Qixiang Electron Science and Technology AT598V Mobile Radio User Manual

Qixiang Electron Science& Technology Co., Ltd Mobile Radio

User Manual

-LENNAHU-VOLPWRFUNCV/MCALLMHzTX/DCSSCANMINIAT-598Mobile RadiaoFCC ID:T4KAT598VCAL
Thank you for choosing this vehicle transceiver, always provides high quality products, And this transceiver is no exception. As you learn how to use this transceiver, you will find that is pursuing "user friendliness". For example, each time you change the menu no. in Menu mode, you will see a text message on the display that lets you know what you are conguring.Though friendly design for user, this transceiver is technically complicated and some features may be new to you. Consider this manual to be a personal tutorial from the designers, allow the manual to guide you through the learning process now, then act as a reference in the coming years.Do not attempt to configure your transceiver while driving, it is dangerous.This transceiver is designed for a 13.8V DC power supply. Don't use a 24V battery to power on the transceiver.Do not place the transceiver in excessively dusty, humid or wet areas, nor unstable surfaces.Please keep it away from interferential devices (such as TV, generator etc.). Do not expose the transceiver to long periods of direct sunlight nor place it close to heating appliances.If an abnormal odor or smoke is detected coming from the transceiver, turn OFF the power immediately. Contact an Anytone service station or your dealer.Do not transmit with high output power for extended periods; the transceiver may overheat.Please observe the following precautions to prevent re, personal injury, or transceiver damage:Precautions-LENNAHU-VO LPWRFUNCV/MCALLMHzTX/DCSH/LSCANMINIMobile radio
CONTENTSNew and Innovative Features ..............................................1Supplied Accessories/Optional Accessories .....................2Supplied Accessories .......................................................................2Optional Accessories .......................................................................2Initial Installation ..................................................................3Mobile Installation ............................................................................3 DC Power Cable Connection ...........................................................4Power Supply Voltage Display .........................................................6Antenna Connection ........................................................................6Accessories Connections .................................................................7Getting Acquainted ..............................................................8Front panel .......................................................................................8Rear panel .......................................................................................9Display .............................................................................................9Microphone ......................................................................................10Working Mode(Amateur Transceiver or Professional Transceiver) ........................................................................11Basic Operations .................................................................12Switching the Power On/Off ............................................................12Adjusting the Volume ......................................................................12Switch between VFO and Channel mode ....................................... 12Adjusting Frequency/Channel Through Selector Knob ....................12Receiving .........................................................................................12Transmitting .....................................................................................12Transmitting Tone-Pulse ..................................................................13Transmitting Optional Signaling ......................................................13Channel Edit ....................................................................................13Channel Delete ................................................................................13Shortcut Operations .............................................................14Squelch Off/Squelch Off Momentary................................................14Squelch Level Setup ........................................................................14Frequency/Channel Scan ................................................................14Channel Scan ..................................................................................14CTCSS/DCS Encode and Decode Setup ........................................14CTCSS Scan ....................................................................................15DCS Scan ........................................................................................15 Compander (Decrease the background noise and enhance audio clarity ..................................................................................................15Offset Direction and Offset Frequency Setup ..................................16Keypad Lockout ...............................................................................16Current Voltage Enquiry ...................................................................16Auto-Dialer Setup .............................................................................16Transmitting Edited DTMF Tones in the Auto-dialer Memory ...........17General Setting .....................................................................18Frequency Channel Step Setup .......................................................18DTMF, DTMF ANI, 2Tone or 5Tone Signaling ..................................18Sending 2-Tone Call .........................................................................19Sending 5-Tone Call .........................................................................19Sending DTMF call ..........................................................................19Signaling Combination Setup ...........................................................19
CONTENTS Band-width Selection .......................................................................20TX OFF Setup ..................................................................................21Busy Channel Lockout .....................................................................21Editing Channel Name .....................................................................21Reverse TX/RX ................................................................................21Talk Around ......................................................................................22Voice Compander ...........................................................................22Scrambler Setup (Encryption) ..........................................................22Radio's DTMF SELF ID ENQUIRY .................................................22Radio's 5TONE SELF ID ENQUIRY ...............................................23Voice Prompt ....................................................................................23TOT (Time-out timer) .......................................................................23APO (Auto power off) .......................................................................23DTMF Transmitting Time ..................................................................24Squelch Level Setup ........................................................................24Scan Dwell Time Setup ....................................................................24LCD Backlight ..................................................................................24Pilot Frequency ................................................................................25Display Mode Setup .........................................................................25PIN Setup ........................................................................................25Address List ....................................................................................26Factory Default .................................................................................26Microphone Operation .........................................................27Function Setup By Microphone Keypad ...........................................27Squelch Level ..................................................................................27Optional Signaling ...........................................................................27Scan Skip ........................................................................................28Frequency/Channel Scan ...............................................................28Busy Channel Lockout .....................................................................28Reverse TX/RX ................................................................................28 TOT (Time-out timer) ........................................................................29CTCSS/DCS Encode and Decode ...................................................29Talk Around ..................................................................................... 29Voice Prompt ....................................................................................29 LCD Backlight .................................................................................30Long-distance Anti-theft Alarm ..........................................31Cable Clone ..........................................................................32Programming Software Installing and Starting (in windows XP system) ............................................................................33Maintenance ..........................................................................34Default Setting after Resetting(VHF) ...............................................34 Trouble Shooting ..............................................................................34Specications .......................................................................35Attached Chart ......................................................................3650 groups CTCSS Tone Frequency(Hz) ..........................................361024 groups DCS Code. ..................................................................36
11New and Innovative Features598 Mobile Radio has nice housing, stoutness & stability, advanced and reliable functions, perfect & valuable. This amateur mobile radio especially designs for drivers and it pursues company philosophy of innovation and practicality. More functions as follows:Display on a large LCD with adjustable brightness, convenient for nighttime use. There are Amateur operation mode and Professional operation mode for option.Distribute buttons reasonably, convenient for operation. Adopt superior quality material, better technology and high quality radiator to ensure stable and durable operation.200 programmable memorized channels, identied by editing name. Programming different CTCSS, DCS, 2Tone, 5Tone in per channel, rejecting extra calling from other radios. Various scan functions including CTCSS/DCS Scan function. Using  5Tone to send Message, Emergency alarm, Call all, ANI, Remotely kill, Remotely Waken, etc.Automatic calling Identication function by DTMF--ANI or 5Tone--ANI .Scramble function (Optional). Compander function for decrease the background noise and enhance audio clarity, it can set compander ON/OFF per channel. Theft alarm provides extra safety. 
22Supplied AccessoriesAfter carefully unpacking the transceiver, identify the items listed in the table below. We suggest you keep the box and packaging.Transceiver User ManualMicrophone (QHM-03) (with DTMF keyboard)DC Power Cable with Fuse Holder(QPL-01)-LENNAHU-VO LPWRFUNCV/MCALLMHzTX/DCSH/LSCANMINISupplied AccessoriesCar Antenna (QCA-01) Car Antenna (QCA-01) Antenna Gain:0dBi
3To install the transceiver, select a safe, convenient location inside your vehicle that minimizes danger to your passengers and yourself while the vehicle is in motion. Consider installing the unit at an appropriate position so that knees or legs will not strike it during sudden braking of your vehicle. Try to pick a well ventilated location that is shielded from direct sunlight.Install the mounting bracket in the vehicle using the supplied self-1. tapping screws (4pcs) and at washers (4pcs).Position the transceiver, then insert and tighten the supplied 2. hexagon SEMS screws. Double check that all screws are tightened to prevent vehicle  vibration from loosening the bracket or transceiver.3Car bodyWasher (M5)Tapping screw(M5x20mm)Mounting bracketInitial InstallationMobile installation Determine the appropriate angle of the transceiver, using the 3 screw hole positions on the side of the mounting bracket.-LENNAHU-VO LPWRFUNCV/MCALLMHzTX/DCSSCANMINICAL
4Connect the DC power cable to the transceiver's power supply 6. connector.Press the connectors rmly together until the locking tab clicks.If the ignition-key on/off feature is desired(optional feature), use the 3RedBlackExt. Power jackDC power cableInitial InstallationDC Power Cable ConnectionMobile OperationIn many cars,the cigar-lighter plug is always powered. If this is the case, you cannot use it for the ignition key on/off function.The vehicle battery must have a nominal rating of 12V. Never connect the transceiver to a 24V battery. Be sure to use a 12V vehicle battery that has sufficient current capacity. If the current to the transceiver is insufficient, the display may darken during transmission, or transmitting output power may drop excessively.When the ignition key is turned to ACC or ON(Start) position with 7. the radio turned off, the power switch illuminates. The illumination will be turned off when the ignition key is turned to the off position. Route the DC power cable supplied with the transceiver directly 1. to the vehicle's battery terminals using the shortest path from the transceiver.We recommend you do not use the cigarette lighter socket as  some cigarette lighter sockets introduce an unacceptable voltage drop.The entire length of the cable must be dressed so it is isolated from heat, moisture, and the engine secondary (high voltage) ignition system/ cables.After installing cable, in order to avoid the risk of damp, please 2. use heat-resistant tap to tie together with fuse box. Don't forget to reinforce whole cable.In order to avoid the risk of short circuit, please cut down 3. connection with negative (-) of battery, then connect with radio.Confirm the correct polarity of the connections, then attach the 4. power cable to the battery terminals; red connects to the positive (+) terminal and black connects to the negative (-) terminal.Use the full length of the cable without cutting off excess even if  the cable is longer than required. In particular, never remove the fuse holders from the cable.Reconnect any wiring removed from the negative terminal.5. optional QCC-01(For Cigar-Plug connection) cable. Connect one of the cables between the ACC terminal or a Cigar-Plug that operates with the vehicle ignition or ACC switch on the vehicle and EXT POWER jack on the rear side of the unit.Locate the power input connector as close to the transceiver as possible.
53RedBlackRegulated power supply (QRP-01)DC power cable with fuse holder (QPL-01)Regulated power supply (QRP-01)Ext. Power jackACC terminalCigar-Plug connectionInitial InstallationBefore connecting the DC power to the transceiver, be sure to switch the transceiver and the DC power supply OFF.Do not plug the DC power supply into an AC outlet until you make all connections.In order to use this transceiver for fixed station operation, you will need a separate 13.8V DC power supply (not included), power supply( QRP-01) as optional accessories. Please contact local dealer to require.The recommended current capacity of your power supply is 12A.Connect the DC power cable to the regulated DC power supply 1. and ensure that the polarities are correct. (Red: positive, Black: negative).Do not directly connect the transceiver to an AC outlet. Use the supplied DC power cable to connect the transceiver to a regulated power supply.Do not substitute a cable with smaller gauge wires. To turn on the unit, press the power switch manually while it is illuminated. (While ignition key is at ACC or ON position)When the ignition key is turned to ACC or ON position with the 8. radio's power switch on, the unit turns on automatically and the power switch will be lit. Turn the ignition key to OFF position or manually turn the power switch off to shut down the radio.Using extra cable, power consumption:5MAH.9. Without this function, user can turn on/off radio by Power knob.10. Connect the transceiver's DC power connector to the connector 2. on the DC power cable.Press the connectors rmly together until the locking tab clicks .Fixed Station OperationThe EUT can be used on vehicle.
63Initial Installation REPLACING FUSESIf the fuse blows, determine the cause, then correct the problem. After the problem is resolved, replace the fuse. If newly installed fuses continue to blow, disconnect the power cable and contact your autho-rized dealer or an authorized servi-cecenter for assistance. Only use fuses of the specified type and rating, otherwise the transceiver could be damaged.After connecting the transceiver to the power supply, the supply voltage can be displayed on LCD by pressing the FUNC key together with the SCAN key. The display immediately changes as the voltage supply changes, It also displays voltage during transmission.The transceiver will return to its normal operation when the power is switched ON or repeat above operation.Before operating, install an efcient, well-tuned antenna. The success of your installation will depend largely on the type of antenna and its correct installation. The transceiver can give excellent results if the antenna system and its installation are given careful attention.Use a 50Ω impedance antenna and low-loss coaxial feed-line that has a characteristic impedance of 50Ω, to match the transceiver input impedance. Coupling the antenna to the transceiver via feed-lines having an impedance other than 50Ω reduces the efficiency of the antenna system and can cause interference to nearby broadcast television receivers, radio receivers, and other electronic equipment. Fuse Location Fuse Current RatingTransceiver 15ASupplied Accessory DC power cable 20AIf you use the transceiver for a long period when the vehicle battery is not fully charged, or when the engine is OFF, the battery may become discharged, and will not have sufcient reserves to start the vehicle. Avoid using the transceiver in these conditions.The range of displayed voltage is only from 7V to16V DC, because the displayed value is estimated, please use a voltmeter when a more precise reading is desired.Power supply voltage DisplayAntenna ConnectionImportantTransmitting without first connecting an antenna or other matched load may damage the transceiver. Always connect the antenna to the transceiver before transmitting.All xed stations should be equipped with a lightning arrester to reduce the risk of re, electric shock, and transceiver damage.The possible locations of antenna on a car are shown as following:mobile radio mobile radio
73GroundMicrophone connectorErrorhttp://www.qxdz.cnInitial Installation External Speaker MicrophonePC ConnectingIf you plan to use an external speaker, choose a speaker with an impedance of 8Ω. The external speaker jack accepts a 3.5mm (1/8")mono (2-conductor) plug.For voice communications, connect a microphone equipped with an 8-pin modular plug into the modular socket on the front of the main unit. Press rmly on the plug until the locking tab clicks. Attach the supplied microphone hanger in an appropriate location using the screws included in the screw set.To utilize the optional QPS598 software, you must rst connect the transceiver to your PC then using an optional programming cable PC50 (via Data socket ).Please use QPS598 software for programming.External speaker adopt double port BTL, please care about the connecting way. The speaker can not connect with the ground, otherwise the speaker will be fault. The wrong connecting way as the following picture.Accessories ConnectionsSP-01SP-01External speaker[SP-02]Microphone[QHM-04]Antenna[QCA-02]-LENNAHU-VO LPWRFUNCV/MCALLMHzTX/DCSH/LSCANMINI
84NO. KEY FUNCTION1Pow(Power) Power on/Off2VOL Adjust Volume Key3Main Dial Change frequency, memory channel and scan direction etc.4FUN/SET Function Key5V/M/MW Switches between VFO mode and Channel mode6MHz/SHIFT Step Size Key ( step:1MHz)7TS/DCS/LOCK Sets CTCSS and DCS value8Call key9SQL/D Squelch off10 Data Terminal Data reading/writing, cloning and theft alarm functions11 TX lights during Transmitting12 Mic.connector Microphone connection portNO. KEY FUNCTION4FUN/SET Conrms the selective functions and exit5V/M/MW Stores data into channels6MHz/SHIFT Sets offset direction and offset frequency7TS/DCS/LOCK Sets Keypad lock function89SQL/D Compander mode on/off NO. KEY FUNCTION1Pow(Power) Reset to factory default settings 5V/M/MW Erase the memory 67TS/DCS/LOCK Auto dialer 8Enters clone data function modeSQL/D Enters power supply voltage indication mode NO. KEY FUNCTION4FUN/SET Press and hold for 2s to enter the Setting mode 9SQL/D Monitor modeGetting AcquaintedFront panel Press FUNC key until icon appears then press the following key.Press FUNC key and following key together to activate following function:Functions that require continuous pressing following key to be activatedBasic FunctionsPWRFUNCV/MCALLMHzTX/DCSSC ANMINI-LENNAHU-VOLpower CALCALCALCAL
94NO. KEY FUNCTION1Ext. Power JackTerminal for connecting optional cable QCC01 for use with ignition key On/Off function.The radio will auto power on when car is driving. The radio will auto power off when car stops. 2Ext.Speaker Terminal Terminal for optional external speaker SP01 3Antenna Connector Connection for 50Ω coaxial cable and antenna.NO. KEY FUNCTION1 SQL Squelch level.2 MIn channel mode.3 Indicates the channel number in channel mode.4Decimal pointChannel skip.5Decimal point Indicates the decimal point of frequency and the scanning function.6 Indicates the frequency or memory name.7Signal is being received or monitor.8Signal strength of receiving and transmitting.9Compander.10 Keypad lock .11 DCS Set DCS function.12 Set CTCSS function.13 + _Offset frequency direction.14 Scramble.15 A Auto power off.Getting AcquaintedDISPLAYRear panel4 13213 13 101112 1473
104Key Pad Serial Data+5VDOWNUPMIC GNDMICPTTGNDmicrophone MIC Connector Diagram(in the front view of connector)Getting AcquaintedChannel Down Channel UPMicrophone cableMicPTTConnector
115According to practical application, you can set the radio works as Amateur Transceiver mode or Professional Transceiver mode. There are also 2 levels operation menu to set functions as you need. It is easy and convenient (From No.1 to No.15 are channel function setup, From No.15 to No.29 are general setting setup). Working Mode:1. By programming software: A. In PC software's "General Setting" menu, choose "Display Mode" to select Amateur Transceiver mode or Professional Transceiver mode.By manual setupB. : Please refer to "Display Mode" in Page 25.Amateur Transceiver Mode: 2. Except setting as "CH" mode, others considered as Amateur transceiver mode. Under this mode, press V/M key to switch between Channel mode and VFO mode . Professional Transceiver Mode:3. When set display mode as "CH", it enters into Professional Transceiver mode.At this mode, except scan, other shortcut operation can't operate. And from No.1-17 menu in function setting will be auto-hidden, they should be set by PC software.If there is corresponding name for current channel, the LCD will display current channel name Otherwise, it shows current channel number. (As pic 4) (As pic 5) Under every mode, from No.18-29 menu in 4. general setting can be changed and saved.VFO Mode(Frequency mode)C. : This mode shows only frequency on the display. Shortcut operation and Channel setting will be changed & stored as the latest value permanently. Once the radio is turned off or changed to new VFO frequency, the latest setting is remained until next change.(As pic 3) If transceiver programmed as professional transceiver mode and locked, you can't return to amateur transceiver mode by manual operation from general setting.(Pic 1)(Pic 2)(Pic 4)(Pic 5)Frequency + Channel modeA. : When set display as "FR", it enters into Frequency+Channel mode, new setting of channel operation and shortcut operation can be temporarily used by user. Once the radio is turned off or switched to another channel, the temporary setting will be erased and back to initial settings.(As pic 1)Channel+Name Tag ModeB. : When set display as "NM", it enters into Channel+Name Tag mode. At this mode, it will display corresponding channel name when the current channel is edited with name. Otherwise, it will display frequency+channel. Its operations are the same as frequency + channel mode.(As pic 2)(Pic 3)WORKING MODE (AMATEUR TRANSCEIVER OR PROFESSIONAL TRANSCEIVER)
12In standby, pressV/Mkey or Microphone's MINI key until appear , this indicates current channel in channel mode. Repeat above 6PWR KEYDialFrequency decreaseFrequency increaseMinVolumeMaxVolumeBasic Operations Switching The Power On/OffAdjusting The Volume Switch between VFO and Channel modeAdjusting Frequency/Channel THROUGH SELECTOR KNOBReceivingAccording to the option selected during installation Press PWR the switch or turn the ignition key to ACC (speed up) or ON (startup) position to power on radio. Press the PWR key for 1s or turn the ignition key to OFF position to turn off.When the channel you are operating is called, the screen shows and field intensity, in this way, you can hear the calling from transmitting party.Under frequency (VFO) mode, you can 1. change the current frequency to the desired one through selector knob; Turn clockwise to increase frequency; turn counterclockwise to decrease. Every gear will increase or decrease one step. Press key, the decimal point of Turn the VOL knob clockwise to increase the audio level, counterclockwise to decrease. During communication, volume can be adjusted more accurate.five step size available for this radio.If the transceiver has set at higher squelch level, it may fail to hear the calling.operation to switch between Frequency mode (VFO) and Channel mode.frequency in screen will be auto-hidden. In this status, turn selector knob or Microphone [ / ] key will increase or decrease frequency quickly by 1MHz step.Under channel mode, you can change the current channel to the 2. desired one through selector knob, clockwise turn to the forward channel, anticlockwise turn to the backward channel. In relative working mode, Microphone's [ / ] key has same function for adjusting frequency and channel.TransmittingPress and hold MINI key or press MIC's key to monitor for a while to conrm the channel desired is not busy. Release SCAN or press Mic's MINI key to return standby status, then press and hold [PTT] key to speak into microphone.When the channel you are operating is called, the screen shows BUSY and field intensity, you can't hear the calling from transmitting party, it means current channel receives a matching carrier but unmatching signaling(Refer to CTCSS/DCS encode and decode or Optional Signaling setup)./DCSS C ANMI N IVOLPWRFUN CV/MC A LLMHz-LENNAHU-PWRFUN CV/MC A LLMHz-LENNAHU-5k, 6.25k, 8.33K,10k, 12.5k, total CAL
13Basic Operations Transmitting Tone-PulseTransmitting OPTIONAL SIGNALING Press and hold [PTT] key, then press Microphone [ ] key to transmit current selected tone-pulse signal. Press and hold [PTT] key, then press Microphone key or press CALL key in front panel or press Mic's MINI key to transmit pre-stored and selected DTMF/2Tone/5Tone optional signaling.Channel EditChannel DeleteUnder frequency mode (VFO), turn 1. selector knob to select the desired frequency or input frequency by MIC's numeric keys.Press2. TX/DCS key to enter CTCSS/DCS signaling setup, turn selector knob to select the desired signaling.Press 3. FUNC key, LCD appears , icon and current channel number, icon ashing means current channel is Under channel mode, turn selector knob to select channel which 1. you want to delete.Press2. FUNC key and V/M key together, current channel will be deleted and emitted a prompt voice. icon ashing means current channel is deleted.empty.Turn selector knob to select the desired channel number to store.4. Press 5. V/M key, , icon and channel number disappears and emit a prompt voice, thus the channel storage succeed.6Please hold the microphone approximately 2.5-5.0cm from your lips , and then speak into the microphone in your normal speaking voice to get best timbre.Press and hold [PTT] key, LED lights RED and power intensity showed in screen indicates it is transmitting, release to receive.
147Shortcut OperationsSquelch level SetupFrequency/Channel ScanChannel ScanCTCSS/DCS Encode and Decode setupSetting the radio to a tight squelch level, you can avoid unwanted signals or noise, but you may not receive a weak signal. Therefore, it will be better for you to select the normal squelch level.In frequency (VFO) mode, this function is designed to monitor signal of every communicative frequency point of transceiver "step size" you have set. In channel mode, this function is designed to monitor signal in every channel. In channel mode, Press 1. V/M key for 1s to enter into channel scan. Repeatedly press TX/DCS key to check whether set CTCSS/DCS encode and decode in current channel or not.While standby, press 1. SCAN key and turn selector knob until LCD appears and current squelch level.Turn selector knob or press MIC [ 2. / ] key to set desired squelch level.Press any key except 3. PWR and FUNC key to exit. Frequency ScanIn VFO mode, press 1. V/M for 1s to enter into frequency scan.Turn selector knob or press Microphone 2. [ / ] key to change scan direction.Press any key except 3. PWR and FUNC key to exit.Turn selector knob or press Microphone 2. [ / ] key to change scan direction.Press any key except 3. PWR and FUNC key to exit. squelch off/squelch off momeNTARYSCAN key programmed as Squelch Off or Squelch Off Momentary to monitor the weak signal.Squelch Off: Press1. SCAN key to disable squelch, press SCAN key again to resume squelch.Squelch Off Momentary: Press and hold2. SCAN key to disable squelch, release SCAN key to resume squelch.The above functions should be set in programme software.When LCD appears 1. icon, it means current channel with CTCSS encode, turn selector knob or press Microphone's [ / ] key to select desired CTCSS encode.When LCD appears2. and icon, it means current channel with CTCSS encode and decode, turn selector knob or press Microphone's [ / ] to select desired CTCSS code.
157Shortcut OperationsCTCSS SCANRepeatedly press TX/DCS key until LCD displays and icons, then hold TX/DCS key for 1S to enter into CTCSS scanning. Once nding a matching CTCSS signaling, it will stop for 15s then scan again.Under channel mode, this operation can be temporarily used by user. Once the radio is turned off or switched to another channel, the temporary setting will be erased.When LCD appears 3. icon, it means current channe can be set with DCS encode and decode together, turn selector knob or press Microphone's [ / ] to select desired DCS encode and decode.CTCSS:62.5-254.1, Total 51groups; DCS:000N-777I total 1024 4. groups. N is positive code, I is inverse code.Press any key except 5. FUNC, PWR and TX/DCS keys to return into standby status. Repeatedly press TX/DCS key until LCD displays DCS icons, then hold TX/DCS key for 1S to enter into DCS scanning. Once nding a matching DCS signaling, it will stop for 15s then scan again.Compander function will decrease the background noise and enhance audio clarity, especially in long range communication.Press 1. FUNC key, then press SCAN key to turn on compander function, repeat above operation again to turn off compander function.Compander (Decrease the background noise and ENHANCE AUDIO CLARITY)When LCD appears 2. icon, enable compander in current channel.When LCD doesn't display 3. icon, disable compander in current channel.DCS SCAN
16Press 1. FUNC key until LCD displays icon, then press TX/DCS key until, LCD displays icon, it indicates keypad lockout function is valid.Repeat above operation, 2. icon disappears, it indicates keypad lockout function is invalid.This will automatically transmit pre-programmed and stored DTMF tones. And they are often used to remote control electronic devices or AUTOPATCH phone systems available on some repeater.Press and hold 1. FUNC key, then press TX/DCS key to enter the auto-dialer enquiry mode, LCD displays current default data and current group displayed on left. If no data in current group, it shows "EMPTY".Turn selector knob to choose group you desired. Total:16 group, 2. Press and hold 1. FUNC key, then press SCAN key, LCD displays current battery voltage.Repeat above operation to return into 2. VFO or Channel mode.When LCD displays " " icon, it indicates negative offset, which 4. means transmitting frequency lower than receiving frequency.Turn selector knob or Mic's [ 5. / ] key to change offset frequency, offset frequency changed as per stepping.Press any key except 6. FUNC and MHz key to exit into standby.Press 1. FUNC key until the icon displays on the LCD, then press MHz key, LCD displays offset direction and offset frequency.Repeatedly press 2. MHz key to select positive offset and negative offset.When LCD displays " " icon, it indicates 3. positive offset, which means transmitting frequency higher than receiving frequency.7Avoiding unintentional operation, this function will lock main keys, all keys except SCAN / FUNC and PWR key are invalid.KEYPAD LOCKOUTCurrent Voltage ENQUIRYAuto-Dialer SetupShortcut OperationsThis function will display Current Battery Voltage.Under channel mode, this operation can be temporarily used by user. Once the radio is turned off or switched to another channel, the temporary setting will be erased.In voltage display mode, all functions and channel or frequency selection are invalid.Repeater receives a signal(UP-LINK) on one frequency and re-transmits on another frequency(DOWN-LINK). The difference between these two frequencies is called the offset frequency. If the UP-LINK frequency higher than DOWN-LINK frequency, the direction is positive, If it is lower, the shift direction is negative.Offset Direction and offset frequency setup
177Shortcut OperationsPress 1. FUNC key, then press TX/DCS key to enter into auto-dialer enquiryTurn selector knob to select desired transmitting group2. Press PTT or 3. SCAN key to transmit current selected DTMF tones.Transmitting Edited DTMF tones in the Auto-dialer memory01-16.Press 3. SCAN key to enter into editing of current group, press MIC's numeric keys to set your desired data.The display scrolls when the 7th digit 4. is entered. The numbers 0-9, --, A-D, * and # can be stored up to a total of 23 digits.After editing, press PTT or5. SCAN key to send current group and store edited DTMF signaling. Press SCAN to exit and store.
18 Press and hold 1. FUNC key for over 2s to enter general setting menu.Press 2. CALL / SCAN key to choose No.01 menu, LCD displays "STP--125".Turn selector knob to select the desired 3. frequency channel step. Channel step: 5K, 6.25K, 8.33K, 10K, Press 4. TX/DCS key to conrm and exit.Press and hold 1. FUNC key for over 2s to enter general setting menu.Press 2. CALL or SCAN to select the desired function option.Turn selector knob to select the desired setup.3. Press 4. TX/DCS to conrm and exit.Meanwhile, if you want to edit channel name or start up menu, press V/M or TX/DCS to move forward or backward, Press MHz to store and exit.Only in frequency (VFO) mode, this function is valid. Turn selector knob to select frequency or frequency scanning which is restricted by frequency step size. 8General SettingFrequency Channel Step SetupThis function is auto-hidden in channel mode. DTMF, DTMF ANI, 2Tone or 5Tone SignalingDTMF/5Tone/2Tone signalling function as similarily as CTCSS/DCS. Without receiving correspondent tone signalling, the speaker will remain mute. DTMF and 5Tone signalling can be applied for other advanced features such as ANI, PTT ID, group call, remotely stun, remotely kill, waken,...etc.. The signalling edition must be done through programming software. Please refer to the HELP option in the programming software to know how to operate these features.Press and hold 1. FUNC key for over 2s to enter into general setting menu.Press 2. CALL / SCAN to choose No.2 menu, LCD displays "T-OFF".Turn selector knob to 3. select the desired setup." DTMF": The channel will be mute by a DTMF signal. The speaker won’t be open until receiving a correspondent DTMF signal. Hold "PTT" then press [UP] or press CALL directly to transmit the pre-stored DTMF signaling. In Profession transceiver mode, the functions from No.1 to No.17 will be auto-hidden.In DTMF signaling mode,press CALL for 2s until LCD displays "AN---", turn selector knob to select desired digit (the other party ID).In this mode, press TX/DCS to conrm exist digit and move cursor to next, press V/M to forward cursor.After editing, press CALL key to operate ANI call." 2TONE": The channel will be mute by a 2-Tone signal. The speaker won’t be open until receiving a correspondent 2-Tone signal. Hold "PTT" then press [UP] or press CALL directly to transmit the pre-stored 2-Tone signaling." 5Tone": The channel will be mute by a 5-Tone signal. The Speaker won’t be open until receiving a correspondent 5-Tone signal. Hold "PTT" then press [UP] or 12.5K
198Sending 5-Tone CallPress 2. CALL / SCAN key to choose No.04 menu, LCD displays "5TON XX", "XX" indicates the group in the list.Turn selector knob to select the desired sending 5TONE group, 3. Press PTT to transmit selected group. Total:100groups, 00-99, Default:00.4. Press 5. TX/DCS key to conrm and exit. General SettingContent and name of 5TONE will be edited by programming software. This radio only query edited group or name. If there is corresponding name for 5TONE, this operation will display 5TONE corresponding name.Press CALL directly to transmit the pre-stored 5-Tone signaling.In 5Tone signaling mode, press CALL for 2s until LCD displays "AN---", turn selector knob to select desired digit(caller ID). In this mode, press TX/DCS to confirm exist digit and move cursor to next, press V/M to forward cursor.After editing, press CALL key to operate ANI call.Press 4. TX/DCS key to conrm and exit. Sending 2-Tone CallPress and hold 1. FUNC key for over 2s to enter general setting menu.Press 2. CALL / SCAN key to choose No.03 menu, LCD displays "2TON XX", "XX" indicates the group in the list.Turn selector knob to select the desired 3. sending 2TONE group, Press PTT to transmit selected group. Total: 32groups, 00-31, Default: 00.4. Press 5. TX/DCS key to conrm and exit. Content and name of 2TONE will be edited by programming software.This radio only query edited group or name. If there is corresponding name for 2TONE, this operation will display 2TONE corresponding name.Press and hold 1. FUNC key for over 2s to enter general setting menuSending DTMF callPress and hold 1. FUNC key for over 2s to enter general setting menu.Press 2. CALL / SCAN key to choose No.05 menu, LCD displays "DTMF XX", "XX" indicates the group in the list.Turn selector knob to select the desired 3. sending DTMF group, Press PTT to transmit selected group. Total: 16groups, 00-16, Default: 00.4. Press 5. TX/DCS key to conrm and exit.Signaling Combination setupThis function is to improve the level of protecting the radio against receiving irrelative signal. Press and hold 1. FUNC key for over 2s to enter general setting menu.
208If select "SQ", it indicates you can hear the calling from caller when receive a matching carrier.If LCD displays " CTC", it indicates you can hear the calling from caller when receive a matching carrier and CTCSS/DCS signaling.If LCD displays " TON", it indicates you can hear the calling from caller when receive a matching carrier and DTMF/2TONE/5TONE signaling.If LCD displays " C T", it indicates you can hear the calling from caller when receive a matching carrier and CTCSS/DCS and DTMF/2TONE/5TONE signaling.If LCD displays " C/T", it indicates you can hear the calling from caller when receive a matching carrier and either CTCSS/DCS and DTMF/2TONE/5TONE signaling.Press 4. TX/DCS key to conrm and exit. General SettingPress 2. CALL / SCAN key to choose No.06 menu, LCD displays "SPK--SQ".Turn selector knob to select the desired 3. combination.This setting will be set together with adding optional signaling and CTCSS/DCS.
218TX OFF SETUPDisable this function, it is invalid to press PTT, current channel only works in RX mode.Press and hold 1. FUNC key for over 2s to enter general setting menu.Press 2. CALL / SCAN key to choose No.09 menu, LCD displays "TX-ON".Turn selector knob to select the desired 3. setting.ON: In current channel, Press PTT to transmit. OFF: In current channel, Press PTT is invalid.Press 4. TX/DCS key to conrm and exit. Default:ON.Busy Channel LockoutBCLO is to disable transmitting while RX signal is received. Once the channel is busy and you press PTT, the radio will beep as warning and get back to receiving.Press and hold 1. FUNC key for over 2s to enter general setting menu.Press 2. CALL / SCAN key to choose No.10 menu, LCD displays "LOCK--OFF".Turn selector knob to select the desired setting.3. BU: Enable BCLO, Carrier lockout, transmitting is inhibited when current channel receives a matching carrier; press [PTT] to emit error voice prompt and back to receiving status.RL: Enable BTLO, transmitting is inhibited when current channel receives a matching carrier but dis-matching CTCSS/DCS. Press [PTT] to emit error voice prompt and back to receiving status.OFF: Busy channel lockout is disabled.It can transmit in any receiving status.Press 4. TX/DCS key to conrm and exit.Press and hold 1. FUNC key for over 2s to enter general setting menu.Press 2. CALL / SCAN key to choose No.11 menu, LCD displays cursor and ashing.Turn selector knob to select the desired letter, press 3. TX/DCS key to confirm selected letter and enter into next edition, Press V/M to return forward edition.After edition, press 4. TX/DCS key to exit.Reverse TX/RXGeneral SettingEditing Channel NAME In Frequency (VFO) mode, this function will be auto-hidden.TX frequency turns to RX frequency & RX frequency changes to TX frequency. The signaling will also be reversed if CTCSS/DCS signaling exited in this channel.Press and hold 1. FUNC key for over 2s to enter general setting menu
228Press 2. CALL / SCAN key to choose No.12 menu, LCD displays "REV—OF".Turn selector knob to select the desired 3. setting.ON: Enable Frequency Reverse OFF: Disable Frequency Reverse.After edition, press 4. TX/DCS key to exit.Talk Around Press 2. CALL / SCAN key to choose No.14 menu, LCD displays "COMP--OF".Turn selector knob to select the desired 3. setting.ON: Enable companderOFF: Disable companderPress 4. TX/DCS key to conrm and exit. Default:OFFScrambler setup (Encryption)An analog voice inversion scrambler can be equipped as optionals. This special audio process can offer a more confidential communication. Other radios at same frequency will receive only disordered noises.General SettingBy Talk Around function, you can directly communicate with other radios in your group in case the repeater is not activated or when you are out of the repeater range. The transceiver will transmit by RX frequency with its CTCSS/DCS signaling.Press and hold 1. FUNC key for over 2s to enter general setting menu.Press 2. CALL / SCAN key to choose No.13 menu, LCD displays "TALK—OF".Turn selector knob to select the 3. desired setting.ON: Enable Talk Around OFF: Disable Talk AroundAfter edition, press 4. TX/DCS key to exit.Voice Compander Enable this function to reduce background noise and enhance audio clarity, especially in long range communication.Press and hold 1. FUNC key for over 2s to enter general setting menuRadio's DTMF SELF ID ENQUIRYThis function is optional. Press and hold 1. FUNC key for over 2s to enter general setting menu.Press 2. CALL / SCAN key to choose No.16 Press and hold 1. FUNC key for over 2s to enter general setting menu.Press 2. CALL / SCAN key to choose No.15 menu, LCD displays "SCR--OF".Turn selector knob to select the desired 3. setting.ON:Enable ScramblerOFF:Disable ScramblerPress 4. TX/DCS key to conrm and exit.Default:OFF.
238menu, LCD displays "D--XXX", "XXX" is radio's DTMF SELF ID. Press 3. TX/DCS key to conrm and exit.Radio's 5TONE SELF ID ENQUIRYPress and hold 1. FUNC key for over 2s to enter general setting menu.Press 2. CALL / SCAN key to choose No.17 menu, LCD displays "F--XXXXX", "XXXXX" is radio's 5TONE SELF ID. Press 3. TX/DCS key to conrm and exit.Voice PromptThe prompting tone provides confirmation of entry, error status or malfunctions of the transceiver. You can enable or disable this function.Press and hold 1. FUNC key for over 2s to enter general setting menu.Press 2. CALL / SCAN key to choose No.18 menu, LCD displays "BEEP--ON".Turn selector knob to select the desired 3. setting.ON: Enable voice promptOFF: Disable voice promptPress 4. TX/DCS key to conrm and exit. Default:ON.TOT (Time-out timer)The time-out timer limits the amount of transmitting time. When you reach the time limit which has been programmed by your dealer, your transmission will be cut off. In order to transmit again, you must release PTT button to reset the timer.Press and hold 1. FUNC key for over 2s to enter general setting menu.Press 2. CALL / SCAN key to choose No.19 menu, LCD displays "TOT--3".Turn selector knob to select the desired 3. setting.Timer: 1-30min, each level 1min OFF: Disable TOTPress 4. TX/DCS key to conrm and exit. Default:3.APO (Auto power off)Once APO is activated, the radio will be automatically switched off when the pre-set timer is running to end.Press and hold 1. FUNC key for over 2s to enter general setting menu.Press 2. CALL / SCAN key to choose No.20 menu, LCD displays "APO--OFF".Turn selector knob to select the desired 3. setting. 30MIN: Auto power off after 30m 1HOUR: Auto power off after 1hGeneral SettingSuggestion:Enable this function to check incorrect operation and malfunctions.
248 2HOUR: Auto power off after 2h OFF: Disable Auto power offPress 4. TX/DCS key to conrm and exit. Default:OFFDTMF Transmitting TimePress and hold 1. FUNC key for over 2s to enter general setting.Press 2. CALL / SCANkey to choose No.21 menu, LCD displays "SPD--50".Turn selector knob to select the desired 3. setting. 30/50/100/200/300/500, which indicates the time for sending each DTMF signal & the interval between each DTMF being sent.Press4. TX/DCS key to conrm and exit. Default:50MS.Squelch level SetupSetting the radio to a tight squelch level, you can avoid unwanted signals or noise, but you may not receive a weak signal. Therefore, it will be better for you to select the normal squelch levelPress and hold 1. FUNC key for over 2s to enter general setting menu.Press 2. CALL / SCAN key to choose No.22 menu, LCD displays "SQL--04".Turn selector knob to select the desired 3. squelch level. OF-20 total 21, OF is min setting value(ON)Press 4. TX/DCS key to conrm and exit. Default:04Scan Dwell Time SetupThere are 3 kinds of Scan Dwell Time for option.Press and hold 1. FUNC key for over 2s to enter general setting menu.Press 2. CALL / SCAN key to choose No.23 menu, LCD displays "SCAN--TO".Turn selector knob to select the desired Scan Dwell Time.3. TO:It pauses 15s once scanning a matching signal, then resume scan.CO:It pauses once scanning a matching signal, signal disappeared then resume scan.SE:It stops once scanning a matching signal.Press 4. TX/DCS key to conrm the selection and exit.Default:TO.LCD BacklightPress and hold 1. FUNC key for over 2s to enter general setting menu.Press 2. CALL / SCAN key to choose No.24 menu, LCD displays "LAMP--25".General SettingPress SCAN, then turn selector knob also can select the desired squelch level.If the transceiver has set at higher squelch level, it may fail to hear the calling. If set at lower squelch level, the radio will be interfered.
258Turn selector knob to select the desired LCD backlight brightness 3. 1-32 total 32 level backlight brightness.Press 4. TX/DCS key to conrm and exit. Default:25.Pilot FrequencyThis function uses to start repeater. It needs a certain intensity Pilot Frequency to start dormant repeater. As usual, no need to send pilot frequency again once repeater started.Press and hold 1. FUNCkey for over 2s to enter general setting. Press 2. CALL / SCANkey to choose No.25 menu, LCD displays "TB--1750".Turn selector knob to select the desired 3. pilot frequency.1750HZ:Pilot frequency1750HZ2100HZ:Pilot frequency 2100HZ1000HZ:Pilot frequency 1000HZ1450HZ:Pilot frequency 1450HZPress 4. TX/DCS key to conrm the selection and exit. Default:1750HZDisplay Mode SetupThere are 3 different dispaly modes: Frequency+Channel mode, & Channel mode&Channel+Name Tag mode.Press and hold 1. FUNC key for over 2s to enter general setting menu.Press 2. CALL / SCAN key to choose No.26 menu, LCD displays "DSP—FR".Turn selector knob to select the desired 3. mode.FR:Frequency+Channel mode(Amateur transceiver mode).CH:Channel mode(Professional transceiver mode).NM:Channel+Name Tag mode(Amateur transceiver mode), if channel not named, it displays Frequency+Channel mode.Press 4. TX/DCS key to conrm and exit. Default:FR.PIN Setup Enable this function, you have to insert a matching PIN to enter into normal status when radio is turned on.(Pin setup by programme software).Press and hold 1. FUNC key for over 2s to enter general setting menu.Press2. CALL / SCAN key to choose No.27 menu, LCD displays "CODE-OF".Turn selector knob to enable/disable 3. Pin setup.ON: Turn on Pin setupOFF:Turn off Pin setupPress 4. TX/DCS key to conrm and exit.Default:OFFThis function will be auto-hidden if channel mode locked.(Refer to programme software)General Setting
268Address list You store desired ID and corresponding ID name in address list. The LCD displays ID corresponding name if radio received ANI calling and nd matching ID in address list.Factory DefaultIf your radio seems to be malfunctioning, resetting the microprocessor may solve the problem. When performing the reset, you may lose memory data and stored information. Back up or write down important data before performing the reset.General SettingPress and hold 1. FUNC key for over 2s to enter general setting menu.Press 2. CALL / SCAN key to choose No.29 menu, LCD displays "RESTORE".Turn selector knob to select the desired 3. operation.FACT:Resume factory default for channel, signaling and general setting.SETUP:Return initial setup for No.18-No.27 general setting menu.Press 4. MHz key to conrm.You can operate the transceiver by keypad or input desired frequency Press and hold 1. FUNC key for over 2s to enter general setting menu.Press 2. CALL / SCAN key to choose No.28 menu, LCD displays "BOOK".Press 3. MHz to enter into ID setting, press CALL / SCAN to select the desired group (00-127, total is 128 group ID).Turn selector knob to select desired number, press TX/DCS conrm and move cursor to next edition, press V/M to clear out all digits. After finishing edition, press 4. MHz to conrm and enter into edition of current group's ID corresponding name.Turn selector knob to select desired letter, press TX/DCS to move cursor to next edition, Press MHz to clear out all letters. 00-127, total 128 group ID and corresponding ID name.Press 5. MHz to confirm and return into main menu. Repeat above Step 3 and Step 4 operations to edit multi-ID and corresponding ID name.Press 6. TX/DCS key to return into standby status.
279or channel through the QHM-03 microphone (Note:In professional transceiver mode, other keys are invalid except PTT, [ / ], CALL and SCAN).Keypad LockPull down the slide switch to lock position, the lamp is turned off and all of keypads is not work except PTT switch.Transmitting DTMF By Microphone KeyPAD Switches between VFO and channel mode In standby, press FUNC key to switch between channel mode and Frequency mode (VFO).Short CallingIn standby, press CALL to transmit the selected DTMF/2TONE/5TONE in current channel.Transmitting DTMF Code:In standby, press SCAN , LCD displays DTMF data and group. Press [ / ] key to select the desired transmitting DTMF group, then Press PTT to transmit.If no DTMF data in current group, LCD displays "EMPTY", press SCAN key again and input desired DTMF code by keypad, press PTT to transmit and store DTMF data.Squelch LevelIn standby, press 1. FUNC , then press MINI , LCD displays "SQL" and current squelch level.Press 2. / to adjust the desired squelch level. (press FUNC , then press MINI , turn selector knob also can adjust the desired squelch level.Press number key to conrm and exit.3. Optional signaling In standby, press FUNC , then press H/L to add optional signaling, repeat above operation to set DTMF, 2TONE or 5TONE signaling.When rst bit of Exa byte in frequency displays "D", it i ndicates DTMF function enable. When rst bit of Exa byte in frequency displays "T", it indicates 2Tone function enable. Microphone OperationSlide DTMF key to DTMF position, press and hold the [PTT] key, transmitting the desired DTMF signaling by the numeric key directly.(Note:Slide DTMF key to DTMF position, the keyboard is invalid in standby).Function Setup By Microphone KeypadSquelch off:In standby, press MINI key, the squelch is disabled when icon ashed in LCD, Press MINI again to enable squelch and the icon disappears.Channel Down Channel UPMicPTT
289Reverse TX/RXTX frequency turns to RX frequency & RX frequency changes to TX frequency. The signaling will also be reversed if CTCSS/DCS signaling exited in this channel.In standby, press 1. FUNC , then press MINI , LCD displays "REV—ON".Press [ 2. / ] to select the desired value.ON:Enable Frequency ReverseOFF:Disable Frequency ReversePress number keys to conrm and exit.3. In corresponding mode, press FUNC then press MINI key to enter into scanning. In scanning mode, press / to change scan direction.Busy Channel LockoutBCLO is to disable transmitting while RX signal is received. Once the channel is busy and you press PTT, the radio will beep as warning and get back to receiving.In standby, press 1. FUNC , then press MINI to enter into Busy Channel Lockout.Press [ 2. / ] to select the desired value.BU: Enable BCLO, Carrier lockout, transmitting is inhibited when current channel receives a matching carrier; press [PTT] to emit error voice prompt.RL: Enable BTLO, transmitting is inhibited when current channel receives a matching carrier but dis-matching CTCSS/DCS. Press [PTT] to emit error voice prompt It can transmit in any receiving status.OFF: Busy channel lockout is disabled.Press number keys to conrm and exit.3. This function can be temporarily used in channel mode. Once the radio is turned off or switched to another channel, the temporary setting will be erased and back to initial settings. Frequency/Channel scan Scan Skip When rst bit of Exa byte in frequency displays "F", it indicates 5Tone function enable.This function can be temporarily used in Channel mode. Once the radio is turned off or switched to another channel, the temporary setting will be erased and back to initial settings. This function can be temporarily used in Channel mode. Once the radio is turned off or switched to another channel, the temporary setting will be erased and back to initial settings. Microphone OperationIn Channel mode, press FUNC then press MINI , decimal point displayed between frequency's ten digit and unit digit, it means current channel is scan skip. Repeat above operation to set scan or scan skip in current channel.decimal point displayed between frequency's ten digit and unit digit, 1. it means current channel is scanned skip.decimal point is not displayed between frequency's ten digit and 2. unit digit, it means current channel is scanned.
299TOT (Time-out timer)The time-out timer limits the amount of transmitting time. When you reach the time limit which has been programmed by your dealer, your transmission will be cut off. In order to transmit again, you must release PTT button to reset the timer.In standby, press 1. FUNC, then press MINI LCD displays "TOT-X". Press [ 2. / ] to select the desired value.Press number key to conrm and exit.3. CTCSS/DCS Encode and DecodeIn standby, press 1. FUNC , then press MINI to enter into CTCSS/DCS Encode and Decode.Repeat above operation to set as below:2. LCD displays  icon, it indicates CTCSS encode set in current channel.LCD displays  and icon, it indicates CTCSS encode and decode set in current channel.LCD displays DCS icon, it indicates DCS encode and decode set in current channel.In corresponding icon, press [ 3. / ] to select the desired CTCSS/DCS encode and decode.Press 4. TX/DCS or SCAN to conrm and exit.Talk Around This function can be temporarily used in Channel mode. Once the radio is turned off or switched to another channel, the temporary setting will be erased and back to initial settings. By Talk Around function, you can directly communicate with other radios in your group in case the repeater is not activated or when you are out of the repeater range. The transceiver will transmit by RX frequency with its CTCSS/DCS signaling.In standby, press 1. FUNC, then press MINI key, LCD displays "TALK--OF".Press [ 2. / ] to select the desired setting. ON:Enable Talk Around OFF:Disable Talk AroundPress number key to conrm and exit.3. This function can be temporarily used in Channel mode. Once the radio is turned off or switched to another channel, the temporary setting will be erased and back to initial settings.Voice PromptThe prompting tone provides confirmation of entry, error status or malfunctions of the transceiver. You can enable or disable this function.In standby, press 1. FUNC, then press V/M , LCD displays "BEEP--XX".Press [ 2. / ] to turn on/off BEEP voice prompt. BEEP—OF: turn off voice prompt BEEP—ON: turn on voice promptPress number key to exit and store.3. Microphone Operation
309 LCD Backlight In standby status, press 1. FUNC , then press MINI LCD displays "LAMP-XX".Press [ 2. / ] to select desired backlight brightness(1-32 levels).Press number keys to conrm and exit.3. Microphone Operation
3110This function is mainly use for simple anti-theft alarm device in vehicles. When the transceiver be removed in an improper manner, the transceiver will emit and transmit alarming and background voice to system and other transceiver of the same frequency.Steering-wheel etc.Alarm cable [QL-01(B)]DC power cableBatteryAlarm cable [QL-01(A)]Long-distance Anti-theft Alarm Connect DC power cable with car battery.Connect the optional alarm cable QL-01(A) to the data jack on 1. the front panel as shown. Secure the other end of the cable to an object that stays xed in vehicle. (Note: if alarm cable QL-01 (A) is not enough long, you can choose optional alarm cable QL-01 (B) to extend).When transceiver power off by press 2. PWR key, the long-distance anti-theft alarm enable.When the alarm cable QL-01(A) or QL-01(B) is removed from the 3. DATA jack or cut by improper sequence, the alarm function enable and will alarm as programmed. In alarming, the transceiver will stop alarm once receiving a matching signal. And alarm again when a matching signal disappeared.Restart radio to cancel anti-theft alarming.Reconnect with alarm 4. cable and turn off radio, the system will return to alarm mode.The long-distance anti-theft alarm only available when transceiver power off.-LENNAHU-VO LPWRFUNCV/MCALLMHzTX/DCSH/LSCANMINI
3211This feature will copy the programmed data and parameters in the master unit to slave units. It copies the parameters and memory program settings.Use optional CP50 cloning cable, connect the cable between the data jacks on both master and slave.1. Press and hold 2. FUNC key, then press key to enter into cloning mode, LCD displays "CLONE".Press master unit's [PTT] key, LCD displays "3. SD XXX", "XXX" indicates data volume in transmitting. Slave unit displays "LD XXX", "XXX" indicates received data volume. When the transmission is successfully nished, the master and slave unit both display "PASS". Turn off the power, disconnect the cable and repeat step 2 to step 3 operations to clone the next slave unit.Cable CloneIf the data is not successfully transmitted, turn off both units, make sure the cable connection is correct and repeat the entire operation from the beginning.GND DATA TX/RXMaster/Slave stereo plug,3.5mm plugCALLPWRFUN CV/MC A LLMHzTX/DCSS C ANMI N I-LENNAHU-VO LPWRFUN CV/MC A LLMHzTX/DCSS C ANMI N I-LENNAHU-VO LCAL CAL
3312Programming Software Installing and Starting (in windows XP system)Double click "QPS598 setup.exe", then follow the installing instruction.This software has product identify system, so when rstly installing the software, you have to connect the products, otherwise you can not start the software. Install USB Cable Driver Programme(As pic 1)(As pic 2)(As pic 3)Click start menu in computer, under "ALL PROGRAMS" menu, 1. choose and click "USB To Com port" in QPS598 program, install "USB To Com port" driver by indication.Connect the optional PC50 USB Programming cable to USB port in 2. PC with transceiver.(As pic 1)Double click QPS598 shortcut or click QPS598 in procedure index 3. of start menu, choose serial com port as indicated then click OK to start programming software. (As pic 2)According to instruction, select correct "COM Port"(As pic 3), then 4. click "OK" to start programming software.Note:Even in same computer, the selective COM Port is different when USB cable connects with different USB port.You shall install software before connecting the USB cable line. Switch on transceiver before writing frequency. You had better not switch on or off the power supply of transceiver when it is connected with computer, otherwise, it will make transceiver unable to read or write frequency. In this case, you have to turn off programming software, pull out USB cable.then reinsert USB cable and open software, then rechoose COM Port, it will turn into normal operation. Therefore, please connect transceiver with computer after switching on the transceiver. Don't restart transceiver power when it is connected with computer.-LENNAHU-VO LPWRFUNCV/MCALLMHzTX/DCSH/LSCANMINI
3413AT598 DCS encode and decode -VFO frequency 145.00MHz DCS code 023NMemory channel 0-199 - Output power HIOffset direction - Key-lock setting OFFOffset frequency 600KHz TOT OFFChannel step 12.5KHz APO OFFCTCSS encode and decode - Squelch Level 4CTCSS frequency 88.5HzDefault Setting after Resetting(VHF) Trouble ShootingProblem Possible Causes and Potential Solutions(a) Power is on, nothing appears on Display.+ and - polarities of power connection are reversed. Connect red lead to plus terminal and black lead to minus terminal of DC power supply.(b) Fuse is blown. Check and solve problem resulting in blown fuse and replace fuse with new fuse.(c) Display is too dim. Dimmer setting is "LAMP-L". Please make the dimmer setting "LAMP-H".(d) No sound comes from speaker. • Squelch is muted. Decrease squelch level.• Tone or CTCSS/DCS squelch is active. Turn CTCSS or DCS squelch off.(e) Key and Dial do not function.Key-lock function is activated. Cancel Key-lock function.(i) Rotating Dial will not change memory channel.Transceiver is in CALL mode. Press the VFO or memory mode.(g) PTT key is pressed but transmission does not occur.• Microphone connection is poor. Connect microphone properly. • Antenna connection is poor. Connect antenna properly.Maintenance
3514Specications are subject to change without notice due to advancements in technology.GeneralFrequency RangeNumber of Channels200 channels Channel SpacingPhase-locked Step5KHz, 6.25KHz, 8.33KHz, 10KHz, 12.5KHz, Operating Voltage 13.8V DC ±15%SquelchCarrier/CTCSS/DCS/5Tone/2Tone/DTMFFrequency Stability ±2.5ppmOperating Temperature-20℃~+60℃Dimensions(WxHxD) 145 (W) x 47 (H) x 190 (L)mmWeight about 1.2KgReceiver (ETSI EN 300 086 standard testing )Sensitivity(12dB Sinad) ≤0.35μVAdjacent ChannelSelectivity ≥60dBIntermodulation ≥60dBSpurious Rejection ≥70dBAudio Response +1~-3dB(0.3~2.55KHz)Hum & Noise ≥40dBAudio distortion ≤5% Audio power output ＞2W@10%Transmitter (ETSI EN 300 086 standard testing )Power Output 75WModulation 11KΦF3EAdjacent Channel Power ≥60dBHum & Noise ≥36dBSpurious Emission ≥60dBAudio Response +1~-3dB(0.3~2.55KHz)Audio Distortion ≤5%SpecificationsVHF: 136-174MHz 12.5K bandband
361567.0 79.7 94.8 110.9 131.8 156.7 171.3 186.2 203.5 229.169.3 82.5 97.4 114.8 136.5 159.8 173.8 189.9 206.5 233.671.9 85.4 100.0 118.8 141.3 162.2 177.3 192.8 210.7 241.874.4 88.5 103.5 123.0 146.2 165.5 179.9 196.6 218.1 250.377.0 91.5 107.2 127.3 151.4 167.9 183.5 199.5 225.7 254.1Attached Chart50 groups CTCSS Tone Frequency(Hz) 1024 groups DCS Code.000 001 002 003 004 005 006 007010 011 012 013 014 015 016 017020 021 022 023 024 025 026 027030 031 032 033 034 035 036 037040 041 042 043 044 045 046 047050 051 052 053 054 055 056 057060 061 062 063 064 065 066 067070 071 072 073 074 075 076 077100 101 102 103 104 105 106 107110 111 112 113 114 115 116 117120 121 122 123 124 125 126 127130 131 132 133 134 135 136 137140 141 142 143 144 145 146 147150 151 152 153 154 155 156 157160 161 162 163 164 165 166 167170 171 172 173 174 175 176 177200 201 202 203 204 205 206 207210 211 212 213 214 215 216 217220 221 222 223 224 225 226 227230 231 232 233 234 235 236 237240 241 242 243 244 245 246 247250 251 252 253 254 255 256 257260 261 262 263 264 265 266 267270 271 272 273 274 275 276 277300 301 302 303 304 305 306 307310 311 312 313 314 315 316 317
3715320 321 322 323 324 325 326 327330 331 332 333 334 335 336 337340 341 342 343 344 345 346 347350 351 352 353 354 355 356 357360 361 362 363 364 365 366 367370 371 372 373 374 375 376 377400 401 402 403 404 405 406 407410 411 412 413 414 415 416 417420 421 422 423 424 425 426 427430 431 432 433 434 435 436 437440 441 442 443 444 445 446 447450 451 452 453 454 455 456 457460 461 462 463 464 465 466 467470 471 472 473 474 475 476 477500 501 502 503 504 505 506 507510 511 512 513 514 515 516 517520 521 522 523 524 525 526 527530 531 532 533 534 535 536 537540 541 542 543 544 545 546 547550 551 552 553 554 555 556 557560 561 562 563 564 565 566 567570 571 572 573 574 575 576 577600 601 602 603 604 605 606 607610 611 612 613 614 615 616 617620 621 622 623 624 625 626 627630 631 632 633 634 635 636 637640 641 642 643 644 645 646 647650 651 652 653 654 655 656 657660 661 662 663 664 665 666 667670 671 672 673 674 675 676 677700 701 702 703 704 705 706 707710 711 712 713 714 715 716 717720 721 722 723 724 725 726 727730 731 732 733 734 735 736 737740 741 742 743 744 745 746 747750 751 752 753 754 755 756 757760 761 762 763 764 765 766 767770 771 772 773 774 775 776 777N is positive code, I is negative code, total: 232groups.Attached Chart
00cmSAFETYTRAININGINFORMATIONYour    radiogeneratorsRFelectromagneticenergyduringtransmitmode.Thisradioisdesignedforandclassifiedas“OccupationalUseOnly”,meaningitmustbeusedonlyduringthecourseofemploymentbyindividualsawareofthehazards,andthewaysToMinimizeSuchhazards.ThisradioisNOTintendedforusebythe“GeneralPopulation”inanuncontrolledenvironment.ThisradiohasbeentestedandcomplieswiththeFCCRFexposurelimitsfor“OccupationalUseOnly”.Inaddition,your   radiocomplieswiththefollowingStandardsandGuidelineswithregardtoRFenergyandelectromagneticenergylevelsandevaluationofsuchlevelsforexposuretohumans: �to Radio Frequency Electromagnetic Fields. �American National Standards Institute (C95.1-1992), IEEE Standard for Safety Levels with Respect to Human Exposure to Radio Frequency Electromagnetic Fields, 3 kHz to 300 GHz. �American National Standards Institute (C95.3-1992), IEEE Recommended Practice for the Measurement of Potentially Hazardous Electromagnetic Fields– RF and Microwave. �The following accessories are authorized for use with this product. Use of accessories other than those (listed in the instruction) specified may result in RF exposure levels exceed the FCC requirements for wireless RF exposure. Toensureyou’reyourexposetoRFelectromagneticenergyiswithintheFCCallowablelimitsforoccupationaluse,alwaysadheretothefollowingguidelinesTheinformationlistedaboveprovidestheuserwiththeinformationneededtomakehimorherawareofRFexposure,andwhattodotoas‐surethatthisradiooperateswiththeFCCRFexposurelimitsofthisradio.ElectromagneticInterference/CompatibilityDuringtransmissions,    radiogeneratesRFenergythatcanpossiblycauseinterferencewithotherdevicesorsystems.Toavoidsuchinterference,turnofftheradioinareaswheresignsarepostedtodoso.DONOToperatethetransmitterinareasthataresensitivetoelectromagneticradiationsuchashospitals,aircraft,andblastingsites.Occupational/ControlledUseTheradiotransmitterisusedinsituationsinwhichpersonsareexposedasconsequenceoftheiremploymentprovidedthosepersonsarefullyawareofthepotentialforexposureandcanexercisecontrolovertheirexposure.InordertocomplywithRFexposurerequirements,aminimumdistanceof mustbemaintainedbetweentheantennaandallpersonsFCC OET Bulletin 65 Edition 97-01 Supplement C, Evaluating Compliance with FCC Guidelines for Human Exposure 2Qixiang Electron Science & Technology Co.,Ltd.Qixiang Electron Science & Technology Co.,Ltd.Qixiang Electron Science & Technology Co.,Ltd.

Navigation menu