Q Global Solutions QBUN-D-RF0612 BUN-D RF control module User Manual

Q Global Solutions (Xiamen) Electronics Corp. BUN-D RF control module Users Manual

Users Manual

BUN-D-RF User Manual 1、Principle of system working 1.1 System connection 1BUN-D RF control moduleDigital Sensor extension cableDigital SensorA1A2A3A4B1B2B3B4RED REDBLACK BLACKREDGREENBLACKMomentory switch Dome Buzzer power lineLatching relay Dome Buzzer (RF)A1A2A3Control module power line2、System function power on，the system starts its self-diagnosis.a. No SENSOR：three beeps.b. one SENSOR：two beeps.c. two SENSOR：connect to CL、CR or L、R ,one beep；Three beeps for other conditions.Switch 1 OFF：Reverse systemSwitch 1 ON： Front systemSwitch 2 OFF：Reverse system，the maximum detection distance is 6ft；Front system，the maximum detection distance is 3ft.Switch 2 ON： Reverse sysytem，The maximum detection distance is 3ft.Front system. the maximum detection distance is 2ft.2.1 Self-diagnosis two-Sensor system (SENSOR1、SENSOR2）2.2 Front system/Reverse system shift 2.3 Corner SENSOR maximum detection distection shift
Obstacle position to its nearest sensor buzzer warning7ft-4ft(middle SENSOR)6ft-4ft(corner SENSOR)4ft-2ftwithin 2ftintemittent beepsRapid beepsSolid beep2.4 Detection distance 3ft-2ft itermittent beeps2ft-1ftwithin 1ftsolid beepRapid beepsbuzzer warningObstacle position to its nearest sensor2.4.1 2.4.2 To assure there is no false warning because of the fixity, the system should learn the enviroment. Learning method：after inatalling the sensor and control module，remove all obstacles in front or back of the vehicle. Power on, the system will warn if there is fixity. Then, power off. Redo "on-off" for four times.( "off" time < 3 seconds), if "off" is > 5 seconds, the learning process stops. No time limit for "on" time.) Wherein, the system enter learnig status, BUZZER beeps for 2 seconds, the system stores the fixity into its memory.(the fixity distance< 1m). There will be no false warning because of the fixity.Power on, LED of Momentary switch lights up , the system starts to work for 5 minutes, then shut off automatically.LED turns off.In operation time, press Momentary switch，the system shuts off at once. LED of Momentary switch turns off；When the system is in off satus，press Momentary switch，the system restart and work for five minutes.When LED flashes, it shows that sensor has some problems.Press the adjust switch, Buzzer beeps shortly, the volume from high to low, press again, the volume from low to high. The volume is stored everytmie the switch is pressed. The last volume remains until power on again. 2.5 Buzzer volume adjust 2.6 Fixity learning 2.7 Switch control function
3、System components 3.1 Control module Basic Specification 7. detection range4. Operating temperature5. store temperature6. output frequency3. Consume current2. Operating voltage1. Rating voltageSpecificationItemDC12VMAX40mA/12VDC9.6V--16V-30°C----+80°C40KHz ? à 2KHz-40°C---+85°C0~2ft~4ft~7ft8. Emiting frequency 433.92MHZ±75KHZ 3.2 Sensor and Sensor cable Vertical 50°±10°Plane 100°±20°5、Detecting angle7ft4、Maximum detection distance40KHz ± 2KHz3、input frequencyItem6、Detecting methodSpecification2、Store temperature1、Operating temperature-30°C----+80°C-40°C---+85°CUltrasonic 40KHz Basic Specification 3.3 Lathing relay rf dome buzzer and momentary switch -40°C---+85°Chigh：85±5 dB/10cm/12v-30°C----+80°CDC 9.6V--16VMAX40mA/12V12VParameterItem Basic Specificationlow：75±5 dB/10cm/12v1600Hz2、operating voltage range 3、Consume current4、temperature5、store temperature7、Volume frequency6、volume 1、Rating voltage
4 、Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Navigation menu