Quad Bit System QR1356-UL4 13.56MHz RF-ID Reader User Manual

Quad Bit System Co., Ltd. 13.56MHz RF-ID Reader

User Manual

RFID MANUALQR1356-UM4/UL4
How to Telnet SetupConnect to PC• The MUX and PC (NMP) to change settingsusing the LAN Cable 1: 1 connection box.• Executes the DOS Command Prompt• Telnet IP port number Input• Press the Enter Key, the screen transitionDOS PromptNotebook
Output Setting• QbSeXiT input, being converted into setupmode• To change the output settings, enter the ‘2’• For PM4 Do not operate because 1W fixed.• When the setting input screen display, changethe value and press Enter Key, changed.• Is now 2W, If you want to change to 4W, ’40’should enter05 : 0.5W10 : 1W15 : 1.5W20 : 2W25 : 2.5W…80 : 8W • If you enter anything dBg does not appear in the screen, detect screen being displayed.How to Telnet Setup
Scan Time Setting• Enter the value you want to change15 : 0.15초50 : 0.5초100 : 1초• If you want to change the scan level, pressingthe ‘4’• If you enter an invalid value, you may not beable to read.• After setting value input pressing Enter Key450 : 250 ~ 650 Scan Range500 : 300 ~ 700 Scan Range550 : 350 ~ 750 Scan Range600 : 400 ~ 800 Scan Range• If you want to change the scan time, pressingthe ‘3’.사용방법 -스캔레벨How to Telnet Setup
• You need the IP settings as beside figure.• LAN Cable should be connected betweenthe Notebook(PC) and the Reader.• The connection may not want if the wirelessnetwork is turned on.• Should be checked, as shown below.• Executing a DOS command.• Red underline two check file.• Conversion to the Reader update mode.• Executing a batch file.• Normally about 10-20 seconds Wait.• Reader of the power OFF / ON.• Use the tweezers into the smallhole next to the LAN cable, switch the mode to update the reader.• Run LED is blinking faster display.• When the update mode, indicatedby a red LED blinking only• After completion, LED display inthe normal modePC Setting and F/W Update
How to Modify IPLAN Setting① LAN Settings in theControl Panel② Click Properties inthe Local Area③ Click Properties ofIP / V4④ Insert the IP address210.210.210.10⑤ Fixed default gateway.However, if the MUXis factory reset / firmware update status.192.168.0.10③⑤②④①
EtherIO-V Scan for QBS 실행① Double-click on the desktop icon② Double Click ‘SCAN’③ Click Select Device④ Double Click• The program is provided separately. Ensure personnel are needed.③②④①How to Modify IP
IP modification of EtherIO-V Scan for QBS① Query Click② >> Click③ IP Confirm④ IP Modify⑤ Write Click③⑤②④①How to Modify IP
RFID User ManualCAUTION : Changes or modifications not expressly approved by theparty responsible for compliance could void the user’s authority to operate the equipment.NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:- Reorient or relocate the receiving antenna.- Increase the separation between the equipment and receiver.- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.- Consult the dealer or an experienced radio/TV technician for help.
Think You
DECLARATION OF CONFORMITY According to FCC Part 15 Applicant Name : Quad Bit System Co., Ltd. Address : 402, 217 Heojun-Ro, Gangseo-Gu, Seoul, Korea Telephone : +82-2-3665-8088 Declares that Product : 13.56MHz RF-ID Reader Model Name : QR1356-UL4 Report Number : CTK-2014-01502 This device complies with Part 15 of the FCC rules. Operations is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Test Laboratory: CTK Co., Ltd. (Ho-dong), 113, Yejik-ro, Cheoin-gu, Yongin-si, Gyeonggi-do, 449-100, Korea Designation Number : 805871 Tel : +82-31-339-9970 Fax : +82-31-624-9501 Responsible Party: Company Name : Quad Bit System Co., Ltd. Company Address : 402, 217 Heojun-Ro, Gangseo-Gu, Seoul, Korea Phone : +82-2-3665-8088 Fax : +82-2-3665-8096 Name : Kim Chang Dong Signature :

Navigation menu