542331 1 Goulds Pump And Control Panel Switches

542353 1 Goulds Pump And Control Panel Switches 542353_1_Goulds Pump and Control Panel Switches

542351 1 Goulds Pump And Control Panel Switches 542351_1_Goulds Pump and Control Panel Switches

542354 1 Goulds Pump And Control Panel Switches 542354_1_Goulds Pump and Control Panel Switches

542348 1 Goulds Pump And Control Panel Switches 542348_1_Goulds Pump and Control Panel Switches

542357 1 Goulds Pump And Control Panel Switches 542357_1_Goulds Pump and Control Panel Switches

: Pump 542331 1 Goulds Pump And Control Panel Switches 542331_1_Goulds Pump and Control Panel Switches pdf

Open the PDF directly: View PDF PDF.
Page Count: 8

CentriPro
PUMP / CONTROL PANEL
SWITCHES
CentriPro is a brand of ITT Corporation.
www.centripro.com
Engineered for life
CentriPro
®
ITT
Wastewater
BCPFS R7
2
CentriPro Pump / Control Panel Switches
A2T SERIES
SJE Double Float® Master Pump Switch
Features
• Mechanically activated, wide-angle switch
designed to control pumps up to 13 FLA,
78 LRA, 120 VAC or 240 VAC.
• This switch consists of two mechanical floats and
a splice tube. The splice tube contains a holding
relay which eliminates pump chatter in turbulent
conditions.
• Includes standard mounting clamps and boxed
packaging.
• Cable attached to float housing: flexible
16 gauge, 2 conductor (UL, CSA) SJOW,
water-resistant (CPE).
• Cable above splice: flexible 14 gauge, 3
conductor (UL, CSA) SJTW, water-resistant,
thermoplastic.
• Floats: 2.74" diameter x
4.83" long (7.0 x 12.3 cm) high impact,
corrosion resistant, PP housing for use in
sewage and non-potable water
up to 140º F (60º C).
• Not sensitive to rotation or turbulence.
• Pumping range: 10" to 56".
• Available for pump up or pump down ap-
plications.
• For confined applications requiring an ac-
curate pumping range.
• UL Recognized for use in non-potable water and sewage.
• CSA Certified.
• See chart for data and order numbers.
TERMS TO KNOW
Pump Switches are used to directly control the operation of a pump. They are normally wide-angle switches which means they
operate over a range of approximately 70º to 90º. Pump switches are available with piggyback plugs and with bare leads. Some can
also be used with control panels.
Control Switches are designed to only control pumps when used with a control or alarm panel. They cannot handle the high
starting amps and running amperage of a pump, only signal or control amperage.
NO or Normally Open is a switch with contacts that are open in the hanging position. They are used to pump down or empty a tank.
NC or Normally Closed is a switch with contacts that are closed in the hanging position. They are used to pump up or fill a tank.
®
®
A2X SERIES
MilliAmpMaster™ Mechanical Float Switch
Features
• Mechanically activated, snap-action, sealed
gold cross-point contacts are designed to
activate low current control panels and
alarms.
• Narrow angle Control for Low Voltage AC
or DC applications.
• Operate with differential of 45º above or
below horizontal.
• Electrical Load – low current
non-arcing applications
• 125 VAC – Max. Load .1 amps (Min.
Load .16 milliamps)
• 30 VDC – Max. Load .1 amps (Min.
Load .16 milliamps)
• 5 VDC - Minimum Load 1 milliamp
• UL Listed for use in non-potable water and sewage.
• CSA Certified
• Mounting clamp for attaching to discharge pipe is standard.
• Not sensitive to rotation.
• Maximum submergence or water depth, 30' (9 meters), 13 psi.
• Flexible 18 gauge, 2 conductor SJOW water resistant cable.
• Impact and corrosion resistant, polypropylene float housing for
use in sewage and water up to 140 º F.
• Use with Intrinsically Safe Barriers (as used with explosion-
proof pumps), PLC’s, solar applications and other low current
control panel or alarm applications.
• Cable lengths of 10', 20' and 30'.
• Standard order numbers are for Normally Open (NO) switches.
• Normally Closed (NC) or Pump Down switches are available as
a special order by adding a ”U” suffix. See Nomenclature on
last page.
• Float comes with blue cap for easy identification.
3
CentriPro Pump / Control Panel Switches
A2D SERIES
SJE PumpMaster® Pump Switch
Features
• Mechanically activated, heavy duty contacts,
wide angle operation.
• Passed NSF standard 61 protocol by an ap-
proved Water Quality Association laboratory.
•Controls pumps up to 1/2 HP at 120 VAC
and 1 HP at 230 VAC.
• Non-corrosive PVC housing for use in
liquids up to 140º F (60º C).
• Not sensitive to rotation or turbulence.
• Pumping range: 7" to 36".
• 16 AWG, SJOW cord is available
with or without piggyback plug.
• Available as pump up, pump
down and SPDT models, see
Nomenclature Chart.
• For potable water, water or sewage
applications.
• UL Recognized for use in water and sewage.
• CSA Certified.
• See chart for amperage range and other data.
A2E SERIES
SJE PumpMaster Plus® Pump Switch
Features
• Controls pumps up to 3⁄4 HP at 120 VAC and 2 HP at 230 VAC.
• 14 AWG, SJOW cord is available with or without piggyback plug.
•
All other features are the same as A2D PumpMaster Series
above.
A2HT SERIES
High Temperature Float Switch
Features
• Temperature Rating: 221º F (105º C)
• Wide Angle Switch: contacts open @ 45º below horizontal and
close at 45º above horizontal
• Float Material: PC/ABS (Polycarbonate ABS)
• Cord Material: Teflon coating
• Ratings: 13 Maximum Amps, ½ HP, 115/230 V
• Float Dimensions: 4.63" Long x 2.63" Diameter
• Nomenclature: see last page
• Available lengths: 20', 30' and 50' *
* No other lengths available in this Series.
A2KM23WP3
Conery Mechanical Float Pack of 3
Features
• Pack of three floats
• Narrow angle control for panel hookup
• 15' cord - Type SJOOW 16/2 have leads
• Float material: ABS material
• 5º contact closes
• Pump down operation
Ratings
• 10 Amp rating
• Mechanically activated
• Temperature Rating: Maximum temperature 190º F (88º C)
®
®
®
®
4
CentriPro Pump / Control Panel Switches
A2G SERIES
SJE AmpMaster® Pump Switch
Features
• Mechanically activated, heavy duty contacts,
wide angle operation.
• Controls pumps up to 11⁄2 HP at 115 VAC
and 3 HP at 250 VAC.
• Non-corrosive PVC housing for use in
liquids up to 140º F (60º C).
• Maximum pump running current of
20 amps.
• Not sensitive to rotation or turbulence.
• Pumping range: 9" to 24".
• 12 AWG, SJOW cord is available
only with bare leads.
• Available for pump down
applications only.
• UL Recognized for use in non-
potable water and sewage.
• CSA Certified.
• See chart for amperage
range and other data.
A2P SERIES
SJE MicroMaster® Plus
Features
• Mechanically activated, snap action contacts, wide angle.
• Pump down operation (optional pump up available)
• UL Recognized for use in non-potable water and sewage.
• CSA Certified.
• See chart for amperage range and other data.
• Controls pump up to 1 HP at 115 VAC and 1.5 HP at 230 VAC
• 16 AWG, SJOW cord
• Pumping range: 8" to 36"
A2H SERIES
SJE VerticalMaster® Pump Switch
Features
• Mechanically activated vertical
operation.
• Controls pumps up to 1⁄2 HP at
120 VAC and 1 HP at 230 VAC.
• Non-corrosive PVC housing for use
in liquids up to 140º F (60º C).
• Overall Dimensions: 12" High,
5" Deep, 3" Wide.
• Not sensitive to rotation.
• Pumping range: .75" to 6.5".
• 16 AWG, SJOW cord is available
with or without piggyback plug.
• Available for pump down
applications only.
• For confined applications requiring
an accurate pumping range.
• Stainless steel mounting bracket and hose clamp.
• UL Recognized for use in non-potable water and sewage.
• CSA Certified.
• See chart for amperage range and other data.
A2J SERIES
SJE VerticalMaster® II Pump Switch
Features
• Mechanically activated vertical operation.
• Maximum running 10 amps.
• Non-corrosive PVC housing for use in liquids up to
140º F (60º C).
• Overall Dimensions: 12" High, 5" Deep, 3" Wide.
• Not sensitive to rotation.
• Pumping range: .75" to 6.5" (pump down only)
• 18 AWG, SJOW cord
• For confined applications requiring an accurate pumping
range.
• Stainless steel mounting bracket and hose clamp.
• UL Recognized for use in non-potable water and sewage.
• CSA Certified.
• See chart for amperage range and other data.
®
®
®
®
5
CentriPro Pump / Control Panel Switches
A2N SERIES
SJE SignalMaster® Control Switch
Features
• Mechanically activated, narrow angle,
designed to activate pump control panels
or alarms.
• Not designed for direct connection to pump.
• Passed NSF standard 61 protocol by an
approved Water Quality Association
laboratory.
• Non-corrosive PVC housing for use in
liquids up to 140º F (60º C).
• Not sensitive to rotation.
• Control differential: 1.5" above or
below horizontal.
• Available as NO (pump down), NC (pump up) or SPDT model,
see Nomenclature page.
• For potable water, water or sewage applications.
• Supplied with a pipe clamp for mounting to pipe.
• UL Listed for use in water and sewage.
• CSA Certified.
• See chart for amperage range and other data.
• Normally open - comes with yellow cap for easy identification.
• Normally closed - comes with white cap for easy identification.
• Single pole double throw - comes with green cap for easy
identification.
A2WT SJ ELECTRO WEIGHT
• Adjustable snap in design.
• Works with all float switches shown.
• PVC
A2S SERIES
CentriPro® Diaphragm Pump or Control Switch
Features
• Mechanical contacts.
• Cast iron housing and BUNA-N diaphragm.
• For use in liquids up to 104º F (40º C).
• Control differential: pump turns on at 18" and off at 12"
submergence.
• 18/3 AWG, SJTW cord w/breather tube is available with or
without piggyback plug.
• Available only as NO for pump down operation.
• For wastewater or sewage applications.
• Supplied with a mounting bracket for mounting to pump.
• See chart for amperage range and other data.
A2WTC CONERY WEIGHT
• Zinc plated cord weight
• Works with all float switches
UL
®
®
6
CentriPro Pump / Control Panel Switches
PUMP SWITCHES (WIDE ANGLE) can be connected directly to a pump.
CONTROL SWITCHES (NARROW ANGLE) can only be used with control panels or alarm panels.
ORDER MAXIMUM MAXIMUM CORD LENGTH BARE PUMP CONTROL (1) (2) MOUNTING
NUMBER RUNNING AMPS STARTING AMPS (FEET) LEADS SWITCH SWITCH N.0. N.C. STRAP WEIGHT
A2D13 13 85 10 X X — X X
A2D23U 13 85 15 X X — X X
A2D23W 13 85 15 X X — X X
A2D33 13 85 20 X X — X X
A2D33U 13 85 20 X X — X X
A2D33W 13 85 20 X X — X X
A2D53W 13 85 30 X X — X X
A2D63W 13 85 50 X X — X X
A2D83W 13 85 100 X X — X X
A2E23 15 85 15 X X — X X
A2E23U 15 85 15 X X — X X
A2E33 15 85 20 X X — X X
A2E53 15 85 30 X X — X X
A2E53U 15 85 30 X X — X X
A2E63 15 85 50 X X — X X
A2E63U 15 85 50 X X — X X
A2E73 15 85 75 X X — X X
A2E83 15 85 100 X X — X X
A2G33 20 120 20 X X — X X
A2G43 20 120 25 X X — X X
A2G53 20 120 30 X X — X X
A2G63 20 120 50 X X — X X
A2HT33 13 58 20 X X X X X
A2HT53 13 58 30 X X X X X
A2HT63 13 58 50 X X X X X
A2N13 5 N/A 10 X — X X X
A2N33 5 N/A 20 X — X X X
A2N33U 5 N/A 20 X — X X X
A2N93 5 N/A 125 X — X X X
A2S23① 10 N/A 15 X — X X X
A2S53① 10 N/A 30 X — X X X
A2S63① 10 N/A 50 X — X X X
A2X13 See description N/A 10 X — X X X
A2X33 See description N/A 20 X — X X X
A2X53 See description N/A 30 X — X X X
N.O. (1) = PUMP DOWN
N.C. (2) = PUMP UP
① Diaphragm switch with 6" differential.
7
CentriPro Pump / Control Panel Switches
WIDE ANGLE 115 VOLT PIGGYBACK FLOAT SWITCHES TO DIRECTLY CONTROL PUMPS
ORDER MAXIMUM START 115 V CORD LENGTH (1) (2) MOUNTING
NUMBER AMPS AMPS PLUG FEET N.0. N.C. STRAP
A2D11 13 85 X 10 X X
A2D31 13 85 X 20 X X
A2D51 13 85 X 30 X X
A2D61 13 85 X 50 X X
A2E21 15 85 X 15 X X
A2E31 15 85 X 20 X X
A2E31U 15 85 X 20 X X
A2E51 15 85 X 30 X X
A2E61 15 85 X 50 X X
A2H11 13 60 X 10 X X
A2H31 13 60 X 20 X X
A2J11 15 85 X 10 X X
A2J21 15 85 X 15 X X
A2J31 15 85 X 20 X X
A2P01 13 78 X 10 X X
A2P21 13 78 X 15 X X
A2P31 13 78 X 20 X X
A2P51 13 78 X 30 X X
A2S21 13 60 X 15 X X
A2T31 13 78 X 20 X X
A2T51 13 78 X 30 X X
WIDE ANGLE 230 VOLT PIGGYBACK FLOAT SWITCHES TO DIRECTLY CONTROL PUMPS
ORDER MAXIMUM START 230 V CORD LENGTH (1) (2) MOUNTING
NUMBER AMPS AMPS PLUG FEET N.0. N.C. STRAP
A2D12 13 85 X 10 X X
A2D32 13 85 X 20 X X
A2E22 15 85 X 15 X X
A2E32 15 85 X 20 X X
A2E32U 15 85 X 20 X X
A2E52 15 85 X 30 X X
A2E62 15 85 X 50 X X
A2H12 12 60 X 10 X X
A2H32 12 60 X 20 X X
A2J12 10 60 X 10 X X
A2J22 10 60 X 15 X X
A2S22 13 60 X 15 X X
A2T32 13 78 X 20 X X
A2T52 13 78 X 30 X X
N.O. (1) = PUMP DOWN
N.C. (2) = PUMP UP
NOMENCLATURE
1st and 2nd Characters
A2 = Float Switch
3rd Character
D = PumpMaster® – SJE
E = PumpMaster Plus® – SJE
G = AmpMaster® – SJE
H = VerticalMaster® – SJE
J = VerticalMaster® II – SJE ➁
N = SignalMaster™ – SJE
P = MicroMaster® Plus – SJE ➁
R = MicroMaster® – SJE ➁
S = C I Diaphragm Level Switch – MP
T = Double Float® Master – SJE
X = MilliAmpMaster™
4th Character
1 = 10'
2 = 15' ➀
3 = 20'
4 = 25' ➀
5 = 30'
6 = 50'
7 = 75'
8 = 100'
9 = 125'
5th Character
1 = 115 V piggyback
2 = 230 V piggyback
3 = Bare lead
4 = Single pole double throw (SPDT)
6th Character (optional)
U = Pump Up or Normally Closed (NC)
W = A2WT Cable Weight
B = Bulk Packed (internal only)
Characters 1-4
A2HT = High Temperature Float Switch
A2KM = Conery 3 pack
Character 5 *
Length (ft)
2 = 15' (Conery only)
3 = 20'
5 = 30'
6 = 50'
Character 6
1 = 115V Piggyback Plug
2 = 230V Piggyback Plug
3 = Bare Leads
4 = Single Pole Double Throw (SPDT)
Characters 7, 8, 9
PK3 = Pack of three
* No other lengths available in this Series.
➀
Only available on existing models.
➁
Discontinued models – contained mercury.
Only available on select
control switches.
CentriPro
®
ITT
2881 East Bayard Street, Seneca Falls, NY 13148
Phone: (315) 568-7123 • Fax: (315) 568-7973
www.centripro.com
Junior Super Single®, Super Single®, PumpMaster®, PumpMaster Plus®, AmpMaster®, MilliAmp-
Master™, VerticalMaster®, VerticalMaster® II, Sensor Float®, Sensor Float® Mini, SignalMaster®,
MicroMaster®, and MicroMaster® Plus are registered trademarks and tradenames of SJ Electro
Systems, Inc. Double Float® Master is a registered trademark of SJE-Rhombus® Controls.
CentriPro is a registered trademark of ITT Corporation. ITT, the Engineered Blocks Symbol and Engi-
neered for Life are registered trademarks of ITT Manufacturing Enterprises, Inc.
Copyright © 2010 ITT Corporation BCPFS R7 April, 2010 Printed in U.S.A.
SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE. Engineered for life
ITT

Navigation menu