V1
L3
T4
U2
T3
W1
T5
V2
WYE-DELTA starters connect the motor as
shown below during starting, then change to
the running connection shown at the left.
L1
L2
L3
T1
U1
T2
V1
T3
W1
T4
U2
T5
V2
T6
W2
Each motor lead is numbered with two markers, one near each end. To reverse rotation, interchange any two line connections.
0HASE #ONVERTERS
There are a number of different types of phase converters
available. Each generates three-phase power from a
single-phase power line.
In all phase converters, the voltage balance is critical to
current balance. Although some phase converters may
be well balanced at one point on the system-operating
curve, submersible pumping systems often operate
at differing points on the curve as water levels and
operating pressures fluctuate. Other converters may be
well balanced at varying loads, but their output may vary
widely with fluctuations in the input voltage.
The following guidelines have been established for
submersible installations to be warrantable when used
with a phase converter.
35
1. Limit pump loading to rated horsepower. Do not load
into motor service factor.
2. Maintain at least 3 ft/s flow past the motor. Use a flow
sleeve when necessary.
3. Use time delay fuses or circuit breakers in pump
panel. Standard fuses or circuit breakers do not
provide secondary motor protection.
4. SubMonitor may be used with electro mechanical
type phase converters, however special connections
are required. Consult SubMonitor Manual for
connections of receiver and lightning arrestor.
5. SubMonitor will not work with electronic solid state
phase converters.
6. Current unbalance must not exceed 10%.
!00,)#!4)/.
4HREE 0HASE -OTORS
2EDUCED 6OLTAGE 3TARTERS
All Franklin three-phase submersible motors are suitable
for full-voltage starting. Under this condition the motor
speed goes from zero to full speed within a half second
or less. The motor current goes from zero to locked rotor
amps, then drops to running amps at full speed. This
may dim lights, cause momentary voltage dips
to other electrical equipment, and shock power
distribution transformers.
In some cases the power companies may require
reduced-voltage starters to limit this voltage dip. There
are also times when reduced-voltage starters may be
desirable to reduce motor starting torque thus reducing
the stress on shafts, couplings, and discharge piping.
Reduced-voltage starters also slow the rapid acceleration
of the water on start-up to help control upthrust and
water hammer.
Reduced-voltage starters may not be required if the
maximum recommended cable length is used. With
maximum recommended cable length there is a 5%
voltage drop in the cable at running amps, resulting in
about 20% reduction in starting current and about 36%
reduction in starting torque compared to having rated
voltage at the motor. This may be enough reduction in
starting current so that reduced-voltage starters are
not required.
Three-Lead Motors: Autotransformer or solid-state
reduced-voltage starters may be used for soft-starting
standard three-phase motors.
When autotransformer starters are used, the motor
should be supplied with at least 55% of rated voltage to
ensure adequate starting torque. Most autotransformer
starters have 65% and 80% taps. Setting the taps on
these starters depends on the percentage of the
maximum allowable cable length used in the system.
If the cable length is less than 50% of the maximum
allowable, either the 65% or the 80% taps may be used.
When the cable length is more than 50% of allowable,
the 80% tap should be used.
Six-Lead Motors: Wye-Delta starters are used with
six-lead Wye-Delta motors. All Franklin 6" and 8"
three-phase motors are available in six-lead Wye-Delta
construction. Consult the factory for details and availability.
Part winding starters are not compatible with Franklin
Electric submersible motors and should not be used.
Wye-Delta starters of the open-transition type, which
momentarily interrupt power during the starting cycle, are
not recommended. Closed-transition starters have no
interruption of power during the start cycle and can be
used with satisfactory results.
Reduced-voltage starters have adjustable settings
for acceleration ramp time, typically preset at 30
seconds. They must be adjusted so the motor is at
full voltage within THREE SECONDS MAXIMUM to
prevent excessive radial and thrust bearing wear.
If Subtrol-Plus or SubMonitor is used the
acceleration time must be set to TWO SECONDS
MAXIMUM due to the 3 second reaction time of the
Subtrol-Plus or SubMonitor.
Solid-state starters AKA soft starts may not be
compatible with Subtrol-Plus/SubMonitor. However,
in some cases a bypass contactor has been used.
Consult the factory for details.
During shutdown, Franklin Electric’s
recommendation is for the power to be removed,
allowing the pump/motor to coast down. Stopping
the motor by ramping down the voltage is possible,
but should be limited to three (3) seconds maximum.
)NLINE "OOSTER 0UMP 3YSTEMS
Franklin Electric offers three different types of motors for
non-vertical applications.
1. The Booster motors are specifically designed for
booster applications. They are the “Best Choice”
for sealed Reverse Osmosis applications.
These motors are the result of two years of focused
development and bring additional value and durability
to booster module systems. These motors are
only available to OEMs or Distributors who have
demonstrated capability in Booster Module systems
design and operation and adhere to Franklin’s
Application Manual requirements.
2. The Hi-Temp motors have many of the internal
design features of the Booster motor. It’s additional
length allows for higher temperature handling and
the Sand Fighter sealing system provides greater
abrasion resistance. One or both of these conditions
Continued on next page
are often experienced in open atmosphere
applications such as lakes, ponds, etc.
3. The Standard Vertical Water Well (40-125 hp)
motors can be adapted to non-vertical applications
when applied per the below guidelines. However,
they will be more sensitive to application variances
than the other two designs.
All of the above motors must be applied per the
guidelines listed below. In addition, for all applications
where the motor is applied in a sealed system, a
Submersible Motor Booster Installation Record (Form
3655) or its equivalent must be completed at startup and
received by Franklin Electric within 60 days. A sealed
system is one where the motor and pump intake are
mounted in a sleeve and the water feeding the pump
intake is not open to the atmosphere.
36
!00,)#!4)/.
4HREE 0HASE -OTORS
)NLINE "OOSTER 0UMP 3YSTEMS CONTINUED
water must be done by an approved Franklin service
shop or representative using a vacuum fill system
per Franklin’s Motor Service Manual instruction. The
motor shell then must be permanently stamped with a
D closely behind the Serial Number.
Design And Operational Requirements
1. Non-Vertical Operation: Vertical Shaft-up (0°) to
Horizontal (90°) operation is acceptable as long as
THE PUMP TRANSMITS hDOWN THRUSTv TO THE MOTOR WITHIN
3 seconds after start-up and continuously during
operation. However, it is best practice to provide a
positive slope whenever it is possible, even if it is only
a few degrees.
3. Motor Support Points: A minimum of two support
points are required on the motor. One in the motor/
pump flange connection area and one in the bottom
end of the motor area. The motor castings, not the
shell area, are recommended as support points. If the
support is a full length support and/or has bands in
the shell area, they must not restrict heat transfer or
deform the shell.
Derating Factor for Motors That Must Have Their Factory Fill
Replaced With Deionized Water 8" Encapsulated Motor
1.8
1.75
1.7
Pump Load Multiplier
2. Motor, Sleeve, and Pump Support System: The
booster sleeve ID must be sized according to the
motor cooling and pump NPSHR requirements. The
support system must support the motor’s weight,
prevent motor rotation and keep the motor and pump
aligned. The support system must also allow for
thermal axial expansion of the motor without creating
binding forces.
The maximum pressure that can be applied to the
motor internal components during the removal of the
factory fill solution is 7 psi (0.5 bar.)
1.65
1.6
1.55
1.5
1.45
1.4
1.35
1.3
1.25
1.2
1.15
1.1
1.05
1
1.00 Service Factor
1.15 Service Factor
40
35
30
(50Hz)
(60Hz)
25
20
15
10
Feed Water Temperature (°C)
FIG. 12
Determine maximum Feed Water Temperature
that will be experienced in this application. If the
feed water exceeds the maximum ambient of the
motor, both the DI water derating and a hot water
application derating must be applied.
4. Motor Support Material and Design: The support
system shall not create any areas of cavitation or
other areas of reduced flow less than the minimum
rate required by this manual. They should also be
designed to minimize turbulence and vibration and
provide stable alignment. The support materials and
locations must not inhibit the heat transfer away from
the motor.
First:
5. Motor and Pump Alignment: The maximum
allowable misalignment between the motor, pump,
and pump discharge is 0.025 inch per 12 inches of
length (2 mm per 1000 mm of length). This must be
measured in both directions along the assembly using
the motor/pump flange connection as the starting
point. The booster sleeve and support system must
be rigid enough to maintain this alignment during
assembly, shipping, operation and maintenance.
Third:
Multiply the Pump Load Requirement times the pump
load multiplier number indicated on the vertical axis
to determine the Minimum Motor Nameplate Rating.
Fourth:
Select a motor with a nameplate equal or higher than
the above calculated value.
6. The best motor lubrication and heat resistance is
obtained with the factory based propylene glycol
fill solution. Only when an application MUST HAVE
deionized (DI) water should the factory fill solution
be replaced. When a deionized water fill is required,
the motor must be derated as indicated on the below
chart. The exchange of the motor fill solution to DI
37
Second: Determine the Pump Load Multiplier from the
appropriate Service Factor curve. (Typical 1.15
Service Factor is for 60 Hz ratings &1.00 Service
Factor for 50 Hz ratings).
7. Motor Alterations - Sand Slinger & Check Valve
Plug: /N v AND v MOTORS THE RUBBER SAND SLINGER
located on the shaft must be removed. If a pipe plug
is covering the check valve, it must be removed.
The special Booster motor already has these
modifications.
8. Frequency of Starts: Fewer than 10 starts per
24-hour period are recommended. Allow at least 20
minutes between shutdown and start-up of the motor.
Continued on next page
!00,)#!4)/.
4HREE 0HASE -OTORS
)NLINE "OOSTER 0UMP 3YSTEMS CONTINUED
9.
Controls-Soft Starters and VFDs: Reduced voltage
starters and variable speed drives (inverter drives)
may be used with Franklin three-phase submersible
motors to reduce starting current, upthrust, and
mechanical stress during start-up. The guidelines
for their use with submersible motors are different
than with normal air cooled motor applications.
Refer to the Franklin Electric Application, Installation
and Maintenance (AIM) Manual Reduced Voltage
Starters section or Variable Speed Submersible
Pump Operation, Inverter Drives sections for specific
details including required filtering.
Franklin Cable Chart tables 16-21. (Notice: wire size,
wire rating and insulation temperature rating must be
known when determining its suitability to operate in
air or conduit. Typically, for a given size and rating,
as the insulation temperature rating increases its
ability to operate in air or conduit also increases.)
13. Check Valves: Spring-loaded check valves must
be used on start-up to minimize motor upthrusting,
water hammer, or in multiple booster (parallel)
applications to prevent reverse flow.
14. Pressure Relief Valves: A pressure relief valve is
required and must be selected to ensure that, as the
pump approaches shut-off, it never reaches the point
that the motor will not have adequate cooling flow
past it.
10. Motor Overload Protection: Submersible motors
require properly sized ambient compensated
Class 10 quick-trip overloads per Franklin’s AIM
Manual guidelines to protect the motor. Class 20
or higher overloads are NOT acceptable. Franklin’s
SubMonitor is strongly recommended for all large
submersibles since it is capable of sensing motor
heat without any additional wiring to the motor.
Applications using Soft Starters with a SubMonitor
require a start-up bypass - consult the factory for
details. SubMonitor can not be used in applications
using a VFD control.
15. System Purge (Can Flooding): An air bleeder
valve must be installed on the booster sleeve so that
flooding may be accomplished prior to booster startup. Once flooding is complete, the booster should
be started and brought up to operating pressure as
quickly as possible to minimize the duration of an
upthrust condition. At no time should air be allowed
to gather in the booster sleeve because this will
prevent proper cooling of the motor and permanently
damage it.
11. Motor Surge Protection: Properly sized, grounded
and dedicated motor surge arrestors must be
installed in the supply line of the booster module as
close to the motor as possible. This is required on
all systems including those using soft-starters and
variable speed drives (inverter drives).
16. System Flush – Must Not Spin Pump: Applications
may utilize a low flow flushing operation. Flow
through the booster sleeve must not spin the pump
impellers and the motor shaft. If spinning takes
place, the bearing system will be permanently
damaged and the motor life shortened. Consult the
booster pump manufacturer for maximum flow rate
through the pump when the motor is not energized.
12. Wiring: Franklin’s lead assemblies are only sized
for submerged operation in water to the motor
nameplate maximum ambient temperature and
may overheat and cause failure or serious injury
if operated in air. Any wiring not submerged must
meet applicable national and local wiring codes and
Table 38 Franklin Cable chart (See 12. Wiring)
CABLE
TEMP.
RATING
(°C)
75
90
125
MOTOR
NAMEPLATE
RATED AMPS
FULL LOAD
#10 AWG
IN AIR
IN
CONDUIT
#8 AWG
IN AIR
IN
CONDUIT
#6 AWG
IN AIR
#4 AWG
IN
CONDUIT
IN AIR
#2 AWG
IN
CONDUIT
IN AIR
IN
CONDUIT
3-LEAD (DOL)
40A
28A
56A
40A
76A
52A
100A
68A
136A
92A
3,(+@¬
69A
48A
97A
69A
132A
90A
173A
118A
236A
159A
3-LEAD (DOL)
44A
32A
64A
44A
84A
60A
112A
76A
152A
104A
3,(+@¬
76A
55A
111A
76A
145A
104A
194A
132A
263A
180A
3-LEAD (DOL)
66A
46A
77A
53A
109A
75A
153A
105A
195A
134A
3,(+@¬
114A
80A
133A
91A
188A
130A
265A
181A
337A
232A
Based on 30 °C maximum ambient with cable length of 100 feet or less.
Continued on next page
38
!00,)#!4)/.
4HREE 0HASE -OTORS
)NLINE "OOSTER 0UMP 3YSTEMS CONTINUED
17. Open Atmosphere Booster Pump Systems: When
an open booster is placed in a lake, tank, etc. that is
open to atmospheric pressure, the water level must
provide sufficient head pressure to allow the pump
to operate above its NPSHR requirement at all times
and all seasons. Adequate inlet pressure must be
provided prior to booster start-up.
Even during these 10 seconds the pressure must
remain positive and be higher than the NPSHR (Net
Positive Suction Head Requirement) of the pump.
PSIG is the actual value displayed on a pressure
gauge in the system piping. PSIG is the pressure
above the atmospheric conditions. If at any time
these pressure requirements are not being met, the
motor must be de-energized immediately to prevent
permanent damage to the motor. Once the motor is
damaged, it is usually not immediately noticeable,
but progresses and results in a premature motor
failure weeks or months after the damage occurred.
Four Continuous Monitoring System Requirements
for Sealed Booster Systems.
1.
2.
39
Water Temperature: Feed water on each
booster must be continuously monitored and
not allowed to exceed the motor nameplate
maximum ambient temperature at any time. IF
THE INLET TEMPERATURE EXCEEDS THE
MOTOR NAMEPLATE MAXIMUM AMBIENT
TEMPERATURE, THE SYSTEM MUST
SHUTDOWN IMMEDIATELY TO PREVENT
PERMANENT MOTOR DAMAGE. If feed water
temperatures are expected to be above the
allowable temperature, the motor must be derated.
See Franklin’s AIM Manual Hot Water Applications
section for derating guidelines. (The high
temperature feed water derating is in addition to the
exchange to DI water derating if the motor factory fill
solution was exchanged to DI water.)
Inlet Pressure: The inlet pressure on each booster
module must be continuously monitored. It must
always be positive and higher than the NPSHR (Net
Positive Suction Head Requirement) of the pump.
A minimum of 20 PSIG (1.38 Bar) is required at all
times, except for 10 seconds or less when the motor
is starting and the system is coming up to pressure.
Motors that will be exposed to pressure in excess
of 500 psi (34.47 Bar) must undergo special high
pressure testing. Consult factory for details
and availability.
3.
Discharge Flow: The flow rate for each pump must
not be allowed to drop below the motor minimum
cooling flow requirement. IF THE MOTOR MINIMUM
COOLING FLOW REQUIREMENT IS NOT BEING
MET FOR MORE THAN 10 SECONDS, THE
SYSTEM MUST BE SHUT DOWN IMMEDIATELY
TO PREVENT PERMANENT MOTOR DAMAGE.
4.
Discharge Pressure: The discharge pressure
must be monitored to ensure that a downthrust load
toward the motor is present within 3 seconds after
start-up and continuously during operation.
IF THE MOTOR DISCHARGE PRESSURE IS NOT
ADEQUATE TO MEET THIS REQUIREMENT, THE
SYSTEM MUST BE SHUT DOWN IMMEDIATELY
TO PREVENT PERMANENT MOTOR DAMAGE.
!00,)#!4)/.
4HREE 0HASE -OTORS
6ARIABLE &REQUENCY $RIVE 3UBMERSIBLE -OTOR 2EQUIREMENTS
Franklin Electric’s three-phase, encapsulated
submersible motors can be used with variable frequency
drives (VFD) when applied within the guidelines below.
All three-phase, encapsulated submersible motors must
have the VFD sized based on the motor’s nameplate
maximum amps, not horsepower. The continuous rated
amps of the VFD must be equal to or greater than the
motor’s nameplate maximum amps or warranty will be
void.
Franklin Electric’s single-phase, 2- and 3-wire,
encapsulated submersible motors can only be used with
the appropriate Franklin constant pressure controller.
Franklin Electric’s submersible motor Application
Installation Maintenance (AIM) manual should be
checked for the latest guidelines and can be found online
at www.franklin-electric.com.
WARNING: There is a potential shock hazard from
contact with and/or touching the insulated cables
connected to the variable frequency drive output
anytime the motor has energy applied.
/UTPUT &ILTER 2EQUIREMENT 4EST
Franklin Electric has a line of VFDs that are specifically
designed for Franklin application systems. These VFDs
are used in the MonoDrive and SubDrive constant
pressure systems. Franklin drive systems have the
required additional output filtering installed; however,
the SubDrive HPX does not.
4YPES OF /UTPUT &ILTERS
A resistor-inductor-capacitor (RLC) filter has both a high
pass filter & a low pass filter section and are considered
the best practice, but a high pass reactor filter is also
acceptable.
Filters should be recommended by the drive manufacturer;
for the correct recommendations provide them with
answers to all five of the items below.
2%15)2%$ )4%-3 &/2 02/0%2 6&$ &),4%2 3):).'
(1) VFD model (2) Carrier frequency setting (3) Motor
nameplate voltage (4) Motor nameplate max amps
(5) Cable length from the drive output terminals
to the motor
)NPUT #URRENT -OTOR
/VERLOAD 0ROTECTION
./4)#%: An incoming power supply or line-side filter for
the drive does not replace the need for additional output
filters.
s -OTOR INPUT CURRENT SHOULD BE SET AT THE SYSTEMS
typical operating current when running at
nameplate rated voltage and frequency (Hz).
!N OUTPUT lLTER IS REQUIRED IF THE ANSWER IS YES
TO ONE OR BOTH OF THE ITEMS BELOW
s -OTOR OVERLOAD PROTECTION SHOULD BE SET TO TRIP AT
115% of the system’s typical operating current.
#1 - Is the VFD’s pulse width modulation (PWM) voltage
rise-time (dV/dt) more than 500 Volts per micro-second
(500 V/µ-second)?
#2 - Is the motor nameplate voltage more than 379
Volts and is the cable from drive-to-motor more than
50 ft (15.2 m)?
./4)#%
More than 99% of the drives applied on water well
submersible motors will require the purchase of
additional output filtering based on question #1.
Output filters can be expensive. However, when needed,
it is required for the motor to be considered for warranty.
Make sure this item is not overlooked when quoting
a job.
s -OTOR OVERLOAD PROTECTION MUST TRIP EQUAL TO
or faster than NEMA Class 10 motor overload
curve requirements.
-OTOR -AXIMUM ,OAD ,IMITS
s 4HE SYSTEM MUST NEVER OPERATE IN EXCESS OF THE MOTOR
nameplate maximum amps.
s /N (Z MOTORS NAMEPLATE AMPS ARE MAXIMUM
amps as these motors have a 1.0 service factor.
PWM dV/dt value can be defined as: the rate at which
voltage is changing with time or how fast the voltage
is accelerating. This information can be supplied by
the drive manufacturer or the manufacturer’s drive
specification sheet. The dV/dt value cannot be measured
with typical field equipment, even when using a true-RMS
voltage/amperage multi-meter.
40
!00,)#!4)/.
4HREE 0HASE -OTORS
6ARIABLE &REQUENCY $RIVE 3UBMERSIBLE -OTOR 2EQUIREMENTS
-OTOR /PERATING (ERTZ #OOLING
2EQUIREMENTS 5NDERLOAD
3ETTINGS
s 3TANDARD PRACTICE FOR LARGE 6&$ INSTALLATIONS IS TO LIMIT
the operation to 60 Hz max. Operating at greater than
60 Hz requires special system design considerations.
s 4HE MOTOR MUST NEVER OPERATE BELOW (Z 4HIS IS
the minimum speed required to provide correct bearing
lubrication.
s 4HE MOTORS OPERATING SPEED MUST ALWAYS OPERATE
so the minimum water flow requirements of 0.5 ft/sec
for 6-inch & 8-inch motors and 0.25 ft/sec for 4-inch
motors is supplied.
s 4HE MOTOR UNDERLOAD PROTECTION IS NORMALLY SET TO
trip at 80% of the system’s typical operating current.
However, the underload trip point must be selected
so that minimum flow requirements are always met.
3TARTING 3TOPPING 2AMP 3ETTINGS
s 4HE MOTOR MUST REACH OR PASS THE (Z OPERATING
speed within 1 second of the motor being energized.
If this does not occur, the motor bearings will be
damaged and the motor life reduced.
s 4HE BEST STOPPING METHOD IS TO TURN POWER
off followed by a natural coast to stop.
s ! CONTROLLED STOP FROM (Z TO (Z IS ALLOWED IF THE
time does not exceed 1 second.
$RIVE #ARRIER &REQUENCY
s 4HE CARRIER FREQUENCY IS SET IN THE lELD 4HE DRIVE
typically has a selectable range between 2k and
12k Hz. The higher the carrier wave frequency setting,
the greater the voltage spikes; the lower the carrier
wave frequency setting, the rougher/poorer the shape
of the power curve.
s 4HE CARRIER FREQUENCY SHOULD BE SET WITHIN THE RANGE
of 4k to 5k Hz for encapsulated submersible motors.
!PPLICATION &UNCTION 3ETTING
s )F THE 6&$ HAS A SETTING OF CENTRIFUGAL PUMP OR
propeller fan it should be used.
s #ENTRIFUGAL PUMPS AND FANS HAVE SIMILAR
load characteristics.
41
6&$ &REQUENCY OF 3TARTS
s +EEPING THE STARTS PER DAY WITHIN THE RECOMMENDED
numbers shown in the frequency of starts section of
the AIM manual provides the best system life.
However, since in-rush current is typically reduced
when used with a properly configured VFD, large
3-phase submersible motors can be started more
frequently. In all cases a minimum of 7 minutes
must be allowed between a power off and the next
restart attempt or consecutive restart attempts.
.%-! -' !BOVE 'ROUND -OTOR
3TANDARD #OMMENTS
s &RANKLIN %LECTRIC ENCAPSULATED SUBMERSIBLE MOTORS
are not declared inverter duty motors by NEMA MG1
standards. The reason is NEMA MG1 standard part
31 does not include a section covering encapsulated
winding designs.
s &RANKLIN SUBMERSIBLE MOTORS CAN BE USED WITH 6&$S
without problems or warranty concerns providing
Franklin's Application Installation Maintenance (AIM)
manual guidelines are followed. See Franklin's on-line
AIM manual for the latest guidelines.
).34!,,!4)/.
!LL -OTORS
v 3UPER 3TAINLESS $IMENSIONS
v (IGH 4HRUST $IMENSIONS
3TANDARD 7ATER 7ELL
3TANDARD 7ATER 7ELL
0.030" R
MAX
14 TOOTH 24/48"
DIAMETRAL PITCH
0.50" MIN.
FULL SPLINE
1.48"
MAX
0.030" R
MAX
1.508"
1.498"
5/16" - 24 UNF-2A
MOUNTING STUDS
1.508"
1.498"
5/16" - 24 UNF-2A
MOUNTING STUDS
0.97"
0.79"
0.161" MAX LEAD
BOSS HEIGHT
14 TOOTH 24/48"
DIAMETRAL PITCH
0.50" MIN.
FULL SPLINE
1.48"
MAX
1.09"
0.91"
0.161" MAX LEAD
BOSS HEIGHT
3.75" DIA.
3.75" DIA.
L*
L*
v $IMENSIONS
v $IMENSIONS
3TANDARD 7ATER 7ELL
3TANDARD 7ATER 7ELL
15 TOOTH 16/32"
DIAMETRAL PITCH
.94" MIN.
FULL SPLINE
3.000"
2.997"
1.0000" DIA.
0.9995"
2.875"
2.869"
0.250"
0.240"
0.75"
1/2" - 20 UNF-2B
MOUNTING HOLES
CHECK
VALVE
L*
23 TOOTH 16/32"
DIAMETRAL PITCH
5.000"
4.997"
1.69"
MIN FULL
SPLINE
4.000"
3.990"
SHAFT DIA
1.5000"
1.4990"
1.06"
0.94"
23 TOOTH 16/32"
DIAMETRAL PITCH
0.240"
5.130"
5.120"
M8 x 1.25 6G
GROUND
SCREW
7.70" DIA
MAX
L*
1.69"
MIN FULL
SPLINE
4.000"
3.990"
SHAFT DIA
1.5000"
1.4990"
1.06"
0.94"
CHECK
VALVE
WATER
WELL
MODELS
PIPE PLUG
STAINLESS
STEEL
MODELS
5.000"
4.997"
0.240"
5.130"
5.120"
CHECK
VALVE
MOUNTING HOLES
CLEARANCE FOR
5/8" BOLTS
M8 x 1.25 6G
GROUND
SCREW
7.70" DIA
MAX
L*
5.44" DIA.
6.25"
7.00"
FINNED
2.75"
FINNED
40 to 100 hp
125 to 200 hp
* Motor lengths and shipping weights are available on Franklin Electric’s web site (www.franklin-electric.com) or by
calling Franklin’s submersible hotline (800-348-2420).
42
).34!,,!4)/.
!LL -OTORS
4IGHTENING -OTOR ,EAD #ONNECTOR *AM .UT
4" Motors with Jam Nut:
15 to 20 ft-lb (20 to 27 Nm)
4" Motors with 2 Screw Clamp Plate:
35 to 45 in-lb (4.0 to 5.1 Nm)
6" Motors:
40 to 50 ft-lb (54 to 68 Nm)
8" Motors with 1-3/16" to 1-5/8" Jam Nut:
50 to 60 ft-lb (68 to 81 Nm)
8" Motors with 4 Screw Clamp Plate:
Apply increasing torque to the screws equally in a
criss-cross pattern until 80 to 90 in-lb (9.0 to 10.2
Nm) is reached.
Jam nut tightening torques recommended for field
assembly are shown. Rubber compression set within the
first few hours after assembly may reduce the jam nut
torque. This is a normal condition which does not indicate
reduced seal effectiveness. Retightening is not required,
but is permissible and recommended if original torque
was questionable.
0UMP TO -OTOR #OUPLING
0UMP TO -OTOR !SSEMBLY
Assemble coupling with non-toxic FDA approved
waterproof grease such as Mobile FM102, Texaco
CYGNUS2661, or approved equivalent. This prevents
abrasives from entering the spline area and prolongs
spline life.
After assembling the motor to the pump, torque mounting
fasteners to the following:
A motor lead assembly should not be reused. A new lead
assembly should be used whenever one is removed from
the motor, because rubber set and possible damage from
removal may prevent proper resealing of the old lead.
All motors returned for warranty consideration must
have the lead returned with the motor.
4" Pump and Motor: 10 lb-ft (14 Nm)
6" Pump and Motor: 50 lb-ft (68 Nm)
8" Pump and Motor: 120 lb-ft (163 Nm)
3HAFT (EIGHT AND &REE %ND 0LAY
Table 42
MOTOR
NORMAL
SHAFT HEIGHT
FREE END PLAY
DIMENSION
SHAFT HEIGHT
MIN.
MAX.
38.30
mm
38.05
0.010"
0.25 mm
0.045"
1.14 mm
4"
1 1/2"
38.1 mm
1.508"
1.498"
6"
2 7/8"
73.0 mm
2.875"
2.869"
73.02
mm
72.88
0.030"
0.76 mm
0.050"
1.27 mm
8" TYPE 1
4"
101.6 mm
4.000"
3.990"
101.60
mm
101.35
0.008"
0.20 mm
0.032"
0.81 mm
8" TYPE 2.1
4"
101.6 mm
4.000"
3.990"
101.60
mm
101.35
0.030"
0.76 mm
0.080"
2.03 mm
If the height, measured from the
pump-mounting surface of the
motor, is low and/or end play
exceeds the limit, the motor thrust
bearing is possibly damaged, and
should be replaced.
3UBMERSIBLE ,EADS AND #ABLES
A common question is why motor leads are smaller than
specified in Franklin’s cable charts.
The leads are considered a part of the motor and actually
are a connection between the large supply wire and the
motor winding. The motor leads are short and there is
virtually no voltage drop across the lead.
In addition, the lead assemblies operate under water,
while at least part of the supply cable must operate in
air. Lead assemblies running under water operate cooler.
43
CAUTION: Lead assemblies on submersible motors
are suitable only for use in water and may overheat
and cause failure if operated in air.
-!).4%.!.#%
!LL -OTORS
3YSTEM 4ROUBLESHOOTING
Motor Does Not Start
POSSIBLE CAUSE
CHECKING PROCEDURES
CORRECTIVE ACTION
A. No power or incorrect voltage.
Check voltage at line terminals.
The voltage must be ± 10% of rated voltage.
Contact power company if voltage is incorrect.
B. Fuses blown or circuit breakers tripped.
Check fuses for recommended size and
check for loose, dirty or corroded
connections in fuse receptacle. Check
for tripped circuit breakers.
Replace with proper fuse or reset
circuit breakers.
C. Defective pressure switch.
Check voltage at contact points. Improper
contact of switch points can cause voltage
less than line voltage.
Replace pressure switch or clean points.
D. Control box malfunction.
For detailed procedure, see pages 48-56.
Repair or replace.
E. Defective wiring.
Check for loose or corroded connections
or defective wiring
Correct faulty wiring or connections.
F. Bound pump.
Check for misalignment between pump
and motor or a sand bound pump.
Amp readings will be 3 to 6 times higher
than normal until the overload trips
Pull pump and correct problem. Run new
installation until the water clears
G. Defective cable or motor.
For detailed procedure, see pages 46 & 47.
Repair or replace.
A. Pressure switch.
Check setting on pressure switch and
examine for defects.
Reset limit or replace switch.
B. Check valve - stuck open.
Damaged or defective check valve will
not hold pressure.
Replace if defective.
C. Waterlogged tank.
Check air charge
Clean or replace.
D. Leak in system.
Check system for leaks.
Replace damaged pipes or repair leaks.
Motor Starts Too Often
44
-!).4%.!.#%
!LL -OTORS
3YSTEM 4ROUBLESHOOTING
Motor Runs Continuously
POSSIBLE CAUSE
CHECKING PROCEDURES
CORRECTIVE ACTION
A. Pressure switch.
Check switch for welded contacts.
Check switch adjustments.
Clean contacts, replace switch, or adjust setting.
B. Low water level in well.
Pump may exceed well capacity. Shut off
pump, wait for well to recover. Check
static and drawdown level from well head.
Throttle pump output or reset pump to lower level.
Do not lower if sand may clog pump.
C. Leak in system.
Check system for leaks.
Replace damaged pipes or repair leaks.
D. Worn pump.
Symptoms of worn pump are similar to
those of drop pipe leak or low water level
in well. Reduce pressure switch setting, if
pump shuts off worn parts may be the fault.
Pull pump and replace worn parts.
E. Loose coupling or broken motor shaft.
Check for loose coupling or damaged shaft.
Replace worn or damaged parts.
F. Pump screen blocked.
Check for clogged intake screen.
Clean screen and reset pump depth.
G. Check valve stuck closed.
Check operation of check valve.
Replace if defective.
H. Control box malfunction.
See pages 47-55 for single-phase.
Repair or replace.
Motor Runs But Overload Protector Trips
A. Incorrect voltage.
Using voltmeter, check the line terminals.
Voltage must be within ± 10% of rated voltage.
Contact power company if voltage is incorrect.
B. Overheated protectors.
Direct sunlight or other heat source can raise control
box temperature causing protectors to trip. The box
must not be hot to touch.
Shade box, provide ventilation or move
box away from source.
C. Defective control box.
For detailed procedures, see pages 47-55.
Repair or replace.
D. Defective motor or cable.
For detailed procedures, see pages 45 & 46.
Repair or replace.
E. Worn pump or motor.
Check running current, see tables 13, 22, 24 & 27.
Replace pump and/or motor.
45
-!).4%.!.#%
!LL -OTORS
Table 45 Preliminary Tests - All Sizes Single- and Three-Phase
TEST
PROCEDURE
WHAT IT MEANS
1. Open master breaker and disconnect all leads from control
box or pressure switch (QD type control, remove lid) to
avoid electric shock hazard and damage to the meter.
1. If the ohms value is normal (table 46), the motor is
not grounded and the cable insulation is not damaged.
2. If the ohms value is below normal, either the windings
are grounded or the cable insulation is damaged.
Check the cable at the well seal as the insulation is
sometimes damaged by being pinched.
2. Use a megohmmeter or set the scale lever to R X 100K
on an ohmmeter. Zero the meter.
Insulation
Resistance
3. Connect one meter lead to any one of the motor leads
and the other lead to the metal drop pipe. If the drop pipe is
plastic, connect the meter lead to ground.
Winding
Resistance
1. Open master breaker and disconnect all leads from control
box or pressure switch (QD type control, remove lid) to
avoid electric shock hazard and damage to the meter.
1. If all ohms values are normal (tables 13, 22, 24 & 27), the
motor windings are neither shorted nor open, and the
cable colors are correct
2. Set the scale lever to R X 1 for values under 10 ohms.
For values over 10 ohms, set the scale lever to R X 10.
hZEROv THE OHMMETER
2. If any one value is less than normal, the motor
is shorted.
3. If any one ohm value is greater than normal, the
winding or the cable is open, or there is a poor cable
joint or connection.
3. On 3-wire motors measure the resistance of yellow to black
(main winding) and yellow to red (start winding).
On 2-wire motors: measure the resistance from line-to-line.
4. If some ohms values are greater than normal and some
less on single-phase motors, the leads are mixed. See
page 46 to verify cable colors.
Three-phase motors: measure the resistance line-to-line
for all three combinations.
ATTACH THIS LEAD
TO WELL CASING OR
DISCHARGE PIPE
L1
TO
POWER
SUPPLY
{
L2
GROUND
L1
L2
POWER MUST
BE SHUT OFF
R
Y
CONNECT
THIS LEAD
TO GROUND
B
L1
L2
R
B
RED
RED
YELLOW
YELLOW
BLACK
BLACK
BLACK
YELLOW
RED
GROUND
{
TO
PUMP
TO
POWER
SUPPLY
{
GROUND
L1
L2
BLACK
YELLOW
RED
GROUND
POWER MUST
BE SHUT OFF
MEGGER
OR OHMMETER
SET AT R X 100K
FIG. 13
Y
{
TO
PUMP
OHMMETER
SET AT R X 1
FIG. 14
46
-!).4%.!.#%
!LL -OTORS
)NSULATION 2ESISTANCE 2EADINGS
Table 46 Normal ohm and Megohm Values Between All Leads and Ground
CONDITION OF MOTOR AND LEADS
OHMS VALUE
MEGOHM VALUE
A new motor (without drop cable).
200,000,000 (or more)
200.0 (or more)
A used motor which can be reinstalled in well.
10,000,000 (or more)
10.0 (or more)
2,000,000 (or more)
2.0 (or more)
500,000 - 2,000,000
0.50 - 2.0
Less than 500,000
Less than .50
MOTOR IN WELL. READINGS ARE FOR DROP CABLE PLUS MOTOR.
New motor.
Motor in good condition.
Insulation damage, locate and repair.
Insulation resistance varies very little with rating. Motors of all hp, voltage, and phase rating have similar values of
insulation resistance.
The table above is based on readings taken with a megohm meter with a 500 VDC output. Readings may vary using a lower
voltage ohmmeter, consult Franklin Electric if readings are in question.
2ESISTANCE OF $ROP #ABLE OHMS
The values below are for copper conductors. If aluminum
conductor drop cable is used, the resistance will be
higher. To determine the actual resistance of the
aluminum drop cable, divide the ohm readings from this
chart by 0.61. This chart shows total resistance of cable
from control to motor and back.
Winding Resistance Measuring
The winding resistance measured at the motor should
fall within the values in tables 13, 22, 24 & 27. When
measured through the drop cable, the resistance of
the drop cable must be subtracted from the ohmmeter
readings to get the winding resistance of the motor. See
table below.
Table 46A DC Resistance in ohms per 100 ft of Wire (Two conductors) @ 50 °F
47
AWG OR MCM WIRE SIZE (COPPER)
14
12
10
8
6
4
3
2
OHMS
0.544
0.338
0.214
0.135
0.082
0.052
0.041
0.032
1
1/0
2/0
3/0
4/0
250
300
350
400
500
600
700
0.026
0.021
0.017
0.013
0.010
0.0088
0.0073
0.0063
0.0056
0.0044
0.0037
0.0032
-!).4%.!.#%
3INGLE 0HASE -OTORS #ONTROLS
)DENTIlCATION /F #ABLES 7HEN #OLOR #ODE )S 5NKNOWN (Single-Phase 3-Wire Units)
If the colors on the individual drop cables cannot be
found with an ohmmeter, measure:
Cable 1 to Cable 2
Cable 2 to Cable 3
Cable 3 to Cable 1
Find the highest resistance reading.
The lead not used in the highest reading is the
yellow lead.
Use the yellow lead and each of the other two leads to
get two readings:
Highest is the red lead.
Lowest is the black lead.
EXAMPLE:
The ohmmeter readings were:
Cable 1 to Cable 2 - 6 ohms
Cable 2 to Cable 3 - 2 ohms
Cable 3 to Cable 1 - 4 ohms
The lead not used in the highest reading (6 ohms) was
Cable 3—Yellow
From the yellow lead, the highest reading (4 ohms) was
To Cable 1—Red
From the yellow lead, the lowest reading (2 ohms) was
To Cable 2—Black
3INGLE 0HASE #ONTROL "OXES
Checking and Repairing Procedures (Power On)
WARNING: Power must be on for these tests. Do not
touch any live parts.
A. VOLTAGE MEASUREMENTS
Step 1. Motor Off
1. Measure voltage at L1 and L2 of pressure switch
or line contactor.
2. Voltage Reading: Should be ± 10% of
motor rating.
Step 2. Motor Running
1. Measure voltage at load side of pressure switch
or line contactor with pump running.
2. Voltage Reading: Should remain the same except
for slight dip on starting. Excessive voltage
drop can be caused by loose connections, bad
contacts, ground faults, or inadequate
power supply.
3. Relay chatter is caused by low voltage or
ground faults.
B. CURRENT (AMP) MEASUREMENTS
1. Measure current on all motor leads.
2. Amp Reading: Current in red lead should
momentarily be high, then drop within one second
to values in table 13. This verifies relay or solid
state relay operation. Current in black and yellow
leads should not exceed values in table 13.
3. Relay or switch failures will cause red lead
current to remain high and overload tripping.
4. Open run capacitor(s) will cause amps to be
higher than normal in the black and yellow motor
leads and lower than normal in the red
motor lead.
5. A bound pump will cause locked rotor amps and
overloading tripping.
6. Low amps may be caused by pump running at
shutoff, worn pump, or stripped splines.
7. Failed start capacitor or open switch/relay are
indicated if the red lead current is not
momentarily high at starting.
CAUTION: The tests in this manual for components such as capacitors, relays, and QD switches should be
regarded as indicative and not as conclusive. For example, a capacitor may test good (not open, not shorted) but
may have lost some of its capacitance and may no longer be able to perform its function.
48
-!).4%.!.#%
3INGLE 0HASE -OTORS #ONTROLS
/HMMETER 4ESTS
QD, Solid State Control Box (Power Off)
A. START CAPACITOR AND RUN CAPACITOR IF
APPLICABLE (CRC)
1. Meter Setting: R x 1,000.
2. Connections: Capacitor terminals.
3. Correct meter reading: Pointer should swing
toward zero, then back to infinity.
B. Q.D. (BLUE) RELAY
Step 1. Triac Test
1. Meter setting: R x 1,000.
C. POTENTIAL (VOLTAGE) RELAY
Step 1. Coil Test
1. Meter setting: R x 1,000.
2. Connections: #2 & #5.
3. Correct meter readings:
For 115 Volt Boxes:
0.7-1.8 (700 to 1,800 ohms).
For 230 Volt Boxes:
4.5-7.0 (4,500 to 7,000 ohms).
2. Connections: Cap and B terminal.
Step 2. Contact Test
3. Correct meter reading: Infinity for all models.
1. Meter setting: R x 1.
Step 2. Coil Test
2. Connections: #1 & #2.
1. Meter Setting: R x 1.
3. Correct meter reading: Zero for all models.
2. Connections: L1 and B.
3. Correct meter reading: Zero ohms for all models.
/HMMETER 4ESTS
Integral Horsepower Control Box (Power Off)
A. OVERLOADS (Push Reset Buttons to make sure
contacts are closed.)
1. Meter Setting: R x 1.
2. Connections: Overload terminals.
3. Correct meter reading: Less than 0.5 ohms.
B. CAPACITOR (Disconnect leads from one side of
each capacitor before checking.)
1. Meter Setting: R x 1,000.
2. Connections: Capacitor terminals.
3. Correct meter reading: Pointer should swing toward
zero, then drift back to infinity, except for capacitors
with resistors which will drift back to 15,000 ohms.
C. POTENTIAL (VOLTAGE) RELAY
Step 1. Coil Test
1. Meter setting: R x 1,000.
2. Connections: #2 & #5.
Step 2. Contact Test
1. Meter Setting: R x 1.
2. Connections: #1 & #2.
3. Correct meter reading: Zero ohms for all models.
D. CONTACTOR
Step 1. Coil
1. Meter setting: R x 100
2. Connections: Coil terminals
3. Correct meter reading:
1.8-14.0 (180 to 1,400 ohms)
Step 2. Contacts
1. Meter Setting: R X 1
2. Connections: L1 & T1 or L2 & T2
3. Manually close contacts
4. Correct meter reading: Zero ohms
3. Correct meter readings: 4.5-7.0 (4,500 to 7,000
ohms) for all models.
CAUTION: The tests in this manual for components such as capacitors, relays, and QD switches should be regarded as
indicative and not as conclusive. For example, a capacitor may test good (not open, not shorted) but may have lost some
of its capacitance and may no longer be able to perform its function.
49
-!).4%.!.#%
3INGLE 0HASE -OTORS #ONTROLS
Table 49 QD Control Box Parts 60 Hz
HP
1/3
1/2
3/4
1
CONTROL BOX
MODEL NUMBER
VOLTS
QD (BLUE) RELAY
START
CAPACITOR
MFD
VOLTS
115
280 102 4915
223 415 905
275 464 125
159-191
110
230
280 103 4915
223 415 901
275 464 126
43-53
220
115
280 104 4915
223 415 906
275 464 201
250-300
125
230
280 105 4915
223 415 902
275 464 105
59-71
220
230
282 405 5015 (CRC)
223 415 912
275 464 126
43-53
220
230
280 107 4915
223 415 903
275 464 118
86-103
220
230
282 407 5015 (CRC)
223 415 913
275 464 105
59-71
220
230
280 108 4915
223 415 904
275 464 113
105-126
220
230
282 408 5015 (CRC)
223 415 914
275 464 118
86-103
220
Table 49A QD Capacitor Replacement Kits
RUN
CAPACITOR
MFD
VOLTS
156 362 101
15
370
156 362 102
23
370
156 362 102
23
370
Table 49B Overload Kits 60 Hz
CAPACITOR NUMBER
KIT
HP
VOLTS
KIT (1)
275 464 105
305 207 905
1/3
115
305 100 901
275 464 113
305 207 913
1/3
230
305 100 902
275 464 118
305 207 918
1/2
115
305 100 903
275 464 125
305 207 925
1/2
230
305 100 904
275 464 126
305 207 926
3/4
230
305 100 905
275 464 201
305 207 951
1
230
305 100 906
156 362 101
305 203 907
156 362 102
305 203 908
(1) For Control Boxes with model numbers that end with 4915.
Table 49C QD Relay Replacement Kits
QD RELAY NUMBER
KIT
223 415 901
305 101 901
223 415 902
305 101 902
223 415 903
305 101 903
223 415 904
305 101 904
223 415 905
305 101 905
223 415 906
305 101 906
223 415 912 (CRC)
305 105 901
223 415 913 (CRC)
305 105 902
223 415 914 (CRC)
305 105 903
FOOTNOTES:
(1) Control boxes supplied with QD Relays are designed to operate on 230-volt systems. For 208-volt systems
or where line voltage is between 200 volts and 210 volts use the next larger cable size, or use a boost transformer
to raise the voltage.
(2) Voltage relays kits for 115-volts (305 102 901) and 230-volts (305 102 902) will replace current, voltage or QD
Relays, and solid state switches.
50
-!).4%.!.#%
3INGLE 0HASE -OTORS #ONTROLS
Table 50 Integral Horsepower Control Box Parts 60 Hz
MOTOR
SIZE
4"
MOTOR
RATING HP
1 - 1.5
STANDARD
CAPACITORS
CONTROL BOX (1)
MODEL NO.
PART NO. (2)
MFD.
VOLTS
QTY.
OVERLOAD (2)
PART NO.
RELAY (3)
PART NO.
282 300 8110
(See Note 5)
275 464 113 S
155 328 102 R
105-126
10
220
370
1
1
275 411 107
155 031 102
282 300 8110
(See Note 5)
275 464 113 S
155 328 101 R
105-126
15
220
370
1
1
275 411 114 S
275 411 113 M
155 031 102
282 300 8610
275 464 113 S
155 328 101 R
105-126
15
220
370
1
1
None
(See Note 4)
155 031 102
4"
2
STANDARD
282 301 8110
275 464 113 S
155 328 103 R
105-126
20
220
370
1
1
275 411 117 S
275 411 113 M
155 031 102
4"
2
DELUXE
282 301 8310
275 464 113 S
155 328 103 R
105-126
20
220
370
1
1
275 411 117 S
275 411 113 M
155 031 102
4"
3
STANDARD
282 302 8110
275 463 123 S
155 327 109 R
208-250
45
220
370
1
1
275 411 118 S
275 411 115 M
155 031 102
4"
3
DELUXE
282 302 8310
275 463 123 S
155 327 109 R
208-250
45
220
370
1
1
275 411 118 S
275 411 115 M
155 031 102
4" & 6"
5
STANDARD
282 113 8110
275 468 119 S
155 327 114 R
270-324
40
330
370
1
2
275 411 119 S
275 406 102 M
155 031 601
4" & 6"
5
DELUXE
282 113 9310
275 468 119 S
155 327 114 R
270-324
40
330
370
1
2
275 411 119 S
275 406 102 M
155 031 601
6"
7.5
STANDARD
282 201 9210
275 468 119 S
275 468 118 S
155 327 109 R
270-324
216-259
45
330
330
370
1
1
1
275 411 102 S
275 406 122 M
155 031 601
6"
7.5
DELUXE
282 201 9310
275 468 119 S
275 468 118 S
155 327 109 R
270-324
216-259
45
330
330
370
1
1
1
275 411 102 S
275 406 121 M
155 031 601
6"
10
STANDARD
282 202 9210
275 468 119 S
275468 120 S
155 327 102 R
270-324
350-420
35
330
330
370
1
1
2
275 406 103 S
155 409 101 M
155 031 601
282 202 9230
130-154
216-259
270-324
35
330
330
330
370
1
1
1
2
155 031 601
6"
275 463 120 S
275 468 118 S
275 468 119 S
155 327 102 R
275 406 103 S
10
STANDARD
282 202 9310
275 468 119 S
275468 120 S
155 327 102 R
270-324
350-420
35
330
330
370
1
1
2
282 202 9330
275 463 120 S
275 468 118 S
275 468 119 S
155 327 102 R
130-154
216-259
270-324
35
330
330
330
370
1
1
1
2
155 409 101 M
350-420
45
330
370
2
3
CONTACTOR (2)
PART NO.
155 325 102 L
155 325 102 L
155 326 101 L
155 326 102 L
155 409 101 M
275 406 103 S
155 409 101 M
155 031 601
155 326 102 L
275 406 103 S
155 031 601
155 326 102 L
275 406 103 S
155 409 102 M
155 031 601
155 429 101 L
275 406 103 S
155 031 601
155 429 101 L
155 031 601
2 required
155 429 101 L
6"
10
DELUXE
6"
10
DELUXE
6"
15
DELUXE
282 203 9310
275 468 120 S
155 327 109 R
6"
15
DELUXE
282 203 9330
275 463 122 S
275 468 119 S
155 327 109 R
161-193
270-324
45
330
330
370
1
2
3
155 409 102 M
6"
15
X-LARGE
282 203 9621
275 468 120 S
155 327 109 R
350-420
45
330
370
2
3
275 406 103 S
155 409 102 M
FOOTNOTES:
(1) Lightning arrestors 150 814 902 are suitable for all control boxes.
(2) S = Start, M = Main, L = Line, R = Run
Deluxe = Control box with line contactor.
(3) For 208-volt systems or where line voltage is between 200 volts and 210 volts, a low voltage relay is required. On 3
hp and smaller control boxes use relay part 155 031 103 in place of 155 031 102 and use the next larger cable size
than specified in the 230-volt table. On 5 hp and larger use relay 155 031 602 in place of 155 031 601 and next
larger wire. Boost transformers per page 15 are an alternative to special relays and cable.
(4) Control box model 282 300 8610 is designed for use with motors having internal overload protectors. If used with a
1.5 hp motor manufactured prior to date code 06H18, Overload/Capacitor Kit 305 388 901 is required.
(5) Control box model 282 300 8110 with date code 11C19 (March 2011) and newer contain 15 MFD run capacitor
and both start and run overloads. This box is designed for use with any Franklin 1.5 hp motor.
51
-!).4%.!.#%
3INGLE 0HASE -OTORS #ONTROLS
Table 51 Integral hp Capacitor Replacement Kits
CAPACITOR NUMBER
KIT
275 463 120
305 206 920
275 463 122
305 206 922
275 463 123
305 206 923
275 464 113
305 207 913
275 468 118
305 208 918
275 468 119
305 208 919
275 468 120
305 208 920
155 327 101
305 203 901
155 327 102
305 203 902
155 327 109
305 203 909
155 327 114
305 203 914
155 328 101
305 204 901
155 328 102
305 204 902
155 328 103
305 204 903
Table 51A Integral hp Overload Replacement Kits
OVERLOAD NUMBER
KIT
275 406 102
305 214 902
275 406 103
305 214 903
275 406 121
305 214 921
275 406 122
305 214 922
275 411 102
305 215 902
275 411 107
305 215 907
275 411 108
305 215 908
275 411 113
305 215 913
275 411 114
305 215 914
275 411 115
305 215 915
275 411 117
305 215 917
275 411 118
305 215 918
275 411 119
305 215 919
Table 51B Integral hp Voltage Relay Replacement Kits
RELAY NUMBER
KIT
155 031 102
305 213 902
155 031 103
305 213 903
155 031 601
305 213 961
155 031 602
305 213 962
Table 51C Integral hp Contactor Replacement Kits
CONTACTOR
KIT
155 325 102
305 226 902
155 326 101
305 347 903
155 326 102
305 347 902
155 429 101
305 347 901
FOOTNOTES:
(1)
The following kit number changes were made for number consistency purposes only.
Parts in the kit did not change.
305 206 922 was 305 206 912
305 206 923 was 305 206 911
305 213 962 was 305 213 904
305 226 902 was 305 226 901
52
-!).4%.!.#%
3INGLE 0HASE -OTORS #ONTROLS
#ONTROL "OX 7IRING $IAGRAMS
GND
QD RELAY
BLUE
YELLOW
Y
(MOTOR LEADS)
ORANGE
R (START)
BLUE
L1
RED
BLACK
53
Y
(MOTOR LEADS)
L1
QD RELAY
CAP
B
L2
1/3 - 1 hp QD RELAY
280 10_ 4915
Sixth digit depends on hp
(LINE LEADS)
RED
B (MAIN)
GREEN
YELLOW
R (START)
L2
(LINE LEADS)
BLUE
GREEN
START
CAPACITOR
B (MAIN)
CAPACITOR
RED
L1
BLACK
B
RUN
CAPACITOR
GREEN
GND
GND
ORANGE
CAP
L1
GND
GREEN
1/2 - 1 hp CRC QD RELAY
282 40_ 5015
Sixth digit depends on hp
-!).4%.!.#%
3INGLE 0HASE -OTORS #ONTROLS
START CAPACITOR
RUN CAPACITOR
BLK
BLK
RED
ORG
YEL
5
RELAY
GROUND
LEAD
L1
BLK
RED
RED
2
YEL
1
YEL BLK RED
L2
YEL
BLK
LINE POWER
FROM TWO POLE
FUSED SWITCH OR
CIRCUIT BREAKER,
AND OTHER CONTROL
IF USED.
3
BLU
1
2
OVERLOAD
GROUND TO
LEAD
MOTOR
1 - 1.5 hp
282 300 8110
(Date Codes 11C19 & Older)
START CAPACITOR
RUN CAPACITOR
RUN CAPACITOR
START CAPACITOR
BLK
RED
BLK
BLK
ORG
RED
ORG
5
YEL
2
RED
RELAY
1
YEL
5
RELAY
L1
GROUND
LEAD
MAIN
OVERLOAD
BLK
1
3
LINE POWER
FROM TWO POLE
FUSED SWITCH OR
CIRCUIT BREAKER,
AND OTHER CONTROL
IF USED.
BLK
1 3
BLK
START
OVERLOAD
1 - 1.5 hp
282 300 8110
(Date Codes 11C19 & Newer)
GROUND
LEAD
L1
RED
BLK
BLK
YEL
GROUND
LEAD
YEL BLK RED
YEL
BLU
LINE POWER
FROM TWO POLE
FUSED SWITCH OR
CIRCUIT BREAKER,
AND OTHER CONTROL
IF USED.
L2
RED
2
RED
YEL
1
YEL BLK RED
L2
YEL
BLK
BLK
GROUND TO
MOTOR
LEAD
TO
MOTOR
1 - 1.5 hp
282 300 8610
54
-!).4%.!.#%
3INGLE 0HASE -OTORS #ONTROLS
START CAPACITOR
RUN CAPACITOR
START CAPACITOR
RUN CAPACITOR
BLK
BLK
L2
L1
ORG
T1
YEL
2
RED
ORG
YEL
T2
RELAY
1
BLK
RED
YEL
COIL
5
BLK
YEL
LINE
CONTACTOR
BLK
RED
YEL
5
RELAY
RED
2
1
BLU
BLK
YEL
LINE POWER
FROM TWO POLE
FUSED SWITCH OR
CIRCUIT BREAKER,
AND OTHER CONTROL
IF USED.
1
MAIN
OVERLOAD
BLK
1 3
BLK
3
SW L1
GROUND
LEAD
GROUND
LEAD
START
OVERLOAD
TO
MOTOR
LINE
POWER
FROM
TWO POLE
FUSED
SWITCH
OR
CIRCUIT
BREAKER
TO
PRESSURE
OR OTHER
CONTROL
SWITCH
2 hp STANDARD
282 301 8110
BLK
YEL BLK RED
L2
3 1
1
GROUND
LEAD
3
START
OVERLOAD
MAIN OVERLOAD
TO
MOTOR
2 hp DELUXE
282 301 8310
START CAPACITOR
RUN CAPACITOR
RED
YEL
BLK
YEL BLK RED
L2
BLU
L1
GROUND
LEAD
RED
YEL
BLK
BLK
START CAPACITOR
RUN CAPACITOR
BLK
BLK
L2
L1
BLK
RED
ORG
T1
ORG
YEL
T2
YEL
RELAY
YEL
GROUND
LEAD
BLK
BLU
BLK
1
1
2
2
BLK
START
OVERLOAD
3 hp STANDARD
282 302 8110
55
RED
YEL BLK RED
YEL
GROUND
LEAD
TO
MOTOR
LINE
POWER
FROM
TWO POLE
FUSED
SWITCH
OR
CIRCUIT
BREAKER
TO
PRESSURE
OR OTHER
CONTROL
SWITCH
SW L1
L2
YEL BLK RED
BLU
L2
BLK
YEL
L1
GROUND
LEAD
RED
2
RED
1
BLK
BLK
BLK
RED
2
MAIN
OVERLOAD
YEL
5
RELAY
LINE POWER
FROM TWO POLE
FUSED SWITCH OR
CIRCUIT BREAKER,
AND OTHER CONTROL
IF USED.
BLK
RED
YEL
COIL
5
1
BLK
YEL
LINE
CONTACTOR
2 1
MAIN OVERLOAD
3 hp DELUXE
282 302 8310
1 2
GROUND
LEAD
START
TO
OVERLOAD
MOTOR
-!).4%.!.#%
3INGLE 0HASE -OTORS #ONTROLS
START CAPACITOR
START CAPACITOR
BLK
BLK
RUN CAPACITOR
RUN CAPACITOR
BLK
BLK
RED
BLK
RED
RED
T1
L1
YEL
5
BLK
BLK
RED
2
LINE
CONTACTOR
COIL
COIL
BLK
RELAY
1
T2
L2
YEL
YEL
5
YEL
YEL
ORG
ORG
BLK
RED
RELAY
L1
YEL
L2
GROUND
LEAD
RED
BLK
L1
SW
L2
BLK
RED
YEL
BLK
RED
YEL
GROUND
LEAD
RED
2
1
YEL
RED
BLK
BLK
1
2
2
1
START
OVERLOAD
MAIN OVERLOAD
GROUND TO
LEAD
MOTOR
LINE
POWER
FROM
TWO POLE
FUSED
SWITCH
OR
CIRCUIT
BREAKER
5 hp STANDARD
282 113 8110
TO
PRESSURE
OR OTHER
CONTROL
SWITCH
BLK
BLU
BLU
LINE POWER
FROM TWO POLE
FUSED SWITCH OR
CIRCUIT BREAKER,
AND OTHER CONTROL
IF USED.
BLK
YEL
1
2
1
2
START
OVERLOAD
MAIN OVERLOAD
GROUND TO
LEAD
MOTOR
5 hp DELUXE
282 113 8310 or 282 113 9310
START CAPACITOR
START CAPACITOR
ORG
BLK
RUN CAPACITOR
BLK
START CAPACITOR
BLK
BLK
BLK
START CAPACITOR
RED
RED
ORG
YEL
RELAY
ORG
1
T1
L1
RED
YEL
5
ORG
2
LINE
CONTACTOR
COIL
COIL
YEL
5
YEL
T2
L2
RUN CAPACITOR
BLK
YEL
RELAY
1
RED
2
BLK
SURGE
ARRESTOR
YEL
L2
SW L1
GROUND
LEAD
BLK
BLK
3
1
1
2
MAIN OVERLOAD
START
OVERLOAD
7.5 hp STANDARD
282 201 9210
GROUND
LEAD
TO
MOTOR
LINE
POWER
FROM
TWO POLE
FUSED
SWITCH
OR
CIRCUIT
BREAKER
L2
YEL
RED
YEL
RED
BLK
RED
BLK
YEL
BLU
LINE POWER
FROM TWO POLE
FUSED SWITCH OR
CIRCUIT BREAKER,
AND OTHER CONTROL
IF USED.
L1
RED
BLK
BLU
GROUND
LEAD
BLK
YEL
SURGE
ARRESTOR
TO
PRESSURE
OR OTHER
CONTROL
SWITCH
2
3
1
1
BLK
BLK
MAIN
OVERLOAD
START
OVERLOAD
GROUND
LEAD
TO
MOTOR
7.5 hp DELUXE
282 201 9310
56
-!).4%.!.#%
3INGLE 0HASE -OTORS #ONTROLS
START CAPACITOR
START CAPACITOR
START CAPACITOR
BLK
BLK
ORG
ORG
BLK
ORG
BLK
ORG
START CAPACITOR
BLK
START CAPACITOR
RED
RED
RED
BLK
RED
RUN CAPACITOR
YEL
YEL
T2
L2
LINE
CONTACTOR
BLK
BLK
COIL
COIL
BLK
YEL
5
RED
2
RELAY
1
BLK
RED
YEL
RED
RED
GROUND
LEAD
1
2
MAIN
OVERLOAD
GROUND
LEAD
START
OVERLOAD
TO
MOTOR
LINE
POWER
FROM
TWO POLE
FUSED
SWITCH
OR
CIRCUIT
BREAKER
10 hp STANDARD
282 202 9210 or 282 202 9230
RUN CAPACITOR
G
RED
L2
YEL
BLK
TO
PRESSURE
OR OTHER
CONTROL
SWITCH
1
MAIN
OVERLOAD
START
OVERLOAD
GROUND TO
LEAD
MOTOR
RUN CAPACITOR
BLK
RED
RED
RED
T2
COIL
SURGE
ARRESTOR
COIL
T2
1
2
2
LINE CONTACTOR
L1
COIL
T1
YEL
5
ORG
BLK
T1
L1
BLK
COIL
1
5
RELAY
RELAY
L2
YEL
BLK
5
YEL
L2
BLK
YEL
BLK
2
START CAPACITOR
BLK
BLK
OR
L1
SW
10 hp DELUXE
282 202 9230 or 282 202 9330
START CAPACITOR
BLK
SW
BLK
BLK
BLK
START CAPACITOR
SURGE
ARRESTOR
YEL
BLK
LINE POWER
FROM TWO POLE
FUSED SWITCH OR
CIRCUIT BREAKER,
AND OTHER CONTROL
IF USED.
YEL
L2
BLK
L1
RED
2
YEL
SURGE
ARRESTOR
GROUND
LEAD
YEL
5
ORG
1
BLK
T1
L1
RELAY
ORG
RUN CAPACITOR
BLK
BLK
BLK
START CAPACITOR
RELAY
1
RED
2
L2
L1
GROUND
LEAD
SURGE
ARRESTOR
RED
SW
GROUND
LEAD
YEL
BLK
1
TO
PRESSURE
OR OTHER
CONTROL
SWITCH
MAIN
OVERLOAD
BLK
2
START
OVERLOAD
GROUND TO
LEAD
MOTOR
15 hp DELUXE
282 203 9310 or 282 203 9330
57
B
R
Y
RED
L2
BLK
BLK
LINE
POWER
FROM
TWO POLE
FUSED
SWITCH
OR
CIRCUIT
BREAKER
L1
SW
SW SW
LINE
POWER
FROM
TWO POLE
FUSED
SWITCH
OR
CIRCUIT
BREAKER
1
2
TO
PRESSURE
OR OTHER
CONTROL
SWITCH
MAIN
OVERLOAD
START
OVERLOAD
15 hp X-LARGE
282 203 9621
GROUND
LEAD
TO
MOTOR
-!).4%.!.#%
%LECTRONIC 0RODUCTS
Pumptec-Plus
Pumptec-Plus is a pump/motor protection device designed to work on any 230 V single-phase induction motor (PSC,
CSCR, CSIR, and split phase) ranging in size from 1/2 to 5 horsepower. Pumptec-Plus uses a micro-computer to
continuously monitor motor power and line voltage to provide protection against dry well, water logged tank, high and
low voltage and mud or sand clogging.
Pumptec-Plus – Troubleshooting
During Installation
SYMPTOM
POSSIBLE CAUSE
SOLUTION
Unit Appears Dead
(No Lights)
No Power to Unit
Check wiring. Power supply voltage should be applied to L1 and L2 terminals of the
Pumptec-Plus. In some installations the pressure switch or other control devices is wired
to the input of the Pumptec-Plus. Make sure this switch is closed.
Unit Needs to Be Calibrated
Pumptec-Plus is calibrated at the factory so that it will overload on most pump systems
when the unit is first installed. This overload condition is a reminder that the PumptecPlus unit requires calibration before use. See step 7 of the installation instructions.
Miscalibrated
Pumptec-Plus should be calibrated on a full recovery well with the maximum water flow.
Flow restrictors are not recommended.
2-Wire Motor
Step C of the calibration instructions indicate that a flashing green light condition will
occur 2 to 3 seconds after taking the SNAPSHOT of the motor load. On some two-wire
motors the yellow light will flash instead of the green light. Press and release the reset
button. The green should start flashing.
Flashing Yellow Light
Flashing Yellow Light
During Calibration
Power Interruption
During the installation of Pumptec-Plus power may be switched on and off several times.
If power is cycled more than four times within a minute Pumptec-Plus will trip on rapid
cycle. Press and release the reset button to restart the unit.
Float Switch
A bobbing float switch may cause the unit to detect a rapid cycle condition on any motor
or an overload condition on two-wire motors. Try to reduce water splashing or use a
different switch.
Flashing Red and
Yellow Lights
High Line Voltage
Flashing Red Light
Unloaded Generator
Low Line Voltage
The line voltage is over 253 volts. Check line voltage. Report high line voltage to the
power company.
If you are using a generator the line voltage may become too high when the generator
unloads. Pumptec-Plus will not allow the motor to turn on again until the line voltage
returns to normal. Overvoltage trips will also occur if line frequency drops too far
below 60 Hz.
The line voltage is below 207 volts. Check line voltage.
Loose Connections
Check for loose connections which may cause voltage drops.
Loaded Generator
If you are using a generator the line voltage may become too low when the generator
loads. Pumptec-Plus will trip on undervoltage if the generator voltage drops below 207
volts for more than 2.5 seconds. Undervoltage trips will also occur if the line frequency
rises too far above 60 Hz.
Solid Red Light
58
-!).4%.!.#%
%LECTRONIC 0RODUCTS
Pumptec-Plus
Pumptec-Plus - Troubleshooting
SYMPTOM
After Installation
POSSIBLE CAUSE
SOLUTION
Dry Well
Wait for the automatic restart timer to time out. During the time out period the well should
recover and fill with water. If the automatic reset timer is set to the manual position, then the
reset button must be pressed to reactivate the unit.
Blocked Intake
Solid Yellow Light
Blocked Discharge
Remove blockage in plumbing.
Check Valve Stuck
Replace check valve.
Broken Shaft
Replace broken parts.
Severe Rapid Cycling
Worn Pump
Yellow Flashing Light
Float Switch
A bobbing float switch can cause two-wire motors to stall. Arrange plumbing to avoid
splashing water. Replace float switch.
Ground Fault
Check insulation resistance on motor and control box cable.
Loose Connections
High Line Voltage
Rapid Cycle
The line voltage is below 207 volts. Pumptec-Plus will try to restart the motor every two
minutes until line voltage is normal.
Check for excessive voltage drops in the system electrical connections (i.e. circuit breakers,
fuse clips, pressure switch, and Pumptec-Plus L1 and L2 terminals).
Repair connections.
The line voltage is over 253 volts. Check line voltage. Report high line voltage to the
power company.
The most common cause for the rapid cycle condition is a waterlogged tank. Check for a
ruptured bladder in the water tank. Check the air volume control or snifter valve for proper
operation. Check setting on the pressure switch and examine for defects.
Leaky Well System
Replace damaged pipes or repair leaks.
Stuck Check Valve
Failed valve will not hold pressure. Replace valve.
Float Switch
59
Replace worn pump parts and recalibrate.
Repair or replace motor. Pump may be sand or mud locked.
Solid Red Light
Flashing Red and
Yellow Lights
Machine gun rapid cycling can cause an underload condition. See flashing red and yellow
lights section below.
Stalled Motor
Low Line Voltage
Flashing Red Light
Clear or replace pump intake screen.
Press and release the reset button to restart the unit. A bobbing float switch may cause the
unit to detect a rapid cycle condition on any motor or an overload condition on 2-wire
motors. Try to reduce water splashing or use a different switch.
-!).4%.!.#%
%LECTRONIC 0RODUCTS
1$ 0UMPTEC AND 0UMPTEC
QD Pumptec and Pumptec are load sensing devices that monitor the load on submersible pumps/motors. If the load
drops below a preset level for a minimum of 4 seconds the QD Pumptec or the Pumptec will shut off the motor.
The QD Pumptec is designed and calibrated expressly for use on Franklin Electric 230 V 3-wire motors (1/3 to 1 hp.)
The QD Pumptec must be installed in QD relay boxes.
The Pumptec is designed for use on Franklin Electric 2- and 3-wire motors (1/3 to 1.5 hp) 115 and 230 V. The Pumptec
is not designed for jet pumps.
QD Pumptec & Pumptec – Troubleshooting
SYMPTOM
CHECKS OR SOLUTION
A. Is the voltage less than 90% of nameplate rating?
B. Are the pump and motor correctly matched?
If the QD Pumptec or Pumptec trips in about
4 seconds with some water delivery.
C. Is the QD Pumptec or Pumptec wired correctly? For the Pumptec check the wiring
diagram and pay special attention to the positioning of the power lead
(230 V or 115 V).
D. For QD Pumptec is your system 230 V 60 Hz or 220 V 50 Hz?
A. The pump may be airlocked. If there ia a check valve on top of the pump, put another
section of pipe between the pump and the check valve.
If the QD Pumptec or Pumptec trips in about
4 seconds with no water delivery.
B. The pump may be out of water.
C. Check the valve settings. The pump may be dead-heading.
D. Pump or motor shaft may be broken.
E. Motor overload may be tripped. Check the motor current (amperage).
If the QD Pumptec or Pumptec will not timeout
and reset.
A. Check switch position on side of circuit board on Pumptec. QD Pumptec check timer
position on top/front of unit. Make sure the switch is not between settings.
B. If the reset time switch is set to manual reset (position 0), QD Pumptec and Pumptec
will not reset (turn power off for 5 sec. then back on to reset).
A. Check voltage.
B. Check wiring.
If your pump/motor will not run at all.
C. Remove the QD Pumptec from the control box. Reconnect wires in box to original
state. If motor does not run the problem is not QD Pumptec. Bypass Pumptec by
connecting L2 and motor lead with jumper. Motor should run. If not, the problem is
not Pumptec.
D. On Pumptec only check that Pumptec is installed between the control switch and
the motor.
A. Be sure you have a Franklin motor.
B. Check wiring connections. On Pumptec is lead power (230 V or 115 V) connected to
correct terminal? Is motor lead connected to correct terminal?
C. Check for ground fault in the motor and excessive friction in the pump.
If your QD Pumptec or Pumptec will not trip
when the pump breaks suction.
$ 4HE WELL MAY BE hGULPINGv ENOUGH WATER TO KEEP QD Pumptec or Pumptec from
tripping. It may be necessary to adjust the QD Pumptec or the Pumptec for these
extreme applications. Call the Franklin Electric Service Hotline at 800-348-2420
for information.
E. On Pumptec applications does the control box have a run capacitor? If so, Pumptec
will not trip. (Except for Franklin 1.5 hp motors).
A. Check for low voltage.
If your QD Pumptec or Pumptec chatters
when running.
B. Check for waterlogged tank. Rapid cycling for any reason can cause the QD Pumptec
or the Pumptec relay to chatter.
C. On Pumptec make sure the L2 and motor wires are installed correctly. If they are
reversed, the unit can chatter.
60
-!).4%.!.#%
%LECTRONIC 0RODUCTS
3UB$RIVE7 -ONO$RIVE -ONO$RIVE 84
The Franklin Electric SubDrive/MonoDrive Constant Pressure controller is a variable-speed drive that delivers water
at a constant pressure.
WARNING: Serious or fatal electrical shock may result from failure to connect the motor, SubDrive/MonoDrive
Controller, metal plumbing and all other metal near the motor or cable to the power supply ground terminal using
wire no smaller than motor cable wires. To reduce the risk of electrical shock, disconnect power before working on
or around the water system. Capacitors inside the SubDrive/MonoDrive Controller can still hold a lethal voltage even
after power has been removed. Allow 10 minutes for dangerous internal voltage to discharge. Do not use motor in
swimming areas.
61
-!).4%.!.#%
%LECTRONIC 0RODUCTS
3UB$RIVE7 -ONO$RIVE -ONO$RIVE 84
SubDrive/MonoDrive Troubleshooting
3HOULD AN APPLICATION OR SYSTEM PROBLEM OCCUR BUILT IN DIAGNOSTICS WILL PROTECT THE SYSTEM 4HE h&!5,4v LIGHT OR DIGITAL
display on the front of the SubDrive/MonoDrive Controller will flash a given number of times or display a number
indicating the nature of the fault. In some cases, the system will shut itself off until corrective action is taken. Fault
codes and their corrective actions are listed below. See SubDrive/MonoDrive Installation Manual for installation data.
NUMBER OF
FLASHES OR
DIGITAL DISPLAY
1
FAULT
MOTOR
UNDERLOAD
POSSIBLE CAUSE
CORRECTIVE ACTION
- Overpumped well
- Broken shaft or coupling
- Blocked screen, worn pump
- Air/gas locked pump
- SubDrive not set properly for
pump end
- Frequency near maximum with less than 65% of expected load, 42% if
$)0 IS hONv
- System is drawing down to pump inlet (out of water)
(IGH STATIC LIGHT LOADING PUMP RESET $)0 SWITCH TO hONv FOR LESS
sensitivity if not out of water
- Check pump rotation (SubDrive only) reconnect if necessary for proper
rotation
- Air/gas locked pump - if possible, set deeper in well to reduce
- Verify DIP switches are set properly
- Low line voltage
- Misconnected input leads
- Line voltage low, less than approximately 150 VAC (normal operating
range = 190 to 260 VAC)
- Check incoming power connections and correct or tighten if necessary
- Correct incoming voltage - check circuit breaker or fuses, contact
power company
2
UNDERVOLTAGE
3
LOCKED
PUMP
- Motor and/or pump misalignment
- Dragging motor and/or pump
- Abrasives in pump
- Amperage above SFL at 10 Hz
- Remove and repair or replace as required
INCORRECTLY
WIRED
- MonoDrive only
- Wrong resistance values on main
and start
- Wrong resistance on DC test at start
- Check wiring, check motor size and DIP switch setting, adjust or repair
as needed
OPEN
CIRCUIT
- Loose connection
- Defective motor or drop cable
- Wrong motor
- Open reading on DC test at start.
- Check drop cable and motor resistance, tighten output connections, repair
OR REPLACE AS NECESSARY USE hDRYv MOTOR TO CHECK DRIVE FUNCTIONS IF DRIVE
will not run and exhibits underload fault replace drive
SHORT
CIRCUIT
- When fault is indicated immediately
after power-up, short circuit due to
loose connection, defective cable,
splice or motor
- Amperage exceeded 50 amps on DC test at start or max amps during
running
- Incorrect output wiring, phase to phase short, phase to ground short in
wiring or motor
- If fault is present after resetting and removing motor leads, replace drive
- When fault is indicated while motor
is running, over current due to
loose debris trapped in pump
- Check pump
- High ambient temperature
- Direct sunlight
- Obstruction of airflow
- Drive heat sink has exceeded max rated temperature, needs to drop
below 85 °C to restart
- Fan blocked or inoperable, ambient above 125 °F, direct sunlight, air flow
blocked
- Replace fan or relocate drive as necessary
- Improper pre-charge
- Valve closing too fast
- Pressure setting too close to relief
valve rating
- Reset the pre-charge pressure to 70% of sensor setting. Reduce pressure
setting well below relief valve rating. Use next size larger pressure tank.
- Verify valve operation is within manufacturer’s specifications.
- Reduce system pressure setting to a value less than pressure relief rating.
- A fault was found internal to drive
- Unit may require replacement. Contact your supplier.
- Wrong hp/voltage
- Internal fault
- Verify motor hp and voltage
- Unit may require replacement. Contact your supplier.
4
(MonoDrive &
MonoDriveXT only)
5
6
OVER CURRENT
7
8
(SubDrive300 only)
RAPID
9
(SubDrive2W only)
OVERHEATED
DRIVE
OVER
PRESSURE
INTERNAL FAULT
OVER RANGE
(Values outside normal
operating range)
62
-!).4%.!.#%
%LECTRONIC 0RODUCTS
3UB-ONITOR
SubMonitor Troubleshooting
FAULT MESSAGE
SF Amps Set Too High
Phase Reversal
PROBLEM/CONDITION
SF Amps setting above 359 Amps.
Motor SF Amps not entered.
Reversed incoming voltage phase sequence.
Incoming power problem.
Normal line current.
Wrong SF Max Amps setting.
Low line current.
Over pumping well.
Clogged pump intake.
Closed valve.
Loose pump impeller.
Broken shaft or coupling.
Phase loss.
Normal line current.
Wrong SF Max Amps setting.
High line current.
High or low line voltage.
Ground fault.
Pump or motor dragging.
Motor stalled or bound pump.
Motor temperature sensor has detected excess
motor temperature.
High or low line voltage.
Motor is overloaded.
Excessive current unbalance.
Poor motor cooling.
High water temperature.
Excessive electrical noise
(VFD in close proximity).
Current difference between any two legs
exceeds programmed setting.
Phase loss.
Unbalanced power supply.
Open Delta transformer.
Line voltage exceeds programmed setting.
Unstable power supply.
Line voltage below programmed setting.
Poor connection in motor power circuit.
Unstable or weak power supply.
Power has been interrupted too many times in a
10 second period.
Chattering contacts.
Loose connections in motor power circuit.
Arcing contacts.
Underload
Overload
Overheat
Unbalance
Overvoltage
Undervoltage
False Starts
63
POSSIBLE CAUSE
Continued on next page
-!).4%.!.#%
%LECTRONIC 0RODUCTS
3UBTROL 0LUS /BSOLETE
3EE 3UB-ONITOR
Subtrol-Plus - Troubleshooting After Installation
SYMPTOM
Subtrol-Plus Dead
POSSIBLE CAUSE OR SOLUTION
When the Subtrol-Plus reset button is depressed and released, all indicator lights should flash. If line voltage is
correct at the Subtrol-Plus L1, L2, L3 terminals and the reset button does not cause lights to flash, Subtrol-Plus
receiver is malfunctioning.
Green Off Time
Light Flashes
The green light will flash and not allow operation unless both sensor coils are plugged into the receiver. If both are
properly connected and it still flashes, the sensor coil or the receiver is faulty. An ohmmeter check between the two
center terminals of each sensor coil connected should read less than 1 ohm, or coil is faulty. If both coils check good,
receiver is faulty.
Green Off Time
Light On
The green light is on and the Subtrol-Plus requires the specified off time before the pump can be restarted after
having been turned off. If the green light is on except as described, the receiver is faulty. Note that a power
interruption when the motor is running will initiate the delay function.
Overheat Light On
This is a normal protective function which turns off the pump when the motor reaches maximum safe temperatures.
Check that amps are within the nameplate maximum on all three lines, and that the motor has proper water flow past
it. If overheat trip occurs without apparent motor overheating, it may be the result of an arcing connection somewhere
in the circuit or extreme noise interference on the power lines. Check with the power company or Franklin Electric.
A true motor overheat trip will require at least five minutes for a motor started cold. If trips do not conform to this
characteristic, suspect arcing connections, power line noise, ground fault, or SCR variable speed control equipment.
Overload Light On
This is a normal protective function, protecting against an overload or locked pump. Check the amps in all lines
through a complete pumping cycle, and monitor whether low or unbalanced voltage may be causing high amps at
particular times. If overload trip occurs without high amps, it may be caused by a faulty rating insert, receiver, or
sensor coil. Recheck that the insert rating matches the motor. If it is correct, carefully remove it from the receiver by
alternately lifting sides with a knife blade or thin screwdriver, and make sure it has no pins bent over. If the insert is
correct and its pins are okay, replace receiver and/or sensor coils.
This is a normal protective function.
A. Make sure the rating insert is correct for the motor.
Underload Light On
B. Adjusting the underload setting as described to allow the desired range of operating conditions. Note that a
DECREASE in underload setting is required to allow loading without trip.
C. Check for drop in amps and delivery just before trip, indicating pump breaking suction, and for unbalanced
line current.
D. With the power turned off, recheck motor lead resistance to ground. A grounded lead can cause underload trip.
64
-!).4%.!.#%
%LECTRONIC 0RODUCTS
3UBTROL 0LUS /BSOLETE
3EE 3UB-ONITOR
Subtrol-Plus - Troubleshooting After Installation (Continued)
SYMPTOM
Tripped Light On
Control Circuit
Fuse Blows
Contactor Will
Not Close
POSSIBLE CAUSE OR SOLUTION
Whenever the pump is off as a result of Subtrol-Plus protective function, the red tripped light is on.
A steady light indicates the Subtrol-Plus will automatically allow the pump to restart as described,
and a flashing light indicates repeated trips, requiring manual reset before the pump can be restarted.
Any other red light operation indicates a faulty receiver. One-half voltage on 460 V will cause tripped
light on.
With power turned off, check for a shorted contactor coil or a grounded control circuit lead. The
coil resistance should be at least 10 ohms and the circuit resistance to panel frame over 1 megohm.
A standard or delay-type 2 amp fuse should be used.
If proper voltage is at the control coil terminals when controls are operated to turn the pump on, but
the contactor does not close, turn off power and replace the coil. If there is no voltage at the coil,
trace the control circuit to determine if the fault is in the Subtrol-Plus receiver, fuse, wiring, or panel
operating switches. This tracing can be done by first connecting a voltmeter at the coil terminals,
and then moving the meter connections step by step along each circuit to the power source, to
determine at which component the voltage is lost.
With the Subtrol-Plus receiver powered up, with all leads disconnected from the control terminals
and with an ohmmeter set at RX10, measure the resistance between the control terminals. It should
measure 100 to 400 ohms. Depress and hold in the reset button. The resistance between the
control terminals should measure close to infinity.
65
Contactor Hums or Chatters
Check that coil voltage is within 10% of rated voltage. If voltage is correct and matches line voltage,
turn off power and remove the contactor magnetic assembly and check for wear, corrosion, and dirt.
If voltage is erratic or lower than line voltage, trace the control circuit for faults similar to the previous
item, but looking for a major drop in voltage rather than its complete loss.
Contactor Opens When Start
Switch is Released
Check that the small interlocks switch on the side of the contactor closes when the contactor
closes. If the switch or circuit is open, the contactor will not stay closed when the selector switch
is in HAND position.
Contactor Closes But
Motor Doesn’t Run
Turn off power. Check the contactor contacts for dirt, corrosion, and proper closing when the
contactor is closed by hand.
Signal Circuit Terminals
Do Not Energize
With the Subtrol-Plus receiver powered up and all leads disconnected from the signal
terminals, with an 0hmmeter set at RX10, measure the resistance between the signal
terminals. Resistance should measure close to infinite. Depress and hold in the reset button.
The resistance between the signal terminals should measure 100 to 400 ohms.
!)- -!.5!,
!BBREVIATIONS
A
Amp or amperage
MCM
Thousand Circular Mils
AWG
American Wire Gauge
mm
Millimeter
BJT
Bipolar Junction Transistor
MOV
Metal Oxide Varister
°C
Degree Celsius
NEC
National Electrical Code
CB
Control Box
NEMA
CRC
Capacitor Run Control
National Electrical Manufacturer
Association
DI
Deionized
Nm
Newton Meter
Dv/dt
Rise Time of the Voltage
NPSH
Net Positive Suction Head
EFF
Efficiency
OD
Outside Diameter
°F
Degree Fahrenheit
OL
Overload
FDA
Federal Drug Administration
PF
Power Factor
FL
Full Load
psi
Pounds per Square Inch
ft
Foot
PWM
Pulse Width Modulation
ft-lb
Foot Pound
QD
Quick Disconnect
ft/s
Feet per Second
R
Resistance
GFCI
Ground Fault Circuit Interrupter
RMA
Return Material Authorization
gpm
Gallon per Minute
RMS
Root Mean Squared
HERO
High Efficiency Reverse Osmosis
rpm
Revolutions per Minute
hp
Horsepower
SF
Service Factor
Hz
Hertz
SFhp
Service Factor Horsepower
ID
Inside Diameter
S/N
Serial Number
IGBT
Insulated Gate Bipolar Transistor
TDH
Total Dynamic Head
in
Inch
UNF
Fine Thread
kVA
Kilovolt Amp
V
Voltage
kVAR
Kilovolt Amp Rating
VAC
Voltage Alternating Current
kW
Kilowatt (1000 watts)
VDC
Voltage Direct Current
L1, L2, L3 Line One, Line Two, Line Three
VFD
Variable Frequency Drive
lb-ft
Pound Feet
W
Watts
L/min
Liter per Minute
XFMR
Transformer
mA
Milliamp
Y-D
Wye-Delta
max
Maximum
1
ohms
66
!)- -!.5!,
.OTES
!)- -!.5!,
.OTES
!)- -!.5!,
.OTES
!)- -!.5!,
.OTES
TOLL FREE HELP FROM A FRIEND
nääÎ{nÓ{ÓäÊUÊÓÈänÓÇx£äÓÊv>Ý®
Phone Franklin’s toll free SERVICE HOTLINE for answers to your pump and
motor installation questions. When you call, a Franklin expert will offer assistance
in troubleshooting and provide immediate answers to your system application
questions. Technical support is also available online. Visit our website at:
ÜÜÜ°vÀ>iiVÌÀV°V
The Company You Trust Deep Down
M1311 07.11
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes Apple Keywords : Author : Brown, Tyler Create Date : 2011:08:05 17:23:56Z Modify Date : 2014:06:09 11:34:21-04:00 Subject : XMP Toolkit : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03 Creator Tool : Preview Metadata Date : 2014:06:09 11:34:21-04:00 Format : application/pdf Description : Creator : Brown, Tyler Title : M1311_60_Hz_AIM_Catalog Keywords : Producer : Mac OS X 10.6.6 Quartz PDFContext Document ID : uuid:61bbdb03-36bf-3e4e-abb5-b14e49466fd6 Instance ID : uuid:769ae075-ec28-4486-b371-0f67305fbc5e Page Count : 80EXIF Metadata provided by EXIF.tools