Quantum Instruments QFTRIO Remote control of camera flash User Manual Trio instr 3 10 full page
Quantum Instruments Inc Remote control of camera flash Trio instr 3 10 full page
instructions
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 924393 |
| Application ID | iApXgpgb1LOy/OCqpy6yIA== |
| Document Description | instructions |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 46.87kB (585837 bits) |
| Date Submitted | 2008-04-07 00:00:00 |
| Date Available | 2008-10-06 00:00:00 |
| Creation Date | 2008-04-07 11:00:26 |
| Producing Software | Mac OS X 10.4.8 Quartz PDFContext |
| Document Lastmod | 2008-04-07 11:00:26 |
| Document Title | Microsoft Word - Trio instr 3-10 full page.doc.doc |
| Document Creator | Word |
| Document Author: | GME |
tested to comply with FCC standards CANADA : FCC ID: CEXQFTRIO Qflash Trio This device complies with Part 15 of the FCC Rules and with RSS-210 of Industry & Science Canada. Operation is subject to the following conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received including that which may cause undesired operation of the device Quantum® Qflash® “Trio” shoe mount Digital Flash Operating Instructions IMPORTANT – CAUTION Changes or modifications to this equipment could void your authority to use this product under the equipment authorization granted by the regulating agencies 0678 Declaration of Conformity: Quantum Instruments, Inc. declares that Qflash Trio satisfies all the technical regulations applicable to the product within the scope of Council Directive 1999/e/EC. Quantum Instruments Inc. 10 Commerce Drive, Hauppauge NY 11788-3968 USA Tel: 1-631-656-7400 Fax: 1-631-656-7410 www.qtm.com QUANTUM Q® Designed and manufactured in the USA Page 28 Page 1 Rev Date 3.06.08 Flash Display Symbols The top portion of the display contains information relating to the status of the internal radio, and the options that are set on the flash. See Section 8 for setting the radio and Section 9 for setting the options. Note : in some modes the radio mode will be set automatically. CH – Channel setting of internal radio, 0 through 7 Tx / Rx – Radio set as Transmitter (Tx) for SYNC / LINK / QTTL or Receiver (Rx) for RX 1234 – zones that are turned on. If a zone is off it will be replaced by a “-“ Speaker ON Reflector type N – normal, D – diffusor / wide angle dome / soft box, B – bare bulb reflector, T – telephoto Flash LED indicators ON Flash ready Flash compensation set CH 4 Tx 1234 QTTL F 5.6 FILL +0 FIRE ISO 200 OPT MOD /OK Page 2 SAVE RADIO SET Page 27 Table of Contents 1. Introduction 2. Warnings 3. Advanced Features Summary 4. Getting started 5. Basic Navigation 6. Basic Options 7. Choosing the right mode 8. Radio set up 9. Options 10. Q QTTL Mode 11. A Automatic Mode 12. QR QTTL Ratio Mode 13. M Manual Mode 14. RL Remote – Linked to local Qflash Mode 15. RA Remote Auto Wireless Mode 16. RG Remote Group mode 17. AM Advanced Multi Mode 18. PRGM Program mode 1. INTRODUCTION Quantum’s “Trio” series flash integrates camera dedication, Qflash quality light, and Quantum’s Free X Wire radio technology into a single shoe mount flash. The Trio is compatible with Qflash series 5d-R and 3d-R, and Free X Wire models FW10w, FW7Q, FW8R, FW9T. Many features of the Trio will enhance your lighting control when used with Qflash5d-R and Free X Wire FW10w, FW7Q, FW8R While powerful and extremely versatile, the operation of the Trio is intuitive and straightforward. Many of the wireless modes will set the Radio to Transmit (Tx) or Receive (Rx) automatically. We encourage you to start pushing buttons and explore the operation of the Trio. Older Qflash models can be upgraded to work with the new Trio. See www.qtm.com for costs for these upgrades. 2. WARNINGS Disconnect external power before changing the flash tube, connecting or disconnecting to/from cameras, power packs, or any other equipment. Operate only with a flash tube in the socket Do not touch the flash tube socket with metal objects This is a professional instrument. Keep away from children Do not attempt to open the flash unit! dangerous high voltage inside Page 26 Page 3 3. Advanced Features Summary The chart below summarizes the advanced features for various Qflash series. A “U” means the Qflash model will have this feature when upgraded to series 5d-R. An “F” means this feature is available in the model shown. An “N” means the feature is not available. Visit qtm.com for upgrade procedures and costs. Feature QF4d Qflash Models QF5d QF5d-R Trio Wireless Control in Nikon/Canon systems with Qnexus Wireless multiple ratio TTL (QF5d-R requires Dw-R Adapters & FreeXWire) Wireless preflash TTL with digital cameras (QFlash requires Dw/ Dw-R Adapters and FreeXWire) Wireless remote Auto / Auto Fill mode Zone control of FW7Q from panel of Qflash Flash ready indication in camera viewfinder Shutter speed control (camera detects flash and sets shutter) Rear Curtain Sync High speed sync Auto focus assist Auto Fill ratio 4.1 Restoring Factory settings 4. Getting Started You can restore the factory settings by the following method: 1. 2. 3. 4. Turn Turbo OFF, connect Trio to Turbo. Press and hold any button Turn Turbo ON. The Qflash will display a reset message and some soft key options RESET ALL - will restore all the factory settings. KEEP P1 P8 - will keep your stored Program modes, but reset everything else to factory settings. EXIT – will exit the reset menu without changes 4.1 Inserting the Flash Tube Match the red dot on the base of the flash tube with the red dot in the socket of Qflash. Push the flash tube in until it is seated snugly into the socket. Excessive force is not required. Page 4 Page 25 Replace the flash tube only with Quantum type QF30 or QF30uv for Qflash model T5d / T5d-R. Qflash model X5d / X5d-R requires QF32 or QF32uv flash tubes. Other flash tubes will not provide proper exposure, may not work at all, or they may damage the Qflash. 4.2 Reflectors and Bare Bulb Reflectors are secured by the locking ring near the base of the reflector. Rotate the ring in the directions shown in the diagram to loosen or tighten the reflectors. LOCK When inserting a reflector, first slowly rotate it until the notch in the reflector “drops” fully into head of the Qflash. Then tighten the locking ring. If you do not let the reflector drop fully into the Qflash before locking it, the reflector may become loose during use. UNLOCK The “normal” QF60 reflector is supplied with Qflash 5d-R. Other reflectors are available as options from your dealer. Reflector Normal QF60 QF60 w/flat diffuser QF67A Dome diffuser QF 68 Soft Box QF69 Mini Soft Box QF62Bs/g Bare Bulb Reflector QF63B Tele Reflector Approx. Angle 55 70 90 Guide No. for ISO 200 QFT5d-R QFX5d-R 200 Ws 400 226ft / 72m 226ft / 72m 320ft / 128ft / 40m 128ft / 40m 180ft / 128ft / 40m 128ft / 40m 180ft / 120 90ft / 28m 90ft / 28m 128ft / 40m 20 453ft / 143m 453ft / 143m 640ft / 202m 4.3 Bounce and Swivel Head The head position is locked and can be changed with a single button (see diagram). Press and hold this button, then adjust the head to the desired position. Release the button, and slightly move the head until it “clicks” and locks the head into the vertical and horizontal planes. 4.4 Connecting Trio to a Camera Loosen Shoe lock until metal “foot” protrudes fully. Slide Trio into camera hot shoe. Tighten shoe lock wheel. Page 24 Page 5 RELEASE BUTTON Ws 100m 56m 56m 4.5 Powering Qflash Before turning on any power to Qflash always make all electrical connections first, both to the camera and to the power pack. The Trio is powered by any Quantum Turbo Battery including Turbo 2x2, Turbo Compact, Turbo SC, Turbo AC and Turbo Z. Plug the Trio power cable into the flash, then into the output connection of the power pack. If a “Check Turbo” message appears on the Trio display, turn off the Turbo, wait one second, and turn it on again. If the message appears again, the power pack needs recharging. Very Important Tips For consistent exposures with your digital camera and Trio. ! Always do a custom white balance before shooting ! When shooting TTL use Aperture or Shutter priority or Manual camera modes (P mode gives inconsistent exposures) ! Set your metering area to center weight, partial metering instead of matrix or multi-spot metering. ! Your Trio provides 90 watt-seconds of power compared to 50 watt-seconds of a typical shoe mount flash. When shooting 6 ft. (2m) or closer, at ISO 200 or greater, with a wide open F/#, you must always diffuse the light. Otherwise your subject will be over-exposed. 5. Basic Navigation This Section explains how to maneuver your way around the Trio The Left and Right buttons have two functions. 1. When a selection or setting is highlighted on the display the Left and Right buttons will change that selection or setting. For example if the F/number is highlighted then the Left and Right buttons will adjust the F/number up or down. 2. If there is nothing highlighted on the display the Left and Right buttons will change the function of the soft keys located under the display. The are four soft keys located at the bottom of the display. These soft keys will change function based on flash mode or user operation. MODE /OK SET The Mode button allows you to change the mode of the Trio. Pushing it will bring up the mode change menu. See Section 7 Choosing the right mode Page 6 The Set button will highlight the settings on the display. Each time you press the Set button it will cycle through the available settings. 6. Soft keys There are four soft keys located under the display. The function of these soft keys will change based on user operation. In some modes you can assign these soft keys to certain functions. 6.1 Soft key functions 6.1.1 Default assignment FIRE OPT SAVE (DEFAULT) RADI available for all Trio modes FIRE – Test fire the Trio, and any remotes if the radio is turned on OPT – Enter the options screen to change, speaker, indicator lights, reflector, etc. See section xx.x SAVE – Save this set up as one of the eight programs in PRGM MODE (Program Mode). See section xx.x RADIO – Enter radio set up menu to turn radio on/off, change zones and channels See section xx.x 6.1.2 Sensor limit 10 15-20 (SENSOR LIMIT) 6.1.3 Radio Zones 1 ON 2 ON 3 OFF (RADIO ZONES) OFF 4 OFF available for all Auto modes for all Trio modes when the radio is on, except for QTTL ratio and Advanced Multi modes. In these modes all zones default to ON. 6.1.4 Quick turn off only R1 R2 ON LOCA (QUICK TURN OFF) OFF Page 7 used in QTTL ratio and Advanced Multi 7. Choosing the right mode To select a mode, press the MODE/OK button. The available modes will appear across the top of the display, with the current mode highlighted. The full name of the current mode will also appear in the center of the display. Use the Left and Right arrow buttons to select the mode. Then press the MODE/OK or SET buttons to select the mode and exit. There are two soft keys in this menu, OFF and PRGM MODE QQ A QR M RL RA RG AM QTTL OFF PRG MOD MOD /OK SET OFF – This will prevent the flash from firing. Use this if you want to turn off the light from the on camera flash, but still want any remotes you are using to fire when the shutter is pressed. PRGM MODE - Pressing this button will bring you into the program mode. In the program mode you can store up to eight of your favorite settings. You can easily jump between any of these eight settings for quick lighting set ups. Below is a description of each mode and it’s operation. This will aid you in choosing the mode that is best for the desired lighting . 7.1 Q QTTL QTTL mode uses the exposure system built into the camera. You may offset exposure by 2 stops above or 3 stops below camera setting. Use this mode if you want the camera to control the exposure Radio: Can be set to send a SYNC signal to fire remote flashes. Each remote flash controls it’s own exposure. Or it can be set to send a QTTL signal to remote Qflashes. Positives : Simplest of all the QTTL mode while still being able to fire and/or control remote flashes, such as power packs used for room lights Negatives : Not possible to ratio remote flash exposures. Remotes will be the same exposure as the local flash. Page 8 7.2 A Automatic Light output is controlled by the sensor located on the front of the flash. When flash is placed on a camera F number and ISO information are sent to the flash from the camera. As the F number and ISO are changed on the camera this flash will follow. Use this mode if you want the sensor to control the exposure Radio: Can be set to send a SYNC signal to fire remote flashes. Each remote flash controls it’s own exposure. Or it can be set to send a LINK signal to both fire and control the exposure of remote Qflashes. Positives : Fast response for action shots. No pre flash required. Exposure easily checked with flash meter. Remote Qflash can be adjusted from –3 stops below to +2 stops above camera settings. Negatives : Requires some knowledge of how auto flash exposure works. One remote exposure setting for all remotes. 7.3 QR QTTL Ratio Uses the exposure system built into the camera. Possible to set independent ratios of multiple remote flashes. Use this mode if you want to set up lighting ratios that are controlled by the camera’s TTL system. Radio: Turned on automatically. Set only Channel/Zones to match. Positives : Allows for ratios between remote flashes without entering the more complex Advanced Multi mode. Set remote Qflash 8's to RG mode. Negatives : Slower response, not good for action shots. Data transmission occurring before, during, and after shot. Data transmission can interfere with other photographers in the area. 7.4 M Manual Light output is controlled by fixed power output of flash. When flash is placed on a camera F number and ISO information are sent to the flash from the camera. As the F number and ISO are changed on the camera this flash will follow. Use this mode if you want the most accurate and repeatable exposures possible Radio: Can be set to send a SYNC signal to fire remote flashes. Each remote flash controls it’s own exposure. Or it can be set to send a LINK signal to both fire and control the exposure of remote Qflashes. Page 9 Positives : Most accurate of all flash modes. Negatives : Requires some knowledge of exposures, distance, and the use of a flash meter. 7.5 RL Remote Linked to local Qflash Quick and easy set up remote Qflash Trio. Light output is controlled by the local flash. Use this mode as the simplest way to set up remote flash systems. If the local Qflash is in QTTL-W mode then the exposure will match the output of the local flash. If the local flash is in Auto, this Remote flash can be set 2 stops above or 3 stops below the local flash. This is achieved by adjusting the ‘LINKED” setting on the local Qflash. Radio: Turned on automatically. Set only Channel/Zones to match. Positives : Not difficult to set up, and works for all modes of the local flash. No time delay between shutter and flash. Negatives : Most basic type of multiple flash mode, and therefore does not lend itself to complicated ratios. There is only one exposure setting for all remotes. 7.6 RA Remote Automatic Light output is controlled by the sensor located on the front of the remote Qflash. F number and ISO information are sent to the flash from the camera. As the F number and ISO are changed on the camera this flash will follow. Use this mode if you want a remote flash to have the dedication of a TTL flash, but the simplicity of the automatic sensor. Radio: set Automatically. Positives : No pre flash required. Very Quick mode. No time delay between shutter and flash. None of the problems associated with TTL. Negatives : Since exposure is controlled by the sensor on flash, user needs to be mindful of camera placement. If the camera and flash are in widely different locations, the picture will not be properly exposed. 7.7 RG Remote Group Allows full control of Remote Qflashes whose mode is set on the control panel located on the local Qflash Trio. Use this mode if you plan on making frequent changes to the settings on the remote flash, such as mode, f number, and power Page 10 Radio: set Automatically. Positives : Greatest flexibility in flash set up without leaving camera position.. Multiple flashes in mixed modes possible. Negatives : Slower response, not good for action shots. Data transmission occurring before, during, and after shot. Data transmission can interfere with other photographers in the area. 7.8 AM Advanced Multi This mode allows the user to have full control over Three remote flash groups. There is no limit to how flashes can be set to any one group. Mode, F number, power, and even linking the exposure of a remote flash group can all be set from the push buttons on the local flash. Radio: Turned on automatically. Set only Channels/Zones to match. Positives : Possible to set up mixed mode lighting set ups and make changes without walking over to the remotes. Good mode to use if the remotes are inaccessible. Negatives : Slow to use, not good for action shots. Data transmission occurring before, during, and after shot. Data transmission can interfere with other photographers in the area. 8. Radio set up Press the RADIO soft key to enter the radio set up menu. To exit the set up menu press the MODE/OK or SET buttons. RADIO OFF The two soft keys located on the right side are used to adjust the channel up or down. The soft key labeled ZONES is used to turn the zones ON or OFF. The left most soft key is used to set up the mode of the radio. OFF – Radio off no signal sent. OFF OFF SYNC RX ZONE LINK MOD /OK CH.4 ↑ ↓ SET SYNC – Trio sends a sync only signal to remotes. A remote flash can be another Trio, any Qflash using an FW10w, FW8R, FW7Q or any studio strobe using an FW10w, FW8R. Tx will appear in upper left corner of display. RX – Trio will fire when local flash sends a sync signal. Local flash can also control exposure of Trio set to RX. Local flash can be a Trio, a Qflash 5d-R using an FW10w or FW9T, or a QTTL adapter with an FW9T. Rx will appear in upper left corner of display. LINK / QTTL – Trio will send a sync signal plus exposure control signals to Remotes. A remote flash can be another Trio or Qflash 5d-R using an FW10w or FW7Q. Tx will appear in upper left corner of display. For a group of flashes that will fire together, set all units to the same chanel. Within each channel you may set units to different zones. Use different zones when you wish to tunr off some, but not all the remote flashes. Page 11 9. Options Press the OPT (options) soft key to enter the options set up menu. To exit the set up menu press the MODE/OK or SET buttons Use the LEFT or RIGHT arrows to select the option you want to change. F/M RESET ↑ ↓ The two soft keys located on the right side are used to adjust the option that has been elected. The RESET soft key is used to reset the Trio to factory default settings. 9.1 MOD /OK SET Speaker You may want the speaker off for sensitive shooting, or turn it on for audible confirmation of flash exposure. 9.2 Lock Trio Turning this option on will lock out the buttons and prevent any accidental changing of settings. To unlock the Trio Press the outer two soft keys when prompted. 9.3 Flash indicators The green Flash Indicators on either side of the Trio give visual indication that a flash fired, weather the exposure was good, over, under, or no flash, indicating that the flash did not fire. You can enable or disable the lights. 9.4 Sync type F – Front curtain sync, R – Rear curtain sync, HSS – high speed sync 9.5 Reflector Setting the reflector type is important so that the displayed distance, guide number and f/# correspond to the reflector in use. The choices are NORM (for the reflector supplied with Qflash), DIFF (for diffusers supplied with Qflash, optional QF67A Dome diffuser, QF68 Soft Box, or QF69 Mini Soft Box), BBE (optional Bare Bulb Enhancers QF62Bs and QF62Bg) and TELE (for optional QF63B Tele photo reflector). The reflectors must be repositioned manually. Notes: When using QF62B s/g the manual parameters are accurate only for an open area. In medium and small rooms the very widely dispersed light will bounce off nearby walls and increase exposure. A practical solution when using QF62B in small rooms is to meter the light, or use Auto, TTL, or QTTL modes which will provide better exposures and attractive, soft lighting. When using a Telephoto Reflector QF63B the Auto mode cannot be used because the flash sensor is blocked. Use Manual, TTL, QTTL, Strobo or Linked modes. Page 12 9.6 Compensation Quantum calibrates Qflashes to American National Standards Institute (ANSI) standards with laboratory equipment traceable to the National Institute of Standards and Technology (NIST). From time to time, photographers may wish to fine tune Qflash exposures to match their exposure meters, to compensate for variations in cameras or films, to match particular styles, for effects, or for individual taste. There are two compensations available- one for Manual and one for Auto mode. In QTTL modes Qflash does not control exposure and compensation will not apply. “Compensation” affects overall exposure, not fill or ratio settings of various modes. 9.6.1 Manual mode Qflash Compensation This procedure will calibrate Qflash to an incident light flash meter you use and trust. Note that only incident light measurements are reliable for manual exposure settings. 1. Place the TRIO 10 feet from the incident light flash meter facing Qflash. 10 Ft Meter Qflash set to Manual mode Wall 2. The area surrounding the meter and flash should be similar to the shooting environment you usually work in. For example, in a large hall, there will be little light bouncing from walls and ceilings. In a small room, the light meter reading will be increased by whatever bounce occurs from nearby surfaces. These factors will affect calibration and should be considered. 3. Turn the Trio on, set mode to manual (M) and change the manual power setting to 1/8. 4. Set the film speed on the flash and the flash meter to the same value. 5. Change the F number on the flash until the distance shown in the display is 10 feet. 6. Fire the Trio. Note the F/number on the flash meter. 7. Press the OPT soft key, then use the Left and Right buttons to scroll through the options until the manual compensation is highlighted. 8. Using the UP and DOWN soft keys, adjust the F/ number in the display until it matches the F/ number from the flash meter. 9.6.2 Auto mode Qflash Compensation This procedure will calibrate Qflash to a reflected light flash meter you use and trust. Note that only reflected light measurements are reliable for auto exposure settings. Page 13 This is because auto mode flashes read reflected light from the scene and subject. In order to compare those readings to a meter, the meter must also be reading the same reflected light. The reflected light is affected by the subject and background, and an incident light reading will not typically provide the same reading (unless the subject is an 18% gray card). 1. Place the Qflash 10 feet from a blank wall. The wall should be larger than the metering area of the meter, and preferably a wall of continuous tone (blank wall). 2. Place flash meter next to Qflash, also facing the blank wall. Be sure to set the flash meter for a reflected reading. Meter 10 Ft Qflash set to Auto mode Wall 3. Turn the Trio on, set the mode to Auto (A) and change the f/ number to F8.0 4. Set the film speed on the flash and the flash meter to the same value. 5. Fire the Trio. Note the F/number on the flash meter. 6. Press the OPT soft key, then use the Left and Right buttons to scroll through the options until the auto compensation is highlighted. 7. Using the UP and DOWN soft keys, adjust the F/ number in the display until it matches the F/ number from the flash meter. Page 14 10. Q QTTL Mode Operation F/number, ISO are sent to the flash from the camera. Only the fill setting is user adjustable. Press the Set button to highlight the fill setting. Use the left and right arrow buttons to adjust the fill up or down. The fill setting is used to adjust the flash output from 3 stops below (-3) the camera setting to 2 stops (+2) above the camera setting. The fill can be adjusted in 1/3 steps. QTTL F 5.6 FILL +0 ISO 200 FIRE OPT RADI SET MOD /OK Using the Radio SAVE The internal radio can be used to trigger remote flashes, or room lights, set radio SYNC. Or the radio can be used to control the light output of remote Qflashes, set radio QTTL. The remote flash can be another Trio in RL mode or a Qflash model 5d-R set to Linked to Local with an FW10w, FW7Q or FW8R. Be sure that the channel and zones match the channel and zones set on the Trio See section 8.0 for setting the channel and zones on the Trio 10.1 QTTL mode soft keys OPT SAVE (DEFAULT) If the radio is turned off, there is only the default soft key functions available FIRE If the radio is on, then the soft keys may be used to turn the radio zones on / off 1 ON RADI 2 ON 3 OFF (RADIO ZONES) 4 OFF 11. A Automatic Mode Operation 11.1 On camera Automatic mode AUTO F/number, ISO are sent to the flash from the camera. Only the fill setting is user adjustable. Press the Set button to highlight the fill setting. Use the left and right arrow buttons to adjust the fill up or down. The fill setting is used to adjust the flash output from 3 stops below (-3) the camera setting to 2 stops (+2) above the camera setting. The fill can be adjusted in 1/3 steps. F 5.6 FILL +0 3.6 – 32 FT FIRE OPT MOD /OK ISO 200 SAVE RADI SET Flash distance displays the working distance between your Qflash and Subject based on the current settings. Moving outside this range may result in an Under or Overexposed picture. Page 15 Using the Radio The internal radio can be used to trigger remote flashes, or room lights, set radio to SYNC. Or the radio can be used to control the light output of remote Qflashes, set radio to LINK. The remote flash can be another Trio in RL mode or a Qflash model 5d-R set to Linked to Local with an FW10w, FW7Q or FW8R. Be sure that the channel and zones match the channel and zones set on the Trio. See section 8.0 for setting the channel and zones on the Trio 11.2 Off Camera Automatic mode In the off camear operation the Fill adjust will be disabled, however the F/number, ISO are user adjustable. Pressing the Set button will highlight them in that order. Use the left and right arrow buttons to adjust the highlighted setting up or down. AUTO F 5.6 7 3.6 – 32 FT FIRE OPT ISO 200 SAVE RADI Using the Radio SET To enable the Trio to be fired remotely set the MOD internal radio to RX. An FW10w or FW9T must be /OKcamera position. located at the camera position, or you can use another Trio at the Be sure that the channel and zones match the channel and zones set on the Trio. See section 8.0 for setting the channel and zones on the Trio 11.3 Auto mode soft keys To change the function of the soft keys use the Left and Right buttons when no selection or setting is highlighted on the display. If the radio is turned off, the default and sensor limit soft key functions available FIRE OPT SAVE (DEFAULT) RADI If the radio is on, then the soft keys may be used to turn the radio zones on / off 10 15-20 (SENSOR LIMIT) 1 ON OFF 2 ON 3 OFF (RADIO ZONES) 4 OFF 11.4 Auto mode exposure indications There are three types of exposure indications. The display will blink either OK, Over, or Undr. The display will also indicate how much over or under the last exposure was, from +3 stops to 3 stops. If an arrow appears then the exposure error is more than 3 stops (for example -3 ). If activated in Options (Section 8.2) the Speaker will sound after a flash. The audible signal is one “beep” for “OK and ready”, and three “beeps” for “Undr” or “Over”. Page 16 11.4 Auto Sensor Limit Setting Qflash to Auto exposure makes picture taking fast and easy. However, an automatic flash has a flaw: the sensor on the flash expects the subject to be wide, flat, and fill the view of the sensor. A person standing against a wall fits this description; people in a catering hall or in a park at night do not. When the background is located far behind the subject, the automatic flash struggles to produce even lighting. The result is often an over exposed subject, sometimes by as much as two stops. When a photo lab develops film with a greatly over exposed subject, it will ‘print down’ to bring the flesh tones back into range. Or, time will be spent adjusting a digital image, with the resultant loss of detail and image quality. To solve this problem use the Flash sensor limit. ∞ - No limit placed on sensor distance 20ft / 6m, 15ft / 4m, 10ft / 3m, 5ft / 2m, When the Flash Sensor Limit is set to ∞ the flash will produce the desired f/# for a subject within the flash’s minimum and maximum flash distance. With Auto Sensor Limit turned on, a ‘Limit’ indicator is activated. After a flash, if the subject’s distance exceeds the sensor limit currently set (5, 10, 15 or 20ft. / 2, 3, 4, 6m) the word ‘Limit’ will appear in the display. Three beeps and/or 3 blink warning may also occur (if those features are set in Options). If the subject is within the current sensor limit normal exposure indicators (OK, Undr, Over) will apply. 11.6 Using the Sensor Limit The flash Sensor Limit function essentially cuts down on the distance that Qflash attempts to illuminate. See the examples shown below. Open field The subject is located 15 feet from the camera. The background is an open field in a park. By setting the Sensor Limit to 15 feet, the flash will read only the light from subjects within 15 feet, ignoring anything further. Page 17 Two subjects separated by a gap Sometimes two subjects are separated by a gap. When this occurs the sensor is ‘looking’ between the two subjects and may miss them. The Sensor Limit will correct for this by reading only the light from objects within the limit set, in this case, 15 feet. The light from objects further away will be ignored. With the Sensor Limit it is no longer necessary for the subject to be centered in the frame. As long as the subject is within the Sensor Limit 12. QR QTTL Ratio Mode Operation F/number, ISO are sent to the flash from the camera. Local fill setting (on camera flash), R1 ratio, and R2 ratio are user adjustable. Pressing the Set button will highlight them in that order. Use the left and right arrow buttons to adjust the highlighted setting up or down. When you Press the Set button, an ON/OFF soft key will appear on the right of the display. You can use this soft key to prevent the Local, R1 or R2 flashes from firing. QTTLWR FILL +0 F 5.6 R1 +1 R2 -1 ISO 200 FIRE OPT MOD /OK SAVE RADI SET To prevent a flash from firing, press the Set button until the flash you want to turn off is highlighted. Then press the OFF soft key, the word “OFF” will appear next to that flash. Using the Radio The internal radio will be turned on automatically, but you may still need to select the proper channel to match the channel on the Remote flashes. See section 8.0 for setting the channel and zones on the Trio The remote flashes may be a Trio or a Qflash model 5d-R with a FW7Q or FW8R. If the remote flash is another Trio then it must be set to RG remote group mode. If the remote is a model 5d-R, select either Wireless Remote Group R1 or Wireless Remote Group R2. Page 18 12.1 QTTL Ratio mode soft keys Only the default soft key functions are available FIRE OPT SAVE (DEFAULT) RADI In the QTTL Ratio mode the radio is set automatically and all zones are ON 13. M Manual Mode Operation 13.1 On camera Manual Mode F/number, ISO are sent to the flash from the camera. Only the power setting is user adjustable. Press the Set button to highlight the power setting. Use the Left and Right arrow buttons to adjust the power up or down. Power settings are adjustable in 1/3 steps from full power to 1/64th power like this: 1/1, 1/1-, 1/2+, 1/2 ,1/2- …… 1/32. MAN GN 55 F 5.6 7 ISO 200 32 FT FIRE OPT MOD /OK SAVE RADI SET Using the Radio The internal radio can be used to trigger remote flashes, or room lights, set radio to SYNC. Or the radio can be used to control the light output of remote Qflashes, set radio to LINK. The remote flash can be another Trio in RL mode or a Qflash model 5d-R set to Linked to Local with an FW10w, FW7Q or FW8R Be sure that the channel and zones match the channel and zones set on the Trio. See section 8.0 for setting the channel and zones on the Trio 13.2 Off camera Manual Mode In the off camear operation Power, F/number, ISO are all user adjustable. Pressing the Set button will highlight them in that order. Use the left and right arrow buttons to adjust the highlighted setting up or down. Using the Radio To enable the Trio to be fired remotely set the internal radio to RX. A FW10w or FW9T must be located at the camera position, or you can use another Trio at the camera position. Be sure that the channel and zones match the channel and zones set on the Trio. See section 8.0 for setting the channel and zones on the Trio 13.3 Manual mode soft keys To change the function of the soft keys use the Left and Right buttons when no selection or setting is highlighted on the display. Page 19 If the radio is turned off, there is only the default soft key functions available If the radio is on, then the soft keys may be used to turn the radio zones on / off OPT FIRE SAVE (DEFAULT) 1 ON 2 ON 3 OFF (RADIO ZONES) RADI 4 OFF 13.4 Manual shooting made easy Nothing can beat the combination of a flash meter and a flash set manually. Automatic and TTL are a compromise based on the need for speed. Setting the flash for a manual power setting and taking an incident meter reading takes time and resources the average photographer may not have. So we use automatic flash exposure and know that in some situations the sensor may be fooled. The Trio allows for easy manual shooting without metering. Below is an example of how this is accomplished. In this example Qflash will produce an F8.0 at the subject (8 ft), and it Will be quickly accomplished without metering. The F number and Film speed will come from your camera, adjust the power setting until the Qflash distance shown matches the subject distance as closely as possible. 14. RL Remote – linked to local Qflash Mode Operation Light output of this flash will equal the light output of the local, the local flash can be set to any mode. The Local flash maybe a Trio, a Qflash model 5d-R with a FW10w or FW9T. Or you may use a QTTL adapter with an FW9T for wireless TTL with no local flash. Using the Radio REMOTE – LINKED TO LOCAL QFLASH FIRE OPT MOD /OK SAVE RADI SET The internal radio will be turned on automatically, but you may still need to select the proper channel to match the channel on the Remote flashes. See section 8.0 for setting the channel and zones on the Trio. The local flash may be a Trio in any mode, the radio of the local Trio must be set to LINK or QTTL. The local flash may also be a Qflash5d-R in any mode with an FW10w or FW9T. The TTL feature / switch must be turned on, see your FW instructions for turning the TTL feature on. Or the local flash may be a QTTL adapter with an FW9T. Page 20 14.1 Remote – linked to local Qflash soft keys To change the function of the soft keys use the Left and Right buttons when no selection or setting is highlighted on the display. Both the default and radio zones soft key functions are available OPT FIRE SAVE (DEFAULT) 1 ON RADI 2 ON 3 OFF 4 OFF (RADIO ZONES) 15. RA Remote Auto Wireless Mode Operation F/number, and ISO sent from the local flash. The Local flash maybe a Trio, a Qflash model 5d-R and QTTL adapter with a FW10w or FW9T. Or you may use a QTTL adapter with an FW9T for remote auto with no local flash. REMOTE AUTO W F 5.6 7 ISO 200 3.6 – 32 FT FIRE OPT SAVE RADI Using the Radio SET The internal radio will be turned on automatically, MOD but you may still need to select the proper channel /OKsetting the channel and zones to match the channel on the Remote flashes. See section 8.0 for on the Trio. The local flash may be a Trio in any mode, the radio of the local Trio must be set to LINK or QTTL. The local flash may also be a Qflash5d-R in any mode with an FW10w or FW9T. The TTL feature / switch must be turned on, see your FW instructions for turning the TTL feature on. Or the local flash may be a QTTL adapter with an FW9T. 15.1 Remote Auto Wireless soft keys To change the function of the soft keys use the Left and Right buttons when no selection or setting is highlighted on the display. The default, radio zones and sensor limit soft key functions are available . FIRE OPT SAVE (DEFAULT) 1 ON RADI 10 15-20 (SENSOR LIMIT) 2 ON 3 OFF (RADIO ZONES) OFF 15.2 Remote Auto Wireless exposure indicators and sensor limit The exposure indicators and sensor limit function the same as they do in Auto mode. See section xx.x Page 21 4 OFF 16. RG Remote Group Mode Operation When using this mode the Local flash must be REMOTE GROUP R1 a Trio, or a Qflash model 5d-R with an FW10w or FW9T. On the remote Trio the display will prompt you to select one of three possible groups. AUTO F 5.6 7 3.6 – 32 FT ISO 200 FIRE OPT SAVE RADI Group L – Remote flashes set to this group will SET MOD have the same exposure as the local flash, the local flash can be set to any mode. /OK Remote-linked to local Qflash will appear on the display if this group is selected Group R1 / R2 – The operation of remotes set to this group depend on the mode of the local flash. Using the Radio The radio is set automatically and the function of the remote Trio depends on the settings of the local Qflash. You may still need to select the proper channel to match the channel on the local Qflashes. See section 8.0 for setting the channel and zones on the Trio. If the local Qflash is a Trio set to advanced multi (AM) or a 5d-R set to Wireless Control, then mode, power, F/number and ISO for the remote Trio is set on the display of the local flash. If the local Qflash is set to QTTLwR (Trio or 5d-R) then the remote Trio will automatically be set QTTL ratio. The ratio adjustments for Groups R1 and R2 would be done on the display of the local flash. If the local Qflash (Trio or 5d-R) is set to any other mode, then the remote Trio set to Group R1 and R2 would default to Linked to local Qflash, and produce the same exposure as the local flash. 16.1 Changing the Remote Group If after selecting the Group you wish to change it, press the Set button and the Group will highlight. Use the Left and Right buttons to scroll through the Remote Group choices or use the Remote Group soft keys that appear. 16.2 Remote Group soft keys To change the function of the soft keys use the Left and Right buttons when no selection or setting is highlighted on the display. Only the default soft key functions are available FIRE OPT SAVE (DEFAULT) RADI In the Remote Group mode the radio is set automatically and all zones are ON Page 22 17. AM Advanced Multi Mode Operation This mode gives full control of the Mode and all the settings of the Local flash plus two remote flash groups. ADV. MULTI ISO 200 LOCAL MAN 1/8 R1 AUTO F 5.67 R2 AUTO F 8.03 Press the Set button until you reach the setting that you want to change is highlighted. Then use the Left and Right buttons to adjust the highlighted setting up or down FIRE When the Set button is pressed, the soft keys allow you to “jump” to a setting without having to scroll through all the settings. OPT SAVE RADI SET MOD /OK Using the Radio In Advanced Multi mode the radio is set automatically and all zones are ON. You may still need to select the proper channel to match the channel on the Remote flashes. See section 8.0 for setting the channel and zones on the Trio. The Remote flashes can be another Trio or a Qflash model 5d-R with an FW10w, FW8R, or FW7Q. The Remote flash must be set to one of the three following groups, Group L, Group R1, or Group R2. 17.1 Advanced Multi mode soft keys To change the function of the soft keys use the Left and Right buttons when no selection or setting is highlighted on the display. FIRE The default soft key functions are available OPT SAVE (DEFAULT) RADI R1 R2 ON LOCA (QUICK TURN OFF) OFF The soft keys can also be used to quickly turn off the Local flash or any of the remote groups To turn off any group first press the soft key for that Group, then press the ON / OFF soft key. When the group has been turned off, the word OFF will appear next to that group. If the local flash is set to Auto then the sensor limit functions are available 10 15-20 (SENSOR LIMIT) Page 23 OFF 18. Program Mode Operation The Program mode allows you to store your favorite settings and set-ups and then quickly recall them just by pressing the soft keys. You can program up to 8 Qflash set-ups of Manual, Auto, or TTL operation, including settings for all parameters. 18.1 Saving a set up When you find a set up you like and want to store it, press the SAVE soft key. The display will prompt you to determine the program number (Pnumber) that you want to save the set up as. Use the Left and right arrows to adjust the P number up or down. Once you’ve selected the P number you want to store the set up as, then press the save soft key. If you wish to not save the set up, then press the exit soft key. 18.2 Using the program mode. To enter the program mode, press the MODE button, then press the PRGM MODE soft key, then press the MODE button again. The current program number will be displayed along with the mode and the settings for that program. The soft keys allow you to change to a different program number quickly. You can change the function of the soft keys by pressing the Left and right arrows when nothing is highlighted. P1 QTTL F 5.6 FILL +0 ISO 200 P1-P2 P3-P4 P5-P6 P7-P8 MOD /OK SET The available soft key functions depend on the mode of the program. Any changes made to the settings of any program are saved to that program automatically. There is no need to take any action to save the changes. To exit the program press the MODE button, then use the left and right arrows to select a new mode, then press the MODE button again. Page 24
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf Linearized : No Page Count : 24 PDF Version : 1.4 Author : GME Creator : Word Create Date : 2008:04:07 11:00:26-04:00 Modify Date : 2008:04:07 11:00:26-04:00 Producer : Mac OS X 10.4.8 Quartz PDFContext Title : Microsoft Word - Trio instr 3-10 full page.doc.docEXIF Metadata provided by EXIF.tools