Qcom Technology LR802URN3 802.11b/g/n Wireless USB Module User Manual LR802URN3 Manual

Download:
Mirror Download [FCC.gov]
Document ID	2539664
Application ID	EXQLQdayaAD6E2rKFkQNVQ==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	90.13kB (1126679 bits)
Date Submitted	2015-02-23 00:00:00
Date Available	2015-02-23 00:00:00
Creation Date	2017-10-18 20:06:15
Producing Software	GPL Ghostscript 9.18
Document Lastmod	2017-10-18 20:06:15
Document Title	Microsoft Word - LR802URN3_Manual.doc
Document Creator	PScript5.dll Version 5.2.2
Document Author:	TING

802.11 b/ g/ n Wireless USB Module
LR802UKN3
U se r’s M a nua l
Qcom Technology Inc
I n st a lla t ion I n st r u ct ion s
**End Product Labeling:
The Final end product label must contain the following statement on the product label:
“Contains FCC ID: RUJ-LR802URN3
** End Product user’s manual:
The end product user manual must contain the following statements;
For Customers in the United States
"IMPORTANT NOTE: To comply with FCC RF exposure compliance requirements, the antenna
used for this transmitter must be installed to provide a separation distance of at least 20 cm from all
persons and must not be co-located or operating in conjunction with any other antenna or
transmitter."
A statement to caution the user that changes or modifications not expressly appproved by Appro
could void the user’s authority to operate the equipment. (Reference FCC Title 47 Section 15.21)
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device
may not cause harmful interference, and (2) this device must accept any interference received, including interference
that may cause undesired operation.
“This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.” (Reference FCC Title 47
Section 15.105)
Windows 7
Driver Installation
1.
For installing the Wireless LAN Card driver, go to the directory where the
Wireless Adapter Installation stored, then double-click the Setup program to
begin the installation.
2.
Realtek Wireless LAN Setup Wizard is preparing the setup. Click NEXT.
3.
The Realtek Wireless LAN driver is installing. Please wait.
4.
When the Realtek Wireless LAN – Install shield Wizard screen disappears, the
installation of Realtek Wireless LAN driver is now complete. Click Finish
5.
System Reboot.
6.
When you complete the installation, the utility icon will appear on the system
tray (
network settings.
). You could double-click it to configure wireless
Uninstalling the Wireless LAN Card
1.
For uninstalling the Wireless LAN Card, please go to: Control Panel 
Program and Features
2.
Under Windows environment. Right -click the "REALTEK Wireless LAN Driver
and Utility", and then click "Uninstall".
3.
Realtek Wireless LAN Setup Wizard prepares to uninstall the driver on your
system. Please wait.
4.
Click "Yes" to uninstall the Wireless LAN Card driver and utility.
5.
Wait for removing the driver and utility. After completing the uninstalling, click
the Finish.
Configuring the Wireless LAN Card
Double-click the utility icon
configuration.
in your system tray to begin the utility
Connecting to an existing network
1.
Click the Available Network Tab, all available Access Points would be listed.
Click on the desired Access Point, and click "Add to Profile".
2. Wireless Network Properties
2-1. Click “OK” if you connect to an unsecured network.
2-2. If you connect to a secured network please type the network security key or
passphrase and then click “OK”.
3.
Wireless network connection is completed ( see General Information Tab).
Windows 8
Driver Installation
1.
For installing the Wireless LAN Card driver, go to the directory where the
Wireless Adapter Installation stored, then double-click the Setup program to
begin the installation.
2.
Realtek Wireless LAN Setup Wizard is preparing the setup. Click NEXT.
3.
The Realtek Wireless LAN driver is installing. Please wait.
4.
When the Realtek Wireless LAN – Install shield Wizard screen disappears, the
installation of Realtek Wireless LAN driver is now complete. Click Finish
5.
System Reboot.
6. When you complete the installation, the utility icon will appear on the system
tray (
network settings.
). You could double-click it to configure wireless
10
Uninstalling the Wireless LAN Card
1、 For uninstalling the Wireless LAN Card, please go to: Control Panel 
Program and Features
2、 Under Windows environment. Right -click the "REALTEK Wireless LAN Driver
and Utility", and then click "Uninstall".
11
3、 Realtek Wireless LAN Setup Wizard prepares to uninstall the driver on your
system. Please wait.
4、 Click "Yes" to uninstall the Wireless LAN Card driver and utility.
5、 Wait for removing the driver and utility. After completing the uninstalling, click
the Finish.
12
Configuring the Wireless LAN Card
Double-click the utility icon
configuration.
in your system tray to begin the utility
Connecting to an existing network
1.
Click the Available Network Tab, all available Access Points would be listed.
Click on the desired Access Point, and click "Add to Profile".
2.
Wireless Network Properties
2-1. Click “OK” if you connect to an unsecured network.
13
2-2. If you connect to a secured network please type the network security key or
passphrase and then click “OK”.
3.
Wireless network connection is completed ( see General Information Tab).
14

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Encryption                      : Standard V4.4 (128-bit)
User Access                     : Extract
Author                          : TING
Create Date                     : 2015:02:10 11:01:20+08:00
Modify Date                     : 2015:02:23 17:28:14-08:00
XMP Toolkit                     : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26
Creator Tool                    : PScript5.dll Version 5.2.2
Metadata Date                   : 2015:02:23 17:28:14-08:00
Format                          : application/pdf
Title                           : Microsoft Word - LR802URN3_Manual.doc
Creator                         : TING
Producer                        : Acrobat Distiller 9.0.0 (Windows)
Document ID                     : uuid:f0f6b303-33e2-46ea-aa4f-d08e0c183174
Instance ID                     : uuid:759dc8a5-f685-40d9-b139-488d71546809
Page Count                      : 14

EXIF Metadata provided by EXIF.tools