Quectel Wireless Solutions 201607EC25V LTE Module User Manual

Rugged Handheld Computer

- PA730 -

User's Manual

Version 1.1

unitech is a registered trademark of unitech Electronics Co., Ltd.

Revision History

Date Change Description Version

2017/9/26 first published version 1.0

2017/10/13 Update photos

Update spec info.

1.1

Preface

About This Manual

Thank you for purchasing the unitech product.

This manual explains how to install, operate and maintain our product.

No part of this publication may be reproduced or used in any form, or by any

electrical or mechanical means, such as photocopying, recording, or

information storage and retrieval systems, without permission in writing from

the manufacturer. The material in this manual is subject to change without

notice.

Regulatory Compliance Statements

FCC Warning Statement

unitech is a registered trademark of unitech Electronics Co., Ltd.

This device has been tested and found to comply with the limits for a Class B

digital device, pursuant to part 15 of the FCC rules. These limits are designed

to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may

cause harmful interference with radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference with radio or television reception,

which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following

measures:

unitech is a registered trademark of unitech Electronics Co., Ltd.

–Reorient or relocate the receiving antenna.

–Increase the separation between the equipment and receiver.

–Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

–Consult the dealer or an experienced radio/TV technician for help.

1. This transmitter must not be co-located or operating in conjunction with

any other antenna or transmitter.

2. This device complies with FCC RF radiation exposure limits set forth for

an uncontrolled environment. To maintain compliance with FCC RF

exposure requirements, avoid direct contact to the transmitting antenna

during transmitting.

3. Any changes or modifications (including the antennas) made to this device

that are not expressly approved by the manufacturer may void the user’s

authority to operate the equipment.

Operation on the 5.15 - 5.25GHz frequency band is restricted to indoor use

only. The FCC requires indoor use for the 5.15-5.25GHz band to reduce the

potential for harmful interference to co-channel Mobile Satellite Systems.

Therefore, it will only transmit on the 5.25-5.35 GHz, 5.47-5.725 GHz and

5.725–5.850 GHz band when associated with an access point (AP).

FCC Label Statement

This device complies with part 15 of the FCC rules. Operation is subject to the

following two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including interference

that may cause undesired operation.

unitech is a registered trademark of unitech Electronics Co., Ltd.

Hearing Aid Compatibility Information

The FCC has adopted hearing aid compatibility (HAC) rules for digital wireless

phones. These rules require certain phones to be tested and rated under the

American National Standard Institute (ANSI) C63.19-2007 or C63.19-2011

hearing aid compatibility standards.

The ANSI standard for hearing aid compatibility contains the below rating:

An “ M “ rating for reduced radio frequency interference to enable acoustic

coupling with hearing aids that are not operating in telecoil mode.

These rating are given on a scale form one to four, where four is the most

compatible. A phone is considered hearing aid compatible under FCC rules if it

is rated M4 for acoustic coupling.

Hearing aid compatibility ratings don't guarantee that a particular hearing aid

works with a particular phone. Some hearing aids might work well with phones

that don’t meet particular ratings. To ensure interoperability between a hearing

aid and a phone, try using them together before purchase.

This phone has been tested and rated for use with hearing aids for some of the

wireless technologies it uses. However, there may be some newer wireless

technologies used in this phone that have not been tested yet for use with

hearing aids. It is important to try the different features of this phone thoroughly

and in different locations, using your hearing aid or cochlear implant, to

determine id you hear any interfering noise. Consult your carrier or Unitech for

information on hearing aid compatibility. If you have questions about return or

exchange policies, consult your carrier or phone retailer.

RF Radiation Exposure Statement

For body contact during operation, this device has been tested and meets FCC

RF exposure guidelines when used with an accessory that contains no metal

and that positions the handset a minimum of 1 cm from the body.

Use of other accessories may not ensure compliance with FCC RF exposure

guidelines.

Canadian Compliance Statement

This Class B Digital apparatus meets all requirements of the Canadian

Interference-Causing Equipment Regulations.

Cet appareil numerique de la classe B respecte les exigences du Reglement

sur le material broilleur du Canada.

European Conformity Statement

unitech Electronics co., Ltd herewith declares that the unitech product is in

compliance with the essential requirements and all other provisions of the RED

2014/53/EU directive, the EMC 2014/30/EU directive and the Low Voltage

2014/35/EU directive.

The declaration of conformity is available for download at :

https://portal.unitech.eu/public/Safetyregulatorystatement

CE RF Exposure Compliance

This device meets EU requirements (2014/53/EU) on the limitation of exposure

of the general public to electromagnetic fields by way of health protection.

For body-worn operation, this device has been tested and meets the ICNIRP

guidelines and the European Standard EN 62209-2, for use with dedicated

accessories, SAR is measured with this device at a separation of 0.5 cm to the

body, while transmitting at the highest certified output power level in all

frequency bands of this device. Use of other accessories which contain metals

may not ensure compliance with ICNIRP exposure guidelines.

CE Mark Warning

This equipment complies with the requirements of Directive 2014/53/EU of the

European Parliament and Commission from 24 May, 2014 governing Radio

and Telecommunications Equipment and mutual recognition of conformity.

The highest CE SAR values for the device are as follows :

0.776 W/kg @ 10g (Head)

unitech is a registered trademark of unitech Electronics Co., Ltd.

1.400 W/kg @ 10g (Body)

RoHS Statement

This device conforms to RoHS (Restriction Of

Hazardous Substances) European Union regulations

that set maximum concentration limits on hazardous

materials used in electrical and electronic equipment.

Waste electrical and electronic equipment (WEEE)

unitech has set up a policy and process to meet the EU

directive 2002/96/EC and update 2003/108/EC

concerning electronic waste disposal.

For more detailed information of the electronic waste

disposal of the products you have purchased from

unitech directly or via unitech’s resellers, you shall either

contact your local supplier or visit us at :

https://portal.unitech.eu/public/WEEE

unitech is a registered trademark of unitech Electronics Co., Ltd.

Taiwan NCC Warning Statement

低功率電波輻射性電機管理辦法

第十二條：經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者

均不得擅自變更頻率、加大功率或變更原設計之特性及功能。

第十四條：低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有

干擾現象時，應立即停用，並改善至無干擾時方得繼續使用。

前項合法通信，指依電信法規定作業之無線電通信。

低功率射頻電機需忍受合法通信或工業、科學及醫療用電波輻射性電機設備

之干擾。

注意事項:

1. 使用過度恐傷害視力。

2. 使用30分鐘請休息10分鐘；2歲以下幼兒不看螢幕，2歲以上每天看螢幕不要超過

1小時。

3. 減少電磁波影響，請妥適使用。

Laser Information

The unitech product is certified in the U.S. to conform to the requirements of

DHHS/CDRH 21CFR Subchapter J and to the requirements of IEC 60825-1.

Class II and Class 2 products are not considered to be hazardous. The unitech

product contains internally a Visible Laser Diode (VLD) whose emissions do

not exceed the maximum limits as set forth in the above regulations. The

scanner is designed so that there is no human access to harmful laser light

during normal operation, user maintenance or prescribed service operations.

The laser safety warning label required by the DHHS/IEC for the unitech

product’s optional laser scanner module is located on the memory

compartment cover, on the back of the unit.

* Laser information only applies to the products with laser components.

CAUTION! Use of controls or adjustments or performance of procedures

other than those specified herein may result in hazardous laser

light. Use of optical instruments with the scanner, including

binoculars, microscopes, and magnifying glasses, with will

increase eye damage. This does not include eyeglasses worn by

the user.

LED Information

The unitech product contains LED indicator(s) or LED ring whose luminance is

not harmful to human eyes during normal operation, user maintenance or

prescribed service operations.

*LED information only applies to the products with LED components.

unitech is a registered trademark of unitech Electronics Co., Ltd.

Battery Notice

1. To guarantee optimal performance, it is recommended that rechargeable

batteries be replaced every year, or after 500 charging cycles are

completed. It is normal for the battery to balloon or expand after one

year or 500 cycles. Although it does not cause damage, it cannot be

used again and must be disposed of according to the location's safe

battery disposal procedures.

2. If a battery performance decreases more than 20%, the battery is at the

end of its life cycle. Stop use and ensure the battery is disposed of

properly.

3. The length of time that a battery lasts depends on the battery type and

how the device is used. Conserve the battery life by doing the following:

 Avoid fully uncharging the battery because this places additional

strain on it. Several partial uncharges with frequent charges are better

than a fully uncharged battery. Charging a partially charged battery

does not cause harm to the unit.

 Keep the battery cool. Avoid hot vehicles. For prolonged

storage, keep the battery at a 40% charge level.

 Do not leave the battery uncharged and unused for an extended

period of time, the battery will wear out and the longevity of the

battery will be at least half of one with frequent charges.

4. Protect battery life by not over or under charging the battery.

5. Please do not leave battery unused for long time without charging it.

Despite unitech’s safety precautions, the battery pack may begin to

change shape. If so, stop using it immediately. Please check to see if

you are using a proper power adapter to charge the battery or contact

your service provider for service.

6. If you cannot charge the battery after it has been idle for an extended

period of time and it begins to heat up, please do not try to charge it. It

may not be functional anymore.

7. Please only use the original battery from unitech. Using a third party

battery can damage our products. Please note that when such damage

occurs, it is not covered by unitech’s warranty policy.

unitech is a registered trademark of unitech Electronics Co., Ltd.

 RISK OF EXPLOSION IF BATTERY IS

REPLACED INCORRECTLY.

DISPOSE OF USED BATTERIES ACCORDING

TO THE INSTRUCTIONS.

 如果更換不正確之電池會有爆炸的風險

請依製造商說明書處理用過之電池

CAUTION!

 如果更换不正确之电池会有爆炸的风险

请依制造商说明书处理用过之电池

Battery charge notice

It is important to consider temperature when the battery pack is charging.

Charging is most efficient at normal room temperature or in a slightly cooler

environment. It is essential that batteries are charged within the stated range of

0°C to 40°C. Charging batteries outside of the specified range could damage

the batteries and shorten their life cycle.

CAUTION! Do not charge batteries at a temperature lower than 0°C. This will

make the batteries unstable and dangerous. Please use a battery

temperature detecting device for a charger to ensure a safe

charging temperature range.

CAUTION! To ensure the unit working properly, please keep all connectors

away from the contaminants staying inside of them such as dust,

grease, mud, and water. The negligence may cause the unit with

no communication, short circuited, overheated and so on.

CAUTION! If the connector is damaged, please ensure the connector is being

fully repaired before use the unit to avoid causing short circuited.

Storage and safety notice

Although charged batteries may be left unused for several months, their

capacity may be depleted due to build up of internal resistance. If this happens,

they will require recharging prior to use. Batteries may be stored at

temperatures between -20°C to 60°C, however they may deplete more rapidly

at higher temperatures. It is recommended to store batteries at room

temperature.

* The message above only applies to the usage of the removable batteries.

For the products with non-removable batteries / without batteries, please refer to

the specification of each product.

Product Operation and Storage Notice

The unitech product has applicable operation and storage temperature

conditions. Please follow the limitation of suggested temperature conditions to

avoid failure, damage or malfunction.

*For applicable temperature conditions, please refer to the specification of each

product.

Adapter Notice

1. Please do not leave the power adapter in the socket when it is not

connected to your unitech product for charging.

2. Please remove the power adapter when the battery is fully recharged.

3. The bundled power adapter that comes with your unitech product is not

meant to be used outdoors. An adapter exposed to water or rain, or a very

humid environment can cause damage to both the adapter and the

product.

4. Please only use the bundled power adapter or same specification of

adapter to charge your unitech product. Using the wrong power adapter

can damage your unitech product.

* The message above only applies to the product connected to the adapter.

For the products without using the adapters, please refer to the specification of

each product.

unitech is a registered trademark of unitech Electronics Co., Ltd.

Hearing Damage Warning

Zx.3 Warning

The warning shall be placed on the equipment, or on the packaging, or in the instruction

manual and shall consist of the following:

- the symbol of Figure 1 with a minimum height of 5 mm; and

- the following wording, or similar :

To prevent possible hearing damage, do not listen at high volume levels for long periods.

Alternatively, the entire warning may be given through the equipment display during use, when

the user is asked to acknowledge activation of the higher level.

unitech is a registered trademark of unitech Electronics Co., Ltd.

Worldwide Support

unitech’s professional support team is available to quickly answer questions or

assist with technical-related issues. Should an equipment problem occur,

please contact the nearest unitech regional service representative.

For complete contact information please visit the Web sites listed below:

Taipei, Taiwan – Headquarters Europe

Tel: +886-2-89121122 Tel: +31-13-4609292

E-mail: info@hq.ute.com E-mail: info@eu.ute.com

Address: 5F, No. 136, Lane 235, Baoqiao Road, Xindian

District, New Taipei City 231, Taiwan (R.O.C.)

Address: Kapitein Hatterasstraat 19, 5015 BB,

Tilburg, the Netherlands

xii

unitech is a registered trademark of unitech Electronics Co., Ltd.

Website: http://www.ute.com Website: http://eu.ute.com

China Japan

Tel: +86-59-2310-9966 Tel: +81-3-35232766

E-mail: info@cn.ute.com E-mail: info@jp.ute.com

Address:

Website:

Room401C, 4F, RIHUA International Mansion,

Xinfeng 3nd Road, Huoju Hi-tech District,

Xiamen, Fujan , China

http://cn.ute.com

Address:

Website:

Kayabacho Nagaoka Building 8F.,1-5-19

Shinkawa, Chuo-Ku,

Tokyo, 104-0033, Japan

http://jp.ute.com

Asia & Pacific / Middle East Latin America

Tel: +886-2-27911556 Tel: +52-55-5171-0528

E-mail: info@apac.ute.com

info@india.ute.com

info@mideast.ute.com

E-mail:

Address:

info@latin.ute.com

17171 Park Row, Suite 210

Houston, TX 77084USA (Rep.)

Address: 4F., No. 236, ShinHu 2nd Rd.,

NeiHu Chiu, 114, Taipei,Taiwan

Website: http://latin.ute.com

Website: http://apac.ute.com / http://mideast.ute.com

North America Please scan QR Code to visit us :

Tel: +1-714-8916400

E-mail:

Address:

Website:

info@us.ute.com / info@can.ute.com

6182 Katella Ave, Cypress, CA 90630, USA

http://us.ute.com

Warranty Policy

The following items covered under the unitech Limited Warranty are free from

defects during normal use:

The warranty period is varied from each country. Please consult with your

supplier or unitech local office for actual length of warranty period to your

purchased product.

Warranty becomes void if equipment is modified, improperly installed or used,

damaged by accident or neglect, or if any parts are improperly installed or

replaced by the user.

xiii

unitech is a registered trademark of unitech Electronics Co., Ltd.

Table of Contents

Preface.............................................................................................................i

Regulatory Compliance Statements ..............................................................i

Laser Information ......................................................................................... v

LED Information ........................................................................................... v

Battery Notice.............................................................................................. vi

Adapter Notice............................................................................................viii

Hearing Damage Warning........................................................................... ix

Worldwide Support..................................................................................... xii

Warranty Policy ..........................................................................................xiii

Chapter 1 - Overview................................................................................1

1.1 Package .................................................................................................1

1.2 Product Detail.........................................................................................2

1.3 Specifications .........................................................................................5

1.4 Getting Started .......................................................................................9

Chapter 2 – Installation & Operation.................................................14

2.1 Barcode Setting....................................................................................14

2.2 HF Setting ............................................................................................19

2.3 UHF Setting..........................................................................................20

2.4 MSR Setting .........................................................................................20

2.5 WWAN Setting......................................................................................21

2.6 WLAN Setting.......................................................................................23

2.7 PAN Setting..........................................................................................24

2.8 GPS Setting..........................................................................................25

2.9 PC Setting ............................................................................................27

2.10 Camera Setting ..................................................................................29

2.11 Performing a Hardware Reset ............................................................32

2.12 Performing Factory Data Reset..........................................................33

2.13 Programmable Keys...........................................................................34

xiv

unitech is a registered trademark of unitech Electronics Co., Ltd.

2.14 Battery Swap......................................................................................36

xv

unitech is a registered trademark of unitech Electronics Co., Ltd.

Chapter 3 – Introduction to Applications.........................................37

3.1 Scan Service ........................................................................................37

3.2 File Manager ........................................................................................40

3.3 Update Center......................................................................................41

3.4 Sound Recorder ...................................................................................42

3.5 Push To Talk .........................................................................................44

3.6 MoboLink..............................................................................................45

3.7 SOTI.....................................................................................................49

PA730 User’s Manual

Chapter 1 - Overview

1.1 Package

Please make sure the following contents are in the PA730 gift box.

If something is missing or damaged, please contact your unitech

representative.

The standard package contents

 PA730 Terminal

 Battery

 Hand Strap

 Quick Start Guide

 USB Cable (with two special ferrite cores )

 the special USB cable must be used with this device

 Power Adapter ( EU or US )

 Regulatory Compliance Statements

1

unitech is a registered trademark of unitech Electronics Co., Ltd.

PA730 User’s Manual

1.2 Product Detail

PA730 Front View

1Front camera 6Camera button

2Logo 7Speaker

3Back key 8Light sensor

4Home key 9LED

5Menu key

2

unitech is a registered trademark of unitech Electronics Co., Ltd.

PA730 User’s Manual

PA730 Rear View

3

unitech is a registered trademark of unitech Electronics Co., Ltd.

1 Battery pin 5 Hand strap hook

2 6 Back camera

SIM card slot

3 Micro SD card slot 7Flash LED

4 Battery cover lock switch

PA730 User’s Manual

PA730 Left and Right View

1 Ear phone jack 5 Scan button

2 Scan button 6 Volume up

3 Function Key 7 Volume down

4 Power button 8 USB connect

4

unitech is a registered trademark of unitech Electronics Co., Ltd.

PA730 User’s Manual

1.3 Specifications

System Features

Processor Qualcomm APQ8052(617) ARM A53 64 bits CPU

Quad Core*1.5Ghz &Quad Core*1.2Ghz

Memory 16GB eMMC Flash ROM plus 2GB LPDDR3 RAM

Expanded slot One user accessible Micro SD Memory Slot

One user accessible SIM slot

Display

5.0”, Color FHD

Capacitive type 5 points multi-touch touch panel with Gorilla Glass

Support finger, glove and stylus

FHD(full high definition):1920 x 1080 (1080P)

Brightness: 500cd/m2 (nits)

Transmissive type TFT LCD

Keypad

Front Key :Standard Android 3 keys(touch key together with touch panel) and one function key.

Side Key : Scan key left and right., volume key up and down, power key and function key.

Indicator

2 x LED indicators for charging LED & information LED.

One vibrator for scan or ring in indication

Audio tone indication

Engines

2D Imager engine (SE 4750)

1D All major codes

2D：PDF417, MicroPDF417, Composite, RSS,

TLC-39, Datamatrix, QR code, Micro QR code,

Aztec, MaxiCode, Postal Codes: US PostNet, US

Planet, UK Postal, Australian Postal, Japan Postal

Dutch Postal (KIX)

Audio

Dual speaker

One receiver and dual noise-cancelling microphones

3.5mm DIA stereo headset jack with MIC. In

5

unitech is a registered trademark of unitech Electronics Co., Ltd.

6

unitech is a registered trademark of unitech Electronics Co., Ltd.

PA730 User’s Manual

External Connector

One user accessible micro SD Memory slot with SDHC, SDXC compliance and software

image upgrade features

One user accessible Micro SIM slot

Micro USB (B type) support USB 2.0 OTG and USB charge

Cradle connector support USB 2.0 and DC power input

Software

MoboLink, SOTI

Regulatory Approvals

CE, FCC, RoHS compliance

￭ FCC certification :

Max 1g Reported Head SAR (W/kg) 0.46

Max 1g Reported Body SAR (W/kg) 0.39 Limit: 1.60 W/kg

Max Product specific 10g Reported

Body SAR (W/kg) 0.32 Limit: 4.00 W/kg

Max Reported 1g Simultaneous

Transmission SAR (W/kg) 0.97 Limit: 1.60 W/kg

Distance (mm) 10

Verdict PASS

Communication

USB USB 2.0 OTG

WLAN 802.11a/b/g/n/ac Wireless LAN, 2.4GHz and 5GHz

Compliant with WEP, WPA and IEEE 802.11i WPA2

Fast roaming under 100ms

Enterprise security

PAN Bluetooth 4.1 LE

Support profile : HID, A2DP, OPP, SPP

WWAN

(Option)

 Europe:

FDD LTE: B1/B3/B5/B7/B8/B20

TDD LTE: B38/B40/B41

WCDMA: B1/B5/B8

GSM: 900/1800

 North America-Verizon

FDD LTE: B4/B13

GPS GPS/GLONASS (Only for WAN model)

PA730 User’s Manual

NFC ISO14443-4 (Type A, Type B), ISO15693

Mifare, Felica(ISO/IEC18092)

Camera and Flash Light

NFC location is on the

battery cover.

Rear camera: 16M pixels CMOS color camera with autofocus

Front camera: 5.0M pixels CMOS color camera

LED flash light with torch

Sensors

Accelerometer, Light sensor, Proximity sensor

Gyroscope, E-compass

Power Source

Battery Replaceable Main Battery : 3.7V, typ. 2960mAh Li-Ion

battery pack(standard), typ. 5920mAh (extended)

One rechargeable RTC backup battery

One rechargeable backup battery for battery swap

Power Adapter 100~240Vac, 50/60Hz Input

5V, 2A / 9V, 2A output

Enclosure

Weight Approximately 340g with standard battery

Dimension Approximately 158 X 77 X 16.9 mm

Environmental

Operating temperature -4°F to 122°F (-20°C to 50°C)

Storage temperature -22°F to 140°F (-30°C to 60°C) (without Battery)

10% ~ 90% ( non-condensing )

Relative Humidity

1.8m MIL-STD 810G

Drop test to Concrete

Environmental Sealing IP67 & IP65 standard

ESD +/-8KV direct discharge, +/-15KV air discharge

Tumble 0.5m tumbles for 300 cycles and 600 drops

Operating System

Android 6.0

7

unitech is a registered trademark of unitech Electronics Co., Ltd.

8

unitech is a registered trademark of unitech Electronics Co., Ltd.

PA730 User’s Manual

Radio Type Description Frequency Maximum Output

Bluetooth

BR+EDR 2400~2483.5 MHz 4dBm

Bluetooth Bluetooth

4.0-LE 2400~2483.5 MHz 4dBm

2.4GHz 2400~2483.5 MHz 17dBm

5150~5350 MHz 21dBm

WLAN

5GHz 5470~5725 MHz 22dBm

GSM 900 880~915 MHz 33dBm

GSM GSM 1800 1710~1785 MHz 30.5dBm

WCDMA

Band I 1920~1980 MHz 24dBm

WCDMA WCDMA

Band VIII 880~915 MHz 24dBm

LTE Band 1 1920~1980 MHz 23.5dBm

LTE Band 3 1710~1785 MHz 23dBm

LTE Band 5 824MHz~849MHz 23dBm

LTE Band 7 2500~2570 MHz 23dBm

LTE Band 8 880~915 MHz 23dBm

LTE Band 20 832~862 MHz 23dBm

LTE Band 38 2570~2620 MHz 23dBm

LTE Band 40 2300~2400 MHz 23dBm

LTE

LTE Band 41 2496MHz~2690MHz 23dBm

NFC 13.56 MHz

Other GPS 1575.42 MHz

NOTE : Requirements in

AT/BE/BG/CZ/DK/EE/FR/DE/IS/IE/IT/EL/ES/CY/LV/LI/LT/LU/HU/MT/NL/NO/PL/PT/RO/

SI/SK/TR/FI/SE/CH/UK/HR. 5150MHz~5350MHz is for indoor use only.

9

unitech is a registered trademark of unitech Electronics Co., Ltd.

PA730 User’s Manual

1.4 Getting Started

1.4.1 Installing The Battery

1. Press and push the hand hook to loosen or move the hand strap

from PA730.

2. Push up the battery cover switch to unlock, and remove battery

cover from top.

PA730 User’s Manual

3. Insert the battery pack, and the put back the battery cover.

4. Push down the battery cover switch to lock the cover.

NOTE: After installing the battery, make sure the battery cover is securely closed, or you may

be unable to turn ON the terminal.

WARNING! There is a risk of fire and burns if the battery pack is handled improperly. DO

NOT disassemble, crush, puncture, short external contacts, or dispose the

battery pack in fire or water. DO NOT attempt to open or service the battery pack.

Dispose of used batteries according to local recycling guidelines in your area.

10

unitech is a registered trademark of unitech Electronics Co., Ltd.

PA730 User’s Manual

1.4.2 Charging The Battery

Before you turn on and start using this device, it is recommended that you

charge the battery.

If the battery has been discharged for several days, you may need to charge

for several minutes before powering it on.

Use only the adapter and the USB cable that came with this device to charge

the battery. When the battery power is too low, make sure to use the power

adapter or put into the dock to charge, not the USB cable connection with your

computer.

￭ Charge with USB

￭ Charge with cradle

11

unitech is a registered trademark of unitech Electronics Co., Ltd.

PA730 User’s Manual

1.4.3 Turning On The Terminal For The First time

After you have initially charged your device for about 24 hours, the device is

ready to be used. You can now start up your device. You can then set up the

languages, WiFi setting, and date and time.

Power-On Button

Turn ON your device by pressing the power button of the terminal.

1.4.4 Checking The LED Status

Status LED Description

Blue light Message received

Message Blue light Miss called

12

unitech is a registered trademark of unitech Electronics Co., Ltd.

Red light Being charged

Terminal

Green light Fully charged

Power

Orange light Quick charged

Checking the battery status

If the battery level becomes low in the course of normal use, a status icon

appears on the device screen indicating low or very low battery status. In both

cases, connect PC with USB to back up your data, and then recharge your

device as soon as possible.

PA730 User’s Manual

1.4.5 Using The SD/SIM Card

The PA730 has SD/SIM card slots inside the battery compartment.

Inserting a SD/SIM card

1. Remove the battery cover and battery pack.

2. Insert the SD card to the left slot.

3. Insert the SIM card to the right slot.

4. Insert the battery pack and battery cover.

5. Push down the battery cover switch to lock the cover.

13

unitech is a registered trademark of unitech Electronics Co., Ltd.

PA730 User’s Manual

Chapter 2 – Installation &

Operation

2.1 Barcode Setting

unitech is a registered trademark of unitech Electronics Co., Ltd.

1. Tap go to APPS, then tap ScanService.

2. You are now enter the ScanService application. There are three main

items : Settings, Test and Version.

2.1.1 Settings

Tap the default barcode

symbologies for a

different application

PA730 User’s Manual

 For Save / Load Settings, and Factory Default section,

To save data, Please tap and then tap Save / Load

Settings.

unitech is a registered trademark of unitech Electronics Co., Ltd.

Please tap Save Settings – input path - OK

PA730 User’s Manual

The save setting data is stored in File Manager. (Please see 3.2 File Manager )

unitech is a registered trademark of unitech Electronics Co., Ltd.

PA730 User’s Manual

2.1.2 Test

Scanned data

information

2

1

Tap ①

Choose the path and filename to ②

save the scanned data.

PA730 User’s Manual

Version

Show the recent version of ScanService.

Tab to update Scanservice manually.

unitech is a registered trademark of unitech Electronics Co., Ltd.

PA730 User’s Manual

2.2 HF Setting

unitech is a registered trademark of unitech Electronics Co., Ltd.

1. Tap go to APPS, and tap Settings and then under Wireless

& networks, tap More…

2. Tap NFC check box to Enable / disable NFC function.

3. If enable / disable NFC check box, it will also enable / disable Android

Beam too.

4. Make sure that both devices are unlocked and have NFC turned on. If the

other device has an Android Beam option, make sure it is also turned on.

5. Make sure that the NFC area (shaded part) of PA730 and the other phone's

NFC area are close to one another. Experiment by slightly moving the

phones until a connection is made. Tap the screen.

PA730 User’s Manual

2.3 UHF Setting

Current model is not available.

2.4 MSR Setting

Current model is not available.

unitech is a registered trademark of unitech Electronics Co., Ltd.

PA730 User’s Manual

2.5 WWAN Setting

1. Turn off the terminal to insert the SIM card.

Note :



For the instruction, please refer to 1.4.5 Using the Micro SD/SIM Card.

 It only applies to the device which supports WWAN.

2. Turn on the terminal, 4G signal will show at the top of the screen.

If you insert 3G SIM card into PA730, the icon is displayed on the

status bar.

2.5.1 Mobile Network Settings

unitech is a registered trademark of unitech Electronics Co., Ltd.

1. Tap go to APPS, and tap Settings.

Go to Wireless & networks, Tap More, and tap Cellular networks.

PA730 User’s Manual

2. You can have more Cellular network settings in this section.

For network type, please tap Preferred network type.

unitech is a registered trademark of unitech Electronics Co., Ltd.

PA730 User’s Manual

2.6 WLAN Setting

unitech is a registered trademark of unitech Electronics Co., Ltd.

1. Tap go to APPS, and tap Settings and then go to Wireless &

networks, Tap WLAN.

2. To see available networks, turn Wi-Fi ON. And tap to choose the available

networks.

3. Choose the available networks, and enter the Password and tap Connect.

4. If the wireless network that you want is not listed, tap + to manually add it.

5. When enabled, the Wi-Fi icon is displayed on the status bar.

PA730 User’s Manual

2.7 PAN Setting

unitech is a registered trademark of unitech Electronics Co., Ltd.

1. Tap go to APPS, and tap Settings.

2. Select Bluetooth from Wireless & Networks.

3. Tap the Bluetooth tile to turn Bluetooth on.

4. Tap the Bluetooth to see a list of available devices.

5. If prompted to enter a passcode, try 0000 or 1234, or consult the headset

documentation to find the passcode.

6. When enabled, the Bluetooth icon is displayed in the status bar.

When the Bluetooth device is connected, you'll see in the status bar.

Normally, you can easily reconnect your device by switching on Bluetooth on

PA730, and then turning on the device.

However, you might have to connect manually if PA730 has been used with

another Bluetooth device.

PA730 User’s Manual

2.8 GPS Setting

unitech is a registered trademark of unitech Electronics Co., Ltd.

1. Tap go to APPS, and tap Settings.

2. Go to PERSONAL , Tap Location.

3. Tap ON/OFF for the permission to use your location information.

PA730 User’s Manual

4. Tap Mode for more location mode settings.

unitech is a registered trademark of unitech Electronics Co., Ltd.

￭ High accuracy :

Use GPS, Wi-Fi and cellular networks to

determine location

￭ Battery saving :

Use Wi-Fi and cellular networks to determine

location

￭ Device only :

Use GPS to determine location

PA730 User’s Manual

2.9 PC Setting

You can transfer your file from or to your computer. The OS of host side please

use Windows 7 or upper.

1. Connect PA730 to your computer with the USB cable. Your computer will

recognize it is USB charging.

2. Then slide from top, the system will show as follow picture, then you can

select File transfers item.

unitech is a registered trademark of unitech Electronics Co., Ltd.

Use USB for Description

Charging For charging when you connect with PC host.

If your OS of PC host is Windows XP, only this item be selected

and you can’t select other items.

File Transfers For file transfer when you connect with PC host.

You can find a storage device on your PC host site.

Photo Transfer

(PTP)

For file transfer when you connect with PC host.

You can find DCIM folder of storage device on your PC host site.

MIDI For file transfer when you connect with PC host.

You can find some folder of storage device on your PC host site.

3. After connecting the terminal to PC with USB, you can find a removable

storage on my computer.

PA730 User’s Manual

You may also download the Google sync device manager software on your

computer. You can set it up to automatically get music, photos, and videos file

of PA730 to your computer.

Please disable check box of USB debugging on the Developer options item of

android Setting when you want transfer file from computer to PA730.

unitech is a registered trademark of unitech Electronics Co., Ltd.

PA730 User’s Manual

2.10 Camera Setting

2.10.1 Camera Settings

unitech is a registered trademark of unitech Electronics Co., Ltd.

1. Please tap to start Camera App, press to take a picture.

2. Press to do advance setting.

Panorama mode

Video

Camera

PA730 User’s Manual

3. Press to do mode setting

unitech is a registered trademark of unitech Electronics Co., Ltd.

4. Press to do effects setting

unitech is a registered trademark of unitech Electronics Co., Ltd.

PA730 User’s Manual

2.10.2 Video Settings

Press to do advance setting.

2.10.3 Photos & Videos Storage Location

You can choose two different storage ways to save photos & videos : Phone or

SD card. SD Card item can not be activated if no SD Card installed in PA730.

Please see the photo below.

PA730 User’s Manual

2.11 Performing a Hardware Reset

You may have to perform a reset if the device freezes (i.e., the terminal no

longer responds to the buttons or tapping on the screen).

Long press Power button and Volume down button simultaneously to make

the device restart the system within 20 seconds.

unitech is a registered trademark of unitech Electronics Co., Ltd.

PA730 User’s Manual

2.12 Performing Factory Data Reset

unitech is a registered trademark of unitech Electronics Co., Ltd.

1. Tap go to APPS, and tap Settings.

2. You can reset to factory default when you select Factory data reset item, it

will erase all include enterprise folder.

3. You can reset to factory default when you select Network Setting reset

item, it will erase all RF data

Factory Data Reset Network Setting Reset

PA730 User’s Manual

2.13 Programmable Keys

The PA730’s keys can be programmed for users to be able to perform different

functions or applications.

2.13.1 Programming a Physical Key

unitech is a registered trademark of unitech Electronics Co., Ltd.

1. Tap go to APPS, and tap Settings, go to SYSTEM, Tap

Programmable keys

2. Tap Redefine Key to select the physical key to remap.

Then select the redefined type that you prefer : Keycode / Unicode

Note: Power key can not be redefined.

unitech is a registered trademark of unitech Electronics Co., Ltd.

PA730 User’s Manual

3. Please tap Redefine this key after remapping the physical key.

2.13.2 View Redefined Key List

Please tap view redefined key list to check the redefined keys.

To remove all redefined keys, please tap

PA730 User’s Manual

2.14 Battery Swap

Please follow the steps for the battery swap.

1. Long press power button until you see the pop up window and tap Battery

Swap Mode.

2. The LED indicator will start showing solid red light. Please swap the

battery after the LED red light goes off. Make sure do not turn on PA730

during the battery swap process.

3. When the battery swap is done, press the power button to restart PA730.

Note: Please see 1.4.1 Installing the Battery for more information.

unitech is a registered trademark of unitech Electronics Co., Ltd.

PA730 User’s Manual

Chapter 3 – Introduction to

Applications

3.1 Scan Service

unitech is a registered trademark of unitech Electronics Co., Ltd.

1. Tap go to APPS, then tap ScanService.

2. You are now enter the ScanService application. There are three main

items : Settings, Test and Version.

Note : For more Scan Service settings, please refer to 2.1 Barcode Setting.

3.1.1 Test

1. Scanned data information / Save / Clear all scanned data.

Tap Test to start scanning barcodes.

unitech is a registered trademark of unitech Electronics Co., Ltd.

PA730 User’s Manual

2. Aim the Barcode Scan Engine to the barcode and press one of two

scan buttons.

Barcode Scan Engine

3. After scanning the barcodes, the barcode information is as shown

below.

①Tap

② Choose the path and filename to

save the scanned data.

PA730 User’s Manual

3.1.2 More Options

￭ For more options and settings, please tap .

￭ Auto Scan ￭ Scan2key Setting

￭ Device Option ￭ On Screen Button Option ￭ Save / Load

Settings

￭ Update

unitech is a registered trademark of unitech Electronics Co., Ltd.

PA730 User’s Manual

3.2 File Manager

unitech is a registered trademark of unitech Electronics Co., Ltd.

1. Tap go to APPS, and tap File Manager.

: Settings

: Return to the previous page

: Main page

: Refresh

: Folder arrangement

: Folder Information

: Solutions

PA730 User’s Manual

3.3 Update Center

unitech is a registered trademark of unitech Electronics Co., Ltd.

1. Tap go to APPS, and tap Settings, and then tap About

Phone to search for System updates.

Or tap for system updates.

2. To update or check the latest version of software and applications, you will

need to do it manually.

unitech is a registered trademark of unitech Electronics Co., Ltd.

PA730 User’s Manual

3.4 Sound Recorder

1. Tap go to APPS, and tap Sound Recorder.

2. Recording : Tap to start the sound recording.

Record Button Pause

Play

PA730 User’s Manual

3. After recording messages, all the recording files will be saved in

unitech is a registered trademark of unitech Electronics Co., Ltd.

filemanger. Please tap first to refresh all the files.

4. Long press the recording files for more file operations.

PA730 User’s Manual

3.5 Push To Talk

To operate push to talk, please go to Google Play store to download the

walkie talkie apps which can support any android device.

For example, Zello PTT Walkie Talkie is the most recommended

walkie talkie app.

Push to Talk

unitech is a registered trademark of unitech Electronics Co., Ltd.

PA730 User’s Manual

3.6 MoboLink

MoboLink is a software platform that helps unitech customers to remote

manage their purchased devices and applications. The core of the MoboLink

platform provides functionalities in the MDM (Mobile Device Management) and

MAM (Mobile Application Management) domains, and then further extends into

other management functions such as alert notification management and

account management.

unitech is a registered trademark of unitech Electronics Co., Ltd.

1. Tap go to APPS, and tap MoboLink.

MoboLink will run in the background.

Note: If there is no internet connection, MoboLink will be activated after few seconds.

PA730 User’s Manual

2. MoboLink setting is shown as below :

Enter MoboLink server URL manually

in the text field or scan a MoboLink

server URL Barcode

unitech is a registered trademark of unitech Electronics Co., Ltd.

Tap “Save” to initiate MoboLink Server URL

PA730 User’s Manual

3. MoboLink screen information is as below:

Slide ON/OFF button to show MoboLink

unitech is a registered trademark of unitech Electronics Co., Ltd.

Tap “Exit” to leave the screen

PA730 User’s Manual

3.6.1 More about MoboLink

For detailed operation, solution and usage, please refer to

MoboLink user’s guide. ( http://mobolink.tw.ute.com/support )

unitech is a registered trademark of unitech Electronics Co., Ltd.

PA730 User’s Manual

3.7 SOTI

PA730 is supported by SOTI which provides advanced helpdesk solutions for

our users. To download SOTI, please go to : https://www.soti.net/oem

unitech is a registered trademark of unitech Electronics Co., Ltd.

Quectel Wireless Solutions 201607EC25V LTE Module User Manual

Quectel Wireless Solutions Company Limited LTE Module

Contents

User manual

Navigation menu

Namespaces

Views

Navigation