Qixiang Electron Science and Technology 588V2 Land Mobile Radio User Manual

Qixiang Electron Science& Technology Co., Ltd Land Mobile Radio

user manual

588
Land Mobile Radio
FCC ID:T4K588V2
Do not attempt to configure your transceiver while driving,it is
dangerous.
This transceiver is designed for a 13.8V DC power supply. Don't use
a 24V battery to power on the transceiver.
Do not place the transceiver in excessively dusty, humid or wet
areas, nor unstable surfaces.
Please keep it away from interferential
devices (such as TV, generator etc.)
Do not expose the transceiver to long
periods of direct sunlight nor place it close
to heating appliances.
If an abnormal odor or smoke is detected
coming from the transceiver, turn OFF the
power immediately. Contact an Anytone
service station or your dealer.
Do not transmit with high output power for extended periods; the
transceiver may overheat.
Please observe the following precautions to prevent fire, personal
injury, or transceiver damage:
Precautions
Power
CONTENTS
New and Innovative Features ..............................................1
Supplied Accessories/Optional Accessories .....................2
Supplied Accessories .......................................................................2
Optional Accessories .......................................................................2
Initial Installation ..................................................................3
Mobile Installation ............................................................................3
DC Power Cable Connection ...........................................................4
Power Supply Voltage Display .........................................................6
Antenna Connection ........................................................................6
Accessories Connections .................................................................7
Getting Acquainted ..............................................................8
Front panel .......................................................................................8
Rear panel .......................................................................................9
Display .............................................................................................9
Microphone ......................................................................................10
Working Mode(Amateur Transceiver or Professional
Transceiver)
........................................................................11
Basic Operations .................................................................12
Switching the Power On/Off ............................................................12
Adjusting the Volume ......................................................................12
Switch between VFO and Channel mode .......................................12
Adjusting Frequency/Channel Through Selector Knob ....................12
Receiving .........................................................................................12
Transmitting .....................................................................................12
Transmitting Tone-Pulse ..................................................................13
Transmitting Optional Signaling ......................................................13
Channel Edit ....................................................................................13
Channel Delete ................................................................................13
Shortcut Operations .............................................................14
Squelch Off/Squelch Off Momentary................................................14
Squelch Level Setup ........................................................................14
Frequency/Channel Scan ................................................................14
Channel Scan ..................................................................................14
CTCSS/DCS Encode and Decode Setup ........................................14
CTCSS Scan ....................................................................................15
DCS Scan ........................................................................................15
............................................................15
Compander (Decrease the background noise and enhance audio
clarity ..................................................................................................15
Offset Direction and Offset Frequency Setup ..................................16
Keypad Lockout ...............................................................................16
Current Voltage Enquiry ...................................................................16
Auto-Dialer Setup .............................................................................16
Transmitting Edited DTMF Tones in the Auto-dialer Memory ...........17
General Setting .....................................................................18
Frequency Channel Step Setup .......................................................18
DTMF, DTMF ANI, 2Tone or 5Tone Signaling ..................................18
Sending 2-Tone Call .........................................................................19
Sending 5-Tone Call .........................................................................19
Sending DTMF call ..........................................................................19
Signaling Combination Setup ...........................................................19
CONTENTS
TX OFF Setup ..................................................................................21
Busy Channel Lockout .....................................................................21
Editing Channel Name .....................................................................21
Reverse TX/RX ................................................................................21
Talk Around ......................................................................................22
Voice Compander ...........................................................................22
Radio's DTMF SELF ID ENQUIRY .................................................22
Radio's 5TONE SELF ID ENQUIRY ...............................................23
Voice Prompt ....................................................................................23
TOT (Time-out timer) .......................................................................23
APO (Auto power off) .......................................................................23
DTMF Transmitting Time ..................................................................24
Squelch Level Setup ........................................................................24
Scan Dwell Time Setup ....................................................................24
LCD Backlight ..................................................................................24
Pilot Frequency ................................................................................25
Display Mode Setup .........................................................................25
PIN Setup ........................................................................................25
Address List ....................................................................................26
Factory Default .................................................................................26
Microphone Operation .........................................................27
Function Setup By Microphone Keypad ...........................................27
Squelch Level ..................................................................................27
Optional Signaling ...........................................................................27
Scan Skip ........................................................................................28
Frequency/Channel Scan ...............................................................28
Busy Channel Lockout .....................................................................28
Reverse TX/RX ................................................................................28
TOT (Time-out timer) ........................................................................29
CTCSS/DCS Encode and Decode ...................................................29
Talk Around .....................................................................................29
Voice Prompt ....................................................................................29
LCD Backlight .................................................................................30
Long-distance Anti-theft Alarm ..........................................31
Cable Clone ..........................................................................32
Maintenance ..........................................................................33
Default Setting after Resetting(VHF) ...............................................33
Default Setting after Resetting(UHF) ...............................................33
Trouble Shooting ..............................................................................33
Specications .......................................................................34
Attached Chart ......................................................................35
50 groups CTCSS Tone Frequency(Hz) ..........................................35
1024 groups DCS Code. ..................................................................35
1
1
New and Innovative Features
588 Mobile Radio has nice housing, stoutness & stability, advanced and reliable functions, perfect & valuable. This amateur mobile radio especially
designs for drivers and it pursues company philosophy of innovation and practicality. More functions as follows:
Display on a large LCD with adjustable brightness, convenient for nighttime use.
There are Amateur operation mode and Professional
operation mode for option.
Distribute buttons reasonably, convenient for operation. Adopt superior quality material, better technology and high quality radiator to ensure
stable and durable operation.
200 programmable memorized channels, identied by editing name.
Programming different CTCSS, DCS, 2Tone, 5Tone in per channel, rejecting extra calling from other radios.
Various scan functions including CTCSS/DCS Scan function.
Using
5Tone to send Message, Emergency alarm, Call all, ANI, Remotely kill, Remotely Waken, etc.
Automatic
calling Identication function by DTMF--ANI or 5Tone--ANI .
Compander function for decrease the background noise and
enhance audio clarity, it can set compander ON/OFF per channel.
Theft alarm provides extra safety.
2
2Supplied Accessories/Optional Accessories
Supplied Accessories
Optional Accessories
After carefully unpacking the transceiver, identify the items listed in the table below. We suggest you keep the box and packaging.
Transceiver
Spare Fuses (one pair)
[QF-01]
Cloning Cable (CP50)
Desktop
Microphone
(QDM-01)
Alarm Cable A
[QL-01(A)] Alarm Cable B (Extension line)
[QL-01(B)]
Car Antenna
(QCA-01)
USB Programming
Cable (PC50) Cigar-Plug Connection
Line (QCC-01) Programming Software
(QPS-588) Regulated Power
Supply (QRP-01)
External Speaker
(SP-01)
User Manual
Microphone (QHM-03)
(with DTMF keyboard) Mobile Mounting
Bracket (QMB-01) DC Power Cable with
Fuse Holder(QPL-01) Hardware Kit for Bracket
Black screws
(M4X8mm)
4PCS(QSS-01A)
Tapping screws
(M5X8mm)
4PCS(QSS-01B)
S-Washer
(QSS-01D)
3
To install the transceiver, select a safe, convenient location inside your
vehicle that minimizes danger to your passengers and yourself while the
vehicle is in motion. Consider installing the unit at an appropriate position
so that knees or legs will not strike it during sudden braking of your
vehicle. Try to pick a well ventilated location that is shielded from direct
sunlight.
Install the mounting bracket in the vehicle using the supplied self-
1.
tapping screws (4pcs) and at washers (4pcs).
Position the transceiver, then insert and tighten the supplied
2.
hexagon SEMS screws.
Double check that all screws are tightened to prevent vehicle
vibration from loosening the bracket or transceiver.
3
Car body
Washer (M5)
Tapping screw
(M5x20mm)
Mounting bracket
Initial Installation
Mobile installation Determine the appropriate angle of the transceiver, using the 3 screw
hole positions on the side of the mounting bracket.
4
Connect the DC power cable to the transceiver's power supply
6.
connector.
Press
the connectors rmly together until the locking tab clicks.
If the ignition-key on/off feature is desired(optional feature),use the
3
Red
Black
Ext. Power jack
DC power cable
Initial Installation
DC Power Cable Connection
Mobile Operation
In many cars,the cigar-lighter plug is always powered. If this is the case, you
cannot use it for the ignition key on/off function.
The vehicle battery must have a nominal rating of 12V. Never
connect the transceiver to a 24V battery. Be sure to use a 12V
vehicle battery that has sufficient current capacity. If the current
to the transceiver is insufficient, the display may darken during
transmission, or transmitting output power may drop excessively.
When the ignition key is turned to ACC or ON(Start) position with
7.
the radio turned off, the power switch illuminates. The illumination
will be turned off when the ignition key is turned to the off position.
Route the DC power cable supplied with the transceiver directly
1.
to the vehicle's battery terminals using the shortest path from the
transceiver.
We recommend you do not use the cigarette lighter socket as
some
cigarette lighter sockets introduce an unacceptable voltage drop.
The entire length of the cable must be dressed so it is isolated from
heat, moisture, and the engine secondary (high voltage) ignition
system/ cables.
After installing cable, in order to avoid the risk of damp, please
2.
use heat-resistant tap to tie together with fuse box. Don't forget to
reinforce whole cable.
In order to avoid the risk of short circuit, please cut down
3.
connection with negative (-) of battery, then connect with radio.
Confirm the correct polarity of the connections, then attach the
4.
power cable to the battery terminals; red connects to the positive (+)
terminal and black connects to the negative (-) terminal.
Use the full length of the cable without cutting off excess even if
the
cable is longer than required. In particular, never remove the fuse
holders from the cable.
Reconnect any wiring removed from the negative terminal.
5.
optional QCC-01(For Cigar-Plug connection) cable. Connect one of
the cables between the ACC terminal or a Cigar-Plug that operates
with the vehicle ignition or ACC switch on the vehicle and EXT
POWER jack on the rear side of the unit.
Locate the power input connector as close to the transceiver as possible.
5
3
Red
Black
Regulated power supply (QRP-01)
DC power cable with fuse holder (QPL-01)
Regulated
power supply
(QRP-01)
Ext. Power jack
ACC terminal
Cigar-Plug connection
Initial Installation
Before connecting the DC power to the transceiver, be sure to switch
the transceiver and the DC power supply OFF.
Do not plug the DC power supply into an AC outlet until you make all
connections.
In order to use this transceiver for xed station operation, you will
need a separate 13.8V DC power supply (not included) , power
supply( QRP-01) as optional accessories. Please contact local dealer
to require.
The recommended current capacity of your power supply is 12A.
Connect the DC power cable to the regulated DC power supply
1.
and ensure that the polarities are correct. (Red: positive, Black:
negative).
Do not directly connect the transceiver to an AC outlet.
Use the supplied DC power cable to connect the transceiver to a
regulated power supply.
Do not substitute a cable with smaller gauge wires.
To turn on the unit, press the power switch manually while it is
illuminated. (While ignition key is at ACC or ON position)
When the ignition key is turned to ACC or ON position with the
8.
radio's power switch on, the unit turns on automatically and the
power switch will be lit. Turn the ignition key to OFF position or
manually turn the power switch off to shut down the radio.
Using extra cable,power consumption:5MAH.
9.
Without this function,user can turn on/off radio by Power knob.
10.
Connect the transceiver's DC power connector to the connector
2. on
the DC power cable.
Press the connectors rmly together until the locking tab clicks
.
Fixed Station Operation
6
3Initial Installation
REPLACING FUSES
If the fuse blows, determine the cause, then correct the problem.
After the problem is resolved, replace the fuse. If newly installed fuses
continue to blow, disconnect the power cable and contact your autho-
rized dealer or an authorized servi-
cecenter for assistance.
Only use fuses of the specified type and rating, otherwise the
transceiver could be damaged.
After connecting the transceiver to the power supply, the supply voltage
can be displayed on LCD by pressing the FUN key together with the
key.
The display immediately changes as the voltage supply changes, It
also displays voltage during transmission.
The transceiver will return to its normal operation when the power is
switched ON or repeat above operation.
Before operating, install an efcient, well-tuned antenna. The success
of your installation will depend largely on the type of antenna and its
correct installation. The transceiver can give excellent results if the
antenna system and its installation are given careful attention.
Use a 50Ω impedance antenna and low-loss coaxial feed-line that
has a characteristic impedance of 50 Ω, to match the transceiver input
impedance. Coupling the antenna to the transceiver via feed-lines having
an impedance other than 50Ω reduces the efficiency of the antenna
system and can cause interference to nearby broadcast television
receivers, radio receivers, and other electronic equipment.
Fuse Location Fuse Current Rating
Transceiver 15A
Supplied Accessory DC
power cable 20A
If you use the transceiver for a long period when the vehicle battery is
not fully charged, or when the engine is OFF, the battery may become
discharged, and will not have sufcient reserves to start the vehicle. Avoid
using the transceiver in these conditions.
The range of displayed voltage is only from 7V to16V DC, because the
displayed value is estimated, please use a voltmeter when a more precise
reading is desired.
Power supply voltage Display
Antenna Connection
Important
Transmitting without first connecting an antenna or other matched
load may damage the transceiver. Always connect the antenna to the
transceiver before transmitting.
All xed stations should be equipped with a lightning arrester to reduce
the risk of re, electric shock, and transceiver damage.
The possible locations of antenna on a car are shown as following:
7
3
SP-01
SP-01 Ground
Microphone
connector
Microphone [QHM-03] Antenna
[QCA-01]
External speaker [SP-01]
Error
Initial Installation
External Speaker
Microphone
If you plan to use an external speaker, choose a speaker with an
impedance of 8 Ω. The external speaker jack accepts a 3.5 mm (1/8")
mono (2-conductor) plug.
For voice communications, connect a microphone equipped with
an 8-pin modular plug into the modular socket on the front of the
main unit. Press rmly on the plug until the locking tab clicks. Attach
the supplied microphone hanger in an appropriate location using the
screws included in the screw set.
External speaker adopt double port BTL, please care about the connecting
way. The speaker can not connect with the ground, otherwise the speaker
will be fault. The wrong connecting way as the following picture.
Accessories Connections
MHz/SHIFT Switches Narrow band
Switches power
8
4
NO. KEY FUNCTION
1Pow(Power) Power on/Off
2VOL Adjust Volume Key
3Main Dial Change frequency, memory channel and scan
direction etc.
4FUN/SET Function Key
5V/M/MW Switches between VFO mode and Channel
mode
6MHz/SHIFT Step Size Key ( step:1MHz)
7TS/DCS/LOCK Sets CTCSS and DCS value
8CAL/H/L Call key
9SQL/D Squelch off
10 Data Terminal Data reading/writing, cloning and theft alarm
functions
11 TX lights during Transmitting
12 Mic.connector Microphone connection port
NO. KEY FUNCTION
4FUN/SET Conrms the selective functions and exit
5V/M/MW Stores data into channels
6MHz/SHIFT Sets offset direction and offset frequency
7TS/DCS/LOCK Sets Keypad lock function
8CAL
transmission
9SQL/D Compander mode on/off
NO. KEY FUNCTION
1PWR Reset to factory default settings
5V/M/MW Erase the memory
6
7TS/DCS/LOCK Auto dialer
8CAL/H/L
Enters clone data function mode
9SQL/D Enters power supply voltage indication mode
NO. KEY FUNCTION
4FUN/SET Press and hold for 2s to enter the Setting
mode
9SQL/D Monitor mode
Getting Acquainted
Front panel Press key until icon appears then press the following
key.
Press key and following key together to activate
following function:
Functions that require continuous pressing following key
to be activated
Basic Functions
9
4
21
NO. KEY FUNCTION
1Ext. Power
Jack
Terminal for connecting optional cable QCC01 for
use with ignition key On/Off function.
The radio will auto power on when car is driving.
The radio will auto power off when car stops.
2Ext.Speaker
Terminal Terminal for optional external speaker SP01
3Antenna
Connector Connection for 50Ω coaxial cable and antenna.
NO. KEY
Å
FUNCTION
1 SQL Squelch level.
2 MIn channel mode.
3 Indicates the channel number in channel mode.
4Decimal point
Channel skip.
5Decimal point Indicates the decimal point of frequency and the
scanning function.
6 Indicates the frequency or memory name.
7Signal is being received or monitor.
8Signal strength of receiving and transmitting.
9Compander.
10 Keypad lock .
11 DCS Set DCS function.
12 Set CTCSS function.
13 + _Offset frequency direction.
14 Scramble.
15 A Auto power off.
16 Nar Narrow band.
17 Pressing key.
3
Getting Acquainted
DISPLAY
Rear panel
3
1
2
13 10
11
12
14
4567
8
9
15
16
17
18
19 13
10
4
NO. KEY FUNCTION
1UP Increase frequency ,channel number or setting value.
2DOWN Decrease frequency, channel number or setting value.
3PTT Press the PTT (Push-TO-Talk) key to transmit.
4Number Key Input VFO frequency or DTMF dial out etc..
5DTMF ON/
OFF Switches between DTMF dialing or function operating.
6LOCK Switch Locks out the UP 、Down、Numerical keys and Function
keys.
7MIC Speak here during transmission.
Key Pad Serial Data
+5V
DOWN
UP
MIC GND
MIC
PTT
GND
microphone MIC Connector Diagram(in the front view of connector)
Getting Acquainted
11
5
According to practical application,you can set the radio works as
Amateur Transceiver mode or Professional Transceiver mode . There
are also 2 levels operation menu to set functions as you need. It is easy
and convenient (From No.1 to No. 15 are channel function setup,From
No.15 to No.29 are general setting setup).

1.
 In PC software's "General
Setting"menu ,choose "Display Mode" to select Amateur
Transceiver mode or Professional Transceiver mode.
 :Please refer to "Display Mode" in Page 24.

2. Except setting as "CH" mode, others
considered as Amateur transceiver mode. Under this mode,press
key to switch between Channel mode and VFO mode .
Professional Transceiver Mode
3. When
set display mode as "CH",it enters
into Professional Transceiver mode.At
this mode,except scan,other shortcut
operation can't operate.And from No.1-
17 menu in function setting will be
auto-hidden,They should be set by
PC software.If there is corresponding
name for current channel,the LCD
will display current channel name
Otherwise,it shows current channel number. (As pic 4) (As pic 5)
Under every mode, from No. 18-29 menu in
4. general setting can be
changed and saved.
VFO Mode(Frequency mode)C. :
This mode shows only frequency
on the display. Shortcut operation
and Channel setting will be
changed & stored as the latest
value permanently.Once the radio is
turned off or changed to new VFO frequency, the latest setting is
remained until next change.(As pic 3)
If transceiver programmed as professional transceiver mode and
locked,you can't return to amateur transceiver mode by manual
operation from general setting.
(Pic 2)
(Pic 4)
(Pic 5)
Frequency + Channel modeA. : When set display as"FR",it enters
into Frequency+Channel mode, new
setting of channel operation and
shortcut operation can be temporarily
used by user. Once the radio is
turned off or switched to another
channel, the temporary setting will be
erased and back to initial settings.(As pic 1)
Channel+Name Tag ModeB. : When set display as "NM",it enters
into Channel +Name Tag mode. At this mode, it will display
corresponding channel name when
the current channel is edited with
name. Otherwise, it will display
frequency + channel. Its operations
are the same as frequency + channel
mode.(As pic 2)
(Pic 3)
WORKING MODE (AMATEUR TRANSCEIVER OR PROFESSIONAL TRANSCEIVER)
12
In standby, press key or Microphone's
key until appear , this indicates current
channel in channel mode. Repeat above
6
PWR KEY
Dial
Frequency
decrease Frequency
increase
Volume Knob
Min
Volume Max
Volume
Basic Operations
Switching The Power On/Off
Adjusting The Volume
Switch between VFO and Channel mode
Adjusting Frequency/Channel THROUGH SELECTOR KNOB
Receiving
according to the option selected during
installation Press the switch or turn the
ignition key to ACC (speed up) or ON (startup)
position to power on radio . Press the key
for 1s or turn the ignition key to OFF position
to turn off.
When the channel you are operating is
called, the screen shows and field
intensity, in this way, you can hear the calling
from transmitting party.
Under frequency (VFO) mode, you can
1.
change the current frequency to the
desired one through selector knob; Turn
clockwise to increase frequency; turn
counterclockwise to decrease. Every
gear will increase or decrease one step.
Press key, the decimal point of
Turn the VOL knob clockwise to increase
the audio level, counterclockwise to decrease.
During communication, volume can be adjusted more accurate.
If the transceiver has set at higher squelch level, it may fail to hear the calling.
operation to switch between Frequency mode
(VFO) and Channel mode.
frequency in screen will be auto-hidden. In this status, turn selector
knob or Microphone [ / ] key will increase or decrease
frequency quickly by 1MHz step .
Under channel mode, you can change the current channel to the
2.
desired one through selector knob, clockwise turn to the forward
channel, anticlockwise turn to the backward channel. In relative
working mode, Microphone's [ / ] key has same
function for adjusting frequency and channel.
Transmitting
Press and hold key or press MIC's key to monitor for a while
to conrm the channel desired is not busy. Release or press Mic's
key to return standby status,Then press and hold [PTT] key to speak
into microphone.
When the channel you are operating is called,the screen shows BUSY
and field intensity,you can't hear the calling from transmitting party,it
means current channel receives a matching carrier but unmatching
signaling(Refer to CTCSS/DCS encode and decode or Optional Signaling
setup).
13
Basic Operations
Transmitting Tone-Pulse
Transmitting OPTIONAL SIGNALING
Press and hold [PTT] key, then press Microphone [ ] key to
transmit current selected tone-pulse signal.
Press and hold [PTT] key, then press Microphone key or press
key in front panel or press Mic's key to transmit pre-stored and
selected DTMF/2Tone/5Tone optional signaling.
Channel Edit
Channel Delete
Under frequency mode (VFO), turn
1.
selector knob to select the desired
frequency or input frequency by MIC's
numeric keys.
Press
2. key to enter CTCSS/DCS
signaling setup, turn selector knob to
select the desired signaling.
Press
3. key, LCD appears ,
icon and current channel number,
icon ashing means current channel is
Under channel mode, turn selector knob to select channel which
1.
you want to delete.
Press
2. key and key together, current channel will be
deleted and emitted a prompt voice. icon ashing means current
channel is deleted.
empty.
Turn selector knob to select the desired channel number to store.
4.
Press
5. key, , icon and channel number disappears
and emit a prompt voice, thus the channel storage succeed.
6
Press and hold [PTT] key, LED lights RED and power intensity showed in
screen indicates it is transmitting, release to receive.
Please hold the microphone approximately 2.5-5.0cm from your lips
,
and then speak into the microphone in your normal speaking voice to
get best timbre.
14
7Shortcut Operations
Squelch level Setup
Frequency/Channel Scan
Channel Scan
CTCSS/DCS Encode and Decode setup
Setting the radio to a tight squelch level,you can avoid unwanted
signals or noise,but you may not receive a weak signal. Therefore,it will
be better for you to select the normal squelch level.
In frequency (VFO) mode, this function is designed to monitor signal
of every communicative frequency point of transceiver "step size" you
have set.
In channel mode, this function is designed to monitor signal in every
channel.
In channel mode,Press
1. key for 1s to enter into channel scan
Repeatedly press key to check whether
set CTCSS/DCS encode and decode in current
channel or not.
When LCD appears
1. iron, it means
current channel with CTCSS encode,
turn selector knob or press Microphone's
[ / ] key to select desired
CTCSS encode.
When LCD appears
2. and iron, it
means current channel with CTCSS
encode and decode, turn selector knob
or press Microphone's [ / ]
to select desired CTCSS code.
While standby, press
1. key and turn
selector knob until LCD appears
and current squelch level
Turn selector knob or press MIC [
2.
/ ] key to set desired squelch level.
Press any key except
3. and
key to exit .
Frequency Scan
In VFO mode,press
1. for 1s to enter
into frequency scan.
Turn selector knob or press Microphone [
2. / ] key to
change scan direction.
Press any key except
3. and key to exit.
Turn selector knob or press Microphone
2.
[ / ] key to change scan
direction.
Press any key except
3. and key
to exit.
squelch off/squelch off momeNTARY
key programmed as Squelch Off or Squelch Off Momentary to
monitor the weak signal.
Squelch Off: Press
1. key to disable squelch ,press key
again to resume squelch.
Squelch Off Momentary: Press and hold
2. key to disable
squelch,release key to resume squelch.
The above functions should be set in programme software.
15
7
Shortcut Operations
CTCSS SCAN
Repeatedly press key until LCD
displays and icons ,then hold
key for 1S to enter into CTCSS scanning.
Once nding a matching CTCSS signaling ,it
will stop for 15s then scan again.
Under channel mode,this operation can be temporarily used by user. Once
the radio is turned off or switched to another channel,the temporary setting
will be erased.
When LCD appears
3. iron, it means current channe can be set
with DCS encode and decode together, turn selector knob or press
Microphone's [ / ] to select desired DCS encode and
decode.
CTCSS:62.5-254.1, Total 51groups; DCS:000N-777I total 1024
4.
groups. N is positive code, I is inverse code.
Press any key except
5. , and keys to return into
standby status.
Repeatedly press key until LCD
displays DCS icons ,then hold key for
1S to enter into DCS scanning. Once nding
a matching DCS signaling ,it will stop for 15s
then scan again.
compander function.
Compander function will decrease the background noise and enhance
audio clarity, especially in long range communication.
Press
1. key, then press key to
turn on compander function, repeat
above operation again to turn off
Compander (Decrease the background noise and ENHANCE
AUDIO CLARITY)
When LCD appears
2. iron, enable
compander in current channel.
When LCD doesn't display
3. iron,
disable compander in current channel.
DCS SCAN
16
Press key until LCD displays
1.
icon, then press key until, LCD
displays icon, it indicates keypad
lockout function is valid.
This will automatically transmit pre-programmed and stored DTMF
tones. And they are often used to remote control electronic devices or
AUTOPATCH phone systems available on some repeater.
Press and hold
1. key, then press key to enter the
auto-dialer enquiry mode, LCD displays current default data and
current group displayed on left. If no data in current group,it
shows"EMPTY".
Press and hold key, then press
1.
key, LCD displays current battery
voltage.
Repeat above operation to return into
2.
VFO or Channel mode
frequency.
When LCD displays " " icon, it indicates negative offset, which
4.
means transmitting frequency lower than receiving frequency.
Turn selector knob or Mic's [
5. / ] key to change offset
frequency, offset frequency changed as per stepping.
Press any key except
6. and key to exit into standby.
Press
1. key until the icon displays
on the LCD, then press key, LCD
displays offset direction and offset
frequency.
Repeatedly press key to select
2.
positive offset and negative offset.
When LCD displays " " icon, it indicates
3.
positive offset, which means transmitting
frequency higher than receiving
7
Repeater receives a signal(UP-LINK) on one frequency and re-
transmits on another frequency(DOWN-LINK). The difference between
these two frequencies is called the offset frequency. If the UP-LINK
frequency higher than DOWN-LINK frequency, the direction is positive, If
it is lower, the shift direction is negative.
Avoiding unintentional operation, this function will lock main keys, all
keys except 、 and key are invalid.
Offset Direction and offset frequency setup KEYPAD LOCKOUT
Current Voltage ENQUIRY
Auto-Dialer Setup
Shortcut Operations
In voltage display mode, all functions and channel or frequency
selection are invalid.
This function will display Current Battery Voltage.
Repeat above operation,
2. icon disappears, it indicates keypad
lockout function is invalid.
Under channel mode,this operation can be temporarily used by
user.
Once the radio is turned off or switched to another channel,the
temporary setting will be erased.
17
Turn selector knob to choose group you
2.
desired. Total:16 group,01-16.
7
Shortcut Operations
Press
3. key to enter into editing of
current group,press MIC's numeric
keys to set your desired data.
The display scrolls when the 7th digit
4.
is entered. The numbers 0-9, --, A-D, *
and # can be stored up to a total of 23
digits.
After editing,press PTT or
5. key to send current group and store
edited DTMF signaling. Press to exit and store.
Press
1. key, then press key to
enter into auto-dialer enquiry
Turn selector knob to select desired
2.
transmitting group
Press PTT or
3. key to transmit
current selected DTMF tones.
Transmitting Edited DTMF tones in the Auto-dialer memory
18
Press
2. / key to choose No.01 menu, LCD displays ”STP--
125”
Turn selector knob to select the desired frequency channel step.
3.
Channel step: 5K,6.25K,8.33K,10K,12.5K,20K,25K,30K and 50K,
total 9 kinds.
Press
4. key to conrm and exit
Press and hold
1. key for over 2s to
enter general setting menu.
Press and hold
1. key for over 2s to enter general setting menu.
Press
2. or to select the desired function option.
Turn selector knob to select the desired setup.
3.
Press
4. to conrm and exit.
Meanwhile,if you want to edit channel name or start up menu,press
or to move forward or backward,Press to store and
exit.
Only in frequency (VFO) mode, this function is valid. Turn selector
knob to select frequency or frequency scanning which is restricted by
frequency step size.
8General Setting
Frequency Channel Step Setup
This function is auto-hidden in channel mode.
DTMF, DTMF ANI, 2Tone or 5Tone Signaling
DTMF/5Tone/2Tone signalling function as similarily as CTCSS/DCS.
Without receiving correspondent tone signalling, the speaker will remain
mute. DTMF and 5Tone signalling can be applied for other advanced
features such as ANI, PTT ID, group call, remotely stun,remotely kill,
waken,...etc. The signalling edition must be done through programming
software. Please refer to the HELP option in the programming software
to know how to operate these features.
Press and hold
1. key for over 2s to
enter into general setting menu.
Press
2. / to choose No 2
menu,LCD displays"T-OFF" .
Turn selector knob to
3. select the desired setup.
"DTMF”: the channel will be mute by a DTMF signal. The
speaker won’t be open until receiving a correspondent DTMF
signal. Hold "PTT" then press [UP] or press directly to
transmit the pre-stored DTMF signaling.
In Profession transceiver mode,the functions from No.1 to No.17
will be auto-hidden.
In DTMF signaling mode,press for 2s until LCD displays
"AN---",turn selector knob to select desired digit(the other party
ID).In this mode,press to confirm exist digit and move
cursor to next,press to forward cursor.After editing,press
key to operate ANI call.
"2TONE": the channel will be mute
by a 2-Tone signal. The speaker
won’t be open until receiving a
correspondent 2-Tone signal.Hold
“PTT” then press [UP] or press
directly to transmit the pre-stored
2-Tone signaling.
"5Tone": the channel will be mute
by a 5-Tone signal. The Speaker won’t be open until receiving
a correspondent 5-Tone signal. hold “PTT” then press [UP] or
19
8
Sending 5-Tone Call
Press
2. / key to choose
No.04 menu, LCD displays "5TON
XX","XX"indicates the group in the list.
Turn selector knob to select the desired
3.
sending 5TONE group,Press PTT to
transmit selected group.
Total:100groups,00-99,Default:00.
4.
Press
5. key to conrm and exit.
General Setting
Content and name of 5TONE will be edited by programming
software.This radio only query edited group or name.If there is
corresponding name for 5TONE,this operation will display 5TONE
corresponding name.
Press directly to transmit the pre-stored 5-Tone signaling.
In 5Tone signaling mode,press for 2s until LCD displays
"AN---",turn selector knob to select desired digit(caller ID).In
this mode,press to conrm exist digit and move cursor to
next,press to forward cursor.After editing,press key to
operate ANI call.
Press
4. key to conrm and exit
Sending 2-Tone Call
Press and hold
1. key for over 2s to enter general setting menu.
Press
2. / key to choose
No.03 menu, LCD displays "2TON
XX","XX"indicates the group in the list.
Turn selector knob to select the desired
3.
sending 2TONE group,Press PTT to
transmit selected group.
Total:32groups,00-31,Default:00.
4.
Press
5. key to conrm and exit.
Content and name of 2TONE will be edited by programming
software.
This radio only query edited group or name.If there is
corresponding name for 2TONE,this operation will display 2TONE
corresponding name.
Press and hold
1. key for over 2s to enter general setting menu
Sending DTMF call
Press and hold
1. key for over 2s to enter general setting menu.
Press
2. / key to choose
No.05 menu, LCD displays "DTMF
XX","XX"indicates the group in the list.
Turn selector knob to select the desired
3.
sending DTMF group,Press PTT to
transmit selected group.
Total:16groups,00-16,Default:00.
4.
Press
5. key to conrm and exit.
Signaling Combination setup
This function is to improve the level of protecting the radio against
receiving irrelative signal.
20
8
Turn selector knob to select the desired
3.
combination
If select "SQ",it indicates you can hear the calling from caller when
receive a matching carrier.
If LCD displays "CTC",it indicates
you can hear the calling from caller
when receive a matching carrier and
CTCSS/DCS signaling .
If LCD displays "TON",it indicates
you can hear the calling from caller
when receive a matching carrier and
DTMF/2TONE/5TONE signaling .
If LCD displays "C/T",it indicates
you can hear the calling from
caller when receive a matching
carrier and CTCSS/DCS and
DTMF/2TONE/5TONE signaling .
If LCD displays "C/T",it indicates you can hear the calling from
caller when receive a matching carrier and either CTCSS/DCS
DTMF/2TONE/5TONE signaling. .
Press
4. key to conrm and exit
General Setting
Press and hold
1. key for over 2s to
enter general setting menu.
Press
2. / key to choose No.06
menu, LCD displays "SPK--SQ".
This setting will be set together with adding optional signaling
and CTCSS/DCS.
21
8
TX OFF SETUP
Disable this function,it is invalid to press PTT,current channel only
works in RX mode.
Press and hold
1. key for over 2s to enter general setting menu.
Press
2. / key to choose No.09 menu, LCD displays"TX-
ON".
Turn selector knob to select the desired
3.
setting .
On:In current channel,Press PTT to
transmit
OFF:In current channel,Press PTT is
invalid.
Press
4. key to conrm and exit.Default:ON.
Busy Channel Lockout
BCLO is to disable transmitting while RX signal is received. Once the
channel is busy and you press PTT, the radio will beep as warning and
get back to receiving.
Press and hold
1. key for over 2s to
enter general setting menu
Press
2. / key to choose No.10
menu, LCD displays"LOCK--OFF".
Turn selector knob to select the desired
3.
setting.
BU: Enable
BCLO, Carrier lockout, transmitting is inhibited when
current channel receives a matching carrier;press [PTT] to emit
error voice prompt and back to receiving status.
RL: Enable
BTLO, transmitting is inhibited when current channel
receives a matching carrier but dis-matching CTCSS/DCS.press
[PTT] to emit error voice prompt and back to receiving status.
OFF:
Busy channel lockout is disabled.It can transmit in any
receiving status.
Press
4. key to conrm and exit.
Press and hold
1. key for over 2s to
enter general setting menu.
Press
2. / key to choose No.11
menu, LCD displays cursor and ashing.
Turn selector knob to select the desired letter,press
3. key to
conrm selected letter and enter into next edition,Press to
return forward edition.
After edition,press
4. key to exit.
Reverse TX/RX
General Setting
Editing Channel NAME
In Frequency (VFO) mode ,this function will be auto-hidden.
TX frequency turns to RX frequency & RX frequency changes to TX
frequency. The signaling will also be reversed if CTCSS/DCS signaling
exited in this channel.
Press and hold
1. key for over 2s to enter general setting menu
22
8
Press
2. / key to choose No.12
menu, LCD displays "REV—OF".
Turn selector knob to select the desired
3.
setting.
ON:Enable Frequency Reverse
OFF:Disable Frequency Reverse.
After edition,press
4. key to exit.
Talk Around
Press
2. / key to choose No.14
menu, LCD displays”COMP--OFF”.
Turn selector knob to select the desired
3.
setting.
ON:Enable compander
OFF:Disable compander
Press
4. key to conrm and exit.Default:OFF
General Setting
By Talk Around function,you can directly communicate with other radios
in your group in case the repeater is not activated or when you are out of
the repeater range. The transceiver will transmit by RX frequency with its
CTCSS/DCS signaling.
Press and hold
1. key for over 2s to
enter general setting menu.
Press
2. / key to choose No.13
menu, LCD displays "TALK—OF".
Turn selector knob to select the desired
3.
setting.
ON:Enable Talk Around
OFF:Disable Talk Around
After edition,press
4. key to exit.
Voice Compander
Enable this function to reduce background noise and enhance audio
clarity, especially in long range communication.
Press and hold
1. key for over 2s to enter general setting menu
Radio's DTMF SELF ID ENQUIRY
Press and hold
1. key for over 2s to
enter general setting menu.
Press
2. / key to choose No.16
menu, LCD displays”D--XXX” XXX is radio's DTMF SELF ID.
Press
3. key to conrm and exit.
23
8
Radio's 5TONE SELF ID ENQUIRY
Press and hold
1. key for over 2s to
enter general setting menu.
Press
2. / key to choose No.17
menu, LCD displays"F--XXXXX",
"XXXXX" is radio's 5TONE SELF ID.
Press
3. key to conrm and exit.
Voice Prompt
The prompting tone provides confirmation of entry, error status or
malfunctions of the transceiver. You can enable or disable this function.
Press and hold
1. key for over 2s to
enter general setting menu.
Press
2. / key to choose No.18
menu, LCD displays"BEEP--ON".
Turn selector knob to select the desired
3.
setting.
ON:Enable voice prompt
OFF:Disable voice prompt
Press
4. key to conrm and exit.Default:ON.
TOT (Time-out timer)
The time-out timer limits the amount of transmitting time. When you
reach the time limit which has been programmed by your dealer, your
transmission will be cut off. In order to transmit again, you must release
PTT button to reset the timer.
Press and hold
1. key for over 2s to enter general setting menu.
Press
2. / key to choose No.19
menu, LCD displays"TOT--3"
Turn selector knob to select the desired
3.
setting.
Timer:1-30min,each level 1min
OFF:Disable TOT
Press
4. key to conrm and exit.Default:3.
APO (Auto power off)
Once APO is activated, the radio will be automatically switched off
when the pre-set timer is running to end.
Press and hold
1. key for over 2s to
enter general setting menu.
Press
2. / key to choose No.20
menu, LCD displays"APO--OFF".
Turn selector knob to select the desired
3.
setting.
30MIN:Auto power off after 30m
General Setting
Suggestion:Enable this function to check incorrect operation and
malfunctions.
24
8
1HOUR:Auto power off after 1h
2HOUR:Auto power off after 2h
OFF:Disable Auto power off
Press
4. key to conrm and exit.Default:OFF
DTMF Transmitting Time
Press and hold
1. key for over 2s to
enter general setting.
Press
2. / key to choose No.21
menu, LCD displays"SPD--50".
Turn selector knob to select the desired setting.
3.
30/50/100/200/300/500, which indicates the time for sending each
DTMF signal & the interval between each DTMF being sent.
Press
4. key to conrm and exit.Default:50MS.
Squelch level Setup
Setting the radio to a tight squelch level, you can avoid unwanted
signals or noise, but you may not receive a weak signal. Therefore, it will
be better for you to select the normal squelch level
Press and hold
1. key for over 2s to
enter general setting menu.
Press
2. / key to choose No.22
menu, LCD displays"SQL--04".
Turn selector knob to select the desired squelch level.
3.
OF-20 total 21,OF is min setting value(ON)
Press
4. key to conrm and exit.Default:04
Scan Dwell Time Setup
There are 3 kinds of Scan Dwell Time for option.
Press and hold
1. key for over 2s to
enter general setting menu.
Press
2. / key to choose No.23
menu, LCD displays"SCAN--TO".
Turn selector knob to select the desired
3.
Scan Dwell Time.
TO:it pauses 15s once scanning a
matching signal,then resume scan.
CO:it pauses once scanning a matching signal,signal disappeared
then resume scan.
SE:It stops once scanning a matching signal.
Press
4. key to conrm the selection and exit.Default:TO.
LCD Backlight
Press and hold
1. key for over 2s to
enter general setting menu.
Press
2. / key to choose No.24
General Setting
Press ,then turn selector knob also can select the desired
squelch level.
If the transceiver has set at higher squelch level,it may fail to hear
the calling.If set at lower squelch level,the radio will be interfered.
25
8
menu, LCD displays"LAMP--25"
Turn selector knob to select the desired LCD backlight brightness
3.
1-32 total 32 level backlight brightness.
Press
4. key to conrm and exit.Default:25.
Pilot Frequency
This function uses to start repeater .It needs a certain intensity Pilot
Frequency to start dormant repeater.As usual,no need to send pilot
frequency again once repeater started.
Press and hold
1. key for over 2s to
enter general setting.
Press
2. / key to choose No.25
menu, LCD displays"TB--1750".
Turn selector knob to select the desired
3.
pilot frequency.
1750HZ:Pilot frequency1750HZ
2100HZ:Pilot frequency 2100HZ
1000HZ:Pilot frequency 1000HZ
1450HZ:Pilot frequency 1450HZ
Press
4. key to conrm the selection and exit.Default:1750HZ
Display Mode Setup
There are 3 different dispaly modes: Frequency+Channel mode,&
Channel mode&Channel+Name Tag mode, .
Press and hold
1. key for over 2s to enter general setting menu.
Press
2. / key to choose No.26 menu, LCD
displays"DSP—FR".
Turn selector knob to select the desired
3.
mode.
FR:Frequency+Channel mode(Amateur
transceiver mode).
CH:Channel mode(Professional
transceiver mode).
NM:Channel+Name Tag mode(Amateur
transceiver mode),if channel not
named,it displays Frequency+Channel mode.
Press
4. key to conrm and exit.Default:FR.
PIN Setup
Enable this function,you have to insert a matching PIN to enter
into normal status when radio is turned on.(Pin setup by programme
software).
Press and hold
1. key for over 2s to
enter general setting menu.
Press
2. / key to choose No.27
menu, LCD displays"CODE-OF".
Turn selector knob to enable/disable
3.
Pin setup.
ON: Turn on Pin setup
OFF:Turn off Pin setup
Press
4. key to conrm and exit.Default:OFF
This function will be auto-hidden if channel mode locked.(Refer to
programme software)
General Setting
26
8
Address list
You store desired ID and corresponding ID name in address list.The
LCD displays ID corresponding name if radio received ANI calling and
nd matching ID in address list .
Factory Default
If your radio seems to be malfunctioning, resetting the microprocessor
may solve the problem. When performing the reset, you may lose
memory data and stored information. Back up or write down important
data before performing the reset.
General Setting
Press and hold
1. key for over 2s to
enter general setting menu.
Press
2. / key to choose No.29
menu, LCD displays"RESTORE".
Turn selector knob to select the desired
3.
operation.
FACT:Resume factory default for
channel,signaling and general setting.
SETUP:Return initial setup for No.18-
No 27 general setting menu.
Press
4. key to conrm.
Press and hold
1. key for over 2s to
enter general setting menu.
Press
2. / key to choose No.28
menu, LCD displays"BOOK".
Press
3. to enter into ID
setting,press / to select the
desired group (00-127,total is 128 group
ID).Turn selector knob to select desired
number,press conrm and move
cursor to next edition,press to
clear out all digits.
After finishing edition,press
4. to confirm and enter into
edition of current group's ID corresponding name.Turn selector
knob to select desired letter,press to move cursor to next
edition,Press to clear out all letters. 00-127,total 128 group
ID and corresponding ID name.
Press
5. to conrm and return into main menu.Repeat above
Step 3 and Step 4 operations to edit multi-ID and corresponding ID
name.
Press
6. key to return into standby status.
27
9
You can operate the transceiver by keypad or input desired frequency
or channel through the QHM-03 microphone (Note:In professional
transceiver mode,other keys are invalid except PTT,[ / ],
and ).
Keypad Lock
Pull down the slide switch to lock position,The lamp is turned off and
all of keypads is not work except PTT switch.
Transmitting DTMF By Microphone KeyPAD
Switches between VFO and channel mode
In standby,press key to switch between channel mode and
Frequency mode (VFO).
Short Calling
In standby,press to transmit the selected DTMF/2TONE/5TONE
in current channel.
Transmitting DTMF Code:In standby,press ,LCD displays
DTMF data and group.Press [ / ] key to select the
desired transmitting DTMF group,then Press PTT to transmit.
If no DTMF data in current group,LCD displays "EMPTY",press
key again and input desired DTMF code by keypad,press PTT to
transmit and store DTMF data.
Squelch Level
In standby,press
1. ,then press ,LCD displays "SQL" and
current squelch level.
Press
2. / to adjust the desired squelch level.(press
,then press ,turn selector knob also can adjust the desired
squelch level.
Press number key to conrm and exit.
3.
Optional signaling
In standby,press ,then press to add
optional signaling,repeat above operation to
set DTMF,2TONE or 5TONE signaling.
When first bit of Exa byte in
frequency displays "D",it indicates
DTMF function enable.
When first bit of Exa byte in
frequency displays "T",it indicates
2Tone function enable.
Microphone Operation
Slide DTMF key to DTMF position, press and hold the [PTT] key,
transmitting the desired DTMF signaling by the numeric key directly.
(Note:Slide DTMF key to DTMF position,the keyboard is invalid in
standby ).
Function Setup By Microphone Keypad
Squelch off:In standby, press key,
the squelch is disabled when icon
ashed in LCD, Press again to enable
squelch and the icon disappears.
PTT
DOWNUP
Lock Speaker
Numeric Keys
DTMF ON/OFF
28
9
Reverse TX/RX
TX frequency turns to RX frequency & RX
frequency changes to TX frequency. The
signaling will also be reversed if CTCSS/DCS
signaling exited in this channel.
In standby,press
1. ,then press ,LCD displays “REV—OF”.
Press [
2. / ] to select the desired value.
ON:Enable Frequency Reverse
OFF:Disable Frequency Reverse
Press number keys to conrm and exit.
3.
In corresponding mode,press then press key to enter into
scanning.
In scanning mode,press / to change scan direction.
Busy Channel Lockout
BCLO is to disable transmitting while RX signal is received. Once the
channel is busy and you press PTT, the radio will beep as warning and
get back to receiving.
In standby,press
1. ,then press to enter into Busy Channel
Lockout.
Press [
2. / ] to select the desired value.
BU: Enable BCLO, Carrier lockout, transmitting is inhibited when
current channel receives a matching carrier;press [PTT] to emit error
voice prompt.
RL: Enable BTLO, transmitting is inhibited when current channel
receives a matching carrier but dis-matching CTCSS/DCS.press
[PTT] to emit error voice prompt It can transmit in any receiving
status.
OFF: Busy channel lockout is disabled.
Press number keys to conrm and exit.
3.
This function can be temporarily used in channel mode. Once the
radio is turned off or switched to another channel, the temporary
setting will be erased and back to initial settings.
Frequency/Channel scan
Scan Skip
When first bit of Exa byte in frequency displays "F",it
indicates 5Tone function enable.
This function can be temporarily used in Channel mode . Once the
radio is turned off or switched to another channel, the temporary
setting will be erased and back to initial settings.
This function can be temporarily used in Channel mode . Once
the radio is turned off or switched to another channel, the
temporary setting will be erased and back to initial settings.
Microphone Operation
In Channel mode,press then press ,decimal point displayed
between frequency's ten digit and unit digit,it means current channel is
scan skip. Repeat above operation to set scan or scan skip in current
channel.
decimal point displayed between frequency's ten digit and unit
1.
digit,it means current channel is scanned skip.
decimal point is not displayed between frequency's ten digit and
2.
unit digit,it means current channel is scanned.
29
9
TOT (Time-out timer)
The time-out timer limits the amount of transmitting time. When you
reach the time limit which has been programmed by your dealer, your
transmission will be cut off. In order to transmit again, you must release
PTT button to reset the timer.
In standby,press
1. ,then press “LCD displays "TOT-X".
Press [
2. / ] to select the desired value.
Press number key to conrm and exit.
3.
CTCSS/DCS Encode and Decode
In standby,press
1. ,then press to enter into CTCSS/DCS
Encode and Decode.
Repeat above operation to set as below:
2.
LCD displays T icon,it indicates CTCSS encode set in current
channel.
LCD displays T and SQ icon,it indicates CTCSS encode and
decode set in current channel.
LCD displays DCS icon,it indicates DCS encode and decode set
in current channel.
In corresponding icon,press [
3. / ] to select the desired
CTCSS/DCS encode and decode.
Press
4. ` ,or C/SET to conrm and exit.
Talk Around
This function can be temporarily used in Channel mode. Once the
radio is turned off or switched to another channel, the temporary
setting will be erased and back to initial settings.
By Talk Around function,you can directly communicate with other radios
in your group in case the repeater is not activated or when you are out of
the repeater range. The transceiver will transmit by RX frequency with its
CTCSS/DCS signaling.
In standby,press
1. ,then press key,LCD displays “TALK--OF”.
Press [
2. / ] to select the desired setting .
ON:Enable Talk Around
OFF:Disable Talk Around
Press number key to conrm and exit.
3.
This function can be temporarily used in Channel mode . Once the
radio is turned off or switched to another channel, the temporary
setting will be erased and back to initial settings.
Voice Prompt
The prompting tone provides confirmation of entry, error status or
malfunctions of the transceiver. You can enable or disable this function.
In standby,press
1. ,then press ,LCD displays "BEEP--XX”.
Press [
2. / ] to turn on/off BEEP voice prompt.
BEEP—OF :turn off voice prompt
BEEP—ON :turn on voice prompt
Press number key to exit and store.
3.
Microphone Operation
30
9
LCD Backlight
In standby status,press
1. , then press LCD displays"LAMP-
XX" .
Press [
2. / ] to select desired backlight brightness(1-32
levels).
Press number keys to conrm and exit.
3.
Microphone Operation
31
10
Connect DC power cable with car battery.
Connect the optional alarm cable QL-01(A) to the data jack on
1.
the front panel as shown. Secure the other end of the cable to an
object that stays xed in vehicle. (Note: if alarm cable QL-01 (A) is
not enough long, you can choose optional alarm cable QL-01 (B) to
extend).
When transceiver power off by press
2.
key ,the long-distance anti-theft
alarm enable.
Note:The long-distance anti-theft alarm only available when
3.
transceiver power off .
When the alarm cable QL-01(A) or QL-01(B) is removed from the
4.
DATA jack or cut by improper sequence, the alarm function enable
and will alarm as programmed. In alarming,the transceiver will stop
alarm once receiving a matching signal. And alarm again when a
matching signal disappeared.
Restart radio to cancel anti-theft alarming.Reconnect with alarm
5.
cable and turn off radio,the system will return to alarm mode.
This function is mainly use for simple anti-theft alarm device in vehicles.
When the transceiver be removed in an improper manner,the transceiver
will emit and transmit alarming and background voice to system and
other transceiver of the same frequency.
Steering-wheel etc.
Alarm cable [QL-01(B)]
DC power cable
Battery
Alarm cable
[QL-01(A)]
Long-distance Anti-theft Alarm
32
11
This feature will copy the programmed data and parameters in the master unit to slave units. It copies the parameters and memory program settings.
Use optional CP50 cloning cable, connect the cable between the data jacks on both master and slave.
1.
Press and hold key, then press key to enter into cloning mode, LCD displays "
2. CLONE".
Press master unit's [PTT] key, LCD displays "SD XXX", "XXX" indicates data volume in transmitting. Slave unit displays "LD XXX", "XXX" indicates
3.
received data volume. When the transmission is successfully finished, the master and slave unit both display "PASS". Turn off the power,
disconnect the cable and repeat step 2 to step 3 operations to clone the next slave unit.
Cable Clone
If the data is not successfully transmitted, turn off both units, make sure the cable connection is correct and repeat the entire operation from the beginning.
GND DATA TX/RX
Master/Slave stereo plug,3.5mm plug
588
33
12
DCS encode
and decode -
VFO frequency DCS code 023N
Memory channel 0-199 - Output power HI
Offset direction - Key-lock setting OFF
Offset frequency 600KHz TOT OFF
Channel step 12.5KHz APO OFF
CTCSS encode and decode - Squelch Level 4
CTCSS frequency 88.5Hz
Default Setting after Resetting(VHF) Trouble Shooting
Problem Possible Causes and Potential Solutions
(a) Power is on, nothing
appears on Display.
+ and - polarities of power connection
are reversed. Connect red lead to plus
terminal and black lead to minus terminal of
DC power supply.
(b) Fuse is blown. Check and solve problem resulting in blown
fuse and replace fuse with new fuse.
(c) Display is too dim. Dimmer setting is "LAMP-L". Please make the
dimmer setting "LAMP-H".
(d) No sound comes from
speaker.
• Squelch is muted. Decrease squelch level.
• Tone or CTCSS/DCS squelch is active. Turn
CTCSS or DCS squelch off.
(e) Key and Dial do not
function. Key-lock function is activated. Cancel Key-lock
function.
(i) Rotating Dial will not
change memory channel. Transceiver is in CALL mode. Press the VFO
or memory mode.
(g) PTT key is pressed but
transmission does not occur.
• Microphone connection is poor. Connect
microphone properly.
• Antenna connection is poor. Connect antenna
properly.
Maintenance
220-260MHz
13
34
Specications are subject to change without notice due to advancements in
technology.
General
Frequency Range VHF: (220~260MHz)
Number of Channels
200 channels
Channel Spacing
12.5K
Phase-locked Step
5KHz, 6.25KHz, 8.33KHz, 10KHz, 12.5KHz,
Operating Voltage 13.8V DC ±15%
Squelch
Carrier/CTCSS/DCS/5Tone/2Tone/DTMF
Frequency Stability ±2.5ppm
Operating Temperature
-20℃~+60℃
Dimensions(WxHxD) 145 (W) x 47 (H) x 190 (L)mm
Weight about 1.2Kg
Receiver
Sensitivity
(12dB Sinad) ≤0.35μV
Adjacent Channel
Selectivity ≥60dB
Intermodulation ≥60dB
Spurious Rejection ≥70dB
Audio Response +1~-3dB(0.3~2.55KHz)
Hum & Noise ≥40dB
Audio distortion ≤5%
Audio power output ＞2W@10%
Transmitter
Power Output 50W
Modulation 11KΦF3E
Adjacent Channel
Power ≥60dB
Hum & Noise ≥36dB
Spurious Emission ≥60dB
Audio Response +1~-3dB(0.3~2.55KHz)
Audio Distortion ≤5%
Specifications
14
67.0 79.7 94.8 110.9 131.8 156.7 171.3 186.2 203.5 229.1
69.3 82.5 97.4 114.8 136.5 159.8 173.8 189.9 206.5 233.6
71.9 85.4 100.0 118.8 141.3 162.2 177.3 192.8 210.7 241.8
74.4 88.5 103.5 123.0 146.2 165.5 179.9 196.6 218.1 250.3
77.0 91.5 107.2 127.3 151.4 167.9 183.5 199.5 225.7 254.1
Attached Chart
50 groups CTCSS Tone Frequency(Hz) 1024 groups DCS Code.
000 001 002 003 004 005 006 007
010 011 012 013 014 015 016 017
020 021 022 023 024 025 026 027
030 031 032 033 034 035 036 037
040 041 042 043 044 045 046 047
050 051 052 053 054 055 056 057
060 061 062 063 064 065 066 067
070 071 072 073 074 075 076 077
100 101 102 103 104 105 106 107
110 111 112 113 114 115 116 117
120 121 122 123 124 125 126 127
130 131 132 133 134 135 136 137
140 141 142 143 144 145 146 147
150 151 152 153 154 155 156 157
160 161 162 163 164 165 166 167
170 171 172 173 174 175 176 177
200 201 202 203 204 205 206 207
210 211 212 213 214 215 216 217
220 221 222 223 224 225 226 227
230 231 232 233 234 235 236 237
240 241 242 243 244 245 246 247
250 251 252 253 254 255 256 257
260 261 262 263 264 265 266 267
270 271 272 273 274 275 276 277
300 301 302 303 304 305 306 307
310 311 312 313 314 315 316 317
35
36
15 Attached Chart
320 321 322 323 324 325 326 327
330 331 332 333 334 335 336 337
340 341 342 343 344 345 346 347
350 351 352 353 354 355 356 357
360 361 362 363 364 365 366 367
370 371 372 373 374 375 376 377
400 401 402 403 404 405 406 407
410 411 412 413 414 415 416 417
420 421 422 423 424 425 426 427
430 431 432 433 434 435 436 437
440 441 442 443 444 445 446 447
450 451 452 453 454 455 456 457
460 461 462 463 464 465 466 467
470 471 472 473 474 475 476 477
500 501 502 503 504 505 506 507
510 511 512 513 514 515 516 517
520 521 522 523 524 525 526 527
530 531 532 533 534 535 536 537
540 541 542 543 544 545 546 547
550 551 552 553 554 555 556 557
560 561 562 563 564 565 566 567
570 571 572 573 574 575 576 577
600 601 602 603 604 605 606 607
610 611 612 613 614 615 616 617
620 621 622 623 624 625 626 627
630 631 632 633 634 635 636 637
640 641 642 643 644 645 646 347
650 651 652 653 654 655 656 657
660 661 662 663 664 665 666 667
670 671 672 673 674 675 676 677
700 701 702 703 704 705 706 707
710 711 712 713 714 715 716 717
720 721 722 723 724 725 726 727
730 731 732 733 734 735 736 737
740 741 742 743 744 745 746 747
750 751 752 753 754 755 756 757
760 761 762 763 764 765 766 767
770 771 772 773 774 775 776 777
N is positive code, I is negative code, total: 232groups.
This device complies with part 15 of the FCC rules. Operation is subject
to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including
interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help
Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.

Navigation menu