Pycom LOPY01R Triple Network (LoRa, WiFi and Bluetooth) IoT development Module powered by MicroPython User Manual

Download:
Mirror Download [FCC.gov]
Document ID	3605636
Application ID	lvemQzC5RlUJAKLI9LzOxA==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	87.51kB (1093836 bits)
Date Submitted	2017-10-16 00:00:00
Date Available	2017-10-17 00:00:00
Creation Date	2017-07-05 09:45:55
Producing Software	Adobe PDF Library 15.0
Document Lastmod	2017-07-05 09:45:57
Document Title	Users Manual
Document Creator	Adobe InDesign CC 2015 (Macintosh)

L01 OEM Module
With LoRa, Wifi and BLE, the L01 OEM Module is the only
triple bearer MicroPython enabled micro controller on the
market today – the perfect enterprise grade IoT platform for
your connected Things. With the latest Espressif chipset the L01
offers a perfect combination of power, friendliness and flexibility.
Create and connect your things everywhere. Fast.
Mechanical
Size: 40mm x 16mm x 2.7mm
Operating temperature:
-40 to 85 degrees celsius
ESP32 Dual Core
Microcontroller and
WiFi/Bluetooth 4.2
radio
8MB flash memory
L01 Features
- Powerful CPU, BLE and state of the art WiFi radio. 1KM Wifi
Range
- Can also double up as a Nano LoRa gateway
- MicroPython enabled
- Fits in a standard breadboard (with headers)
- Ultra-low power usage: a fraction compared to other connected
micro controllers
Processing
- Espressif ESP32 chipset
- Dual processor + WiFi radio System on Chip.
- Network processor handles the WiFi connectivity and the IPv6
stack.
- Main processor is entirely free to run the user application.
- An extra ULP-coprocessor that can monitor GPIOs, the ADC
channels and control most of the internal peripherals during
deep-sleep mode while only consuming 25uA.
Operating Frequencies
- 868 MHz (Europe) at +14dBm maximum
- 915 MHz (North and South America, Australia and New
Zealand) at +20dBm maximum
Range Specifiction
LoRa transceiver
Interfaces
- 2 x UART, 2 x SPI, I2C, I2S, micro SD card
- Analog channels: 8x12 bit ADCs
- Timers: 4x16 bit with PWM and input capture
- DMA on all peripherals
- GPIO: Up to 24
Security & Certifications Hash / encryption
- SSL/TLS support
- WPA Enterprise security
- FCC - 2AJMTL01XXX
- CE
Memory
- RAM: 4MB
- Flash Memory: 8MB
- Hardware floating point
acceleration
- Python multi-threading
SHA, MD5, DES, AES
WiFi
802.11b/g/n 16mbps
Bluetooth
Low energy and classic
RTC
Running at 32KHz
- Node range: Up to 40km
- Nano-Gateway: Up to 22km
- Nano-Gateway Capacity: Up to 100 nodes
Power
Use the Pymakr IDE
- Lora: 15mA in active mode, 10uA in standby
Super easy code editor to write your Python scripts
Quick Verification
For easy and fast debugging use the interactive shell that is
accessible through telnet or one of the serial ports
Easy Upload
Upload your scripts, and any other files you want to the L01 via
the FTP server
Locally or remotely
- Voltage Input: 3.3V regulated
- WiFi: 12mA in active mode, 5uA in standby
LoRa Specifiction
- Semtech LoRa transceiver SX1272
- LoRaWAN stack
- Class A and C devices
With dozens of ready to use templates and libraries soon to
be available on the Pycom Exchange, developing a new IoT
solution is now easier and faster.
Reset the L01 (you can do it locally, or remotely via Telnet)
Distributed and manufactured by Pycom Ltd.
Registered office:
High Point, 9 Sydenham Road, Guildford, Surrey GU1 3RX, UK
Copyright © 2017 by Pycom Ltd. All rights reserved. No part of this
document may be reproduced, distributed, or transmitted in any form or
by any means, including photocopying, recording, or other electronic or
mechanical methods, without the prior written permission of Pycom Ltd,
except in the case of brief quotations embodied in critical reviews and
certain other noncommercial uses permitted by copyright law.
To order contact sales@pycom.io
EU Regulatory Conformance
Hereby, Pycom Ltd declares that the radio equipment type L01
OEM Module is in compliance with Directive 2014/53/EU. The full
text of the EU declaration of conformity is available at the following
internet address: www.pycom.io
Federal Communication Commission Interference
Statement
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including
interference that may cause undesired operation.
CAUTION: Changes or modifications not expressly approved by the
party responsible for compliance could void the user's authority to
operate the equipment.
NOTE: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency
energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
RF Warning Statement
To comply with FCC RF exposure compliance requirements, the
antennas used for this transmitter must be installed to provide a
separation distance of at least 20 cm from all persons and must not
be co-located or operating in conjunction with any other antenna
or transmitter.
This device is intended only for OEM integrators under the
following conditions:
1) The antenna must be installed such that 20 cm is maintained
between the antenna and users, and
2) The transmitter module may not be co-located with any other
transmitter or antenna.
As long as two conditions above are met, further transmitter test
will not be required.
However, the OEM integrator is still responsible for testing
their end-product for any additional compliance requirements
required with this module installed. To ensure compliance with
all non-transmitter functions the host manufacturer is responsible
for ensuring compliance with the module(s) installed and fully
operational. For example, if a host was previously authorized as
an unintentional radiator under the Declaration of Conformity
procedure without a transmitter certified module and a module is
added, the host manufacturer is responsible for ensuring that the
after the module is installed and operational the host continues to
be compliant with the Part 15B unintentional radiator requirements
The module is limited to OEM installation ONLY. The module is
limited to installation in mobile or fixed application. We hereby
acknowledge our responsibility to provide guidance to the host
manufacturer in the event that they require assistance for ensuring
compliance with the Part 15 Subpart B requirements.
IMPORTANT NOTE: In the event that these conditions cannot
be met (for example certain laptop configurations or co-location
with another transmitter), then the FCC authorization is no
longer considered valid and the FCC ID cannot be used on the
final product. In these circumstances, the OEM integrator will
be responsible for reevaluating the end product(including the
transmitter) and obtaining a separate FCC authorization.
End Product Labeling
This transmitter module is authorized only for use in device where
the antenna may be installed such that 20 cm may be maintained
between the antenna and users. The final end product must be
labeled in a visible area with the following: “Contains FCC ID:
2AJMTL01XXX”. The grantee's FCC ID can be used only when all
FCC compliance requirements are met.
The following FCC part 15.19 statement has to also be available on
the label:
This device complies with Part 15 of FCC rules. Operation is subject
to the following two conditions:
(1) this device may not cause harmful interference and
(2) this device must accept any interference received, including
interference that may cause undesired operation.
Manual Information to the End User
The OEM integrator has to be aware not to provide information to
the end user regarding how to install or remove this RF module in
the user’s manual of the end product which integrates this module.
In the user manual of the end product, the end user has to be
informed that the equipment complies with FCC radio-frequency
exposure guidelines set forth for an uncontrolled environment.
The end user has to also be informed that any changes or
modifications not expressly approved by the manufacturer could void
the user's authority to operate this equipment.
The end user manual shall include all required regulatory
information/warning as show in this manual.
The maximum operating ambient temperature of the equipment
declared by the manufacturer is: -20~+85C
Receiver category 3

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.7
Linearized                      : No
Language                        : en-GB
XMP Toolkit                     : Adobe XMP Core 5.6-c123 79.158978, 2016/02/13-01:11:19
Create Date                     : 2017:07:05 09:45:55+01:00
Metadata Date                   : 2017:07:05 09:45:57+01:00
Modify Date                     : 2017:07:05 09:45:57+01:00
Creator Tool                    : Adobe InDesign CC 2015 (Macintosh)
Instance ID                     : uuid:5c6c1133-96ad-e54c-b5ab-d8c6c5f42c0b
Original Document ID            : xmp.did:57bcf50e-e41d-475a-a7ec-a451b2e2145e
Document ID                     : xmp.id:01c76d80-09d6-46aa-9a6e-ee93de3cdea3
Rendition Class                 : proof:pdf
Derived From Instance ID        : xmp.iid:eb94160d-8ee8-4b1b-9172-87d4cd7eeb68
Derived From Document ID        : xmp.did:35ee545b-ec7a-4528-9a41-a69d3d1d3025
Derived From Original Document ID: xmp.did:57bcf50e-e41d-475a-a7ec-a451b2e2145e
Derived From Rendition Class    : default
History Action                  : converted
History Parameters              : from application/x-indesign to application/pdf
History Software Agent          : Adobe InDesign CC 2015 (Macintosh)
History Changed                 : /
History When                    : 2017:07:05 09:45:55+01:00
Format                          : application/pdf
Producer                        : Adobe PDF Library 15.0
Trapped                         : False
Page Count                      : 2
Creator                         : Adobe InDesign CC 2015 (Macintosh)

EXIF Metadata provided by EXIF.tools