Qiyue Optronics QLM17XXXXXX 17” LCD Monitor User Manual
Shenzhen Qiyue Optronics Company Limited 17 LCD Monitor
User Manual
Color TFT LCD Monitor User's Manual Important Notice: Please read this manual carefully. Precaution Read all of these instructions and save this manual for later use. Follow all warnings and instructions on the product. 1. Do not cover or block the ventilation holes in the case. 2. Do not insert sharp objects or spill liquid into the LCD monitor through the cabinet slots; this may cause accidental fire, electric shock or failure. 3. Unplug the unit when not in use for an extended period of time. 4. Do not attempt to service this product yourself, as opening or removing the cover may expose you to potential electric shock. Only a qualified technician should service this product. 5. Do not touch the screen directly with your fingers as it may damage the screen; the oil from your skin is difficult to remove. 6. Do not apply pressure to the screen, the LCD is very delicate. 7. Keep the monitor away from extreme heat, cold or humid places. 8. Do not place directly under sunlight, dusty surroundings or near equipment, which may generate strong magnetic fields. CAUTION: TO REDUCE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. FCC Notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help. Note: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment Introduction Product Description Thank you for choosing the Flat Panel TFT-LCD Color Monitor. It combines the features of a MONITOR with a THIN FILM TRANSISTOR Liquid crystal display (TFT-LCD). This new generation of TFT-LCD incorporates a high quality display in a lightweight module. Unlike CRT displays, the LCD panel has a fixed format over a set area. So. for best performance the "native resolution" setting is recommended. For 17" wide screen LCD monitors: The native resolution of LCD panel is 1440 x 900. Recommenden resolution is 1440 x 900@60Hz. Package Contents Please check the TFT-LCD Monitor Package to make sure it contains the following tiems: Power cord VGA cable TFT LCD Monitor Color TFT LCD Monitor User's Manual DVI cable Important Notice: Please read this manual carefully. Audio cable User's Manual Menu Operating Instructions Your LCD monitor allows you to easily adjust the characteristics of the image being displayed. All of these adjustments are made using the control buttons on the front bottom of the monitor. While you use these buttons to adjust the controls, the OSD (On Screen Display) shows you their numberic values as they change. Instructions of each button on the LCD monitor, please see Menu Control Buttons on the next page. Direct Access Features 1. Push "AUTO" to get the optimal image. 2. With the OSD off, push the "MENU" button to display the main OSD menu. 3. Use " +/- " buttons to select the function, and press the "MENU" button once to activate the selected function. 4. After selecting a function, use the " +/- " buttons to make necessary addjustments. The setting bar moves and the numberic value indicator changes to reflect your adjustments. 5. Select the "Exit" icon to return to the main menu to select another function or to exit from the OSD. The new settings will be automatically saved. You can also press "MENU" button repeatedly to go backward to upper-level menu or exit the OSD. 6. When OSD is not active or visible on your screen: push " - " to decrease volume. push " + " to increase volume. 7. You can choose input source in OSD menu (see OSD function instructions). Menu Control Buttons LED AUTO MENU AUTO : Automatically adjusts for an optimal image (when no OSD is used). Returns to upper level of OSD, or exits the main menu (when OSD is used). MENU: Displays the main menu, or selects command function. : Decreases value. When OSD is not active or visible on the screen, push " - " to decrease volume. : Increases value. When OSD is not active or visible on the screen, push " + " to increase volume. : Power on/off control. LED : Power On: Green. Power Saving or No Signal: Red. On Screen Display (OSD) Functions Instruction 1. Color Menu It enables you to adjust image Color. OSD ther Color Contrast 50 - Picture Brightness 50 - Function Color Temp OSD Menu Color Adjust Misc Exit 9300 6500 User Exit Contrast To adjust image contrast. Brightness To adjust image brightness. Color Temp To set the Color temperature: 9300, 6500, User. Color Adjust To enter Color Adjust submenu. You can adjust Color components Red, Green and Blue manually. OSD ther Color Red 100 - Picture Green 100 - Function Blue 100 - OSD Menu Exit Misc Exit After adjusting, choose Exit or press AUTO repeatedly to exit. 2. Picture Menu It enables you to adjust picture. OSD ther Color H.Position 50 - Picture V.Position 50 - Function Phase 73 - OSD Menu Clock 50 - Misc Sharpness Exit Exit 1 2 3 4 5 H.Position To adjust horizontal position of picture. V.Position To adjust vertical position of picture. Phase To adjust the phase of picture. Clock To adjust the clock of picture. Sharpness To adjust the sharpness of picture: from level 1 to 5. After adjusting, choose Exit or press AUTO repeatedly to exit. 3. Function Menu It enables you to use Auto Adjust and Auto Color function. OSD ther Color Auto Adjust YES NO Picture Auto Color YES NO Function Exit OSD Menu Misc Exit Auto Adjust To do auto picture adjusting. Auto Color To do auto Color adjusting. After adjusting, choose Exit or press AUTO repeatedly to exit. 4. OSD Menu It enables you to adjust OSD menu properties. Color Language Picture Exit Function OSD ther OSD Menu Misc Exit Language Select Language to enter language setting submenu (see below). OSD ther Color English Italiano Picture Francais 繁體中文 Function Deutsch 简体中文 OSD Menu Espanol 日本语 Misc 한국어 Portugues Exit Use "+", "-" buttons to choose the language you need. After adjusting, choose Exit or press AUTO repeatedly to exit. 5. Misc Menu It enables you to choose input source, do reset, etc. OSD ther Color Input Picture Reset Function Volume OSD Menu Exit YES NO 50 - Misc Exit Input To select input source: VGA, DVI (see below). Color OSD ther VGA Picture DVI Function Exit OSD Menu Misc Exit Reset To reset all the settings to factory default. Volume To adjust the volume. After adjusting, choose Exit or press AUTO repeatedly to exit. Display Modes For 17" Wide Mode Mode Resolution 10 11 12 13 14 15 16 17 18 720 x 400 720 x 400 640 x 480 640 x 480 640 x 480 800 x 600 800 x 600 800 x 600 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1280 x 1024 1280 x 1024 1280 x 768 1280 x 768 1440 x 900 1440 x 900 Vertical Frequency (Refresh Rate) 60Hz 70Hz 60Hz 72Hz 75Hz 60Hz 72Hz 75Hz 60Hz 70Hz 72Hz 75Hz 60Hz 75Hz 60Hz 75Hz 60Hz 75Hz To set the display mode 1. Set the resolution: Right dick on the Windows® desktop → choose Propeties → choose Settings → set the resolution. 2. Set the refresh rate: See your graphic card's user guide for instructions. 10 Connection to PC 1. Please connect to the 100–240V AC socket. 2. Please connect signal cable to the PC. 11 Specification Item Display Size Active Area Maximum Resolution Pixel Pitch Aspect Ratio Display Colors Description 17" wide 367(H) x 229(V) mm 1440 x 900 0.255 mm 16:10 262,144 Brightness (Typ.) Contrast Ratio Response Time View Angle Vertical Frequency Display Mode 200cd/m 600:1 16ms 45+45(H)/20+45(V) 60Hz~75Hz VGA, SVGA, XGA, SXGA, WXGA+ Signal Interface D-Sub (Analog), DVI-D (Digital) Power Consumption <25W (Operation) Power Consumption <1W (Saving) Power Supply 100-240 V AC, 50/60Hz OSD Language Multi-language Speaker 2W x 2 Operation Environment Temperature 0ć-50ć, Humidity 20%-80% Store Temperature 20ć-60ć, Humidity 20%-80% Notice:Environment Specifications are to change without noticing the customer. 12 Cleaning 1. Gently wipe the screen with a clean, soft, lens brush or a soft clean, lint-free cloth. This removes dust and other particles that can scratch the screen. 2. Do not apply pressure to the screen surface when wiping it clean. 3. Do not pour or spray any liquid directly onto the screen or case of the LCD monitor. Chemical cleaners may damage the screen of LCD monitor. Troubleshooting LCD pixel statement The LCD unit is produced with high-precision manufacturing techniques. Nevertheless, some pixels may occasionally misfire or appear as black or colored dots. This has no effect on the recorded image and does not constitute a malfunction. Normally, a 17" WXGA+ (1440 x 900) display has nearly 4 million subpixels. There are 8 non-performing pixels on the LCD screen, which is only 0.0002@ of the total sub-pixels. This percentage is acceptable for any inspection specifications. • There is no picture on the screen. A: Please check the color of the LED indicatior on the LCD monitor. 1. "GREEN": During normal operation the LED light will be green. If it is green and there is no picture, contact the customer service line. 2. "RED": Please check the connection of the VGA cable to the monitor and the connection to the computer. 3. "NO POWER": Make sure the power cord is securely connected to the socket. • Missing Colors A: If any of the red, green, or blue colors are missing, check the signal cable to make sure it is tightened correctly. the pins in the cable could be loose and cause a bad connection. • No Image A: 1. Make sure power button is ON. 2. Check whether the LCD monitor and computer power cords are connected and whether there is a supply of power. • No Signal Input A: Please check the signal connection between the computer and LCD monitor. 13 • Image too bright / too dark A: Adjust brightness and contrast by OSD. • Irregular Image A: 1. Check the signal connection between the computer and LCD monitor. 2. Perform Auto Adjust. • Distorted Image A: Reset the LCD monitor (Perform "Reset" function by OSD). • Image is not centered / Size is not appropriate. A: 1. Use OSD Picture Menu to adjust H.Position and V.Position. 2. Check image size setting. 3. Perform Auto Adjust. • No sound. A: 1. Check the audio signal cable connection between the computer and LCD monitor. 2. Check the volume setting. 14
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.3 Linearized : No Page Count : 15 XMP Toolkit : XMP toolkit 2.9.1-13, framework 1.6 About : uuid:99c74672-7d80-41b4-9bcb-c5b981ad0576 Producer : Adobe PDF Library 8.0 Trapped : False Create Date : 2009:09:18 14:31:26+08:00 Modify Date : 2009:09:18 14:34:20+08:00 Metadata Date : 2009:09:18 14:34:20+08:00 Creator Tool : Adobe InDesign CS3 (5.0.1) Thumbnail Format : JPEG Thumbnail Width : 188 Thumbnail Height : 256 Thumbnail Image : (Binary data 14684 bytes, use -b option to extract) Instance ID : uuid:17b02cd9-020d-4135-843e-c26e9324d045 Rendition Class : proof:pdf Document ID : adobe:docid:indd:689797a4-861d-11de-ad2b-a1922a231a6a Manifest Link Form : ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream Manifest Placed X Resolution : 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00 Manifest Placed Y Resolution : 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00 Manifest Placed Resolution Unit : Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches Manifest Reference Instance ID : uuid:64e6e0de-07df-4f9c-bbb3-780b870ea0c8, uuid:488d9e80-c8b4-4409-9a5c-5e7256086ccf, uuid:82606774-9aab-443e-a201-94403757b8f6, uuid:d661c6bc-e92f-4c3e-ba57-3ee4b77b1fa0, uuid:49324dba-5c21-453e-80ef-5b00a0347a60, uuid:573a670d-3647-44ee-9da9-a03b6c2a2127, uuid:a6ebb657-bf0f-4c2d-bdf7-9bcfb967ce51, uuid:ab5358fa-1e47-46f0-bd25-b2ea0809f3d8, uuid:06514f57-4134-459f-9c51-1485c4f75822, uuid:da3a1739-d8ee-403a-89ab-18695f9a2942, uuid:631d593e-e7d5-4472-858f-eb3b4a3a3376, uuid:38c4a6de-aa0c-4584-aa6e-7a1d752d8201, uuid:235ada29-8b3b-4754-bf06-0c377d4fad17, uuid:ed5995c0-8a11-4daa-9662-606c3bfd62cb, uuid:94570679-5b06-43f8-aabf-69e6cbf2fba8, uuid:92bc1122-55e9-430c-8b95-82c26537a8a7, uuid:e4e93967-6642-4ff0-af90-badf38e9fdaa, uuid:a9d97c7b-398e-47ff-8d83-263bef19b192 Manifest Reference Document ID : uuid:84af4950-b857-4433-ac75-81ca36b6f5fc, uuid:f8c51bfa-0f8f-4cfa-aedf-6286aed6af97, uuid:90d18ea6-ab0d-4ca6-a9f6-8fca4ace1c87, uuid:90d18ea6-ab0d-4ca6-a9f6-8fca4ace1c87, uuid:aa17ea88-446c-4825-bb4e-d8f15685d0ad, uuid:df7d32c2-e7f7-45e7-9415-ec825b978728, uuid:e6f9c3bb-bf8f-4e8c-8555-4a3420768dc0, uuid:731f8cc5-49c9-4a91-ad3c-ed1b8aa6f9c9, uuid:ad7fd0d0-bb50-4c79-a622-e8d883af7ceb, uuid:b10ab32d-b7b3-4f5c-8e1a-7f9591e5407f, uuid:94174df7-dfc7-4199-a5c0-a01e6840f56f, uuid:ca773707-b293-4352-b3c5-f2694ec38747, uuid:05a264bb-9b93-4419-b708-294bdc6e4a74, uuid:d51c1727-cb6d-4a31-812c-de432044f3ec, uuid:ecd4b3b8-8ca1-4160-9cc7-bd83c99d67a5 Format : application/pdf Creator : Adobe InDesign CS3 (5.0.1)EXIF Metadata provided by EXIF.tools