218 2 Zoeller Pro Pak 98 Instructions User Manual

217 2 Zoeller Pro Pak 98 Instructions 217_2_Zoeller Pro Pak 98 Instructions 217_2_Zoeller Pro Pak 98 Instructions pdf pumpproducts

User Manual: Pump 218 2 Zoeller Pro Pak 98 Instructions

Open the PDF directly: View PDF .
Page Count: 8

NOTICE TO INSTALLER: Instructions must remain with installation. SECTION: 6.10.072

FM2562

0113

Supersedes

1111

NOTICE: VENT HOLE FOR

CHECK VALVE

SEE #3 IN CAUTION SECTION

BELOW AND #4 ON PAGE 3

DATE INSTALLED:

MODEL NUMBER:

PREASSEMBLED SUMP PUMP SYSTEM WITH BATTERY BACKUP

MODEL 507 - 12V DC BATTERY BACKUP SYSTEM

WITH 120V AC POWERED SUMP PUMP

MODEL WM49, M53 or M98

INSTALLATION INSTRUCTIONS

SEE BELOW FOR

LIST OF WARNINGS

1. Make certain that the receptacle is within the reach of the pump’s power supply cord.

Do not use primary pump circuit. DO NOT USE AN EXTENSION CORD. Extension

cords that are too long or too light do not deliver sufcient voltage to the pump motor.

But, more important, they could present a safety hazard if the insulation were to

become damaged or the connection end were to fall into the sump.

2. Make sure the pump electrical supply circuit is equipped with fuses or circuit breakers

of proper capacity. A separate branch circuit is recommended, sized according to

the “National Electrical Code” for the current shown on the pump nameplate.

3. Testing for ground. As a safety measure, each electrical outlet should be checked for

ground using an Underwriters Laboratory Listed circuit analyzer which will indicate

if the power, neutral and ground wires are correctly connected to your outlet. If they

are not, call a qualied licensed electrician.

4. For Added Safety. Pumping and other equipment with a 3-prong grounded plug must

be connected to a 3-prong grounded receptacle. For added safety the receptacle

may be protected with a ground-fault circuit interrupter. When a pump needs to be

connected in a watertight junction box, the plug can be removed and spliced to the

supply cable with proper grounding. For added safety this circuit may be protected

by a ground-fault circuit interrupter. The complete installation must comply with the

National Electrical Code and all applicable local codes and ordinances.

5. FOR YOUR PROTECTION, ALWAYS DISCONNECT PUMP FROM ITS POWER

SOURCE BEFORE HANDLING. Single phase pumps are supplied with a 3-prong

grounded plug to help protect you against the possibility of electrical shock. DO

NOT UNDER ANY CIRCUMSTANCES REMOVE THE GROUND PIN. The 3-prong

plug must be inserted into a mating 3-prong grounded receptacle. If the installation

does not have such a receptacle, it must be changed to the proper type, wired and

grounded in accordance with the National Electrical Code and all applicable local

codes and ordinances.

6. The tank is to be vented in accordance with local plumbing code. Pumps must be

installed in accordance with the National Electrical Code and all applicable local codes

and ordinances. Pumps are not to be installed in locations classied as hazardous

in accordance with National Electrical Code, ANSI/NFPA 70.

7. “Risk of electrical shock” Do not remove power supply cord and strain relief

or connect conduit directly to the pump.

8. Installation and servicing of electrical circuits and hardware should be performed by

a qualied licensed electrician.

9. Pump installation and servicing should be performed by a qualied person.

10. Risk of electric shock - These pumps have not been investigated for use in swimming

pool and marine areas.

11. According to the state of California (Prop 65), this product contains chemicals known

to the state of California to cause cancer and birth defects or other reproductive harm.

12. It is the owner’s responsibility to check the battery and battery connection at least

once a month. Batteries contain acid and caution must be taken when handling.

1. Check to be sure your power source is capable of handling the voltage requirements

of the motor, as indicated on the pump name plate.

2. The installation of automatic pumps with variable level oat switches or nonau-

tomatic pumps using auxiliary variable level oat switches is the responsibility of

the installing party and care should be taken that the tethered oat switch will

not hang up on the pump apparatus or pit peculiarities and is secured so that the

pump will shut off. It is recommended to use rigid piping and ttings and the pit

be 18" or larger in diameter.

3. Information - vent hole purpose. It is necessary that all submersible sump, efuent,

and sewage pumps capable of handling various sizes of solid waste be of the

bottom intake design to reduce clogging and seal failures. If a check valve is

incorporated in the installation, a vent hole (approx. 3/16") must be drilled in the

discharge pipe below the check valve and pit cover to purge the unit of trapped

air. Trapped air is caused by agitation and/or a dry basin. Vent hole should be

checked periodically for clogging. The 50 Series pumps have a vent located in

the pump housing opposite the oat, adjacent to a housing lug, but an additional

vent hole is recommended. If you choose not to drill a vent hole, be sure the

pump case and impeller is covered with liquid before connecting the pipe to the

check valve and no inlet carries air to the pump intake. NOTE: THE HOLE

MUST ALSO BE BELOW THE BASIN COVER AND CLEANED PERIODICALLY.

Water stream will be visible from this hole during pump run periods.

4. Pump should be checked frequently for debris and/or build up which may interfere

with the oat “on” or “off” position. Repair and service should be performed by

Zoeller Pump Company Authorized Service Station only.

5. Dewatering and efuent sump pumps are not designed for use in pits handling

raw sewage.

6. Maximum operating temperature must not exceed 104ºF (40ºC).

7. Do not operate a pump in an application where the Total Dynamic Head is less

than the minimum Total Dynamic Head listed on the Pump Performance Curves.

8. For indoor use only.

9. DC emergency pumps are designed for handling clear water. Do not use in septic

tanks to pump efuent or sewage pits to pump sewage.

10. Repair and service of your DC backup system should be performed by an

authorized service station.

11. The installation of DC automatic backup pumps requires the use of a variable level

oat switch for operation. It is the responsibility of the installing party, to ensure

that the oat switch will not hang up on the pump apparatus or pit peculiarities and

is secured so the pump will turn “on” and “off”. It is recommended that the pit be

18" in diameter or larger to accommodate both a primary and a DC backup pump.

NOTE: Pumps with the “UL” mark and pumps with the “US” mark are tested to UL Standard UL778.

CSA Certied pumps are certied to CSA Standard C22.2 No. 108.

REFER TO WARRANTY ON PAGE 2.

SEE BELOW FOR

LIST OF CAUTIONS

Product information presented

here reects conditions at time

of publication. Consult factory

regarding discrepancies or

inconsistencies.

MAIL TO: P.O. BOX 16347 • Louisville, KY 40256-0347

SHIP TO: 3649 Cane Run Road • Louisville, KY 40211-1961

(502) 778-2731 • 1 (800) 928-PUMP • FAX (502) 774-3624

visit our web site:

www.zoeller.com

Your Peace of Mind is Our Top Priority

LIMITED WARRANTY

Manufacturer warrants, to the purchaser and subsequent owner during

the warranty period, every new product to be free from defects in material

and workmanship under normal use and service, when properly used and

maintained, for a period of three years from date of purchase by the end

user. Parts that fail within the warranty period, that inspections determine

to be defective in material or workmanship, will be repaired, replaced or

remanufactured at Manufacturer's option, provided however, that by so doing we

will not be obligated to replace an entire assembly, the entire mechanism or the

complete unit. No allowance will be made for shipping charges, damages, labor

or other charges that may occur due to product failure, repair or replacement.

This warranty does not apply to and there shall be no warranty for any material

or product that has been disassembled without prior approval of Manufacturer,

subjected to misuse, misapplication, neglect, alteration, accident or act of

God; that has not been installed, operated or maintained in accordance with

Manufacturer's installation instructions; that has been exposed to outside

substances including but not limited to the following: sand, gravel, cement,

mud, tar, hydrocarbons, hydrocarbon derivatives (oil, gasoline, solvents,

etc.), or other abrasive or corrosive substances, wash towels or feminine

sanitary products, etc. in all pumping applications. The warranty set out in

the paragraph above is in lieu of all other warranties expressed or implied; and

we do not authorize any representative or other person to assume for us any

other liability in connection with our products.

Contact Manufacturer at, 3649 Cane Run Road, Louisville, Kentucky 40211,

Attention: Product Support Department to obtain any needed repair or

replacement of part(s) or additional information pertaining to our warranty.

MANUFACTURER EXPRESSLY DISCLAIMS LIABILITY FOR SPECIAL,

CONSEQUENTIAL OR INCIDENTAL DAMAGES OR BREACH OF

EXPRESSED OR IMPLIED WARRANTY; AND ANY IMPLIED WARRANTY

OF FITNESS FOR A PARTICULAR PURPOSE AND OF MERCHANTABILITY

SHALL BE LIMITED TO THE DURATION OF THE EXPRESSED WARRANTY.

Some states do not allow limitations on the duration of an implied warranty,

so the above limitation may not apply to you. Some states do not allow the

exclusion or limitation of incidental or consequential damages, so the above

limitation or exclusion may not apply to you.

This warranty gives you specic legal rights and you may also have other rights

which vary from state to state.

In those instances where damages are incurred as a result of an alleged pump failure,

the Homeowner must retain possession of the pump for investigation purposes.

The DC emergency pump is designed as a backup to your primary sump pump during unexpected power outages or primary pump failure. The DC

pump, electronic controls and all the parts required for installation are included except the battery which is supplied by the user. The system is designed

for installation in sumps with minimum of 18" diameter and 24" deep. For 18" x 22" applications, consult factory.

DESCRIPTION

The DC emergency pump system requires a good quality, 12 volt battery to obtain maximum pumping time during a power outage. A deep-cycle, 12

volt, 105 amp-hour marine battery or larger is recommended and will provide approximately 7½ hours of continuous pumping time in a sump pump

installation with 8' of head pressure. In most installations the pump runs intermittently and the battery life is extended accordingly. Batteries with top

terminals are recommended for ease of installation. These batteries contain acid and proper precaution must be taken when handling. Maximum bat-

tery size 12½" Length x 7" Width x 9½" Height.

BATTERY SELECTION

There are millions of batteries manufactured each year, so it is impossible to guarantee consistent quality. A defective battery will never become fully

charged and may damage the charging circuits of the Control. It is for this reason that Zoeller offers its own line of batteries. We offer both a Water/

Acid Deep-Cycle Battery which can run the pump continuously for over 7½ hours, and a Maintenance-Free AGM Battery, which will power the pump for

over 3½ hours. These times are based on continuous pumping at 10' of static head. Actual times will vary depending on static head, volume of water

entering the pit, and the condition of the battery.

Follow these recommendations:

• Use a B.C.I. size 27 deep-cycle battery, 175 minute reserve capacity, or larger

• Do NOT use a “maintenance-free” battery unless it is a Gel-filled or AGM battery

• Replace your battery every 3 years

• Do not let corrosion build up on the battery terminals

• Do not place your battery on a concrete floor where it will discharge faster

• To check specific gravity, follow the instructions on a hydrometer (not applicable for Gel or AGM batteries)

PROTECT YOUR WARRANTY:

• Water level in batteries must be checked once a month (not applicable for Gel or AGM batteries)

THE AQUANOT® BATTERY

IMPORTANT NOTICE: Some insurance policies, both commercial and residential, extend coverage for damages incurred by product failure. You will need to

have possession of the product to support your claim in most cases. Zoeller Pump Co. will exchange the unit or refund the original purchase price once the claim

is settled with the insurer in the case where you need to retain possession of the product to support a damage claim you submit to your insurance company.

1. Electrical wiring and protection must be in accordance with National

Electrical Code and any other applicable state and local electrical

requirements.

2. All installations require a basin cover to prevent debris from falling into

the basin and to prevent accidental injury.

3. Securely tape or clamp power cord to discharge pipe, clear of the oat

mechanism(s).

4. Use full-size discharge pipe.

5. Basin must be in accordance with applicable codes and specications.

6. Pump must be level and oat mechanism(s) clear of sides of basin

before starting pump. Float switch may be repositioned as needed.

7. Basin must be clean and free of debris after installation.

8. Gate Valve or Ball Valve to be supplied by installer and installed

according to any and all codes.

9. Gas tight seals required to contain gases and odors.

10. Vent gases and odors to the atmosphere through vent pipe.

11. Install Zoeller Pump Stand (Model 10-2421) under pump to

provide a settling basin.

RECOMMENDED INSTALLATION FOR ALL APPLICATIONS

EASY DO'S & DON'TS FOR INSTALLING A SUMP PUMP

1. DO read thoroughly all installation material provided with the system.

2. DO inspect system for any visible damage caused by shipping. Contact

dealer if system appears to be damaged.

3. DO clean all debris from the sump. Be sure that the pump will have a hard,

at surface beneath it. DO NOT install on sand, gravel or dirt.

4. DO be sure that the sump is large enough to allow proper clearance for the

level control switch(es) to operate properly.

5. DO Always Disconnect Pump From Power Source Before Handling.

DO always connect to a separately protected and properly grounded circuit.

DO NOT ever cut, splice, or damage power cord (Only splice in a watertight

junction box).

DO NOT carry or lift pump by its power cord.

DO NOT use an extension cord with a sump pump.

6. DO install a union in the discharge line.

DO NOT use a discharge pipe smaller than the pump discharge.

7. DO NOT use a sump pump as a trench or excavation pump, or for pumping

sewage, gasoline, or other hazardous liquids.

8. DO test system immediately after installation to be sure that the system is

working properly.

9. DO cover sump with an adequate sump cover.

10. DO review all applicable local and national codes and verify that the installation

conforms to each of them.

11. DO consult manufacturer for clarications or questions.

12. DO inspect and test system for proper operations at least every three months.

The DC controller is equipped with a 10 amp charger for maintaining the battery in a ready state and recharging the battery after use when AC power

is restored. Time for recharge depends upon the amount of power consumed by the pumping cycle during the AC power interruption. The pump may

go back to the ready run position in a very short period of time. A completely drained battery may require up to 24 hours for full recharge. If after 24

hours of charging the battery has not reached 6 volts, the alarm will sound and not reset until the battery is brought up to a voltage of 6.5-7.0 volts.

PERFORMANCE

Discharge Feet of Head 510 15 17.5

Flow Gal. per min. 23 15 5Shut-off Head

The DC pump performance with fully charged 12V battery

SK2750

For Installation, Maintenance, Troubleshooting and Service Checklist, please refer to

the corresponding Pump Installation Manual and Replacement Parts List.

SK2752

TYPICAL INSTALLATION EXPLODED VIEW OF PUMP SYSTEM

FIGURE 1

DC PUMP PLUMBED IN LINE WITH SUBMERSIBLE PUMP

PRIMARY PUMP OUTLET

BATTERY BOX

IMPORTANT: OFF LEVEL OF

FLOAT ASSEMBLY MUST BE

1"MIN. ABOVE CENTER OF TEE.

(SEE INSTALLATION NOTE 3.)

VERIFY WEEP HOLE IS

VISIBLE. (SEE PUMP

INSTALLATION INSTRUCTIONS)

CHECK VALVE

WEEP HOLE PROVIDED

PUMP DISCHARGE

CHARGER OUTLET

(MUST BE INSTALLED

ON TWO SEPARATE

CIRCUITS.)

1"MIN.

DETAIL "A"

(SCALE: 4X)

SEE DETAIL "A"

FIGURE 2

INSTALLATION

5. Connect the leads from the control charger to the battery terminals. Red

pos. (+) lead to positive terminal and black neg. (-) lead to negative battery

terminal. Upon proper connection, test alarm will sound. Press alarm

reset to silence. This indicates proper charger to battery connection.

Correct battery hook up is essential for operation of the

system. Use nuts supplied with battery and eyelet connectors on battery

wire leads. The positive terminal is the larger stud, 3/8" diameter. The

smaller stud, 5/16" diameter is the negative terminal. Apply grease to the

terminals to help prevent corrosion.

6. Connect the black lead from the pump to the negative (-) battery terminal.

Connect the white or red lead from the pump to the white lead from the

switch. This connection is made at the fuse installed on the switch wire

(see gure 3). Connect the black lead from the switch to the positive (+)

battery terminal.

7. Connect the blue sensor wire to the sensor connector (gure 3).

8. Close battery box and secure cover. Carpeted or wood barrier between

the battery case and the oor is recommended.

9. Plug the control power cord into the 115V wall outlet. The primary sump

pump and the control box should be on separate circuits.

10. Reconnect power to primary sump pump.

1. The preferred method of installation for backup pumps is shown in gure 1.

The installation kit includes one check valve for installing with the backup

pump discharging into the primary pump outlet pipe. An additional check

valve is incorporated in the discharge of the backup pump.

2. Select location for battery and control charger. Control charger must be

within 6' of a 115V wall outlet and within 6' of pump and basin. Connect to

a separate circuit, different than the primary pump.

3. Make certain the oat switch clamp is tight on the pipe to avoid slippage.

Use electrical tape below the clamp to help prevent the clamp from moving.

Ensure that the “off” level of the oat is 1" min. above the discharge tee of

the DC backup pump (see gure 1). Position pumps in the sump and move

oat up and down, making sure of free movement without interference from

any obstructions inside the sump or lid. Very shallow sumps may require

some adjustment to avoid overlling or backing up of water into the sump

inlet. The oat switch can be moved on the discharge pipe or the rubber

stops can be adjusted as necessary. Cut extra oat rod length below lower

oat stop to prevent debris from interfering with oat operation (see gure 2).

4. Install DC control charger (see gure 3) by using the wall bracket and

anchors provided. If more convenient, the control charger may be set on

a nearby shelf or ledge. The control charger should be located 3 or 4 ft.

above the sump. To reduce noise from vibration, it is recommended that

the charger be anchored with the wall bracket provided.

INITIAL START-UP AND OPERATION

1. Test the installation for leaks by running water into the sump allowing for

normal operation of the primary pump.

2. Check the control charger. The “red” power on light will be lit when the unit

is plugged into the 115V wall outlet. The “yellow/green” light will indicate

the condition of the battery.

3. Disconnect primary pump before touching any component in the sump pit.

4. Lift oat switch. The DC backup pump will run and the alarm will sound.

Lower oat switch immediately after pump has started running. Pump is

running dry during initial check out for several seconds.

Continuous dry running may cause overheating and damage the pump

seals. Upon release of the oat switch, the pump will shut off. Press the

reset button to turn the alarm off.

5. Complete the nal testing of your installation by disconnecting the power

to the primary pump and the control charger by removing the plugs from

the 115V wall outlets. Run water into the sump until the DC backup pump

is activated by the oat switch. Check all connections for leaks.

6. Push alarm reset switch when pump is running. This will silence the alarm.

The pump will continue to run.

7. Reconnect the control charger and your primary pump to the AC wall outlets.

The primary pump should come on and lower the water level in the sump

back to the normal operating level and shut off. Both primary and backup

systems are now ready for use.

8. The battery charged and charging LED’s will alternate during normal

charging operation.

MAINTENANCE

1. Inspect and test the system for proper operations at least every 3 months.

(a) Red power on indicator light should be “on” indicating AC

power is on.

(b) Unplug primary pump and the control charger from power supply.

pump to run a few minutes.

(d) The alarm will sound approximately 5 seconds after the pump

starts to run.

(e) Push alarm reset switch. The alarm will go “off”.

(f) Pump will shut off after water level is lowered and the float drops

to the off position.

2. Plug the control charger and the primary pump into the wall outlet.

(a) The primary pump will come on and lower the water to the

normal operating level and shut off.

(b) The “yellow” charging light should be on. The charger is replacing

the energy consumed during the test. The “green” light will come

on after the charger has replaced the energy consumed during

the test.

3. Battery should be agitated gently every 3 months.

Battery acid is dangerous. Take proper safety precautions. Do not

splash the acid. Add distilled water to battery when necessary per

battery manufacturer's instructions.

MODEL 507-A

ITEM DESCRIPTION QTY

9/10

thru

Current

1 Pump, 12V DC with terminals 1017198

2 Battery box 110-0764

3 DC control charger with terminals 1011323

4 “Off”/”On” oat switch 1017197

5 Check valve 1019768

6 Hose coupling and clamps 1019857

Pump, M53/115V (507-0008)

53-0001

Pump, M98/115V (507-0011) 98-0001

Pump, WM49/115V (507-0009) 49-0005

8 1-1/2" PVC pipe tee 1005645

9 1-1/2" X 2-1/8" long pipe 1150197

10 1-1/2" X 8-3/4" long pipe 1010619

11 Hardware pack (507) 1017196

CHECKLIST

EXPLODED VIEW - DC PUMP

All installations must comply with all applicable electrical and plumbing codes, including, but not limited to, National Electrical

Code, local, regional, and/or state plumbing codes, etc. Not intended for use in hazardous locations.

SK2501

BATTERY BOX

12 VOLT

MARINE BATTERY

SUPPLIED BY USER

FIG. 5

DC BACK-UP PUMP

CLAMP

FLOAT SWITCH

BLACK WITH RED

TRACER TO POSITIVE

BLACK LEAD

TO POSITIVE

WHITE LEAD

TO DC PUMP

BLACK LEAD

TO NEGATIVE

TO FLOAT

RED LEAD

15 AMP FUSE

DC CONTROL BOX

BLACK LEAD

TO NEGATIVE

TO FLOAT SWITCH

BLUE LEAD

SPLICER

WHITE OR

FIGURE 3

ELECTRICAL PRECAUTIONS- Before servicing a pump, always shut off the main power breaker and then unplug the pump - making

sure you are wearing insulated protective sole shoes and not standing in water. Under ooded conditions, contact your local electric company or a

qualied licensed electrician for disconnecting electrical service prior to pump removal.

Submersible pumps contain oils which becomes pressurized and hot under operating conditions - allow 2½ hours after disconnecting before

attempting service.

If the above checklist does not uncover the problem, consult the factory - Do not attempt to service or otherwise disassemble pump. Service must be

performed by Zoeller Authorized Service Stations. Go to www.zoellerpumps.com/service stations to nd the Authorized Service Station in your area.

SERVICE CHECKLIST

TROUBLESHOOTING INFORMATION

1. Charging and charged LED’s alternate frequently.

(a) This is normal.

2. DC Pump won’t run.

(a) Check 15 amp fuse in line from pump to switch (see g. 4). If fuse

is blown, replace with 15 amp Littelfuse type 3AG, series 311.

(b) Check for proper connections.

(d) Check for low battery. Service battery if required.

3. Pump runs but pumps very little or no water.

(a) Check for low battery. Battery will recharge if Red power “on”

light indicates power has been restored and the oat switch is

in the off position.

(b) If immediate usage is required, remove and replace dead

battery with a full recharged battery.

low battery without sufcient power to remove water. Pump will

not stop running until battery is completely discharged.

(d) Weak batteries can be recharged but may

not store sufcient energy for full service. A weak recharged

battery can only be detected by reduced pumping time or by

checking each cell with a hydrometer. If your emergency pump

system is used frequently the battery should be checked by a

qualied battery dealer.

4. Pump cycles too frequently.

(a) Check positions of rubber stops on oat rod.

(b) Adjust upper rubber oat stop as required. Recommended for

standard installation.

5. Float switch in “on” position. Pump won’t run.

(a) Remove pump. Check for obstruction in pump preventing

impeller from rotating.

6. Pump runs, but pumps water intermittently.

(a) Pump is air locking. Check ow of water incoming to sump. If

water is entering the sump at a high velocity creating a turbulent

condition, a mixture of air and water may cause a complete

or partial air lock and reduce or stop the ow of water in the

discharge pipe.

(b) Bafe the incoming stream of water to reduce turbulence.

Diverting water stream against wall of basin usually corrects an

air lock problem.

7. Water level stays high. DC Pump continues to run.

(a) Battery is low.

(b) If power has been restored and water in sump remains high

check primary pump. Service if required.

8. Alarm sounds during battery recharge cycle.

(a) Push alarm reset (max. 3 times). If condition persists, replace

battery.

(b) To silence alarm if alarm will not reset, unplug the charger from

115V wall outlet, then disconnect the black lead from charger on

negative (-) battery post. Check battery. Replace if necessary.

Reconnect and refer to Installation (step 7).

CONDITION COMMON CAUSES

A. Pump will not start or run.

Check fuse, low voltage, overload open, open or incorrect wiring, open switch, impeller or seal bound mechanically, motor

or wiring shorted. Float assembly held down. Switch, damaged or out of adjustment.

B. Motor overheats and trips

overload or blows fuse.

Incorrect voltage, negative head (discharge open lower than normal) impeller or seal bound mechanically, motor shorted.

C. Pump starts and stops too often.

Float switch tether length too short, check valve stuck open, or none installed in long distance line, overload open, bidding,

sump pit too small.

D. Pump will not shut off.

Debris under oat assembly, oat bound by basin sides or other, switch, damaged or out of adjustment.

E. Pump operates but delivers little

or no water.

Check inlet, strainer housing, discharge pipe, and vent holes for obstructions. Discharge head exceeds pump capacity.

Low or incorrect voltage. Incoming water containing air or causing air to enter pumping chamber. Incorrect motor rotation.

(3 phase pumps only)

F. Drop in head and/or capacity

after a period of use.

Increased pipe friction, clogged line or check valve. Abrasive material and adverse chemicals could possibly deteriorate

impeller and pump housing. Check line. Remove base and inspect.

G. If tank or ttings leak.

Carefully tighten pipe joints (use pipe dope) and screws. Check gasket location, tighten lid evenly. Do not over tighten

ttings or screws.

CARBON MONOXIDE DETECTORS

Whether you have a “Basement Sentry®” Backup Pump System, or a competitive brand, all use batteries that give off gaseous by-products when charging.

Some of these by-products can produce a rotten egg odor. Also, some of these by-products can cause a CO detector to falsely activate. In order to help

prevent false activation, Zoeller Company recommends moving the battery as far apart from the CO detector as possible or, if necessary, vent the battery to the

exterior. Zoeller Company provides the previous statements only as guidelines to help prevent false activation of the CO detector. In no way are they meant

to supersede the instructions that accompany the detector nor do they supersede advice from the CO detector manufacturer.

If the audible alarm associated with your CO detector is activated, we recommend the following actions:

1) Take immediate action for personal safety as recommended in the CO detector literature.

2) Contact the appropriate agency to determine if the CO is being produced by your furnace, water heater, or any other device which uses natural gas.

3) If you are certain that no CO is being produced, then a charging battery may be producing gaseous by-products which are causing the CO detector

to activate. Contact the manufacturer and ask for recommendations as to what can be done to prevent the alarm activation.

FLOAT SWITCH CONTROL CHARGER

FIG. 4

LOCKING PIN MUST BE

INSTALLED UNDER FLOAT

ROD IN THIS LOCATION.

NON-GROUNDED

POWER CORD

ALARM RESET

POWER ON

BLACK LEAD TO

NEG. BATTERY TERMINAL

BLUE LEAD TO

FLOAT SWITCH

TO POS. BATTERY TERMINAL

BLACK WITH RED TRACER

"RED"

"CHARGING-YELLOW"

"CHARGED-GREEN"

INDICATOR

FIGURE 4 SK2503 FIGURE 5 SK1424

MAIL TO: P.O. BOX 16347 • Louisville, KY 40256-0347

SHIP TO: 3649 Cane Run Road • Louisville, KY 40211-1961

(502) 778-2731 • 1 (800) 928-PUMP • FAX (502) 774-3624

Your Peace of Mind is Our Top Priority ®

®visit our web site:

www.zoeller.com

218 2 Zoeller Pro Pak 98 Instructions User Manual

217 2 Zoeller Pro Pak 98 Instructions 217_2_Zoeller Pro Pak 98 Instructions 217_2_Zoeller Pro Pak 98 Instructions pdf pumpproducts

Navigation menu

Versions of this User Manual:

Views

Navigation