Qixiang Electron Science and Technology 588V2 Land Mobile Radio User Manual

Qixiang Electron Science& Technology Co., Ltd Land Mobile Radio

user manual

588Land Mobile RadioFCC ID:T4K588V2
Do not attempt to configure your transceiver while driving,it is dangerous.This transceiver is designed for a 13.8V DC power supply. Don't use a 24V battery to power on the transceiver.Do not place the transceiver in excessively dusty, humid or wet areas, nor unstable surfaces.Please keep it away from interferential devices (such as TV, generator etc.) Do not expose the transceiver to long periods of direct sunlight nor place it close to heating appliances.If an abnormal odor or smoke is detected coming from the transceiver, turn OFF the power immediately. Contact an Anytone service station or your dealer.Do not transmit with high output power for extended periods; the transceiver may overheat.Please observe the following precautions to prevent fire, personal injury, or transceiver damage:Precautions
PowerCONTENTSNew and Innovative Features ..............................................1Supplied Accessories/Optional Accessories .....................2Supplied Accessories .......................................................................2Optional Accessories .......................................................................2Initial Installation ..................................................................3Mobile Installation ............................................................................3 DC Power Cable Connection ...........................................................4Power Supply Voltage Display .........................................................6Antenna Connection ........................................................................6Accessories Connections .................................................................7Getting Acquainted ..............................................................8Front panel .......................................................................................8Rear panel .......................................................................................9Display .............................................................................................9Microphone ......................................................................................10Working Mode(Amateur Transceiver or Professional Transceiver) ........................................................................11Basic Operations .................................................................12Switching the Power On/Off ............................................................12Adjusting the Volume ......................................................................12Switch between VFO and Channel mode .......................................12Adjusting Frequency/Channel Through Selector Knob ....................12Receiving .........................................................................................12Transmitting .....................................................................................12Transmitting Tone-Pulse ..................................................................13Transmitting Optional Signaling ......................................................13Channel Edit ....................................................................................13Channel Delete ................................................................................13Shortcut Operations .............................................................14Squelch Off/Squelch Off Momentary................................................14Squelch Level Setup ........................................................................14Frequency/Channel Scan ................................................................14Channel Scan ..................................................................................14CTCSS/DCS Encode and Decode Setup ........................................14CTCSS Scan ....................................................................................15DCS Scan ........................................................................................15 ............................................................15Compander (Decrease the background noise and enhance audio clarity ..................................................................................................15Offset Direction and Offset Frequency Setup ..................................16Keypad Lockout ...............................................................................16Current Voltage Enquiry ...................................................................16Auto-Dialer Setup .............................................................................16Transmitting Edited DTMF Tones in the Auto-dialer Memory ...........17General Setting .....................................................................18Frequency Channel Step Setup .......................................................18DTMF, DTMF ANI, 2Tone or 5Tone Signaling ..................................18Sending 2-Tone Call .........................................................................19Sending 5-Tone Call .........................................................................19Sending DTMF call ..........................................................................19Signaling Combination Setup ...........................................................19
CONTENTSTX OFF Setup ..................................................................................21Busy Channel Lockout .....................................................................21Editing Channel Name .....................................................................21Reverse TX/RX ................................................................................21Talk Around ......................................................................................22Voice Compander ...........................................................................22Radio's DTMF SELF ID ENQUIRY .................................................22Radio's 5TONE SELF ID ENQUIRY ...............................................23Voice Prompt ....................................................................................23TOT (Time-out timer) .......................................................................23APO (Auto power off) .......................................................................23DTMF Transmitting Time ..................................................................24Squelch Level Setup ........................................................................24Scan Dwell Time Setup ....................................................................24LCD Backlight ..................................................................................24Pilot Frequency ................................................................................25Display Mode Setup .........................................................................25PIN Setup ........................................................................................25Address List ....................................................................................26Factory Default .................................................................................26Microphone Operation .........................................................27Function Setup By Microphone Keypad ...........................................27Squelch Level ..................................................................................27Optional Signaling ...........................................................................27Scan Skip ........................................................................................28Frequency/Channel Scan ...............................................................28Busy Channel Lockout .....................................................................28Reverse TX/RX ................................................................................28 TOT (Time-out timer) ........................................................................29CTCSS/DCS Encode and Decode ...................................................29Talk Around .....................................................................................29Voice Prompt ....................................................................................29LCD Backlight .................................................................................30Long-distance Anti-theft Alarm ..........................................31Cable Clone ..........................................................................32Maintenance ..........................................................................33Default Setting after Resetting(VHF) ...............................................33Default Setting after Resetting(UHF) ...............................................33Trouble Shooting ..............................................................................33Specications .......................................................................34Attached Chart ......................................................................3550 groups CTCSS Tone Frequency(Hz) ..........................................351024 groups DCS Code. ..................................................................35
11New and Innovative Features588 Mobile Radio has nice housing, stoutness & stability, advanced and reliable functions, perfect & valuable. This amateur mobile radio especially designs for drivers and it pursues company philosophy of innovation and practicality. More functions as follows:Display on a large LCD with adjustable brightness, convenient for nighttime use. There are Amateur operation mode and Professional operation mode for option.Distribute buttons reasonably, convenient for operation. Adopt superior quality material, better technology and high quality radiator to ensure stable and durable operation.200 programmable memorized channels, identied by editing name. Programming different CTCSS, DCS, 2Tone, 5Tone in per channel, rejecting extra calling from other radios. Various scan functions including CTCSS/DCS Scan function. Using  5Tone to send Message, Emergency alarm, Call all, ANI, Remotely kill, Remotely Waken, etc.Automatic calling Identication function by DTMF--ANI or 5Tone--ANI .Compander function for decrease the background noise and enhance audio clarity, it can set compander ON/OFF per channel.Theft alarm provides extra safety. 
22Supplied Accessories/Optional AccessoriesSupplied AccessoriesOptional AccessoriesAfter carefully unpacking the transceiver, identify the items listed in the table below. We suggest you keep the box and packaging.TransceiverSpare Fuses (one pair)[QF-01]Cloning Cable (CP50)DesktopMicrophone(QDM-01)Alarm Cable A [QL-01(A)] Alarm Cable B (Extension line) [QL-01(B)]Car Antenna (QCA-01) USB Programming Cable (PC50) Cigar-Plug Connection Line (QCC-01) Programming Software (QPS-588) Regulated Power Supply (QRP-01)External Speaker (SP-01)User ManualMicrophone (QHM-03) (with DTMF keyboard) Mobile Mounting Bracket (QMB-01) DC Power Cable with Fuse Holder(QPL-01) Hardware Kit for BracketBlack screws (M4X8mm)4PCS(QSS-01A)Tapping screws (M5X8mm)4PCS(QSS-01B)S-Washer(QSS-01D)
3To install the transceiver, select a safe, convenient location inside your vehicle that minimizes danger to your passengers and yourself while the vehicle is in motion. Consider installing the unit at an appropriate position so that knees or legs will not strike it during sudden braking of your vehicle. Try to pick a well ventilated location that is shielded from direct sunlight.Install the mounting bracket in the vehicle using the supplied self-1. tapping screws (4pcs) and at washers (4pcs).Position the transceiver, then insert and tighten the supplied 2. hexagon SEMS screws. Double check that all screws are tightened to prevent vehicle  vibration from loosening the bracket or transceiver.3Car bodyWasher (M5)Tapping screw(M5x20mm)Mounting bracketInitial InstallationMobile installation Determine the appropriate angle of the transceiver, using the 3 screw hole positions on the side of the mounting bracket.
4Connect the DC power cable to the transceiver's power supply 6. connector.Press the connectors rmly together until the locking tab clicks.If the ignition-key on/off feature is desired(optional feature),use the 3RedBlackExt. Power jackDC power cableInitial InstallationDC Power Cable ConnectionMobile OperationIn many cars,the cigar-lighter plug is always powered. If this is the case, you cannot use it for the ignition key on/off function.The vehicle battery must have a nominal rating of 12V. Never connect the transceiver to a 24V battery. Be sure to use a 12V vehicle battery that has sufficient current capacity. If the current to the transceiver is insufficient, the display may darken during transmission, or transmitting output power may drop excessively.When the ignition key is turned to ACC or ON(Start) position with 7. the radio turned off, the power switch illuminates. The illumination will be turned off when the ignition key is turned to the off position. Route the DC power cable supplied with the transceiver directly 1. to the vehicle's battery terminals using the shortest path from the transceiver.We recommend you do not use the cigarette lighter socket as  some cigarette lighter sockets introduce an unacceptable voltage drop.The entire length of the cable must be dressed so it is isolated from heat, moisture, and the engine secondary (high voltage) ignition system/ cables.After installing cable, in order to avoid the risk of damp, please 2. use heat-resistant tap to tie together with fuse box. Don't forget to reinforce whole cable.In order to avoid the risk of short circuit, please cut down 3. connection with negative (-) of battery, then connect with radio.Confirm the correct polarity of the connections, then attach the 4. power cable to the battery terminals; red connects to the positive (+) terminal and black connects to the negative (-) terminal.Use the full length of the cable without cutting off excess even if  the cable is longer than required. In particular, never remove the fuse holders from the cable.Reconnect any wiring removed from the negative terminal.5. optional QCC-01(For Cigar-Plug connection) cable. Connect one of the cables between the ACC terminal or a Cigar-Plug that operates with the vehicle ignition or ACC switch on the vehicle and EXT POWER jack on the rear side of the unit.Locate the power input connector as close to the transceiver as possible.
53RedBlackRegulated power supply (QRP-01)DC power cable with fuse holder (QPL-01)Regulated power supply (QRP-01)Ext. Power jackACC terminalCigar-Plug connectionInitial InstallationBefore connecting the DC power to the transceiver, be sure to switch the transceiver and the DC power supply OFF.Do not plug the DC power supply into an AC outlet until you make all connections.In order to use this transceiver for xed station operation, you will need a separate 13.8V DC power supply (not included) , power supply( QRP-01) as optional accessories. Please contact local dealer to require.The recommended current capacity of your power supply is 12A.Connect the DC power cable to the regulated DC power supply 1. and ensure that the polarities are correct. (Red: positive, Black: negative).Do not directly connect the transceiver to an AC outlet. Use the supplied DC power cable to connect the transceiver to a regulated power supply.Do not substitute a cable with smaller gauge wires. To turn on the unit, press the power switch manually while it is illuminated. (While ignition key is at ACC or ON position)When the ignition key is turned to ACC or ON position with the 8. radio's power switch on, the unit turns on automatically and the power switch will be lit. Turn the ignition key to OFF position or manually turn the power switch off to shut down the radio.Using extra cable,power consumption:5MAH.9. Without this function,user can turn on/off radio by Power knob.10. Connect the transceiver's DC power connector to the connector 2. on the DC power cable.Press the connectors rmly together until the locking tab clicks .Fixed Station Operation
63Initial Installation REPLACING FUSESIf the fuse blows, determine the cause, then correct the problem. After the problem is resolved, replace the fuse. If newly installed fuses continue to blow, disconnect the power cable and contact your autho-rized dealer or an authorized servi-cecenter for assistance. Only use fuses of the specified type and rating, otherwise the transceiver could be damaged.After connecting the transceiver to the power supply, the supply voltage can be displayed on LCD by pressing the FUN key together with the key. The display immediately changes as the voltage supply changes, It also displays voltage during transmission.The transceiver will return to its normal operation when the power is switched ON or repeat above operation.Before operating, install an efcient, well-tuned antenna. The success of your installation will depend largely on the type of antenna and its correct installation. The transceiver can give excellent results if the antenna system and its installation are given careful attention.Use a 50Ω impedance antenna and low-loss coaxial feed-line that has a characteristic impedance of 50 Ω, to match the transceiver input impedance. Coupling the antenna to the transceiver via feed-lines having an impedance other than 50Ω reduces the efficiency of the antenna system and can cause interference to nearby broadcast television receivers, radio receivers, and other electronic equipment. Fuse Location Fuse Current RatingTransceiver 15ASupplied Accessory DC power cable 20AIf you use the transceiver for a long period when the vehicle battery is not fully charged, or when the engine is OFF, the battery may become discharged, and will not have sufcient reserves to start the vehicle. Avoid using the transceiver in these conditions.The range of displayed voltage is only from 7V to16V DC, because the displayed value is estimated, please use a voltmeter when a more precise reading is desired.Power supply voltage DisplayAntenna ConnectionImportantTransmitting without first connecting an antenna or other matched load may damage the transceiver. Always connect the antenna to the transceiver before transmitting.All xed stations should be equipped with a lightning arrester to reduce the risk of re, electric shock, and transceiver damage.The possible locations of antenna on a car are shown as following:
73SP-01SP-01 GroundMicrophone connectorMicrophone [QHM-03] Antenna [QCA-01]External speaker [SP-01]ErrorInitial Installation External Speaker MicrophoneIf you plan to use an external speaker, choose a speaker with an impedance of 8 Ω. The external speaker jack accepts a 3.5 mm (1/8")mono (2-conductor) plug.For voice communications, connect a microphone equipped with an 8-pin modular plug into the modular socket on the front of the main unit. Press rmly on the plug until the locking tab clicks. Attach the supplied microphone hanger in an appropriate location using the screws included in the screw set.External speaker adopt double port BTL, please care about the connecting way. The speaker can not connect with the ground, otherwise the speaker will be fault. The wrong connecting way as the following picture.Accessories Connections
MHz/SHIFT Switches Narrow band Switches power 84NO. KEY FUNCTION1Pow(Power) Power on/Off2VOL Adjust Volume Key3Main Dial Change frequency, memory channel and scan direction etc.4FUN/SET Function Key5V/M/MW Switches between VFO mode and Channel mode6MHz/SHIFT Step Size Key ( step:1MHz)7TS/DCS/LOCK Sets CTCSS and DCS value8CAL/H/L Call key9SQL/D Squelch off10 Data Terminal Data reading/writing, cloning and theft alarm functions11 TX lights during Transmitting12 Mic.connector Microphone connection portNO. KEY FUNCTION4FUN/SET Conrms the selective functions and exit5V/M/MW Stores data into channels6MHz/SHIFT Sets offset direction and offset frequency7TS/DCS/LOCK Sets Keypad lock function8CALtransmission9SQL/D Compander mode on/off NO. KEY FUNCTION1PWR Reset to factory default settings 5V/M/MW Erase the memory 67TS/DCS/LOCK Auto dialer 8CAL/H/L Enters clone data function mode9SQL/D Enters power supply voltage indication mode NO. KEY FUNCTION4FUN/SET Press and hold for 2s to enter the Setting mode 9SQL/D Monitor modeGetting AcquaintedFront panel Press key until icon appears then press the following key.Press key and following key together to activate following function:Functions that require continuous pressing following key to be activatedBasic Functions
9421NO. KEY FUNCTION1Ext. Power JackTerminal for connecting optional cable QCC01 for use with ignition key On/Off function.The radio will auto power on when car is driving. The radio will auto power off when car stops. 2Ext.Speaker Terminal Terminal for optional external speaker SP01 3Antenna Connector Connection for 50Ω coaxial cable and antenna.NO. KEYÅFUNCTION1 SQL Squelch level.2 MIn channel mode.3 Indicates the channel number in channel mode.4Decimal pointChannel skip.5Decimal point Indicates the decimal point of frequency and the scanning function.6 Indicates the frequency or memory name.7Signal is being received or monitor.8Signal strength of receiving and transmitting.9Compander.10 Keypad lock .11 DCS Set DCS function.12 Set CTCSS function.13 + _Offset frequency direction.14 Scramble.15 A Auto power off.16 Nar Narrow band.17 Pressing key.3Getting AcquaintedDISPLAYRear panel31213 101112144567891516171819 13
104NO. KEY FUNCTION1UP Increase frequency ,channel number or setting value.2DOWN Decrease frequency, channel number or setting value.3PTT Press the PTT (Push-TO-Talk) key to transmit.4Number Key Input VFO frequency or DTMF dial out etc..5DTMF ON/OFF Switches between DTMF dialing or function operating.6LOCK Switch Locks out the UP 、Down、Numerical keys and Function keys.7MIC Speak here during transmission.Key Pad Serial Data+5VDOWNUPMIC GNDMICPTTGNDmicrophone MIC Connector Diagram(in the front view of connector)Getting Acquainted
115According to practical application,you can set the radio works as Amateur Transceiver mode or Professional Transceiver mode . There are also 2 levels operation menu to set functions as you need. It is easy and convenient (From No.1 to No. 15 are channel function setup,From No.15 to No.29 are general setting setup). 1.  In PC software's "General Setting"menu ,choose "Display Mode" to select Amateur Transceiver mode or Professional Transceiver mode. :Please refer to "Display Mode" in Page 24.2. Except setting as "CH" mode, others considered as Amateur transceiver mode. Under this mode,press key to switch between Channel mode and VFO mode . Professional Transceiver Mode3. When set display mode as "CH",it enters into Professional Transceiver mode.At this mode,except scan,other shortcut operation can't operate.And from No.1-17 menu in function setting will be auto-hidden,They should be set by PC software.If there is corresponding name for current channel,the LCD will display current channel name Otherwise,it shows current channel number. (As pic 4) (As pic 5) Under every mode, from No. 18-29 menu in 4. general setting can be changed and saved.VFO Mode(Frequency mode)C. : This mode shows only frequency on the display. Shortcut operation and Channel setting will be changed & stored as the latest value permanently.Once the radio is turned off or changed to new VFO frequency, the latest setting is remained until next change.(As pic 3) If transceiver programmed as professional transceiver mode and locked,you can't return to amateur transceiver mode by manual operation from general setting.(Pic 2)(Pic 4)(Pic 5)Frequency + Channel modeA. : When set display as"FR",it enters into Frequency+Channel mode, new setting of channel operation and shortcut operation can be temporarily used by user. Once the radio is turned off or switched to another channel, the temporary setting will be erased and back to initial settings.(As pic 1)Channel+Name Tag ModeB. : When set display as "NM",it enters into Channel +Name Tag mode. At this mode, it will display corresponding channel name when the current channel is edited with name. Otherwise, it will display frequency + channel. Its operations are the same as frequency + channel mode.(As pic 2)(Pic 3)WORKING MODE (AMATEUR TRANSCEIVER OR PROFESSIONAL TRANSCEIVER)
12In standby, press key or Microphone's key until appear , this indicates current channel in channel mode. Repeat above 6PWR KEYDialFrequency decrease Frequency increaseVolume KnobMinVolume MaxVolumeBasic Operations Switching The Power On/OffAdjusting The Volume Switch between VFO and Channel modeAdjusting Frequency/Channel THROUGH SELECTOR KNOBReceivingaccording to the option selected during installation Press the switch or turn the ignition key to ACC (speed up) or ON (startup) position to power on radio . Press the key for 1s or turn the ignition key to OFF position to turn off.When the channel you are operating is called, the screen shows and field intensity, in this way, you can hear the calling from transmitting party.Under frequency (VFO) mode, you can 1. change the current frequency to the desired one through selector knob; Turn clockwise to increase frequency; turn counterclockwise to decrease. Every gear will increase or decrease one step. Press key, the decimal point of Turn the VOL knob clockwise to increase the audio level, counterclockwise to decrease. During communication, volume can be adjusted more accurate.If the transceiver has set at higher squelch level, it may fail to hear the calling.operation to switch between Frequency mode (VFO) and Channel mode.frequency in screen will be auto-hidden. In this status, turn selector knob or Microphone [ / ] key will increase or decrease frequency quickly by 1MHz step .Under channel mode, you can change the current channel to the 2. desired one through selector knob, clockwise turn to the forward channel, anticlockwise turn to the backward channel. In relative working mode, Microphone's [ / ] key has same function for adjusting frequency and channel.TransmittingPress and hold key or press MIC's key to monitor for a while to conrm the channel desired is not busy. Release or press Mic's key to return standby status,Then press and hold [PTT] key to speak into microphone.When the channel you are operating is called,the screen shows BUSY and field intensity,you can't hear the calling from transmitting party,it means current channel receives a matching carrier but unmatching signaling(Refer to CTCSS/DCS encode and decode or Optional Signaling setup).
13Basic Operations Transmitting Tone-PulseTransmitting OPTIONAL SIGNALING Press and hold [PTT] key, then press Microphone [ ] key to transmit current selected tone-pulse signal. Press and hold [PTT] key, then press Microphone key or press key in front panel or press Mic's key to transmit pre-stored and selected DTMF/2Tone/5Tone optional signaling.Channel EditChannel DeleteUnder frequency mode (VFO), turn 1. selector knob to select the desired frequency or input frequency by MIC's numeric keys.Press2. key to enter CTCSS/DCS signaling setup, turn selector knob to select the desired signaling.Press3. key, LCD appears , icon and current channel number, icon ashing means current channel is Under channel mode, turn selector knob to select channel which 1. you want to delete.Press2. key and key together, current channel will be deleted and emitted a prompt voice. icon ashing means current channel is deleted.empty.Turn selector knob to select the desired channel number to store.4. Press 5. key, , icon and channel number disappears and emit a prompt voice, thus the channel storage succeed.6Press and hold [PTT] key, LED lights RED and power intensity showed in screen indicates it is transmitting, release to receive.Please hold the microphone approximately 2.5-5.0cm from your lips , and then speak into the microphone in your normal speaking voice to get best timbre.
147Shortcut OperationsSquelch level SetupFrequency/Channel ScanChannel ScanCTCSS/DCS Encode and Decode setupSetting the radio to a tight squelch level,you can avoid unwanted signals or noise,but you may not receive a weak signal. Therefore,it will be better for you to select the normal squelch level.In frequency (VFO) mode, this function is designed to monitor signal of every communicative frequency point of transceiver "step size" you have set. In channel mode, this function is designed to monitor signal in every channel. In channel mode,Press 1. key for 1s to enter into channel scan Repeatedly press key to check whether set CTCSS/DCS encode and decode in current channel or not.When LCD appears1. iron, it means current channel with CTCSS encode, turn selector knob or press Microphone's [ / ] key to select desired CTCSS encode.When LCD appears2. and iron, it means current channel with CTCSS encode and decode, turn selector knob or press Microphone's [ / ] to select desired CTCSS code.While standby, press 1. key and turn selector knob until LCD appears and current squelch levelTurn selector knob or press MIC [ 2. / ] key to set desired squelch level.Press any key except 3. and key to exit . Frequency ScanIn VFO mode,press 1. for 1s to enter into frequency scan.Turn selector knob or press Microphone [ 2. / ] key to change scan direction.Press any key except 3. and key to exit.Turn selector knob or press Microphone 2. [ / ] key to change scan direction.Press any key except3. and key to exit. squelch off/squelch off momeNTARY key programmed as Squelch Off or Squelch Off Momentary to monitor the weak signal.Squelch Off: Press1. key to disable squelch ,press key again to resume squelch.Squelch Off Momentary: Press and hold2. key to disable squelch,release key to resume squelch.The above functions should be set in programme software.
157Shortcut OperationsCTCSS SCANRepeatedly press key until LCD displays and icons ,then hold key for 1S to enter into CTCSS scanning. Once nding a matching CTCSS signaling ,it will stop for 15s then scan again. Under channel mode,this operation can be temporarily used by user. Once the radio is turned off or switched to another channel,the temporary setting will be erased.When LCD appears 3. iron, it means current channe can be set with DCS encode and decode together, turn selector knob or press Microphone's [ / ] to select desired DCS encode and decode.CTCSS:62.5-254.1, Total 51groups; DCS:000N-777I total 1024 4. groups. N is positive code, I is inverse code.Press any key except 5. , and keys to return into standby status. Repeatedly press key until LCD displays DCS icons ,then hold key for 1S to enter into DCS scanning. Once nding a matching DCS signaling ,it will stop for 15s then scan again.compander function.Compander function will decrease the background noise and enhance audio clarity, especially in long range communication.Press1. key, then press key to turn on compander function, repeat above operation again to turn off Compander (Decrease the background noise and ENHANCE AUDIO CLARITY)When LCD appears 2. iron, enable compander in current channel.When LCD doesn't display 3. iron, disable compander in current channel.DCS SCAN
16Press key until LCD displays1. icon, then press key until, LCD displays icon, it indicates keypad lockout function is valid.This will automatically transmit pre-programmed and stored DTMF tones. And they are often used to remote control electronic devices or AUTOPATCH phone systems available on some repeater.Press and hold 1. key, then press key to enter the auto-dialer enquiry mode, LCD displays current default data and current group displayed on left. If no data in current group,it shows"EMPTY".Press and hold key, then press 1. key, LCD displays current battery voltage.Repeat above operation to return into 2. VFO or Channel modefrequency.When LCD displays " " icon, it indicates negative offset, which 4. means transmitting frequency lower than receiving frequency.Turn selector knob or Mic's [ 5. / ] key to change offset frequency, offset frequency changed as per stepping.Press any key except 6. and key to exit into standby.Press 1. key until the icon displays on the LCD, then press key, LCD displays offset direction and offset frequency.Repeatedly press key to select 2. positive offset and negative offset.When LCD displays " " icon, it indicates 3. positive offset, which means transmitting frequency higher than receiving 7Repeater receives a signal(UP-LINK) on one frequency and re-transmits on another frequency(DOWN-LINK). The difference between these two frequencies is called the offset frequency. If the UP-LINK frequency higher than DOWN-LINK frequency, the direction is positive, If it is lower, the shift direction is negative.Avoiding unintentional operation, this function will lock main keys, all keys except 、 and key are invalid.Offset Direction and offset frequency setup KEYPAD LOCKOUTCurrent Voltage ENQUIRYAuto-Dialer SetupShortcut OperationsIn voltage display mode, all functions and channel or frequency selection are invalid.This function will display Current Battery Voltage.Repeat above operation, 2. icon disappears, it indicates keypad lockout function is invalid.Under channel mode,this operation can be temporarily used by user. Once the radio is turned off or switched to another channel,the temporary setting will be erased.
17Turn selector knob to choose group you 2. desired. Total:16 group,01-16.7Shortcut OperationsPress3. key to enter into editing of current group,press MIC's numeric keys to set your desired data.The display scrolls when the 7th digit 4. is entered. The numbers 0-9, --, A-D, * and # can be stored up to a total of 23 digits.After editing,press PTT or5. key to send current group and store edited DTMF signaling. Press to exit and store.Press 1. key, then press key to enter into auto-dialer enquiryTurn selector knob to select desired 2. transmitting groupPress PTT or3. key to transmit current selected DTMF tones.Transmitting Edited DTMF tones in the Auto-dialer memory
18Press 2. / key to choose No.01 menu, LCD displays ”STP--125”Turn selector knob to select the desired frequency channel step.3. Channel step: 5K,6.25K,8.33K,10K,12.5K,20K,25K,30K and 50K, total 9 kinds.Press 4. key to conrm and exitPress and hold 1. key for over 2s to enter general setting menu.Press and hold1. key for over 2s to enter general setting menu.Press 2. or to select the desired function option.Turn selector knob to select the desired setup.3. Press4. to conrm and exit.Meanwhile,if you want to edit channel name or start up menu,press or to move forward or backward,Press to store and exit.Only in frequency (VFO) mode, this function is valid. Turn selector knob to select frequency or frequency scanning which is restricted by frequency step size. 8General SettingFrequency Channel Step SetupThis function is auto-hidden in channel mode. DTMF, DTMF ANI, 2Tone or 5Tone SignalingDTMF/5Tone/2Tone signalling function as similarily as CTCSS/DCS. Without receiving correspondent tone signalling, the speaker will remain mute. DTMF and 5Tone signalling can be applied for other advanced features such as ANI, PTT ID, group call, remotely stun,remotely kill, waken,...etc. The signalling edition must be done through programming software. Please refer to the HELP option in the programming software to know how to operate these features.Press and hold 1. key for over 2s to enter into general setting menu.Press 2. / to choose No 2 menu,LCD displays"T-OFF" .Turn selector knob to 3. select the desired setup."DTMF”: the channel will be mute by a DTMF signal. The speaker won’t be open until receiving a correspondent DTMF signal. Hold "PTT" then press [UP] or press directly to transmit the pre-stored DTMF signaling. In Profession transceiver mode,the functions from No.1 to No.17 will be auto-hidden.In DTMF signaling mode,press for 2s until LCD displays "AN---",turn selector knob to select desired digit(the other party ID).In this mode,press to confirm exist digit and move cursor to next,press to forward cursor.After editing,press key to operate ANI call."2TONE": the channel will be mute by a 2-Tone signal. The speaker won’t be open until receiving a correspondent 2-Tone signal.Hold “PTT” then press [UP] or press directly to transmit the pre-stored 2-Tone signaling."5Tone": the channel will be mute by a 5-Tone signal. The Speaker won’t be open until receiving a correspondent 5-Tone signal. hold “PTT” then press [UP] or
198Sending 5-Tone CallPress 2. / key to choose No.04 menu, LCD displays "5TON XX","XX"indicates the group in the list.Turn selector knob to select the desired 3. sending 5TONE group,Press PTT to transmit selected group. Total:100groups,00-99,Default:00.4. Press 5. key to conrm and exit. General SettingContent and name of 5TONE will be edited by programming software.This radio only query edited group or name.If there is corresponding name for 5TONE,this operation will display 5TONE corresponding name.Press directly to transmit the pre-stored 5-Tone signaling.In 5Tone signaling mode,press for 2s until LCD displays "AN---",turn selector knob to select desired digit(caller ID).In this mode,press to conrm exist digit and move cursor to next,press to forward cursor.After editing,press key to operate ANI call.Press 4. key to conrm and exit Sending 2-Tone CallPress and hold 1. key for over 2s to enter general setting menu.Press 2. / key to choose No.03 menu, LCD displays "2TON XX","XX"indicates the group in the list.Turn selector knob to select the desired 3. sending 2TONE group,Press PTT to transmit selected group. Total:32groups,00-31,Default:00.4. Press 5. key to conrm and exit. Content and name of 2TONE will be edited by programming software.This radio only query edited group or name.If there is corresponding name for 2TONE,this operation will display 2TONE corresponding name.Press and hold1. key for over 2s to enter general setting menuSending DTMF callPress and hold 1. key for over 2s to enter general setting menu.Press 2. / key to choose No.05 menu, LCD displays "DTMF XX","XX"indicates the group in the list.Turn selector knob to select the desired 3. sending DTMF group,Press PTT to transmit selected group. Total:16groups,00-16,Default:00.4. Press 5. key to conrm and exit.Signaling Combination setupThis function is to improve the level of protecting the radio against receiving irrelative signal.
208Turn selector knob to select the desired 3. combinationIf select "SQ",it indicates you can hear the calling from caller when receive a matching carrier.If LCD displays "CTC",it indicates you can hear the calling from caller when receive a matching carrier and CTCSS/DCS signaling .If LCD displays "TON",it indicates you can hear the calling from caller when receive a matching carrier and DTMF/2TONE/5TONE signaling .If LCD displays "C/T",it indicates you can hear the calling from caller when receive a matching carrier and CTCSS/DCS and DTMF/2TONE/5TONE signaling .If LCD displays "C/T",it indicates you can hear the calling from caller when receive a matching carrier and either CTCSS/DCS DTMF/2TONE/5TONE signaling. .Press 4. key to conrm and exit General SettingPress and hold 1. key for over 2s to enter general setting menu.Press 2. / key to choose No.06 menu, LCD displays "SPK--SQ".This setting will be set together with adding optional signaling and CTCSS/DCS.
218TX OFF SETUPDisable this function,it is invalid to press PTT,current channel only works in RX mode.Press and hold 1. key for over 2s to enter general setting menu.Press 2. / key to choose No.09 menu, LCD displays"TX-ON".Turn selector knob to select the desired 3. setting .On:In current channel,Press PTT to transmit OFF:In current channel,Press PTT is invalid.Press 4. key to conrm and exit.Default:ON.Busy Channel LockoutBCLO is to disable transmitting while RX signal is received. Once the channel is busy and you press PTT, the radio will beep as warning and get back to receiving.Press and hold 1. key for over 2s to enter general setting menuPress 2. / key to choose No.10 menu, LCD displays"LOCK--OFF".Turn selector knob to select the desired 3. setting.BU: Enable BCLO, Carrier lockout, transmitting is inhibited when current channel receives a matching carrier;press [PTT] to emit error voice prompt and back to receiving status.RL: Enable BTLO, transmitting is inhibited when current channel receives a matching carrier but dis-matching CTCSS/DCS.press [PTT] to emit error voice prompt and back to receiving status.OFF: Busy channel lockout is disabled.It can transmit in any receiving status.Press 4. key to conrm and exit.Press and hold 1. key for over 2s to enter general setting menu.Press 2. / key to choose No.11 menu, LCD displays cursor and ashing.Turn selector knob to select the desired letter,press 3. key to conrm selected letter and enter into next edition,Press to return forward edition.After edition,press 4. key to exit.Reverse TX/RXGeneral SettingEditing Channel NAME In Frequency (VFO) mode ,this function will be auto-hidden.TX frequency turns to RX frequency & RX frequency changes to TX frequency. The signaling will also be reversed if CTCSS/DCS signaling exited in this channel.Press and hold 1. key for over 2s to enter general setting menu
228Press 2. / key to choose No.12 menu, LCD displays "REV—OF".Turn selector knob to select the desired 3. setting. ON:Enable Frequency Reverse OFF:Disable Frequency Reverse.After edition,press 4. key to exit.Talk Around Press 2. / key to choose No.14 menu, LCD displays”COMP--OFF”.Turn selector knob to select the desired 3. setting. ON:Enable compander OFF:Disable companderPress 4. key to conrm and exit.Default:OFFGeneral SettingBy Talk Around function,you can directly communicate with other radios in your group in case the repeater is not activated or when you are out of the repeater range. The transceiver will transmit by RX frequency with its CTCSS/DCS signaling.Press and hold 1. key for over 2s to enter general setting menu.Press 2. / key to choose No.13 menu, LCD displays "TALK—OF".Turn selector knob to select the desired 3. setting. ON:Enable Talk Around OFF:Disable Talk AroundAfter edition,press 4. key to exit.Voice Compander Enable this function to reduce background noise and enhance audio clarity, especially in long range communication.Press and hold1. key for over 2s to enter general setting menuRadio's DTMF SELF ID ENQUIRY Press and hold1. key for over 2s to enter general setting menu.Press 2. / key to choose No.16 menu, LCD displays”D--XXX” XXX is radio's DTMF SELF ID. Press 3. key to conrm and exit.
238Radio's 5TONE SELF ID ENQUIRYPress and hold1. key for over 2s to enter general setting menu.Press 2. / key to choose No.17 menu, LCD displays"F--XXXXX", "XXXXX" is radio's 5TONE SELF ID. Press 3. key to conrm and exit.Voice PromptThe prompting tone provides confirmation of entry, error status or malfunctions of the transceiver. You can enable or disable this function.Press and hold1. key for over 2s to enter general setting menu.Press 2. / key to choose No.18 menu, LCD displays"BEEP--ON".Turn selector knob to select the desired 3. setting. ON:Enable voice prompt OFF:Disable voice promptPress 4. key to conrm and exit.Default:ON.TOT (Time-out timer)The time-out timer limits the amount of transmitting time. When you reach the time limit which has been programmed by your dealer, your transmission will be cut off. In order to transmit again, you must release PTT button to reset the timer.Press and hold1. key for over 2s to enter general setting menu.Press2. / key to choose No.19 menu, LCD displays"TOT--3"Turn selector knob to select the desired 3. setting. Timer:1-30min,each level 1min OFF:Disable TOTPress 4. key to conrm and exit.Default:3.APO (Auto power off)Once APO is activated, the radio will be automatically switched off when the pre-set timer is running to end.Press and hold1. key for over 2s to enter general setting menu.Press 2. / key to choose No.20 menu, LCD displays"APO--OFF".Turn selector knob to select the desired 3. setting. 30MIN:Auto power off after 30mGeneral SettingSuggestion:Enable this function to check incorrect operation and malfunctions.
248 1HOUR:Auto power off after 1h 2HOUR:Auto power off after 2h OFF:Disable Auto power offPress 4. key to conrm and exit.Default:OFFDTMF Transmitting TimePress and hold 1. key for over 2s to enter general setting.Press2. / key to choose No.21 menu, LCD displays"SPD--50".Turn selector knob to select the desired setting. 3. 30/50/100/200/300/500, which indicates the time for sending each DTMF signal & the interval between each DTMF being sent.Press 4. key to conrm and exit.Default:50MS.Squelch level SetupSetting the radio to a tight squelch level, you can avoid unwanted signals or noise, but you may not receive a weak signal. Therefore, it will be better for you to select the normal squelch levelPress and hold1. key for over 2s to enter general setting menu.Press2. / key to choose No.22 menu, LCD displays"SQL--04".Turn selector knob to select the desired squelch level.3. OF-20 total 21,OF is min setting value(ON)Press 4. key to conrm and exit.Default:04Scan Dwell Time SetupThere are 3 kinds of Scan Dwell Time for option.Press and hold1. key for over 2s to enter general setting menu.Press 2. / key to choose No.23 menu, LCD displays"SCAN--TO".Turn selector knob to select the desired 3. Scan Dwell Time.TO:it pauses 15s once scanning a matching signal,then resume scan.CO:it pauses once scanning a matching signal,signal disappeared then resume scan.SE:It stops once scanning a matching signal.Press 4. key to conrm the selection and exit.Default:TO.LCD BacklightPress and hold1. key for over 2s to enter general setting menu.Press 2. / key to choose No.24 General SettingPress ,then turn selector knob also can select the desired squelch level.If the transceiver has set at higher squelch level,it may fail to hear the calling.If set at lower squelch level,the radio will be interfered.
258menu, LCD displays"LAMP--25"Turn selector knob to select the desired LCD backlight brightness 3. 1-32 total 32 level backlight brightness.Press 4. key to conrm and exit.Default:25.Pilot FrequencyThis function uses to start repeater .It needs a certain intensity Pilot Frequency to start dormant repeater.As usual,no need to send pilot frequency again once repeater started.Press and hold1. key for over 2s to enter general setting. Press2. / key to choose No.25 menu, LCD displays"TB--1750".Turn selector knob to select the desired 3. pilot frequency.1750HZ:Pilot frequency1750HZ2100HZ:Pilot frequency 2100HZ1000HZ:Pilot frequency 1000HZ1450HZ:Pilot frequency 1450HZPress 4. key to conrm the selection and exit.Default:1750HZDisplay Mode SetupThere are 3 different dispaly modes: Frequency+Channel mode,& Channel mode&Channel+Name Tag mode, .Press and hold1. key for over 2s to enter general setting menu.Press 2. / key to choose No.26 menu, LCD displays"DSP—FR".Turn selector knob to select the desired 3. mode.FR:Frequency+Channel mode(Amateur transceiver mode).CH:Channel mode(Professional transceiver mode).NM:Channel+Name Tag mode(Amateur transceiver mode),if channel not named,it displays Frequency+Channel mode.Press 4. key to conrm and exit.Default:FR.PIN Setup Enable this function,you have to insert a matching PIN to enter into normal status when radio is turned on.(Pin setup by programme software).Press and hold1. key for over 2s to enter general setting menu.Press 2. / key to choose No.27 menu, LCD displays"CODE-OF".Turn selector knob to enable/disable 3. Pin setup. ON: Turn on Pin setup OFF:Turn off Pin setupPress 4. key to conrm and exit.Default:OFFThis function will be auto-hidden if channel mode locked.(Refer to programme software)General Setting
268Address list You store desired ID and corresponding ID name in address list.The LCD displays ID corresponding name if radio received ANI calling and nd matching ID in address list .Factory DefaultIf your radio seems to be malfunctioning, resetting the microprocessor may solve the problem. When performing the reset, you may lose memory data and stored information. Back up or write down important data before performing the reset.General SettingPress and hold1. key for over 2s to enter general setting menu.Press2. / key to choose No.29 menu, LCD displays"RESTORE".Turn selector knob to select the desired 3. operation.FACT:Resume factory default for channel,signaling and general setting.SETUP:Return initial setup for No.18-No 27 general setting menu.Press 4. key to conrm.Press and hold1. key for over 2s to enter general setting menu.Press 2. / key to choose No.28 menu, LCD displays"BOOK".Press 3. to enter into ID setting,press / to select the desired group (00-127,total is 128 group ID).Turn selector knob to select desired number,press conrm and move cursor to next edition,press to clear out all digits. After finishing edition,press 4. to confirm and enter into edition of current group's ID corresponding name.Turn selector knob to select desired letter,press to move cursor to next edition,Press to clear out all letters. 00-127,total 128 group ID and corresponding ID name.Press 5. to conrm and return into main menu.Repeat above Step 3 and Step 4 operations to edit multi-ID and corresponding ID name.Press 6. key to return into standby status.
279You can operate the transceiver by keypad or input desired frequency or channel through the QHM-03 microphone (Note:In professional transceiver mode,other keys are invalid except PTT,[ / ], and ).Keypad LockPull down the slide switch to lock position,The lamp is turned off and all of keypads is not work except PTT switch.Transmitting DTMF By Microphone KeyPAD Switches between VFO and channel mode In standby,press key to switch between channel mode and Frequency mode (VFO).Short CallingIn standby,press to transmit the selected DTMF/2TONE/5TONE in current channel.Transmitting DTMF Code:In standby,press ,LCD displays DTMF data and group.Press [ / ] key to select the desired transmitting DTMF group,then Press PTT to transmit.If no DTMF data in current group,LCD displays "EMPTY",press key again and input desired DTMF code by keypad,press PTT to transmit and store DTMF data.Squelch LevelIn standby,press 1. ,then press ,LCD displays "SQL" and current squelch level.Press 2. / to adjust the desired squelch level.(press ,then press ,turn selector knob also can adjust the desired squelch level.Press number key to conrm and exit.3. Optional signaling In standby,press ,then press to add optional signaling,repeat above operation to set DTMF,2TONE or 5TONE signaling.When first bit of Exa byte in frequency displays "D",it indicates DTMF function enable. When first bit of Exa byte in frequency displays "T",it indicates 2Tone function enable. Microphone Operation Slide DTMF key to DTMF position, press and hold the [PTT] key, transmitting the desired DTMF signaling by the numeric key directly.(Note:Slide DTMF key to DTMF position,the keyboard is invalid in standby ).Function Setup By Microphone KeypadSquelch off:In standby, press key, the squelch is disabled when icon ashed in LCD, Press again to enable squelch and the icon disappears.PTTDOWNUPLock SpeakerNumeric KeysDTMF ON/OFF
289Reverse TX/RXTX frequency turns to RX frequency & RX frequency changes to TX frequency. The signaling will also be reversed if CTCSS/DCS signaling exited in this channel.In standby,press 1. ,then press ,LCD displays “REV—OF”.Press [ 2. / ] to select the desired value.ON:Enable Frequency ReverseOFF:Disable Frequency ReversePress number keys to conrm and exit.3. In corresponding mode,press then press key to enter into scanning. In scanning mode,press / to change scan direction.Busy Channel LockoutBCLO is to disable transmitting while RX signal is received. Once the channel is busy and you press PTT, the radio will beep as warning and get back to receiving.In standby,press 1. ,then press to enter into Busy Channel Lockout.Press [ 2. / ] to select the desired value.BU: Enable BCLO, Carrier lockout, transmitting is inhibited when current channel receives a matching carrier;press [PTT] to emit error voice prompt.RL: Enable BTLO, transmitting is inhibited when current channelreceives a matching carrier but dis-matching CTCSS/DCS.press [PTT] to emit error voice prompt It can transmit in any receiving status.OFF: Busy channel lockout is disabled.Press number keys to conrm and exit.3. This function can be temporarily used in channel mode. Once the radio is turned off or switched to another channel, the temporary setting will be erased and back to initial settings. Frequency/Channel scan Scan Skip When first bit of Exa byte in frequency displays "F",it indicates 5Tone function enable.This function can be temporarily used in Channel mode . Once the radio is turned off or switched to another channel, the temporary setting will be erased and back to initial settings. This function can be temporarily used in Channel mode . Once the radio is turned off or switched to another channel, the temporary setting will be erased and back to initial settings. Microphone OperationIn Channel mode,press then press ,decimal point displayed between frequency's ten digit and unit digit,it means current channel is scan skip. Repeat above operation to set scan or scan skip in current channel.decimal point displayed between frequency's ten digit and unit 1. digit,it means current channel is scanned skip.decimal point is not displayed between frequency's ten digit and 2. unit digit,it means current channel is scanned.
299TOT (Time-out timer)The time-out timer limits the amount of transmitting time. When you reach the time limit which has been programmed by your dealer, your transmission will be cut off. In order to transmit again, you must release PTT button to reset the timer.In standby,press 1. ,then press “LCD displays "TOT-X". Press [ 2. / ] to select the desired value.Press number key to conrm and exit.3. CTCSS/DCS Encode and DecodeIn standby,press 1. ,then press to enter into CTCSS/DCS Encode and Decode.Repeat above operation to set as below:2. LCD displays T icon,it indicates CTCSS encode set in current channel.LCD displays T and SQ icon,it indicates CTCSS encode and decode set in current channel.LCD displays DCS icon,it indicates DCS encode and decode set in current channel.In corresponding icon,press [ 3. / ] to select the desired CTCSS/DCS encode and decode.Press 4. ` ,or C/SET to conrm and exit.Talk Around This function can be temporarily used in Channel mode. Once the radio is turned off or switched to another channel, the temporary setting will be erased and back to initial settings. By Talk Around function,you can directly communicate with other radios in your group in case the repeater is not activated or when you are out of the repeater range. The transceiver will transmit by RX frequency with its CTCSS/DCS signaling.In standby,press 1. ,then press key,LCD displays “TALK--OF”.Press [ 2. / ] to select the desired setting . ON:Enable Talk Around OFF:Disable Talk AroundPress number key to conrm and exit.3. This function can be temporarily used in Channel mode . Once the radio is turned off or switched to another channel, the temporary setting will be erased and back to initial settings.Voice PromptThe prompting tone provides confirmation of entry, error status or malfunctions of the transceiver. You can enable or disable this function.In standby,press 1. ,then press ,LCD displays "BEEP--XX”.Press [ 2. / ] to turn on/off BEEP voice prompt. BEEP—OF :turn off voice prompt BEEP—ON :turn on voice promptPress number key to exit and store.3. Microphone Operation
309 LCD Backlight In standby status,press 1. , then press LCD displays"LAMP-XX" .Press [ 2. / ] to select desired backlight brightness(1-32 levels).Press number keys to conrm and exit.3. Microphone Operation
3110Connect DC power cable with car battery.Connect the optional alarm cable QL-01(A) to the data jack on 1. the front panel as shown. Secure the other end of the cable to an object that stays xed in vehicle. (Note: if alarm cable QL-01 (A) is not enough long, you can choose optional alarm cable QL-01 (B) to extend).When transceiver power off by press 2. key ,the long-distance anti-theft alarm enable.Note:The long-distance anti-theft alarm only available when 3. transceiver power off .When the alarm cable QL-01(A) or QL-01(B) is removed from the 4. DATA jack or cut by improper sequence, the alarm function enable and will alarm as programmed. In alarming,the transceiver will stop alarm once receiving a matching signal. And alarm again when a matching signal disappeared.Restart radio to cancel anti-theft alarming.Reconnect with alarm 5. cable and turn off radio,the system will return to alarm mode.This function is mainly use for simple anti-theft alarm device in vehicles. When the transceiver be removed in an improper manner,the transceiver will emit and transmit alarming and background voice to system and other transceiver of the same frequency.Steering-wheel etc.Alarm cable [QL-01(B)]DC power cableBatteryAlarm cable [QL-01(A)]Long-distance Anti-theft Alarm
3211This feature will copy the programmed data and parameters in the master unit to slave units. It copies the parameters and memory program settings.Use optional CP50 cloning cable, connect the cable between the data jacks on both master and slave.1. Press and hold key, then press key to enter into cloning mode, LCD displays "2. CLONE".Press master unit's [PTT] key, LCD displays "SD XXX", "XXX" indicates data volume in transmitting. Slave unit displays "LD XXX", "XXX" indicates 3. received data volume. When the transmission is successfully finished, the master and slave unit both display "PASS". Turn off the power, disconnect the cable and repeat step 2 to step 3 operations to clone the next slave unit.Cable CloneIf the data is not successfully transmitted, turn off both units, make sure the cable connection is correct and repeat the entire operation from the beginning.GND DATA TX/RXMaster/Slave stereo plug,3.5mm plug
5883312 DCS encode and decode -VFO frequency DCS code 023NMemory channel 0-199 - Output power HIOffset direction - Key-lock setting OFFOffset frequency 600KHz TOT OFFChannel step 12.5KHz APO OFFCTCSS encode and decode - Squelch Level 4CTCSS frequency 88.5HzDefault Setting after Resetting(VHF) Trouble ShootingProblem Possible Causes and Potential Solutions(a) Power is on, nothing appears on Display.+ and - polarities of power connection are reversed. Connect red lead to plus terminal and black lead to minus terminal of DC power supply.(b) Fuse is blown. Check and solve problem resulting in blown fuse and replace fuse with new fuse.(c) Display is too dim. Dimmer setting is "LAMP-L". Please make the dimmer setting "LAMP-H".(d) No sound comes from speaker. • Squelch is muted. Decrease squelch level.• Tone or CTCSS/DCS squelch is active. Turn CTCSS or DCS squelch off.(e) Key and Dial do not function. Key-lock function is activated. Cancel Key-lock function.(i) Rotating Dial will not change memory channel. Transceiver is in CALL mode. Press the VFO or memory mode.(g) PTT key is pressed but transmission does not occur.• Microphone connection is poor. Connect microphone properly. • Antenna connection is poor. Connect antenna properly.Maintenance220-260MHz
1334Specications are subject to change without notice due to advancements in technology.GeneralFrequency Range VHF: (220~260MHz) Number of Channels200 channels Channel Spacing12.5KPhase-locked Step5KHz, 6.25KHz, 8.33KHz, 10KHz, 12.5KHz, Operating Voltage 13.8V DC ±15%SquelchCarrier/CTCSS/DCS/5Tone/2Tone/DTMFFrequency Stability ±2.5ppmOperating Temperature-20℃~+60℃Dimensions(WxHxD) 145 (W) x 47 (H) x 190 (L)mmWeight about 1.2KgReceiverSensitivity(12dB Sinad) ≤0.35μVAdjacent ChannelSelectivity ≥60dBIntermodulation ≥60dBSpurious Rejection ≥70dBAudio Response +1~-3dB(0.3~2.55KHz)Hum & Noise ≥40dBAudio distortion ≤5% Audio power output ＞2W@10%Transmitter Power Output 50WModulation 11KΦF3EAdjacent Channel Power ≥60dBHum & Noise ≥36dBSpurious Emission ≥60dBAudio Response +1~-3dB(0.3~2.55KHz)Audio Distortion ≤5%Specifications
1467.0 79.7 94.8 110.9 131.8 156.7 171.3 186.2 203.5 229.169.3 82.5 97.4 114.8 136.5 159.8 173.8 189.9 206.5 233.671.9 85.4 100.0 118.8 141.3 162.2 177.3 192.8 210.7 241.874.4 88.5 103.5 123.0 146.2 165.5 179.9 196.6 218.1 250.377.0 91.5 107.2 127.3 151.4 167.9 183.5 199.5 225.7 254.1Attached Chart50 groups CTCSS Tone Frequency(Hz) 1024 groups DCS Code.000 001 002 003 004 005 006 007010 011 012 013 014 015 016 017020 021 022 023 024 025 026 027030 031 032 033 034 035 036 037040 041 042 043 044 045 046 047050 051 052 053 054 055 056 057060 061 062 063 064 065 066 067070 071 072 073 074 075 076 077100 101 102 103 104 105 106 107110 111 112 113 114 115 116 117120 121 122 123 124 125 126 127130 131 132 133 134 135 136 137140 141 142 143 144 145 146 147150 151 152 153 154 155 156 157160 161 162 163 164 165 166 167170 171 172 173 174 175 176 177200 201 202 203 204 205 206 207210 211 212 213 214 215 216 217220 221 222 223 224 225 226 227230 231 232 233 234 235 236 237240 241 242 243 244 245 246 247250 251 252 253 254 255 256 257260 261 262 263 264 265 266 267270 271 272 273 274 275 276 277300 301 302 303 304 305 306 307310 311 312 313 314 315 316 31735
3615 Attached Chart320 321 322 323 324 325 326 327330 331 332 333 334 335 336 337340 341 342 343 344 345 346 347350 351 352 353 354 355 356 357360 361 362 363 364 365 366 367370 371 372 373 374 375 376 377400 401 402 403 404 405 406 407410 411 412 413 414 415 416 417420 421 422 423 424 425 426 427430 431 432 433 434 435 436 437440 441 442 443 444 445 446 447450 451 452 453 454 455 456 457460 461 462 463 464 465 466 467470 471 472 473 474 475 476 477500 501 502 503 504 505 506 507510 511 512 513 514 515 516 517520 521 522 523 524 525 526 527530 531 532 533 534 535 536 537540 541 542 543 544 545 546 547550 551 552 553 554 555 556 557560 561 562 563 564 565 566 567570 571 572 573 574 575 576 577600 601 602 603 604 605 606 607610 611 612 613 614 615 616 617620 621 622 623 624 625 626 627630 631 632 633 634 635 636 637640 641 642 643 644 645 646 347650 651 652 653 654 655 656 657660 661 662 663 664 665 666 667670 671 672 673 674 675 676 677700 701 702 703 704 705 706 707710 711 712 713 714 715 716 717720 721 722 723 724 725 726 727730 731 732 733 734 735 736 737740 741 742 743 744 745 746 747750 751 752 753 754 755 756 757760 761 762 763 764 765 766 767770 771 772 773 774 775 776 777N is positive code, I is negative code, total: 232groups.
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Navigation menu