Quad Bit System QR1356-UL4 13.56MHz RF-ID Reader User Manual
Quad Bit System Co., Ltd. 13.56MHz RF-ID Reader
User Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 2470080 |
| Application ID | QMC1ch8p3J0DjGA8iXrxuw== |
| Document Description | User Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 211.68kB (2645998 bits) |
| Date Submitted | 2014-12-11 00:00:00 |
| Date Available | 2014-12-11 00:00:00 |
| Creation Date | 2014-12-11 03:00:31 |
| Producing Software | doPDF Ver 7.3 Build 382 (Windows 7 Home Premium Edition (SP 1) - Version: 6.1.7601 (x64)) |
| Document Lastmod | 2014-12-11 07:32:22 |
| Document Title | User Manual |
RFID MANUAL QR1356-UM4/UL4 How to Telnet Setup Connect to PC • The MUX and PC (NMP) to change settings using the LAN Cable 1: 1 connection box. Notebook DOS Prompt • Executes the DOS Command Prompt • Telnet IP port number Input • Press the Enter Key, the screen transition How to Telnet Setup Output Setting • If you enter anything dBg does not appear in the screen, detect screen being displayed. • QbSeXiT input, being converted into setup mode • To change the output settings, enter the ‘2’ • For PM4 Do not operate because 1W fixed. • When the setting input screen display, change the value and press Enter Key, changed. • Is now 2W, If you want to change to 4W, ’40’ should enter 05 : 0.5W 10 : 1W 15 : 1.5W 20 : 2W 25 : 2.5W … 80 : 8W How to Telnet Setup Scan Time Setting • If you want to change the scan time, pressing the ‘3’. • Enter the value you want to change 15 : 0.15초 50 : 0.5초 100 : 1초 사용방법 - 스캔레벨 • If you want to change the scan level, pressing the ‘4’ • If you enter an invalid value, you may not be able to read. • After setting value input pressing Enter Key 450 : 250 ~ 650 Scan Range 500 : 300 ~ 700 Scan Range 550 : 350 ~ 750 Scan Range 600 : 400 ~ 800 Scan Range PC Setting and F/W Update • You need the IP settings as beside figure. • LAN Cable should be connected between the Notebook(PC) and the Reader. • The connection may not want if the wireless network is turned on. • Should be checked, as shown below. • • • • • • Executing a DOS command. Red underline two check file. Conversion to the Reader update mode. Executing a batch file. Normally about 10-20 seconds Wait. Reader of the power OFF / ON. • Use the tweezers into the small hole next to the LAN cable, switch the mode to update the reader. • Run LED is blinking faster display. • When the update mode, indicated by a red LED blinking only • After completion, LED display in the normal mode How to Modify IP LAN Setting ① ① LAN Settings in the Control Panel ② Click Properties in the Local Area ② ③ ③ Click Properties of IP / V4 ④ Insert the IP address 210.210.210.10 ④ ⑤ Fixed default gateway. However, if the MUX is factory reset / firmware update status. 192.168.0.10 ⑤ How to Modify IP EtherIO-V Scan for QBS 실행 • The program is provided separately. Ensure personnel are needed. ① Double-click on the desktop icon ① ② Double Click ‘SCAN’ ② ③ Click Select Device ③ ④ Double Click ④ How to Modify IP IP modification of EtherIO-V Scan for QBS ① Query Click ① ② >> Click ③ IP Confirm ③ ② ④ IP Modify ④ ⑤ Write Click ⑤ RFID User Manual CAUTION : Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. Think You DECLARATION OF CONFORMITY According to FCC Part 15 Applicant Name : Quad Bit System Co., Ltd. Address : 402, 217 Heojun-Ro, Gangseo-Gu, Seoul, Korea Telephone : +82-2-3665-8088 Declares that Product : 13.56MHz RF-ID Reader Model Name : QR1356-UL4 Report Number : CTK-2014-01502 This device complies with Part 15 of the FCC rules. Operations is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Test Laboratory: CTK Co., Ltd. (Ho-dong), 113, Yejik-ro, Cheoin-gu, Yongin-si, Gyeonggi-do, 449-100, Korea Designation Number : 805871 Tel : +82-31-339-9970 Fax : +82-31-624-9501 Responsible Party: Company Name : Company Address : Quad Bit System Co., Ltd. 402, 217 Heojun-Ro, Gangseo-Gu, Seoul, Korea Phone : +82-2-3665-8088 Fax : +82-2-3665-8096 Name : Kim Chang Dong Signature :
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No Page Mode : UseNone XMP Toolkit : 3.1-701 Create Date : 2014:12:11 03:00:31+09:00 Modify Date : 2014:12:11 07:32:22+09:00 Metadata Date : 2014:12:11 07:32:22+09:00 Producer : doPDF Ver 7.3 Build 382 (Windows 7 Home Premium Edition (SP 1) - Version: 6.1.7601 (x64)) Format : application/pdf Document ID : uuid:f8766429-47e6-4b29-9602-ffad5ebf4db4 Instance ID : uuid:db88fbcc-1295-4176-8887-392910223fa0 Page Count : 11 Page Layout : OneColumnEXIF Metadata provided by EXIF.tools