Pycom LOPY01R Triple Network (LoRa, WiFi and Bluetooth) IoT development Module powered by MicroPython User Manual
Pycom Ltd Triple Network (LoRa, WiFi and Bluetooth) IoT development Module powered by MicroPython Users Manual
Pycom >
Users Manual
L01 OEM Module
With LoRa, Wi and BLE, the L01 OEM Module is the only
triple bearer MicroPython enabled micro controller on the
market today – the perfect enterprise grade IoT plaorm for
your connected Things. With the latest Espressif chipset the L01
oers a perfect combinaon of power, friendliness and exibility.
Create and connect your things everywhere. Fast.
- Espressif ESP32 chipset
- Dual processor + WiFi radio System on Chip.
- Network processor handles the WiFi connecvity and the IPv6
stack.
- Main processor is enrely free to run the user applicaon.
- An extra ULP-coprocessor that can monitor GPIOs, the ADC
channels and control most of the internal peripherals during
deep-sleep mode while only consuming 25uA.
- Powerful CPU, BLE and state of the art WiFi radio. 1KM Wi
Range
- Can also double up as a Nano LoRa gateway
- MicroPython enabled
- Fits in a standard breadboard (with headers)
- Ultra-low power usage: a fracon compared to other connected
micro controllers
With dozens of ready to use templates and libraries soon to
be available on the Pycom Exchange, developing a new IoT
soluon is now easier and faster.
L01 Features
Use the Pymakr IDE
Super easy code editor to write your Python scripts
Quick Vericaon
For easy and fast debugging use the interacve shell that is
accessible through telnet or one of the serial ports
Easy Upload
Upload your scripts, and any other les you want to the L01 via
the FTP server
Locally or remotely
Reset the L01 (you can do it locally, or remotely via Telnet)
Mechanical
Processing
Hash / encryption
SHA, MD5, DES, AES
WiFi
802.11b/g/n 16mbps
Bluetooth
Low energy and classic
RTC
Running at 32KHz
- 2 x UART, 2 x SPI, I2C, I2S, micro SD card
- Analog channels: 8x12 bit ADCs
- Timers: 4x16 bit with PWM and input capture
- DMA on all peripherals
- GPIO: Up to 24
- Voltage Input: 3.3V regulated
- WiFi: 12mA in acve mode, 5uA in standby
- Lora: 15mA in acve mode, 10uA in standby
Interfaces
Power
Size: 40mm x 16mm x 2.7mm
Security & Certications
- SSL/TLS support
- WPA Enterprise security
- FCC - 2AJMTL01XXX
- CE
Memory
- RAM: 4MB
- Flash Memory: 8MB
- Hardware oang point
acceleraon
- Python mul-threading
- Node range: Up to 40km
- Nano-Gateway: Up to 22km
- Nano-Gateway Capacity: Up to 100 nodes
- Semtech LoRa transceiver SX1272
- LoRaWAN stack
- Class A and C devices
Range Speciction
LoRa Speciction
- 868 MHz (Europe) at +14dBm maximum
- 915 MHz (North and South America, Australia and New
Zealand) at +20dBm maximum
Operating Frequencies
8MB ash memory
LoRa transceiver
ESP32 Dual Core
Microcontroller and
WiFi/Bluetooth 4.2
radio
Operang temperature:
-40 to 85 degrees celsius
Distributed and manufactured by Pycom Ltd.
Registered oce:
High Point, 9 Sydenham Road, Guildford, Surrey GU1 3RX, UK
Copyright © 2017 by Pycom Ltd. All rights reserved. No part of this
document may be reproduced, distributed, or transmied in any form or
by any means, including photocopying, recording, or other electronic or
mechanical methods, without the prior wrien permission of Pycom Ltd,
except in the case of brief quotaons embodied in crical reviews and
certain other noncommercial uses permied by copyright law.
To order contact sales@pycom.io
EU Regulatory Conformance
Hereby, Pycom Ltd declares that the radio equipment type L01
OEM Module is in compliance with Direcve 2014/53/EU. The full
text of the EU declaraon of conformity is available at the following
internet address: www.pycom.io
Federal Communicaon Commission Interference
Statement
This device complies with Part 15 of the FCC Rules. Operaon is
subject to the following two condions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including
interference that may cause undesired operaon.
CAUTION: Changes or modicaons not expressly approved by the
party responsible for compliance could void the user's authority to
operate the equipment.
NOTE: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable
protecon against harmful interference in a residenal installaon.
This equipment generates uses and can radiate radio frequency
energy and, if not installed and used in accordance with
the instrucons, may cause harmful interference to radio
communicaons. However, there is no guarantee that interference
will not occur in a parcular installaon. If this equipment does
cause harmful interference to radio or television recepon, which
can be determined by turning the equipment o and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separaon between the equipment and receiver.
- Connect the equipment into an outlet on a circuit dierent from
that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
RF Warning Statement
To comply with FCC RF exposure compliance requirements, the
antennas used for this transmier must be installed to provide a
separaon distance of at least 20 cm from all persons and must not
be co-located or operang in conjuncon with any other antenna
or transmier.
This device is intended only for OEM integrators under the
following condions:
1) The antenna must be installed such that 20 cm is maintained
between the antenna and users, and
2) The transmier module may not be co-located with any other
transmier or antenna.
As long as two condions above are met, further transmier test
will not be required.
However, the OEM integrator is sll responsible for tesng
their end-product for any addional compliance requirements
required with this module installed. To ensure compliance with
all non-transmier funcons the host manufacturer is responsible
for ensuring compliance with the module(s) installed and fully
operaonal. For example, if a host was previously authorized as
an unintenonal radiator under the Declaraon of Conformity
procedure without a transmier cered module and a module is
added, the host manufacturer is responsible for ensuring that the
aer the module is installed and operaonal the host connues to
be compliant with the Part 15B unintenonal radiator requirements
The module is limited to OEM installaon ONLY. The module is
limited to installaon in mobile or xed applicaon. We hereby
acknowledge our responsibility to provide guidance to the host
manufacturer in the event that they require assistance for ensuring
compliance with the Part 15 Subpart B requirements.
IMPORTANT NOTE: In the event that these condions cannot
be met (for example certain laptop conguraons or co-locaon
with another transmier), then the FCC authorizaon is no
longer considered valid and the FCC ID cannot be used on the
nal product. In these circumstances, the OEM integrator will
be responsible for reevaluang the end product(including the
transmier) and obtaining a separate FCC authorizaon.
End Product Labeling
This transmier module is authorized only for use in device where
the antenna may be installed such that 20 cm may be maintained
between the antenna and users. The nal end product must be
labeled in a visible area with the following: “Contains FCC ID:
2AJMTL01XXX”. The grantee's FCC ID can be used only when all
FCC compliance requirements are met.
The following FCC part 15.19 statement has to also be available on
the label:
This device complies with Part 15 of FCC rules. Operaon is subject
to the following two condions:
(1) this device may not cause harmful interference and
(2) this device must accept any interference received, including
interference that may cause undesired operaon.
Manual Informaon to the End User
The OEM integrator has to be aware not to provide informaon to
the end user regarding how to install or remove this RF module in
the user’s manual of the end product which integrates this module.
In the user manual of the end product, the end user has to be
informed that the equipment complies with FCC radio-frequency
exposure guidelines set forth for an uncontrolled environment.
The end user has to also be informed that any changes or
modicaons not expressly approved by the manufacturer could void
the user's authority to operate this equipment.
The end user manual shall include all required regulatory
informaon/warning as show in this manual.
The maximum operang ambient temperature of the equipment
declared by the manufacturer is: -20~+85C
Receiver category 3