539743 1 Sta Rite HMS Series Jet Pump Brochure
: Pump 539743 1 Sta-Rite Hms Series Jet Pump Brochure 539743_1_Sta-Rite HMS Series Jet Pump Brochure pdf
Open the PDF directly: View PDF 
.
Page Count: 4
STA-RITE® HMS Series
Cast iron horizontal multi-stage jet pumps
HMS Series Multi-Stage Jet Pumps are
the highest performing pumps
available in its category. The HMS
Series Convertible Jets utilize the
built-in regulator, offering easier
priming and better range of
performance from a complete line of
Shallow Well, 4" Double Pipe, 2" and 3"
Single Pipe Jet Packages. Pump may
also be operated as a self-priming
centrifugal (to 25 ft.) to provide a wide
range of high pressure applications.
APPLICATIONS
Water systems and sprinkling…
for homes, farms and cottages.
SPECIFICATIONS
Body:
One-piece rugged cast iron
Pump and Motor Shaft:
416 stainless steel
Impeller:
Polycarbonate
Diffuser:
Corrosion-resistant cast iron
Pressure Switch Pre-Set:
30–50 PSI
Suction Ports:
Drive-over-Suction
FEATURES
Automatic Pressure Regulator:
Faster-
acting and quieter, design eliminates
“hunting” for correct drive pressure. New
improved stem and guide are precisely
molded to assure efficient, trouble-free
performance on all deep wells. See ordering
information (deep well only).
Quality Construction:
Close-grained cast
iron pump body is rugged, one-piece unit,
specially treated to resist corrosion. Drain
port provided for easy winterizing.
Precision-Machined Diffusers:
Assure faster priming.
Mechanical Shaft Seal:
Precision-lapped
and highly polished carbon-ceramic,
stainless steel construction. Internal design
guarantees continuous water lubrication for
maximum protection.
Polycarbonate Impellers:
Precision-
molded for perfect balance, and ultra-
smooth for highest performance
and efficiency.
Motor Windings:
Superior insulation
materials protect against excessive
moisture and contaminants to ensure
prolonged motor life.
Dustproof Cover:
All electrical
components are protected from dirt,
dust and insects by a dust proof canopy.
Ventilating air cannot contam inate vital
switching components. This eliminates the
most common cause of motor failure.
Balanced Rotor:
Diecast under high
pressures for uniform performance and
greater efficiency...dynamically balanced.
Heavy-Duty Ball Bearings:
Shielded,
permanently lubricated bearings are
extensively tested to ensure extended
life and smooth, quiet operation.
Pump and Motor Shaft:
Stainless steel for
maximum corrosion resistance;. one-piece
threaded shaft for positive impeller drive
and alignment.
Order pump and pressure regulator, if required, from ordering information tables above.
A Jet Package and the Automatic Pressure Regulator, described above, are required on all deep well installations.
UL778/CSA108
ORDERING INFORMATION
CATALOG
NUMBER HP DESCRIPTION PIPE TAPPING SIZES STAGES MOTOR
VOLTAGE
APPROX.
WT. LBS.
SUCT. DRIVE DISCH.
HMSD 3/4 Deep Well Jet 1-1/4" 1" 1" 2 115/230 50
HMSE 1 Deep Well Jet 1-1/4" 1" 1" 2 115/230 80
HMSF 1-1/2 Deep Well Jet 1-1/4" 1" 1" 2 115/230 85
AUTOMATIC PRESSURE REGULATOR DEEP WELL
CATALOG
NUMBER DESCRIPTION APPLICATION APPROX.
WT. LBS.
PKG 107 Regulator, tubing, pipe plug and
compression fitting
Required for ALL deep well
installations 4
1S4511WS
STA-RITE® HMS Series
Cast iron horizontal multi-stage jet pumps
* Order Jet Package separately.
Tested and rated in accordance with Water Systems Council Standards.
NOTE: Pumps installed with a Pro-Source® tank require a 100 PSI relief
valve. Pumps installed with a conventional tank require a 75 PSI
relief valve. Relief valve must be capable of relieving entire flow of
pump at relief pressure.
180
160
140
120
100
80
60
40
20
0102030405060
10' 10'
10'
15'
15'
15'
20'
20' 20'
25'
25'
25'
TOTAL HEAD IN FEET
CAPACITY GALLONS PER MINUTE
70
CAPACITY LITERS PER MINUTE
TOTAL HEAD IN METERS
100 250200500 150
50
40
30
20
10
0
HMSF
HMSE
HMSD
NOTE: Dotted lines indicate performance reduction at high suction lift.
PUMP PERFORMANCE
PUMP PERFORMANCE: SHALLOW WELL
CATALOG
NUMBER HP JET*
NUMBER
USES
VENTURI
USES
NOZZLE
DISCH.
PRESS. PSI
TOTAL SUCTION LIFT FT.
5' 10' 15' 20' 25'
HMSD 3/4 PKG 1 - 29SD N32P-66B J34P-41
20 9.6 8.2 7.0 5.8 3.9
30 9.1 7.9 6.5 5.6 3.9
40 8.8 7.7 6.3 5.6 3.9
50 8.5 7.6 6.2 5.6 3.9
60 7.7 7.3 6.2 5.6 3.9
70 5.5 5.1 4.7 4.2 3.6
80 3.5 3.1 2.8 2.3 1.9
Shut-off 102 96 96 96 90
HMSE 1 PKG 1 - 10SD N32P-67B J34P-44
20 13.0 11.2 9.8 7.8 5.8
30 12.5 11.0 9.5 7.6 5.7
40 12.2 10.9 9.4 7.6 5.7
50 12.1 10.8 9.2 7.6 5.7
60 12.0 10.8 9.2 7.6 5.7
70 10.2 9.6 8.6 7.4 5.7
80 7.4 6.8 6.2 5.5 4.8
Shut-off 108 108 108 102 102
HMSF 1-1/2 PKG 1 - 10SD N32P-67B J34P-44
20 15.9 13.3 12.2 9.6 7.0
30 15.6 13.2 12.2 9.5 7.0
40 15.3 13.1 12.1 9.4 6.9
50 14.9 13.0 11.9 9.3 6.8
60 14.4 12.9 11.7 9.2 6.7
70 13.7 12.7 11.5 9.0 6.6
80 12.6 12.1 10.8 8.7 6.4
90 9.5 8.5 7.8 7.2 5.7
100 5.9 5.0 4.4 3.8 3.2
Shut-off 120 120 114 114 108
2S4511WS
STA-RITE® HMS Series
Cast iron horizontal multi-stage jet pumps
Tested and rated in accordance with Water Systems Council Standards.
NOTE: Pumps installed with a Pro-Source® tank require a 100 PSI relief valve. Pumps installed with a conventional tank require
a 75 PSI relief valve. Relief valve must be capable of relieving entire flow of pump at relief pressure.
OUTLINE DIMENSIONS
A
1-15/16
1 NPT
DISCHARGE
1 NPT
DRIVE LINE
1-1/4 NPT
SUCTION
7-1/4
5-3/8
1/86 3-1/2
10-1/2 3-3/8
6-3/4
3-3/4
7-1/2
11-13/16
B
C
8-3/4
3-3/8 DIA.
(4) HOLES
1-1/4 NPT
6-3/4
(Order separately)
Dimensions (in inches) are for estimating purposes only.
PUMP PERFORMANCE (CaPaCity iN GalloNS PEr MiNutE)
CENTRIFUGAL APPLICATION
CATALOG
NUMBER HP
TOTAL
SUCTION
LIFT FT.
DISCHARGE PRESSURE PSI SHUTOFF
PRESSURE
PSI
20' 30' 40' 50' 60'
HMSD 3/4
5 37 30 24 15 – 60
10 35 29 21 13 – 60
15 33 27 19 9 – 60
20 32 26 17 6 – 60
25 31 24 15 – – 60
HMSE 1
5 47 40 33 24 10 65
10 46 38 31 21 7 65
15 44 36 28 18 – 65
20 42 35 26 15 – 65
25 41 33 24 12 – 65
HMSF 1-1/2
5 60 53 46 36 23 68
10 58 52 43 33 21 68
15 56 49 41 30 16 68
20 55 47 39 27 12 68
25 54 41 36 25 – 68
CAT. NO. A B C
HMSD 16-7/8 9-1/2 5-1/8
HMSE 17-3/4 9-1/2 5-1/8
HMSF 18-1/4 10 5-5/8
3S4511WS
STA-RITE® HMS Series
Cast iron horizontal multi-stage jet pumps
293 WRIGHT STREET, DELAVAN, WI 53115 WWW.STARITE.COM PH: 8887827483 ORDERS FAX: 8004269446
Because we are continuously improving our products and services, Pentair reserves the right to change specifications without prior notice.
Tested and rated in accordance with Water Systems Council Standards.
NOTE: Pumps installed with a Pro-Source® tank require a 100 PSI relief valve. Pumps installed with a conventional tank require
a 75 PSI relief valve. Relief valve must be capable of relieving entire flow of pump at relief pressure.
PUMP PERFORMANCE (CaPaCity iN GalloNS PEr MiNutE)
DEEP WELL 2" SINGLE PIPE: 40 PSI
CAT. NO. HP JET NO. USES
VENTURI
USES
NOZZLE
PUMPING DEPTH IN FEET
20' 30' 40' 50' 60' 70' 80' 90' 100' 110' 120' 130' 140' 150' 160'
HMSD 3/4
13AP J32P-26 J34P-44 12.0 10.8 9.6 8.1 6.9 5.5
22AP J32P-22 J34P-43 7.9 6.7 5.5 4.7 3.9 3.0
8AP J32P-18 J34P-42 4.0 3.6 3.1 2.7 2.2
HMSE 1
5AP J32P-29 J34P-41 16.3 15.6 14.1 12.0 9.9 8.2 6.0
4AP J32P-24 J34P-41 8.9 7.9 7.0 5.8 4.7 3.6 2.5
19AP J32P-20 J34P-43 4.0 3.2 2.3 1.8 1.3
HMSF 1-1/2
15AP J32P-33 J34P-41 20.0 18.5 17.0 13.6 10.4 7.6 5.0
9CP J32P-26 J34P-41 10.6 9.2 8.0 6.0 4.5 3.7 3.0 2.2
23AP J32P-20 J34P-44 4.3 3.5 2.7 2.4 2.0
DEEP WELL 3" SINGLE PIPE: 40 PSI
HMSD 3/4
17CP J32P-29 J34P-44 12.8 11.5 10.2 8.9 7.6 6.1
18CP J32P-24 J34P-44 7.8 6.9 6.0 5.3 4.5 3.6
16CP Factory
Installed 5.0 4.4 3.9 3.4 3.0 2.5 2.0
HMSE 1 7CP J32P-32 J34P-41 17.8 16.2 14.6 13.0 11.4 9.6 7.7
9CP J32P-26 J34P-41 10.7 9.8 9.0 7.9 6.7 5.8 5.0 4.1
HMSF 1-1/2
10CP J32P-38 J34P-45 21.7 19.7 17.9 15.9 14.0 11.0 8.0
9CP J32P-26 J34P-41 11.1 10.8 10.6 9.7 8.9 7.5 6.5 5.5
19CP Factory
Installed J34P-41 6.9 6.1 5.3 4.6 4.1
DEEP WELL 4" DOUBLE PIPE: 40 PSI
HMSD 3/4
CK2 J32P-29 J34P-44 12.8 11.5 10.2 8.9 7.6 6.1
CK2 J32P-24 J34P-44 7.8 6.9 6.0 5.3 4.5 3.6
15SD Factory
Installed 5.0 4.4 3.9 3.4 3.0 2.5 2.0
HMSE 1
CK3 J32P-32 J34P-41 17.8 16.2 14.6 13.0 11.4 9.6 7.7
CK3 J32P-26 J34P-41 10.7 9.8 9.0 7.9 6.7 5.8 5.0 4.1
CK1 J32P-20 J34P-43 5.0 4.5 3.9 3.5 3.0
HMSF 1-1/2
CK4 J32P-38 J34P-45 21.7 19.7 17.9 15.9 14.0 11.0 8.0
CK3 J32P-26 J34P-41 11.1 10.8 10.6 9.7 8.9 7.5 6.5 5.5
4SD Factory
Installed 6.9 6.1 5.3 4.6 4.1
S4511WS (05/20/13)
