Quectel Wireless Solutions 201609MC20 GSM/GPRS/GNSS Module User Manual

Quectel Wireless Solutions Company Limited GSM/GPRS/GNSS Module

201609MC20 User Manual PDF Download & Text

User Manual

Download:
Mirror Download [FCC.gov]
Document ID	3169134
Application ID	BOOOzGd107L7gbvAWB/7KQ==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	227.67kB (2845832 bits)
Date Submitted	2016-10-20 00:00:00
Date Available	2016-10-21 00:00:00
Creation Date	2016-10-10 10:14:21
Producing Software	Acrobat Distiller 9.0.0 (Windows)
Document Lastmod	2016-10-10 10:14:21
Document Title	Microsoft Word - Quectel_MC20_Hardware_Design_V1.0_FCC
Document Creator	PScript5.dll Version 5.2.2
Document Author:	lenovo

MC20 Hardware Design
GSM/GPRS/GNSS Module Series
Rev. MC20_Hardware_Design_V1.0
Date: 2016-07-12
www.quectel.com
GSM/GPRS/GNSS Module Series
MC20 Hardware Design
Our aim is to provide customers with timely and comprehensive service. For any
assistance, please contact our company headquarters:
Quectel Wireless Solutions Co., Ltd.
Office 501, Building 13, No.99, Tianzhou Road, Shanghai, China, 200233
Tel: +86 21 5108 6236
Email: info@quectel.com
Or our local office. For more information, please visit:
http://www.quectel.com/support/salesupport.aspx
For technical support, or to report documentation errors, please visit:
http://www.quectel.com/support/techsupport.aspx
Or email to: Support@quectel.com
GENERAL NOTES
QUECTEL OFFERS THE INFORMATION AS A SERVICE TO ITS CUSTOMERS. THE INFORMATION
PROVIDED IS BASED UPON CUSTOMERS’ REQUIREMENTS. QUECTEL MAKES EVERY EFFORT
TO ENSURE THE QUALITY OF THE INFORMATION IT MAKES AVAILABLE. QUECTEL DOES NOT
MAKE ANY WARRANTY AS TO THE INFORMATION CONTAINED HEREIN, AND DOES NOT ACCEPT
ANY LIABILITY FOR ANY INJURY, LOSS OR DAMAGE OF ANY KIND INCURRED BY USE OF OR
RELIANCE UPON THE INFORMATION. ALL INFORMATION SUPPLIED HEREIN IS SUBJECT TO
CHANGE WITHOUT PRIOR NOTICE.
COPYRIGHT
THE INFORMATION CONTAINED HERE IS PROPRIETARY TECHNICAL INFORMATION OF QUECTEL
CO., LTD. TRANSMITTING, REPRODUCTION, DISSEMINATION AND EDITING OF THIS DOCUMENT
AS WELL AS UTILIZATION OF THE CONTENT ARE FORBIDDEN WITHOUT PERMISSION.
OFFENDERS WILL BE HELD LIABLE FOR PAYMENT OF DAMAGES. ALL RIGHTS ARE RESERVED
IN THE EVENT OF A PATENT GRANT OR REGISTRATION OF A UTILITY MODEL OR DESIGN.
Copyright © Quectel Wireless Solutions Co., Ltd. 2016. All rights reserved.
MC20_Hardware_Design
Confidential / Released
1 / 95
GSM/GPRS/GNSS Module Series
MC20 Hardware Design
About the Document
History
Revision
Date
Author
Description
1.0
2016-07-12
Tiger CHENG
Initial
MC20_Hardware_Design
Confidential / Released
2 / 95
GSM/GPRS/GNSS Module Series
MC20 Hardware Design
Contents
About the Document ................................................................................................................................ 2
Contents .................................................................................................................................................... 3
Table Index ............................................................................................................................................... 6
Figure Index .............................................................................................................................................. 8
Introduction ..................................................................................................................................... 10
1.1.
Safety Information ................................................................................................................. 10
Product Concept ............................................................................................................................. 12
2.1.
General Description .............................................................................................................. 12
2.2.
Directives and Standards ...................................................................................................... 13
2.2.1.
2.2.1. FCC Statement .................................................................................................. 13
2.2.2.
FCC Radiation Exposure Statement ............................................................................ 13
2.3.
Key Features ......................................................................................................................... 13
2.4.
Functional Diagram ............................................................................................................... 17
2.5.
Evaluation Board ................................................................................................................... 18
Application Functions..................................................................................................................... 19
3.1.
Pin of Module ........................................................................................................................ 20
3.1.1.
Pin Assignment ............................................................................................................ 20
3.1.2.
Pin Description............................................................................................................. 21
3.2.
Application Modes Introduction ............................................................................................. 25
3.3.
Power Supply ........................................................................................................................ 27
3.3.1.
Power Features ........................................................................................................... 27
3.3.2.
Decrease Supply Voltage Drop .................................................................................... 28
3.3.2.1.
Decrease Supply Voltage Drop for GSM Part.................................................. 28
3.3.2.2.
Decrease Supply Voltage Drop for GNSS Part................................................ 29
3.3.3.
Reference Design for Power Supply ............................................................................ 30
3.3.3.1.
Reference Design for Power Supply of GSM Part ........................................... 30
3.3.3.2.
Reference Design for Power Supply of GNSS Part ......................................... 31
3.3.4.
Monitor Power Supply .................................................................................................. 31
3.3.5.
Backup Domain of GNSS ............................................................................................ 31
3.4.
Operating Modes .................................................................................................................. 32
3.4.1.
Operating Modes of GSM Part..................................................................................... 32
3.4.1.1.
Minimum Functionality Mode ........................................................................... 33
3.4.1.2.
SLEEP Mode ................................................................................................... 34
3.4.1.3.
Wake up GSM Part from SLEEP Mode ........................................................... 34
3.4.2.
Operating Modes of GNSS Part................................................................................... 34
3.4.2.1.
Full on Mode.................................................................................................... 34
3.4.2.2.
Standby Mode ................................................................................................. 36
3.4.2.3.
Backup Mode .................................................................................................. 36
MC20_Hardware_Design
Confidential / Released
3 / 95
GSM/GPRS/GNSS Module Series
MC20 Hardware Design
3.4.3.
Summary of GSM and GNSS Parts’ State in All-in-one Solution.................................. 37
3.4.4.
Summary of GSM and GNSS Parts’ State in Stand-alone Solution ............................. 37
3.5.
Power on and down .............................................................................................................. 38
3.5.1.
Power on ..................................................................................................................... 38
3.5.2.
Power down ................................................................................................................. 40
3.5.2.1.
Power down Module Using the PWRKEY Pin ................................................. 40
3.5.2.2.
Power down Module Using AT Command ....................................................... 41
3.5.2.3.
Power down GNSS Part Alone Using AT Command ....................................... 42
3.5.2.4.
Under-voltage Automatic Shutdown ................................................................ 42
3.6.
Serial Interfaces .................................................................................................................... 43
3.6.1.
UART Port ................................................................................................................... 45
3.6.1.1.
Features of UART Port .................................................................................... 45
3.6.1.2.
The Connection of UART ................................................................................ 46
3.6.1.3.
Firmware Upgrade........................................................................................... 48
3.6.2.
Debug Port................................................................................................................... 49
3.6.3.
Auxiliary UART Port and GNSS UART Port ................................................................. 49
3.6.3.1.
Connection in All-in-one Solution..................................................................... 49
3.6.3.2.
Connection in Stand-alone Solution ................................................................ 50
3.6.4.
UART Application ......................................................................................................... 51
3.7.
Audio Interfaces .................................................................................................................... 52
3.7.1.
Decrease TDD Noise and Other Noises ...................................................................... 54
3.7.2.
Microphone Interfaces Design ..................................................................................... 54
3.7.3.
Receiver and Speaker Interface Design ...................................................................... 55
3.7.4.
Earphone Interface Design .......................................................................................... 56
3.7.5.
Loud Speaker Interface Design.................................................................................... 56
3.7.6.
Audio Characteristics ................................................................................................... 57
3.8.
SIM Card Interface ................................................................................................................ 57
3.9.
ADC ...................................................................................................................................... 61
3.10. Behaviors of the RI ............................................................................................................... 61
3.11. Network Status Indication...................................................................................................... 63
3.12. EASY Autonomous AGPS Technology ................................................................................. 64
3.13. EPO Offline AGPS Technology ............................................................................................. 64
3.14. Multi-tone AIC ....................................................................................................................... 65
Antenna Interface ............................................................................................................................ 66
4.1.
GSM Antenna Interface ......................................................................................................... 66
4.1.1.
Reference Design ........................................................................................................ 66
4.1.2.
RF Output Power ......................................................................................................... 67
4.1.3.
RF Receiving Sensitivity .............................................................................................. 68
4.1.4.
Operating Frequencies ................................................................................................ 68
4.1.5.
RF Cable Soldering ..................................................................................................... 68
4.2.
GNSS Antenna Interface ....................................................................................................... 69
4.2.1.
Antenna Specifications ................................................................................................ 69
4.2.2.
Active Antenna ............................................................................................................. 70
4.2.3.
Passive Antenna .......................................................................................................... 71
MC20_Hardware_Design
Confidential / Released
4 / 95
GSM/GPRS/GNSS Module Series
MC20 Hardware Design
4.3.
Bluetooth Antenna Interface .................................................................................................. 71
Electrical, Reliability and Radio Characteristics .......................................................................... 74
5.1.
Absolute Maximum Ratings .................................................................................................. 74
5.2.
Operating Temperature ......................................................................................................... 74
5.3.
Power Supply Ratings ........................................................................................................... 75
5.4.
Current Consumption ............................................................................................................ 77
5.5.
Electrostatic Discharge ......................................................................................................... 79
Mechanical Dimensions.................................................................................................................. 81
6.1.
Mechanical Dimensions of Module ....................................................................................... 81
6.2.
Recommended Footprint....................................................................................................... 83
6.3.
Top and Bottom View of the Module...................................................................................... 84
Storage and Manufacturing ............................................................................................................ 85
7.1.
Storage.................................................................................................................................. 85
7.2.
Soldering ............................................................................................................................... 85
7.3.
Packaging ............................................................................................................................. 86
7.3.1.
Tape and Reel Packaging ............................................................................................ 87
Appendix A References .................................................................................................................. 88
Appendix B GPRS Coding Schemes ............................................................................................. 93
10 Appendix C GPRS Multi-slot Classes ............................................................................................ 95
MC20_Hardware_Design
Confidential / Released
5 / 95
GSM/GPRS/GNSS Module Series
MC20 Hardware Design
Table Index
TABLE 1: KEY FEATURES (GMS/GPRS PART OF MC20) .................................................................... 13
TABLE 2: CODING SCHEMES AND MAXIMUM NET DATA RATES OVER AIR INTERFACE ............... 15
TABLE 3: KEY FEATURES (GNSS PART OF MC20) ............................................................................. 16
TABLE 4: PROTOCOLS SUPPORTED BY THE MODULE..................................................................... 17
TABLE 5: I/O PARAMETERS DEFINITION ............................................................................................. 21
TABLE 6: PIN DESCRIPTION ................................................................................................................. 21
TABLE 7: MULTIPLEXED FUNCTIONS .................................................................................................. 25
TABLE 8: COMPARISON BETWEEN ALL-IN-ONE AND STAND-ALONE SOLUTION ........................... 27
TABLE 9: OPERATING MODES OVERVIEW OF GSM PART ................................................................ 32
TABLE 10: DEFAULT CONFIGURATION OF FULL ON MODE (GNSS PART) ...................................... 35
TABLE 11: COMBINATION STATES OF GSM AND GNSS PARTS IN ALL-IN-ONE SOLUTION ........... 37
TABLE 12: COMBINATION STATES OF GSM AND GNSS PARTS IN STAND-ALONE SOLUTION ...... 37
TABLE 13: LOGIC LEVELS OF THE UART INTERFACE ....................................................................... 44
TABLE 14: PIN DEFINITION OF THE UART INTERFACES ................................................................... 44
TABLE 15: PIN DEFINITION OF AUDIO INTERFACE ............................................................................ 52
TABLE 16: AOUT2 OUTPUT CHARACTERISTICS ................................................................................ 53
TABLE 17: TYPICAL ELECTRET MICROPHONE CHARACTERISTICS................................................ 57
TABLE 18: TYPICAL SPEAKER CHARACTERISTICS ........................................................................... 57
TABLE 19: PIN DEFINITION OF THE SIM INTERFACE......................................................................... 58
TABLE 20: PIN DEFINITION OF THE ADC............................................................................................. 61
TABLE 21: CHARACTERISTICS OF THE ADC ...................................................................................... 61
TABLE 22: BEHAVIORS OF THE RI ....................................................................................................... 61
TABLE 23: WORKING STATE OF THE NETLIGHT ................................................................................ 63
TABLE 24: PIN DEFINITION OF THE RF_ANT ...................................................................................... 66
TABLE 25: ANTENNA CABLE REQUIREMENTS ................................................................................... 67
TABLE 26: ANTENNA REQUIREMENTS ................................................................................................ 67
TABLE 27: RF OUTPUT POWER ........................................................................................................... 67
TABLE 28: RF RECEIVING SENSITIVITY .............................................................................................. 68
TABLE 29: OPERATING FREQUENCIES............................................................................................... 68
TABLE 30: RECOMMENDED ANTENNA SPECIFICATIONS ................................................................. 69
TABLE 31: PIN DEFINITION OF THE BT_ANT ...................................................................................... 72
TABLE 32: ABSOLUTE MAXIMUM RATINGS ........................................................................................ 74
TABLE 33: OPERATING TEMPERATURE .............................................................................................. 75
TABLE 34: POWER SUPPLY RATINGS OF GSM PART (GNSS IS POWERED OFF) ........................... 75
TABLE 35: POWER SUPPLY RATINGS OF GNSS PART ...................................................................... 76
TABLE 36: CURRENT CONSUMPTION OF GSM PART (GNSS IS POWERED OFF) .......................... 77
TABLE 37: CURRENT CONSUMPTION OF THE GNSS PART .............................................................. 79
TABLE 38: ESD ENDURANCE (TEMPERATURE: 25ºC, HUMIDITY: 45%) ........................................... 79
TABLE 39: REEL PACKAGING ............................................................................................................... 87
TABLE 40: RELATED DOCUMENTS ...................................................................................................... 88
TABLE 41: TERMS AND ABBREVIATIONS ............................................................................................ 89
MC20_Hardware_Design
Confidential / Released
6 / 95
GSM/GPRS/GNSS Module Series
MC20 Hardware Design
TABLE 42: DESCRIPTION OF DIFFERENT CODING SCHEMES ......................................................... 93
TABLE 43: GPRS MULTI-SLOT CLASSES ............................................................................................. 95
MC20_Hardware_Design
Confidential / Released
7 / 95
GSM/GPRS/GNSS Module Series
MC20 Hardware Design
Figure Index
FIGURE 1: MODULE FUNCTIONAL DIAGRAM ..................................................................................... 18
FIGURE 2: PIN ASSIGNMENT ............................................................................................................... 20
FIGURE 3: ALL-IN-ONE SOLUTION SCHEMATIC DIAGRAM ............................................................... 26
FIGURE 4: STAND-ALONE SOLUTION SCHEMATIC DIAGRAM .......................................................... 26
FIGURE 5: VOLTAGE RIPPLE DURING TRANSMITTING (GSM PART) ............................................... 28
FIGURE 6: REFERENCE CIRCUIT FOR THE VBAT INPUT (GSM PART) ............................................ 29
FIGURE 7: REFERENCE CIRCUIT FOR THE GNSS_VCC INPUT ....................................................... 29
FIGURE 8: REFERENCE CIRCUIT FOR POWER SUPPLY OF THE GSM PART ................................. 30
FIGURE 9: REFERENCE CIRCUIT DESIGN FOR GNSS PART ............................................................ 31
FIGURE 10: INTERNAL GNSS’S BACKUP DOMAIN POWER CONSTRUCTION ................................. 32
FIGURE 11: TURN ON THE MODULE WITH AN OPEN-COLLECTOR DRIVER ................................... 38
FIGURE 12: TURN ON THE MODULE WITH A BUTTON ...................................................................... 39
FIGURE 13: TURN-ON TIMING .............................................................................................................. 39
FIGURE 14: TURN-OFF TIMING BY USING THE PWRKEY PIN ........................................................... 41
FIGURE 15: TURN-OFF TIMING OF GNSS PART BY USING AT COMMAND ...................................... 42
FIGURE 16: REFERENCE DESIGN FOR FULL-FUNCTION UART ...................................................... 47
FIGURE 17: REFERENCE DESIGN FOR UART PORT (THREE LINE CONNECTION) ........................ 47
FIGURE 18: REFERENCE DESIGN FOR UART PORT WITH HARDWARE FLOW CONTROL............ 48
FIGURE 19: REFERENCE DESIGN FOR FIRMWARE UPGRADE ....................................................... 48
FIGURE 20: REFERENCE DESIGN FOR DEBUG PORT ...................................................................... 49
FIGURE 21: AUXILIARY AND GNSS UART PORT CONNECTION IN ALL-IN-ONE SOLUTION ........... 50
FIGURE 22: AUXILIARY AND GNSS UART PORT CONNECTION IN STAND-ALONE SOLUTION ...... 51
FIGURE 23: LEVEL MATCH DESIGN FOR 3.3V SYSTEM .................................................................... 51
FIGURE 24: SKETCH MAP FOR RS-232 INTERFACE MATCH ............................................................ 52
FIGURE 25: REFERENCE DESIGN FOR AIN ........................................................................................ 54
FIGURE 26: HANDSET INTERFACE DESIGN FOR AOUT1 .................................................................. 55
FIGURE 27: SPEAKER INTERFACE DESIGN WITH AN AMPLIFIER FOR AOUT1 .............................. 55
FIGURE 28: EARPHONE INTERFACE DESIGN .................................................................................... 56
FIGURE 29: LOUD SPEAKER INTERFACE DESIGN ............................................................................ 56
FIGURE 30: REFERENCE CIRCUIT FOR SIM1 INTERFACE WITH AN 8-PIN SIM CARD HOLDER ... 59
FIGURE 31: REFERENCE CIRCUIT FOR SIM1 INTERFACE WITH A 6-PIN SIM CARD HOLDER ...... 59
FIGURE 32: REFERENCE CIRCUIT FOR SIM2 INTERFACE WITH A 6-PIN SIM CARD HOLDER ...... 60
FIGURE 33: RI BEHAVIOR AS A RECEIVER WHEN VOICE CALLING ................................................. 62
FIGURE 34: RI BEHAVIOR AS A CALLER.............................................................................................. 62
FIGURE 35: RI BEHAVIOR WHEN URC OR SMS RECEIVED .............................................................. 62
FIGURE 36: REFERENCE DESIGN FOR NETLIGHT ............................................................................ 63
FIGURE 37: REFERENCE DESIGN FOR GSM ANTENNA ................................................................... 66
FIGURE 38: RF SOLDERING SAMPLE ................................................................................................. 69
FIGURE 39: REFERENCE DESIGN WITH ACTIVE ANTENNA ............................................................. 70
FIGURE 40: REFERENCE DESIGN WITH PASSIVE ANTENNA ........................................................... 71
FIGURE 41: REFERENCE DESIGN FOR BLUETOOTH ANTENNA ...................................................... 72
MC20_Hardware_Design
Confidential / Released
8 / 95
GSM/GPRS/GNSS Module Series
MC20 Hardware Design
FIGURE 42: MC20 TOP AND SIDE DIMENSIONS (UNIT: MM).............................................................. 81
FIGURE 43: MC20 BOTTOM DIMENSIONS (UNIT: MM) ....................................................................... 82
FIGURE 44: RECOMMENDED FOOTPRINT (UNIT: MM) ...................................................................... 83
FIGURE 45: TOP VIEW OF THE MODULE ............................................................................................ 84
FIGURE 46: BOTTOM VIEW OF THE MODULE .................................................................................... 84
FIGURE 47: REFLOW SOLDERING THERMAL PROFILE .................................................................... 86
FIGURE 48: TAPE AND REEL SPECIFICATION .................................................................................... 87
FIGURE 49: DIMENSIONS OF REEL ..................................................................................................... 87
FIGURE 50: RADIO BLOCK STRUCTURE OF CS-1, CS-2 AND CS-3.................................................. 93
FIGURE 51: RADIO BLOCK STRUCTURE OF CS-4 ............................................................................. 94
MC20_Hardware_Design
Confidential / Released
9 / 95
GSM/GPRS/GNSS Module Series
MC20 Hardware Design
Introduction
This document defines the MC20 module and describes its hardware interface which is connected with
the customer application as well as its air interface.
The document can help you quickly understand module interface specifications, as well as the electrical
and mechanical details. Associated with application note and user guide, you can use MC20 module to
design and set up mobile applications easily.
1.1. Safety Information
The following safety precautions must be observed during all phases of the operation, such as usage,
service or repair of any cellular terminal or mobile incorporating MC20 module. Manufacturers of the
cellular terminal should send the following safety information to users and operating personnel, and
incorporate these guidelines into all manuals supplied with the product. If not so, Quectel assumes no
liability for the customer’s failure to comply with these precautions.
Full attention must be given to driving at all times in order to reduce the risk of an
accident. Using a mobile while driving (even with a handsfree kit) causes
distraction and can lead to an accident. You must comply with laws and regulations
restricting the use of wireless devices while driving.
Switch off the cellular terminal or mobile before boarding an aircraft. Make sure it is
switched off. The operation of wireless appliances in an aircraft is forbidden, so as
to prevent interference with communication systems. Consult the airline staff about
the use of wireless devices on boarding the aircraft, if your device offers a Airplane
Mode which must be enabled prior to boarding an aircraft.
Switch off your wireless device when in hospitals, clinics or other health care
facilities. These requests are desinged to prevent possible interference with
sentitive medical equipment.
MC20_Hardware_Design
Confidential / Released
10 / 95
GSM/GPRS/GNSS Module Series
MC20 Hardware Design
Cellular terminals or mobiles operating over radio frequency signal and cellular
network cannot be guaranteed to connect in all conditions, for example no mobile
fee or with an invalid SIM card. While you are in this condition and need emergent
help, please remember using emergency call. In order to make or receive a call,
the cellular terminal or mobile must be switched on and in a service area with
adequate cellular signal strength.
Your cellular terminal or mobile contains a transmitter and receiver. When it is ON ,
it receives and transmits radio frequency energy. RF interference can occur if it is
used close to TV set, radio, computer or other electric equipment.
In locations with potencially explosive atmospheres, obey all posted signs to turn
off wireless devices such as your phone or other cellular terminals. Areas with
potencially explosive atmospheres include fuelling areas, below decks on boats,
fuel or chemical transfer or storage facilities, areas where the air contains
chemicals or particles such as grain, dust or metal powders, etc.
MC20_Hardware_Design
Confidential / Released
11 / 95
GSM/GPRS/GNSS Module Series
MC20 Hardware Design
Product Concept
2.1. General Description
MC20 is a multi-purpose module which integrates a high performance GNSS engine and a quad-band
GSM/GPRS engine. It can work as all-in-one solution or stand-alone solution according to customers'
application demands. For detailed introduction on all-in-one solution and stand-alone solution, please
refer to Chapter 3.2.
The quad-band GSM/GPRS engine can work at frequencies of GSM850MHz, EGSM900MHz,
DCS1800MHz and PCS1900MHz. MC20 features GPRS multi-slot class 12 and supports the GPRS
coding schemes CS-1, CS-2, CS-3 and CS-4. For more details about GPRS multi-slot classes and coding
schemes, please refer to the Appendix B & C.
The GNSS engine is a single receiver integrating GPS and BeiDou systems. It supports multiple
positioning and navigation systems including autonomous GPS, BeiDou, SBAS (including WAAS,
EGNOS, MSAS and GAGAN), and QZSS. It is able to achieve the industry’s highest level of sensitivity,
accuracy and TTFF with the lowest power consumption. The embedded flash memory provides capacity
for storing user-specific configurations and allows for future updates.
MC20 is an SMD type module with 54 LCC pads and 14 LGA pads which can be easily embedded into
applications. With a compact profile of 18.7mm × 16.0mm × 2.1mm, the module can meet almost all the
requirements for M2M applications, including vehicle and personal tracking, wearable devices, security
systems, wireless POS, industrial PDA, smart metering, remote maintenance & control, etc.
Designed with power saving technique, the current consumption of MC20’s GSM part is as low as 1.2mA
in SLEEP mode when DRX is 5 and the GNSS part is powered off. The GNSS engine also has many
advanced power saving modes including standby and backup modes which can fit the requirement of
low-power consumption in different scenes.
GSM part of MC20 is integrated with Internet service protocols such as TCP, UDP, PPP, HTTP and FTP.
Extended AT commands have been developed for you to use these Internet service protocols easily.
EASY technology as a key feature of GNSS part of MC20 module is one kind of AGPS. Capable of
collecting and processing all internal aiding information like GNSS time, ephemeris, last position, etc., the
GNSS part will have a fast TTFF in either Hot or Warm start.
MC20_Hardware_Design
Confidential / Released
12 / 95
GSM/GPRS/GNSS Module Series
MC20 Hardware Design
The module fully complies with the RoHS directive of the European Union.
2.2. Directives and Standards
The MC20module is designed to comply with the FCC statements. FCC ID: XMR201609MC20
The Host system using MC20 should have label “contains FCC ID: XMR201609MC20”.
2.2.1. 2.2.1. FCC Statement
Changes or modifications not expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
2.2.2. FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance 20cm between the radiator and
your body as well as kept minimum 20cm from radio antenna depending on the Mobile status of this
module usage. This module should NOT be installed and operating simultaneously with other radio. The
manual of the host system, which uses MC20, must include RF exposure warning statement to advice
user should keep minimum 20cm from the radio antenna of MC20 module depending on the Mobile status.
Note: If a portable device (such as PDA) uses MC20 module, the device needs to do permissive change
and SAR testing.
The following list indicates the performance of antenna gain in certificate testing.
Part
Number
Frequency Range (MHz)
Peak Gain
(XZ-V)
Average
Gain(XZ-V)
VSWR
Impedance
3R007
GSM850:824～894MHz
PCS1900: 1850～1990MHz
1 dBi typ.
1 dBi typ.
2 max
50Ω
2.3. Key Features
The following table describes the detailed features of MC20 module.
Table 1: Key Features (GMS/GPRS Part of MC20)
Features
MC20_Hardware_Design
Implementation
Confidential / Released
13 / 95
GSM/GPRS/GNSS Module Series
MC20 Hardware Design
Power Supply
Single supply voltage: 3.3V ~ 4.6V
Typical supply voltage: 4V
Power Saving
Typical power consumption in SLEEP mode (GNSS is powered off):
1.2mA@DRX=5
0.8mA@DRX=9
Frequency Bands




GSM Class
Small MS
Transmitting Power


Class 4 (2W) at GSM850 and EGSM900
Class 1 (1W) at DCS1800 and PCS1900
GPRS Connectivity



GPRS multi-slot class 12 (default)
GPRS multi-slot class 1~12 (configurable)
GPRS mobile station class B







GPRS data downlink transfer: max. 85.6kbps
GPRS data uplink transfer: max. 85.6kbps
Coding scheme: CS-1, CS-2, CS-3 and CS-4
Support the protocols PAP (Password Authentication Protocol)
usually used for PPP connections
Internet service protocols TCP/UDP, FTP, PPP, HTTP, NTP, PING
Support Packet Broadcast Control Channel (PBCCH)
Support Unstructured Supplementary Service Data (USSD)
Temperature Range


Operation temperature range: -35°C ~ +75°C 1)
Extended temperature range: -40°C ~ +85°C 2)
SMS


Text and PDU mode
SMS storage: SIM card
SIM Interface


Support SIM card: 1.8V, 3.0V
Support Dual SIM Single Standby
Audio Features
Speech codec modes:
 Half Rate (ETS 06.20)
 Full Rate (ETS 06.10)
 Enhanced Full Rate (ETS 06.50/06.60/06.80)
 Adaptive Multi-Rate (AMR)
 Echo Suppression
 Noise Reduction
 Embedded one amplifier of class AB with maximum driving power up
to 800mW
DATA GPRS
UART Interfaces
UART Port:
 Seven lines on UART port interface
 Used for AT command and GPRS data

MC20_Hardware_Design
Quad-band: GSM850, EGSM900, DCS1800, PCS1900.
The module can search these frequency bands automatically
The frequency bands can be set by AT commands
Compliant to GSM Phase 2/2+
Used for PMTK command and NMEA output in all-in-one solution
Confidential / Released
14 / 95
GSM/GPRS/GNSS Module Series
MC20 Hardware Design
 Multiplexing function
 Support autobauding from 4800bps to 115200bps
Debug Port:
 Two lines on debug port interface DBG_TXD and DBG_RXD
 Debug port only used for firmware debugging
Auxiliary Port:
 Two lines on auxiliary port interface: TXD_AUX and RXD_AUX

Used for communication with the GNSS Part in all-in-one solution
Phonebook Management
Support phonebook types: SM, ME, ON, MC, RC, DC, LD, LA
SIM Application Toolkit
Support SAT class 3, GSM 11.14 Release 99
Physical Characteristics
Size: (18.7±0.15) × (16±0.15) × (2.1±0.2)mm
Weight: Approx. 1.3g
Firmware Upgrade
Firmware upgrade via UART port
Antenna Interface
Connected to antenna pad with 50 Ohm impedance control
NOTES
1.
2.
1)
Within operation temperature range, the module is 3GPP compliant.
Within extended temperature range, the module remains the ability to establish and maintain a
voice, SMS, data transmission, emergency call, etc. There is no unrecoverable malfunction. There
are also no effects on radio spectrum and no harm to radio network. Only one or more parameters like
Pout might reduce in their value and exceed the specified tolerances. When the temperature returns to
the normal operating temperature levels, the module will meet 3GPP compliant again.
2)
Table 2: Coding Schemes and Maximum Net Data Rates over Air Interface
Coding Scheme
1 Timeslot
2 Timeslot
4 Timeslot
CS-1
9.05kbps
18.1kbps
36.2kbps
CS-2
13.4kbps
26.8kbps
53.6kbps
CS-3
15.6kbps
31.2kbps
62.4kbps
CS-4
21.4kbps
42.8kbps
85.6kbps
MC20_Hardware_Design
Confidential / Released
15 / 95
GSM/GPRS/GNSS Module Series
MC20 Hardware Design
Table 3: Key Features (GNSS Part of MC20)
Features
Implementation
GNSS

GPS+BeiDou
Power Supply

Supply voltage: 2.8V~4.3V
Power Consumption






Acquisition: 25mA @-130dBm (GPS)
Tracking: 19mA @-130dBm (GPS)
Acquisition: 23mA @-130dBm (GPS+BeiDou)
Tracking: 18mA @-130dBm (GPS+BeiDou)
Standby: 300uA @VCC=3.3V
Backup: 14uA @V_BCKP=3.3V
Receiver Type


GPS L1 1575.42MHz C/A Code
BeiDou B1 1561.098MHz C/A Code
Sensitivity
GPS+BeiDou



Acquisition: -148dBm
Reacquisition: -160dBm
Tracking: -163dBm
Time-to-First-Fix
(EASY Enabled) 1)



Cold Start: <15s average @-130dBm
Warm Start: <5s average @-130dBm
Hot Start: 1s @-130dBm
Time-to-First-Fix
(EASY Disabled)



Cold Start (Autonomous): <35s average @-130dBm
Warm Start (Autonomous): <30s average @-130dBm
Hot Start (Autonomous): 1s @-130dBm
Horizontal Position
Accuracy (Autonomous)

<2.5 m CEP @-130dBm
Update Rate

Up to 10Hz, 1Hz by default
Velocity Accuracy

Without aid: 0.1m/s
Acceleration Accuracy

Without aid: 0.1m/s²
Dynamic Performance



Maximum Altitude: 18,000m
Maximum Velocity: 515m/s
Acceleration: 4G


GNSS UART port: GNSS_TXD and GNSS_ RXD
Support baud rate from 4800bps to 115200bps; 115200bps by
default


Used for communication with the GSM Part in all-in-one solution
Used for communication with peripherals in stand-alone solution
GNSS UART Port
Typical: 3.3V
NOTE
MC20_Hardware_Design
Confidential / Released
16 / 95
GSM/GPRS/GNSS Module Series
MC20 Hardware Design
1)
In this mode, GNSS part’s backup domain should be valid.
Table 4: Protocols Supported by the Module
Protocol
Type
NMEA
output, ASCII, 0183, 3.01
PMTK
Input/output, MTK proprietary protocol
NOTE
Please refer to document [2] for details of NMEA standard protocol and MTK proprietary protocol.
2.4. Functional Diagram
The following figure shows a block diagram of MC20 and illustrates the major functional parts.



Radio frequency part
Power management
Peripheral interfaces
—Power supply
—Turn-on/off interface
—UART interface
—Audio interface
—SIM interface
—ADC interface
—RF interface
—PCM interface
—BT interface
—SD interface
MC20_Hardware_Design
Confidential / Released
17 / 95
GSM/GPRS/GNSS Module Series
MC20 Hardware Design
Figure 1: Module Functional Diagram
2.5. Evaluation Board
In order to help you develop applications with MC20, Quectel supplies an evaluation board (EVB), TE-A
board, RS-232 to USB cable, power adapter, earphone, GSM antenna, GNSS antenna and other
peripherals to control or test the module. For details, please refer to document [11].
MC20_Hardware_Design
Confidential / Released
18 / 95
GSM/GPRS/GNSS Module Series
MC20 Hardware Design
Application Functions
MC20 is an SMD type module with 54 LCC pads and 14 LGA pads. The following chapters provide
detailed descriptions about these pins.
















Pin of module
Power supply
Operating modes
Power on/down
Power saving
Backup domain of GNSS
Serial interfaces
Audio interfaces
SIM card interface
ADC
Behaviors of the RI
Network status indication
RF transmitting signal indication
EASY autonomous AGPS technology
EPO offline AGPS technology
Multi-tone AIC
MC20_Hardware_Design
Confidential / Released
19 / 95
GSM/GPRS/GNSS Module Series
MC20 Hardware Design
3.1. Pin of Module
3.1.1. Pin Assignment
Figure 2: Pin Assignment
NOTE
Please keep all reserved pins open.
MC20_Hardware_Design
Confidential / Released
20 / 95
GSM/GPRS/GNSS Module Series
MC20 Hardware Design
3.1.2. Pin Description
Table 5: I/O Parameters Definition
Type
Description
IO
Bidirectional input/output
DI
Digital input
DO
Digital output
PI
Power input
PO
Power output
AI
Analog input
AO
Analog output
Table 6: Pin Description
Power Supply
PIN Name
VBAT
PIN No.
50, 51
I/O
Description
DC Characteristics
Comment
PI
Power supply of
GSM/GPRS part:
VBAT=3.3V~4.6V
VImax=4.6V
VImin=3.3V
VInorm=4.0V
It must be able to
provide sufficient
current up to 1.6A
in a transmitting
burst.
Power supply of GNSS
part:
GNSS_VCC=2.8V~4.3V
VImax=4.3V
VImin=2.8V
VInorm=3.3V
Assure load
current no less
than 150mA.
GNSS_
VCC
26
PI
VRTC
52
IO
Keep this pin
open
PO
1. If unused, keep
this pin open.
2. Recommend
adding a
2.2~4.7uF bypass
capacitor, when
using this pin for
power supply.
VDD_
EXT
43
GND
14,27,
MC20_Hardware_Design
Supply 2.8V voltage for
external circuit.
VOmax=2.9V
VOmin=2.7V
VOnorm=2.8V
IOmax=20mA
Ground
Confidential / Released
21 / 95
GSM/GPRS/GNSS Module Series
MC20 Hardware Design
31,40,
42,44,
45,48,
49
Turn on/off
PIN Name
PWRKEY
PIN No.
I/O
Description
DC Characteristics
DI
Power on/off key.
PWRKEY should be
pulled down for a
moment to turn on or
turn off the system.
VILmax=
0.1×VBAT
VIHmin=
0.6×VBAT
VIHmax=3.1V
DC Characteristics
Comment
Audio Interface
PIN Name
PIN No.
I/O
Description
MICP
MICN
1,
AI
Positive and negative
voice input
If unused, keep
these pins open.
Channel 1 positive and
negative voice output
If unused, keep
these pins open.
Support both
voice and
ringtone output.
SPKP
SPKN
3,
AO
Refer to Chapter 3.7.6
LOUD
SPKP
LOUD
SPKN
54
53
AO
Channel 2 positive and
negative voice output
Comment
1. If unused, keep
these pins open.
2. Integrate a
Class- AB
amplifier
internally.
3. Support both
voice and
ringtone output.
Network Status Indicator
PIN Name
PIN No.
I/O
Description
DC Characteristics
Comment
If unused, keep
this pin open.
47
DO
Network status
indication
VOHmin=
0.85×VDD_EXT
VOLmax=
0.15×VDD_EXT
PIN Name
PIN No.
I/O
Description
DC Characteristics
Comment
TXD
34
DO
Transmit data
VILmin=0V
If only TXD, RXD
NETLIGHT
UART Port
MC20_Hardware_Design
Confidential / Released
22 / 95
GSM/GPRS/GNSS Module Series
MC20 Hardware Design
RXD
33
DI
Receive data
DTR
37
DI
Data terminal ready
RI
35
DO
Ring indication
DCD
36
DO
Data carrier detection
CTS
38
DO
Clear to send
RTS
39
DI
Request to send
PIN Name
PIN No.
I/O
Description
DBG_
TXD
29
DO
Transmit data
DBG_
RXD
30
DI
Receive data
VILmax=
0.25×VDD_EXT
VIHmin=
0.75×VDD_EXT
VIHmax=
VDD_EXT+0.2
VOHmin=
0.85×VDD_EXT
VOLmax=
0.15×VDD_EXT
and GND are
used for
communication, it
is recommended
to keep all other
pins open.
DC Characteristics
Comment
The same as UART
port
If unused, keep
these pins open.
DC Characteristics
Comment
The same as UART
port
Refer to Chapter
3.6.3
DC Characteristics
Comment
VOLmax=0.42V
VOHmin=2.4V
VOHnom=2.8V
VILmin=-0.3V
VILmax=0.7V
VIHmin=2.1V
VIHmax=3.1V
Refer to Chapter
3.6.3
Debug Port
Auxiliary UART Port
PIN Name
PIN No.
I/O
Description
TXD_
AUX
25
DO
Transmit data
RXD_
AUX
24
DI
Receive data
GNSS UART Port
PIN Name
PIN No.
I/O
Description
GNSS_
TXD
22
DO
Transmit data
GNSS_
RXD
23
DI
Receive data
PIN No.
I/O
Description
DC Characteristics
Comment
All signals of SIM
interface should
be protected
against ESD with
a TVS diode
array.
SIM Interface
PIN Name
SIM1_ VDD
SIM2_ VDD
18
13
PO
Power supply for SIM
card
The voltage can be
selected by software
automatically. Either
1.8V or 3.0V.
SIM1_ CLK
SIM2_ CLK
19
10
DO
SIM clock
VOLmax=
0.15×SIM_VDD
MC20_Hardware_Design
Confidential / Released
23 / 95
GSM/GPRS/GNSS Module Series
MC20 Hardware Design
SIM1_
DATA
SIM2_
DATA
21
11
SIM1_ RST
SIM2_ RST
20
12
SIM_
GND
16
SIM1_
PRESENCE
37
IO
DO
VOHmin=
0.85×SIM_VDD
VILmax=
0.25×SIM_VDD
VIHmin=
0.75×SIM_VDD
VOLmax=
0.15×SIM_VDD
VOHmin=
0.85×SIM_VDD
SIM data
Maximum trace
length is 200mm
from the module
pad to SIM card
holder.
VOLmax=
0.15×SIM_VDD
VOHmin=
0.85×SIM_VDD
SIM reset
SIM ground
SIM1 card detection
VILmin =0V
VILmax =
0.25×VDD_EXT
VIHmin =
0.75×VDD_EXT
VIHmax =
VDD_EXT+0.2
I/O
Description
DC Characteristics
Comment
AI
General purpose
analog to digital
converter.
Voltage range:
0V to 2.8V
If unused, keep
this pin open.
ADC
PIN Name
ADC
PIN No.
Digital Audio Interface (PCM)
PCM_CLK
59
DO
PCM clock
PCM_OUT
60
DO
PCM data output
PCM_SYNC
61
DO
PCM frame
synchronization
PCM_IN
62
DI
PCM data input
If unused, keep
these pins open
SD Card Interface
SD_CMD
DO
SD Command line
SD_CLK
DO
SD clock
SD_DATA
IO
SD data line
MC20_Hardware_Design
If unused, keep
these pins open
Confidential / Released
24 / 95
GSM/GPRS/GNSS Module Series
MC20 Hardware Design
Antenna Interface
PIN Name
PIN No.
I/O
Description
DC Characteristics
Comment
RF_
ANT
41
IO
GSM antenna pad
Impedance of 50Ω
BT_
ANT
32
IO
BT antenna pad
Impedance of 50Ω
GNSS_
ANT
15
GNSS signal input
Impedance of 50Ω
I/O
Description
DC Characteristics
Comment
VOHmin=
0.85×VDD_EXT
VOLmax=
0.15×VDD_EXT
Refer to
Chapter 3.3.3.2
in all-in-one
solution.
Keep this pin
open in
If unused, keep
this pin open.
Other Interface
PIN Name
GNSS_
VCC_EN
PIN No.
28
GNSS power enabled
stand-alone
solution.
RESERVED
17, 46
55, 56,
57, 58,
63, 64,
65, 66,
67, 68,
Keep these pins
open
Table 7: Multiplexed Functions
PIN Name
PIN No.
Function After Reset
Alternate Function
DTR/SIM1_PRESENCE
37
DTR
SIM1_PRESENCE
3.2. Application Modes Introduction
MC20 module integrates both GSM and GNSS engines which can work as a whole (all-in-one solution)
unit or work relatively independent (stand-alone solution) according to customer demands.
All-in-one solution allows for convenient communication between GSM and GNSS parts. The commands
and data (e.g. AT and PMTK commands, NMEA sentences output, etc.) in both GSM and GNSS parts are
MC20_Hardware_Design
Confidential / Released
25 / 95
GSM/GPRS/GNSS Module Series
MC20 Hardware Design
transmitted through UART port, thus realizing communication between the module and the MCU.
In stand-alone solution, GSM data and AT commands are transmitted through UART port; while GNSS
data such as PMTK command and NMEA sentences output are transmitted through GNSS UART port.
The hardware difference between all-in-one solution and stand-alone solution mainly lies in the
connection method of UART, UART_AUX, and GNSS_UART. The corresponding schematic diagrams are
shown below.
Figure 3: All-in-one Solution Schematic Diagram
Figure 4: Stand-alone Solution Schematic Diagram
MC20_Hardware_Design
Confidential / Released
26 / 95
GSM/GPRS/GNSS Module Series
MC20 Hardware Design
NOTE
In order to ensure the normal operation of GNSS part, please don't power off the GSM part.
Table 8: Comparison between All-in-one and Stand-alone Solution
All-in-one.
Stand-alone
Remarks
Firmware upgrade via
UART Port (GSM and
GNSS Parts share the
same firmware package)
Firmware upgrade via
UART Port (GSM and
GNSS Parts share the
same firmware package)
Refer to Chapter
3.6.1.3 for details
Data transmission
Both GSM and GNSS data
are transmitted through
the GSM UART Port
GSM data is transmitted
through the GSM UART
Port.
GNSS data is transmitted
through the GNSS UART
Port.
GNSS wake up GSM
GNSS can wake up GSM
by interrupts
N/A
GNSS’s
EPO
download
EPO data is downloaded
directly through the GSM
part.
MCU receives the EPO
data which is downloaded
through the GSM part, and
then transmit it to the
GNSS part.
Firmware upgrade
data
Refer to Chapter
3.13 for details
3.3. Power Supply
3.3.1. Power Features
The power supply of the GSM part is one of the key issues in MC20 module design. Due to the 577us
radio burst in GSM part every 4.615ms, the power supply must be able to deliver high current peaks in a
burst period. During these peaks, drops on the supply voltage must not exceed the minimum working
voltage of the GSM part.
The maximum current consumption of GSM part could reach 1.6A during a burst transmission. It will
cause a large voltage drop on the VBAT. In order to ensure stable operation of the part, it is
recommended that the maximum voltage drop during the burst transmission does not exceed 400mV.
MC20_Hardware_Design
Confidential / Released
27 / 95
GSM/GPRS/GNSS Module Series
MC20 Hardware Design
Figure 5: Voltage Ripple during Transmitting (GSM Part)
The power supply for GNSS part is controlled by the GSM part through AT command control over
GNSS_VCC_EN pin.
3.3.2. Decrease Supply Voltage Drop
3.3.2.1. Decrease Supply Voltage Drop for GSM Part
Power supply range of the GSM part is from 3.3V to 4.6V. Make sure that the input voltage will never drop
below 3.3V even in a burst transmission. If the power voltage drops below 3.3V, the module will be turned
off automatically. For better power performance, it is recommended to place a 100uF tantalum capacitor
with low ESR (ESR=0.7Ω) and ceramic capacitors 100nF, 33pF and 10pF near the VBAT pin. A reference
circuit is illustrated in the following figure.
The VBAT trace should be wide enough to ensure that there is not too much voltage drop during burst
transmission. The width of trace should be no less than 2mm; and in principle, the longer the VBAT trace,
the wider it will be.
MC20_Hardware_Design
Confidential / Released
28 / 95
GSM/GPRS/GNSS Module Series
MC20 Hardware Design
Figure 6: Reference Circuit for the VBAT Input (GSM Part)
3.3.2.2. Decrease Supply Voltage Drop for GNSS Part
Power supply range of GNSS part is from 2.8 to 4.3V. GNSS_VCC’s maximum average current is 40mA
during GNSS acquisition after power up. So it is important to supply sufficient current and make the power
clean and stable. The decouple combination of 10uF and 100nF capacitor is recommended nearby
GNSS_VCC pin. A reference circuit is illustrated in the following figure.
Figure 7: Reference Circuit for the GNSS_VCC Input
MC20_Hardware_Design
Confidential / Released
29 / 95
GSM/GPRS/GNSS Module Series
MC20 Hardware Design
3.3.3. Reference Design for Power Supply
3.3.3.1. Reference Design for Power Supply of GSM Part
The power supply of GSM part is capable of providing sufficient current up to 2A at least. If the voltage
drop between the input and output is not too high, it is suggested to use a LDO as the GSM part’s power
supply. If there is a big voltage difference between the input source and the desired output (VBAT), a
switcher power converter is recommended to be used as the power supply.
The following figure shows a reference design for +5V input power source for GSM part. The designed
output for the power supply is 4.0V and the maximum load current is 3A. In addition, in order to get a
stable output voltage, a zener diode is placed close to the pins of VBAT. As to the zener diode, it is
suggested to use a zener diode whose reverse zener voltage is 5.1V and dissipation power is more than 1
Watt.
Figure 8: Reference Circuit for Power Supply of the GSM Part
NOTE
It is suggested to control the module’s main power supply (VBAT) via LDO enable pin to restart the
module when the module becomes abnormal. Power switch circuit like P-channel MOSFET switch circuit
can also be used to control VBAT.
MC20_Hardware_Design
Confidential / Released
30 / 95
GSM/GPRS/GNSS Module Series
MC20 Hardware Design
3.3.3.2. Reference Design for Power Supply of GNSS Part
The power supply for GNSS part is controlled by the GSM part through AT command control over
GNSS_VCC_EN pin.
A reference circuit for the GNSS part power supply is given below. Please pay attention to the electrical
characteristics of GNSS_VCC_EN to match LDO’s EN pin. Please refer to document [1] for details about
the AT commands for GNSS control.
Figure 9: Reference Circuit Design for GNSS Part
3.3.4. Monitor Power Supply
The command AT+CBC can be used to monitor the supply voltage of the GSM part. The unit of the
displayed voltage is mV.
For details, please refer to document [1].
3.3.5. Backup Domain of GNSS
The GNSS part of MC20 module features a backup domain which contains all the necessary GNSS
information for quick start-up and a small amount of user configuration variables. In GNSS’s backup mode,
the backup domain is still alive. As long as the backup domain is alive, EASY technology will be available.
As the GNSS’s backup domain is powered by VBAT, the GNSS’s backup mode will be active as long as
the following conditions are satisfied at the same time:
MC20_Hardware_Design
Confidential / Released
31 / 95
GSM/GPRS/GNSS Module Series
MC20 Hardware Design


The main power supply (VBAT) is remained
The GSM part is powered on

The GNSS part is turned off by AT+QGNSSC=0 command via UART
In this case, the VRTC pin can be kept floating. A reference schematic diagram is shown below.
Figure 10: Internal GNSS’s Backup Domain Power Construction
3.4. Operating Modes
3.4.1. Operating Modes of GSM Part
The table below briefly summarizes the various operating modes of GSM part mentioned in the following
chapters.
Table 9: Operating Modes Overview of GSM Part
Modes
Function
GSM/GPRS
Sleep
After enabling sleep mode by AT+QSCLK=1, the GSM part will
automatically enter into Sleep Mode if DTR is set to high level
and there is no interrupt (such as GPIO interrupt or data on
UART port). In this case, the current consumption of the GSM
part will reduce to the minimal level.
During Sleep Mode, the GSM part can still receive paging
message and SMS from the system normally.
GSM IDLE
Software is active. The GSM part has registered on GSM
network, and it is ready to send and receive GSM data.
GSM TALK
GSM connection is ongoing. In this mode, the power
consumption is decided by the configuration of Power Control
Level (PCL), dynamic DTX control and the working RF band.
GSM Normal
Operation
MC20_Hardware_Design
Confidential / Released
32 / 95
GSM/GPRS/GNSS Module Series
MC20 Hardware Design
GPRS IDLE
The GSM part is not registered on GPRS network. It is not
reachable through GPRS channel.
GPRS
STANDBY
The GSM part is registered on GPRS network, but no GPRS
PDP context is active. The SGSN knows the Routing Area
where the module is located at.
GPRS READY
The PDP context is active, but no data transfer is ongoing. The
GSM part is ready to receive or send GPRS data. The SGSN
knows the cell where the module is located at.
GPRS DATA
There is GPRS data in transfer. In this mode, power
consumption is decided by the PCL, working RF band and
GPRS multi-slot configuration.
POWER DOWN
Normal shutdown by sending the AT+QPOWD=1 command or using the
PWRKEY pin. The power management ASIC disconnects the power supply from
the base band part of the GSM part. Software is not active. The UART interfaces
are not accessible. Operating voltage (connected to VBAT) remains applied.
Minimum
Functionality Mode
(without removing
power supply)
AT+CFUN command can set the GSM part to a minimum functionality mode
without removing the power supply. In this case, the RF part of the GSM part will
not work or the SIM card will not be accessible, or both RF part and SIM card will
be disabled; but the UART port is still accessible. The power consumption in this
case is very low.
Based on system requirements, there are several actions to drive the GSM part to enter into low current
consumption status. For example, AT+CFUN can be used to set the part into minimum functionality mode,
and DTR hardware interface signal can be used to lead the system to Sleep Mode.
3.4.1.1. Minimum Functionality Mode
Minimum functionality mode reduces the functionality of the GSM part to a minimum level. The
consumption of the current can be minimized when the slow clocking mode is activated at the same time.
The mode is set via the AT+CFUN command which provides the choice of the functionality levels
=0, 1, 4.



0: minimum functionality
1: full functionality (default)
4: disable from both transmitting and receiving RF signals
If the GSM part is set to minimum functionality by AT+CFUN=0, the RF function and SIM card function
would be disabled. In this case, the UART port is still accessible, but all AT commands related with RF
function or SIM card function will be unavailable.
If the GSM part is set by the command AT+CFUN=4, the RF function will be disabled, but the UART port
is still active. In this case, all AT commands related with RF function will be unavailable.
MC20_Hardware_Design
Confidential / Released
33 / 95
GSM/GPRS/GNSS Module Series
MC20 Hardware Design
After the GSM part is set by AT+CFUN=0 or AT+CFUN=4, it can return to full functionality mode by
AT+CFUN=1.
For detailed information about AT+CFUN, please refer to document [1].
3.4.1.2. SLEEP Mode
SLEEP mode is disabled by default. It can be enabled by AT+QSCLK=1 and the premise is that the
GNSS is powered off. The default setting is AT+QSCLK=0, and in this mode, the GSM part cannot enter
SLEEP mode.
When the GSM part is set by the command AT+QSCLK=1, you can control the part to enter into or exit
from the SLEEP mode through pin DTR. When DTR is set to high level, and there is no on-air or hardware
interrupt such as GPIO interrupt or data on UART port, the GSM part will enter into SLEEP mode
automatically. In this mode, the GSM part can still receive voice, SMS or GPRS paging from network, but
the UART port does not work.
3.4.1.3. Wake up GSM Part from SLEEP Mode
When the GSM part is in the SLEEP mode, it can be woken up through the following methods:



If the DTR Pin is set low, it would wake up the GSM part from the SLEEP mode. The UART port will
be active within 20ms after DTR is changed to low level.
Receiving a voice or data call from network wakes up the GSM part.
Receiving an SMS from network wakes up the GSM part.
NOTE
DTR pin should be held at low level during communication between the GSM part and the DTE.
3.4.2. Operating Modes of GNSS Part
3.4.2.1. Full on Mode
Full on mode includes tracking mode and acquisition mode. Acquisition mode is defined as that the GNSS
part starts to search satellites, and to determine the visible satellites, coarse carrier frequency & code
phase of satellite signals. When the acquisition is completed, it switches to tracking mode automatically.
Tracking mode is defined as that the GNSS part tracks satellites and demodulates the navigation data
MC20_Hardware_Design
Confidential / Released
34 / 95
GSM/GPRS/GNSS Module Series
MC20 Hardware Design
from specific satellites.
When the GNSS_VCC is valid, the GNSS part will enter into full on mode automatically. The following
table describes the default configuration of full on mode.
Table 10: Default Configuration of Full on Mode (GNSS Part)
Item
Configuration
Baud Rate
115200bps
Protocol
NMEA
Update Rate
1Hz
SBAS
Enable
AIC
Enable
LOCUS
Disable
Easy Technology
Enable
GNSS
GPS+BeiDou
Comment
RMC, VTG, GGA, GSA, GSV and GLL
EASY will be disabled automatically when update
rate exceeds 1Hz.
In full on mode, the consumption complies with the following regulations:
When the GNSS part is powered on, the average current will rush to 40mA and last for a few seconds;
then the consumption will be decreased to the acquisition current marked in table 3 and we defined this
state as acquisition state, and also it will last for several minutes until it switches to tracking state
automatically. The consumption in tracking state is less than that in acquisition state. The value is also
listed in table 3.
Sending PMTK commands allows for switching among multiple positioning systems:
 $PMTK353,0,0,0,0,1*2A: search BDS satellites only
 $PMTK353,1,0,0,0,0*2A: search GPS satellites only
 $PMTK353,1,0,0,0,1*2B: search GPS and BDS satellites
NOTE
In all-in-one solution, make sure the GNSS part is powered on before sending these PMTK commands.
MC20_Hardware_Design
Confidential / Released
35 / 95
GSM/GPRS/GNSS Module Series
MC20 Hardware Design
3.4.2.2. Standby Mode
Standby mode is a low-power consumption mode. In standby mode, the internal core and I/O power
domain are still active; but RF and TCXO are powered off, and the GNSS part stops satellites search and
navigation. The way to enter into standby mode is using PMTK commands.
When the GNSS part exits from standby mode, it will use all internal aiding information like GNSS time,
ephemeris, last position, etc., to ensure the fastest possible TTFF in either Hot or Warm start. The typical
current consumption is about 300uA @GNSS_VCC=3.3V in standby mode.
Sending the following PMTK command can make GNSS part enter into standby mode:
 $PMTK161,0*28: make sure the GNSS part is powered on before sending the command in
all-in-one solution.
The following methods will make GNSS part exit from standby mode:


Sending any data via UART will make GNSS part exit from standby mode in all-in-one solution.
Sending any data via GNSS_UART will make GNSS part exit from standby mode in stand-alone
solution.
3.4.2.3. Backup Mode
Backup mode requires lower power consumption than standby mode. In this mode, the GNSS part stops
acquiring and tracking satellites, but the backed-up memory in backup domain which contains all the
necessary GNSS information for quick start-up and a small amount of user configuration variables is alive.
As long as the backup domain is alive, EASY technology is available. The current consumption in this
mode is about 14uA.
The following method will make GNSS part enter into backup mode:

When VBAT is kept powered and the GSM part is powered on, sending AT+QGNSSC=0 will make
GNSS part enter into backup mode from full on mode.
The following method will make GNSS part exit from backup mode:

Sending AT+QGNSSC=1 via UART, the GNSS part will exit from backup mode and enter full on
mode immediately.
NOTE
In order to enable GNSS part working in backup mode, please make sure the GSM part is powered on.
MC20_Hardware_Design
Confidential / Released
36 / 95
GSM/GPRS/GNSS Module Series
MC20 Hardware Design
3.4.3. Summary of GSM and GNSS Parts’ State in All-in-one Solution
Table 11: Combination States of GSM and GNSS Parts in All-in-one Solution
GSM Part Modes
GNSS Part Modes
Full on
Standby
Backup
Normal



Sleep



Minimum Functionality



3.4.4. Summary of GSM and GNSS Parts’ State in Stand-alone Solution
Table 12: Combination States of GSM and GNSS Parts in Stand-alone Solution
GSM Part Modes
GNSS Part Modes
Full on
Standby
Backup
Normal



Sleep



Minimum Functionality



NOTES
1.
The mark  means that the Part supports this mode.
2.
In all-in-one solution, all PMTK commands used for the GNSS part should be sent through the GSM
UART after the GNSS part is powered on. Make sure the GSM UART Port is accessible.
3.
In all-in-one solution, when the GSM part is in sleep mode, the GNSS part can work in either standby
or full on mode. However, if NMEA GPS data is needed, the GSM part should be woken up first and
then send the corresponding AT command to get. For detailed AT command information, please refer
to document [1].
In stand-alone solution, all PMTK commands used for the GNSS part or NMEA output can be sent or
received through GNSS UART port when the GSM part is powered on.
4.
MC20_Hardware_Design
Confidential / Released
37 / 95
GSM/GPRS/GNSS Module Series
MC20 Hardware Design
3.5. Power on and down
3.5.1. Power on
The module can be turned on by driving the pin PWRKEY to a low level voltage. An open collector driver
circuit is suggested to control the PWRKEY. A simple reference circuit is illustrated as below.
Figure 11: Turn on the Module with an Open-collector Driver
NOTES
1. MC20 module is set to autobauding mode (AT+IPR=0) by default. In autobauding mode, URC RDY is
not reported to the host controller after the module is powered on. When the module is powered on after
a delay of 4 or 5 seconds, it can receive AT commands. Host controller should first send an AT string in
order that the module can detect baud rate of host controller, and it should continue to send the next AT
string until receiving OK string from the module. Then enter AT+IPR=x;&W to set a fixed baud rate for
the module and save the configuration to flash memory of the module. After these configurations, the
URC RDY would be received from the UART Port of the module every time when the module is
powered on. For more details, refer to the section AT+IPR in document [1].
2. When AT command is responded, it indicates the module is turned on successfully; or else the module
fails to be turned on.
The other way to control the PWRKEY is through a button directly. While pressing the key, electrostatic
strike may generate from the finger, and thus, a TVS component is indispensable to be placed nearby the
button for ESD protection. For the best performance, the TVS component must be placed nearby the
button. A reference circuit is shown in the following figure.
MC20_Hardware_Design
Confidential / Released
38 / 95
GSM/GPRS/GNSS Module Series
MC20 Hardware Design
Figure 12: Turn on the Module with a Button
Command AT+QGNSSC=1 should be sent to enable the GNSS power supply after the GSM part is
running. When the GNSS_VCC is valid, the GNSS will enter into full on mode automatically. The turn-on
timing is illustrated in the following figure.
Figure 13: Turn-on Timing
MC20_Hardware_Design
Confidential / Released
39 / 95
GSM/GPRS/GNSS Module Series
MC20 Hardware Design
NOTE
Make sure that VBAT is stable before pulling down PWRKEY pin. The time of T1 is recommended to be
100ms.
3.5.2. Power down
The following procedures can be used to turn off the module:

Normal power down procedure: Turn off module using the PWRKEY pin


Normal power down procedure: Turn off module using command AT+QPOWD
Under-voltage automatic shutdown: Take effect when under-voltage is detected.
3.5.2.1. Power down Module Using the PWRKEY Pin
It is a safe way to turn off the module by driving the PWRKEY to a low level voltage for a certain time. The
power down scenario is illustrated in the following figure.
The power down procedure causes the module to log off from the network and allows the firmware to
save important data before completely disconnecting the power supply.
Before the completion of the power down procedure, the module sends out the result code shown below:
NORMAL POWER DOWN
NOTES
1.
2.
When unsolicited result codes do not appear when autobauding is active and DTE & DCE are not
correctly synchronized after start-up, the module is recommended to be set to a fixed baud rate.
As network logout time is related to the local mobile network, it is recommended to delay about 12
seconds before disconnecting the power supply or restarting the module.
After that moment, no further AT commands can be executed. Then the module enters the power down
mode.
MC20_Hardware_Design
Confidential / Released
40 / 95
GSM/GPRS/GNSS Module Series
MC20 Hardware Design
Figure 14: Turn-off Timing by Using the PWRKEY Pin
3.5.2.2. Power down Module Using AT Command
It is also a safe way to turn off the module via AT command AT+QPOWD=1. This command will let the
module log off from the network and allow the firmware to save important data before completely
disconnecting the power supply.
Before the completion of the power down procedure, the module sends out the result code shown below:
NORMAL POWER DOWN
After that moment, no further AT commands can be executed. And then the module enters into the power
down mode.
Please refer to document [1] for details about the AT command AT+QPOWD.
MC20_Hardware_Design
Confidential / Released
41 / 95
GSM/GPRS/GNSS Module Series
MC20 Hardware Design
3.5.2.3. Power down GNSS Part Alone Using AT Command
It is a safe way to turn off the GNSS part alone via AT command AT+QGNSSC=0. The power down
scenario for GNSS part is illustrated in the following figure.
Figure 15: Turn-off Timing of GNSS Part by Using AT Command
3.5.2.4. Under-voltage Automatic Shutdown
The module will constantly monitor the voltage applied on the VBAT. If the voltage is ≤3.5V, the following
URC will be presented:
UNDER_VOLTAGE WARNING
The normal input voltage range is from 3.3V to 4.6V. If the voltage is <3.3V, the module will automatically
shut down.
If the voltage is <3.3V, the following URC will be presented:
MC20_Hardware_Design
Confidential / Released
42 / 95
GSM/GPRS/GNSS Module Series
MC20 Hardware Design
UNDER_VOLTAGE POWER DOWN
After that moment, no further AT commands can be executed. The module logs off from network and
enters into power down mode.
NOTE
When unsolicited result codes do not appear when autobauding is active and DTE & DCE are not
correctly synchronized after start-up, the module is recommended to be set to a fixed baud rate.
3.6. Serial Interfaces
The module provides four serial ports: UART Port, Debug Port, Auxiliary UART Port and GNSS UART
Port. The module is designed as DCE (Data Communication Equipment), following the traditional
DCE-DTE (Data Terminal Equipment) connection. Autobauding function supports baud rate from
4800bps to 115200bps.
The UART Port:







TXD: Send data to RXD of DTE.
RXD: Receive data from TXD of DTE.
RTS: Request to send.
CTS: Clear to send.
DTR: DTE is ready and inform DCE (this pin can wake the module up).
RI: Ring indicator (when there is a call, SMS or URC output, the module will inform DTE with the RI
pin).
DCD: Data carrier detection (the validity of this pin demonstrates successful set-up of the
communication link).
The Debug Port:


DBG_TXD: Send data to the COM port of peripheral.
DBG_RXD: Receive data from the COM port of peripheral.
The Auxiliary UART Port:

In all-in-one solution:
TXD_AUX: Send data to the GNSS part.
RXD_AUX: Receive data from the GNSS part.

In stand-alone solution:
TXD_AUX: Keep open except during firmware upgrade.
MC20_Hardware_Design
Confidential / Released
43 / 95
GSM/GPRS/GNSS Module Series
MC20 Hardware Design
RXD_AUX: Keep open except during firmware upgrade.
The GNSS UART Port

In all-in-one solution:
GNSS_TXD: Send data to the GSM part.
GNSS_RXD: Receive data from the GSM part.

In stand-alone solution:
GNSS_TXD: Send GNSS data to the COM port of peripheral.
GNSS_RXD: Receive GNSS data from the COM port of peripheral.
The logic levels are described in the following table.
Table 13: Logic Levels of the UART Interface
Parameter
Min.
Max.
Unit
VIL
0.25×VDD_EXT
VIH
0.75×VDD_EXT
VDD_EXT +0.2
VOL
0.15×VDD_EXT
VOH
0.85×VDD_EXT
VDD_EXT
Pin No.
Description
Table 14: Pin Definition of the UART Interfaces
Interface
UART Port
Debug Port
MC20_Hardware_Design
Pin Name
TXD
34
Transmit data
RXD
33
Receive data
DTR
37
Data terminal ready
RI
35
Ring indication
DCD
36
Data carrier detection
CTS
38
Clear to send
RTS
39
Request to send
DBG_RXD
30
Receive data
Confidential / Released
44 / 95
GSM/GPRS/GNSS Module Series
MC20 Hardware Design
Auxiliary UART Port1)
DBG_TXD
29
Transmit data
RXD_AUX1)
24
Receive data
TXD_AUX1)
25
Transmit data
GNSS_RXD
23
Receive data
GNSS_TXD
22
Transmit data
GNSS UART Port
NOTE
1)
It is recommended to keep these pins open in stand-alone solution, except during firmware upgrade.
3.6.1. UART Port
3.6.1.1. Features of UART Port






Seven lines on UART interface
Contain data lines TXD and RXD, hardware flow control lines RTS and CTS, as well as other control
lines DTR, DCD and RI.
Used for AT command, GPRS data, etc. Multiplexing function is supported on the UART Port. NMEA
output and PMTK command can be supported in all-in-one solution.
Support the following communication baud rates:
300, 600, 1200, 2400, 4800, 9600, 14400, 19200, 28800, 38400, 57600, 115200bps.
The default setting is autobauding mode. Support the following baud rates for autobauding function:
4800, 9600, 19200, 38400, 57600, 115200bps.
Hardware flow control is disabled by default. When hardware flow control is required, RTS and CTS
should be connected to the host. AT command AT+IFC=2,2 is used to enable hardware flow control.
AT command AT+IFC=0,0 is used to disable the hardware flow control. For more details, please refer
to document [1].
After setting a fixed baud rate or autobauding, please send “AT” string at that rate. The UART port is
ready when it responds “OK”.
Autobauding allows the module to detect the baud rate by receiving the string “AT” or “at” from the host or
PC automatically, which gives module flexibility without considering which baud rate is used by the host
controller. Autobauding is enabled by default. To take advantage of the autobauding mode, special
attention should be paid according to the following requirements:
MC20_Hardware_Design
Confidential / Released
45 / 95
GSM/GPRS/GNSS Module Series
MC20 Hardware Design
Synchronization between DTE and DCE:
When DCE (the module) is powered on with autobauding enabled, it is recommended to wait 2 to 3
seconds before sending the first AT character. After receiving the “OK” response, DTE and DCE are
correctly synchronized.
If the host controller needs URC in the mode of autobauding, it must be synchronized firstly. Otherwise
the URC will be discarded.
Restrictions on autobauding operation:

The UART port has to be operated at 8 data bits, no parity and 1 stop bit (factory setting).




The “At” and “aT” commands cannot be used.
Only the strings “AT” or “at” can be detected (neither “At” nor “aT”).
The Unsolicited Result Codes like RDY, +CFUN: 1 and +CPIN: READY will not be indicated when
the module is turned on with autobauding enabled and not be synchronized.
Any other Unsolicited Result Codes will be sent at the previous baud rate before the module detects


the new baud rate by receiving the first “AT” or “at” string. The DTE may receive unknown characters
after switching to a new baud rate.
It is not recommended to switch to autobauding from a fixed baud rate.
If autobauding is active it is not recommended to switch to multiplex mode.
NOTE
To assure reliable communication and avoid any problems caused by undetermined baud rate between
DCE and DTE, it is strongly recommended to configure a fixed baud rate and save it instead of using
autobauding after start-up. For more details, please refer to the Section AT+IPR in document [1].
3.6.1.2. The Connection of UART
The connection between module and host using UART Port is very flexible. Three connection styles are
illustrated as below.
A reference design for Full-Function UART connection is shown as below when it is applied in
modulation-demodulation.
MC20_Hardware_Design
Confidential / Released
46 / 95
GSM/GPRS/GNSS Module Series
MC20 Hardware Design
Figure 16: Reference Design for Full-Function UART
Three-line connection is shown as below.
Figure 17: Reference Design for UART Port (Three Line Connection)
A reference design for UART Port with hardware flow control is shown as below. The connection will
enhance the reliability of the mass data communication.
MC20_Hardware_Design
Confidential / Released
47 / 95
GSM/GPRS/GNSS Module Series
MC20 Hardware Design
Figure 18: Reference Design for UART Port with Hardware Flow Control
3.6.1.3. Firmware Upgrade
TXD and RXD can be used for firmware upgrade in both all-in-one solution and stand-alone solution.
The PWRKEY pin must be pulled down before firmware upgrade. A reference circuit is shown as below:
Figure 19: Reference Design for Firmware Upgrade
NOTES
1.
2.
In stand-alone solution, make sure the Auxiliary UART Port is connected to the GNSS UART Port
during firmware upgrade. Please refer to Chapter 3.6.3.2 for details.
The firmware of module might need to be upgraded due to a certain reasons. It is thus recommended
to reserve these pins in the host board for firmware upgrade.
MC20_Hardware_Design
Confidential / Released
48 / 95
GSM/GPRS/GNSS Module Series
MC20 Hardware Design
3.6.2. Debug Port



Two lines: DBG_TXD and DBG_RXD.
The port outputs log information automatically.
Debug Port is only used for firmware debugging and its baud rate must be configured as 460800bps.
Figure 20: Reference Design for Debug Port
3.6.3. Auxiliary UART Port and GNSS UART Port
3.6.3.1. Connection in All-in-one Solution
In all-in-one solution, the Auxiliary UART Port and GNSS UART Port should be connected together, thus
allowing for communication between GSM and GNSS parts. A reference design is shown below.
MC20_Hardware_Design
Confidential / Released
49 / 95
GSM/GPRS/GNSS Module Series
MC20 Hardware Design
Figure 21: Auxiliary and GNSS UART Port Connection in All-in-one Solution
NOTE
As the GNSS part of MC20 module outputs more data than a single GNSS system, the default output
NMEA types running in 4800bps baud rate and 1Hz update rate will lose some data. The solution to avoid
losing data in 4800bps baud rate and 1Hz update rate is to decrease the output NMEA types. 115200bps
baud rate is enough to transmit GNSS NMEA in default settings and it is thus recommended.
3.6.3.2. Connection in Stand-alone Solution
In stand-alone solution, the GNSS UART Port is connected to the COM port of peripheral. During
firmware upgrade, switch S1 should be kept closed. Otherwise, it should be kept open. A reference design
is shown below.
MC20_Hardware_Design
Confidential / Released
50 / 95
GSM/GPRS/GNSS Module Series
MC20 Hardware Design
Figure 22: Auxiliary and GNSS UART Port Connection in Stand-alone Solution
3.6.4. UART Application
A reference design of 3.3V level match is shown as below. If the host is a 3V system, please change the
5.6K resistors to 10K ones.
Figure 23: Level Match Design for 3.3V System
NOTE
It is highly recommended to add the resistor divider circuit on the UART signal lines when the host’s level
is 3V or 3.3V. For a higher voltage level system, a level shifter IC could be used between the host and the
module. For more details about UART circuit design, please refer to document [13].
MC20_Hardware_Design
Confidential / Released
51 / 95
GSM/GPRS/GNSS Module Series
MC20 Hardware Design
The following figure shows a sketch map between the module and the standard RS-232 interface. As the
electrical level of module is 2.8V, a RS-232 level shifter must be used. Note that you should assure the
I/O voltage of level shifter which connects to module is 2.8V.
Figure 24: Sketch Map for RS-232 Interface Match
Please visit vendors’ websites to select a suitable IC, such as: http://www.maximintegrated.com and
http://www.exar.com/.
3.7. Audio Interfaces
The module provides one analog input channel and two analog output channels.
Table 15: Pin Definition of Audio Interface
Interface
Pin Name
Pin No.
Description
MICP
Microphone positive input
MICN
Microphone negative input
AIN/AOUT1
MC20_Hardware_Design
Confidential / Released
52 / 95
GSM/GPRS/GNSS Module Series
MC20 Hardware Design
SPKP
Channel 1 Audio positive output
SPKN
Channel 1 Audio negative output
MICP
Microphone positive input
MICN
Microphone negative input
LOUDSPKP
54
Channel 2 Audio positive output
LOUDSPKN
53
Channel 2 Audio negative output
AIN/AOUT2
AIN can be used for input of microphone and line. An electret microphone is usually used. AIN are
differential input channels.
AOUT1 is used for output of receiver. The channel is typically used for building a receiver into a handset.
AOUT1 channel is a differential channel.
AOUT2 is used for loudspeaker output as it is embedded with an amplifier of class AB whose maximum
drive power is 800mW. AOUT2 is a differential channel.
AOUT2 also can be used for output of earphone, and can be used as a single-ended channel.
All these audio channels support voice and ringtone output, and so on, and can be switched by
AT+QAUDCH command. For more details, please refer to document [1].
Use AT command AT+QAUDCH to select audio channel:



0--AIN/AOUT1, the default value is 0.
1--AIN/AOUT2, this channel is always used for earphone.
2--AIN/AOUT2, this channel is always used for loudspeaker.
For each channel, you can use AT+QMIC to adjust the input gain level of microphone. You can also use
AT+CLVL to adjust the output gain level of receiver and speaker. AT+QSIDET is used to set the
side-tone gain level. For more details, please refer to document [1].
Table 16: AOUT2 Output Characteristics
Item
Condition
RMS Power
8ohm load
VBAT=3.7v
THD+N=1%
MC20_Hardware_Design
Min.
Typ.
800
Confidential / Released
Max.
Unit
mW
53 / 95
GSM/GPRS/GNSS Module Series
MC20 Hardware Design
3.7.1. Decrease TDD Noise and Other Noises
The 33pF capacitor is applied for filtering out 900MHz RF interference when the module is transmitting at
EGSM900MHz. Without placing this capacitor, TDD noise could be heard. Moreover, the 10pF capacitor
here is used for filtering out 1800MHz RF interference. However, the resonant frequency point of a
capacitor largely depends on the material and production technique. Therefore, customers would have to
discuss with their capacitor vendors to choose the most suitable capacitor for filtering out GSM850MHz,
EGSM900MHz, DCS1800MHz and PCS1900MHz separately.
The severity degree of the RF interference in the voice channel during GSM transmitting period largely
depends on the application design. In some cases, EGSM900 TDD noise is more severe; while in other
cases, DCS1800 TDD noise is more obvious. Therefore, you can have a choice based on test results.
Sometimes, even no RF filtering capacitor is required.
The capacitor which is used for filtering out RF noise should be close to the audio interface. Audio
alignment should be as short as possible.
In order to decrease radio or other signal interference, the position of RF antenna should be kept away
from audio interface and audio alignment. Power alignment and audio alignment should not be parallel,
and power alignment should be far away from audio alignment.
The differential audio traces must be routed according to the differential signal layout rule.
3.7.2. Microphone Interfaces Design
AIN channels come with internal bias supply for external electret microphone. A reference circuit is shown
in the following figure.
Figure 25: Reference Design for AIN
MC20_Hardware_Design
Confidential / Released
54 / 95
GSM/GPRS/GNSS Module Series
MC20 Hardware Design
3.7.3. Receiver and Speaker Interface Design
Figure 26: Handset Interface Design for AOUT1
Figure 27: Speaker Interface Design with an Amplifier for AOUT1
A suitable differential audio amplifier can be chosen from the Texas Instrument’s website
(http://www.ti.com/). There are also other excellent audio amplifier vendors in the market.
MC20_Hardware_Design
Confidential / Released
55 / 95
GSM/GPRS/GNSS Module Series
MC20 Hardware Design
3.7.4. Earphone Interface Design
Figure 28: Earphone Interface Design
3.7.5. Loud Speaker Interface Design
Figure 29: Loud Speaker Interface Design
MC20_Hardware_Design
Confidential / Released
56 / 95
GSM/GPRS/GNSS Module Series
MC20 Hardware Design
3.7.6. Audio Characteristics
Table 17: Typical Electret Microphone Characteristics
Parameter
Min.
Typ.
Max.
Unit
Working Voltage
1.2
1.5
2.0
Working Current
200
500
uA
External Microphone Load Resistance
2.2
K Ohm
Table 18: Typical Speaker Characteristics
Parameter
Min.
Load resistance
Typ.
Max.
32
Unit
Ohm
Single-ended
Reference level
AOUT1
Output
Load resistance
2.4
32
Vpp
Ohm
Differential
Reference level
Load resistance
4.8
Vpp
Ohm
Differential
Reference level
AOUT2
Output
Load resistance
2×VBAT
Vpp
Ohm
Single-ended
Reference level
VBAT
Vpp
3.8. SIM Card Interface
The SIM interface supports the functionality of the GSM Phase 1 specification and also the functionality of
the new GSM Phase 2+ specification for FAST 64 kbps SIM card (intended for use with a SIM application
tool-kit.
The SIM interface is powered by an internal regulator in the module. Both 1.8V and 3.0V SIM cards are
supported, and Dual SIM Single Standby function is supported.
MC20_Hardware_Design
Confidential / Released
57 / 95
GSM/GPRS/GNSS Module Series
MC20 Hardware Design
Table 19: Pin Definition of the SIM Interface
Pin Name
Pin No.
Description
SIM1_VDD
18
Supply power for SIM card. Automatic detection of
SIM1 card voltage. 3.0V±5% and 1.8V±5%.
Maximum supply current is around 10mA.
SIM1_CLK
19
SIM1 card clock.
SIM1_DATA
21
SIM1 card data I/O.
SIM1_RST
20
SIM1 card reset.
SIM1_PRESENCE
37
SIM1 card detection.
SIM_GND
16
SIM card ground.
SIM2_VDD
13
Supply power for SIM card. Automatic detection of
SIM2 card voltage. 3.0V±5% and 1.8V±5%.
Maximum supply current is around 10mA.
SIM2_CLK
10
SIM2 card clock.
SIM2_DATA
11
SIM2 card data I/O.
SIM2_RST
12
SIM2 card reset.
Alternate
Function1)
DTR
NOTE
1)
If several interfaces share the same I/O pin, to avoid conflict between these alternate functions, only one
peripheral should be enabled at a time.
The following figure is a reference design for SIM1 interface with an 8-pin SIM card holder.
MC20_Hardware_Design
Confidential / Released
58 / 95
GSM/GPRS/GNSS Module Series
MC20 Hardware Design
Figure 30: Reference Circuit for SIM1 Interface with an 8-pin SIM Card Holder
If SIM1 card detection function is not used, keep SIM1_PRESENCE pin open. A reference circuit for a
6-pin SIM card socket is shown in the following figure.
Figure 31: Reference Circuit for SIM1 Interface with a 6-pin SIM Card Holder
The following figure is a reference design for SIM2 interface with a 6-pin SIM card holder.
MC20_Hardware_Design
Confidential / Released
59 / 95
GSM/GPRS/GNSS Module Series
MC20 Hardware Design
Figure 32: Reference Circuit for SIM2 Interface with a 6-pin SIM Card Holder
For more information
http://www.molex.com/.
of
SIM
card
holder,
you
can
visit
http://www.amphenol.com/
and
In order to enhance the reliability and availability of the SIM card in application, please conform to the
following criteria in the SIM circuit design:






Keep layout of SIM card as close to the module as possible. Assure the trace length is less than
200mm.
Keep SIM card signal away from RF and VBAT alignment.
Assure the ground between module and SIM holder short and wide. Keep the width of ground no less
than 0.5mm to maintain the same electric potential. The decouple capacitor of SIM_VDD is less than
1uF and must be near to SIM holder.
To avoid cross talk between SIM_DATA and SIM_CLK, keep them away from each other and shield
them with surrounded ground.
In order to offer good ESD protection, it is recommended to add a TVS diode array. For more
information of TVS diode, please visit http://www.onsemi.com/. The most important rule is to place
the ESD protection device close to the SIM card socket and make sure the nets being protected will
go through the ESD device first and then lead to module. The 22Ω resistors should be connected in
series between the module and the SIM card so as to suppress the EMI spurious transmission and
enhance the ESD protection. Please note that the SIM peripheral circuit should be close to the SIM
card socket.
Place the RF bypass capacitors (33pF) close to the SIM card on all signals lines to improve EMI
suppression performance.
MC20_Hardware_Design
Confidential / Released
60 / 95
GSM/GPRS/GNSS Module Series
MC20 Hardware Design
3.9. ADC
The module provides an ADC channel to measure the value of voltage. Please give priority to the use of
ADC0 channel. Command AT+QADC can read the voltage value applied on ADC0 pin. For details of this
AT command, please refer to document [1]. In order to improve the accuracy of ADC, the layout of ADC
should be surrounded by ground.
Table 20: Pin Definition of the ADC
Pin Name
Pin No.
Description
ADC
Analog to digital converter.
Table 21: Characteristics of the ADC
Item
Min.
Voltage Range
Typ.
Max.
Unit
2.8
ADC Resolution
10
bits
ADC Accuracy
2.7
mV
3.10. Behaviors of the RI
Table 22: Behaviors of the RI
State
RI Response
Standby
HIGH
Voice Call
Change to LOW, and then:
1. Change to HIGH when call is established.
2. Change to HIGH when use ATH to hang up the call
3. Change to HIGH first when calling part hangs up and then change to LOW for
120ms indicating “NO CARRIER” as an URC. After that, RI changes to HIGH
again.
4. Change to HIGH when SMS is received.
SMS
When a new SMS comes, the RI changes to LOW and holds low level for about
120ms, and then changes to HIGH.
MC20_Hardware_Design
Confidential / Released
61 / 95
GSM/GPRS/GNSS Module Series
MC20 Hardware Design
URC
Certain URCs can trigger 120ms low level on RI. For more details, please refer to
document [1]
If the module is used as a caller, the RI would maintain high except when the URC or SMS is received.
When it is used as a receiver, the timing of RI is shown below.
Figure 33: RI Behavior as a Receiver When Voice Calling
Figure 34: RI Behavior as a Caller
Figure 35: RI Behavior When URC or SMS Received
MC20_Hardware_Design
Confidential / Released
62 / 95
GSM/GPRS/GNSS Module Series
MC20 Hardware Design
3.11. Network Status Indication
The NETLIGHT signal can be used to drive a network status indicator LED. The working state of this pin
is listed in the following table.
Table 23: Working State of the NETLIGHT
State
Module Function
Off
The module is not running.
64ms On/800ms Off
The module is not synchronized with network.
64ms On/2000ms Off
The module is synchronized with network.
64ms On/600ms Off
GPRS data transmission after dialing the PPP connection.
A reference circuit is shown as below.
Figure 36: Reference Design for NETLIGHT
MC20_Hardware_Design
Confidential / Released
63 / 95
GSM/GPRS/GNSS Module Series
MC20 Hardware Design
3.12. EASY Autonomous AGPS Technology
Supplying aiding information like ephemeris, almanac, rough last position, time and satellite status, can
help improve the acquisition sensitivity and the TTFF for a module. This is called as EASY technology and
MC20’s GNSS part supports it.
EASY technology works as embedded software which can accelerate TTFF by predicting satellite
navigation messages from received ephemeris. The GNSS part will calculate and predict orbit information
automatically up to 3 days after first receiving the broadcast ephemeris, and save the predicted
information into the internal memory. GNSS part of MC20 will use the information for positioning if no
enough information from satellites, so the function is helpful for positioning and TTFF improvement.
The EASY function can reduce TTFF to 5s in warm start. In this case, GNSS’s backup domain should be
valid. In order to gain enough broadcast ephemeris information from GNSS satellites, the GNSS part
should receive the information for at least 5 minutes in good signal conditions after it fixes the position.
EASY function is enabled by default. Command “$PMTK869,1,0*34” can be used to disable EASY
function. For more details, please refer to document [2].
NOTE
In all-in-one solution, make sure the GNSS part is powered on before sending the PMTK command.
3.13. EPO Offline AGPS Technology
MC20 module features a function called EPO (Extended Prediction Orbit) which is a world leading
technology. When MC20 module is powered on, EPO function can be enabled via AT command
AT+QGNSSEPO=1. When the GSM part detected that the EPO data has expired, the EPO data will be
automatically downloaded to the GSM part’s FS from MTK server via GSM/GPRS network; and the GNSS
part will get the EPO data via build-in GNSS command from GSM's FS when it detected that the local
EPO data has expired. When there is no local EPO data or when the data has expired, MC20 module will
download the data (4KB) for 6 hours’ orbit predictions in order to achieve cold start in the shortest time,
and then continue to download the EPO data (48KB) for 3 days. The technology allows the module to
realize fast positioning. Command AT+QGNSSEPO=0 can turn off the EPO function.
NOTE
Make sure the EPO function is enabled if you need to download the EPO data.
MC20_Hardware_Design
Confidential / Released
64 / 95
GSM/GPRS/GNSS Module Series
MC20 Hardware Design
3.14. Multi-tone AIC
MC20 module has a function called multi-tone AIC (Active Interference Cancellation) to decease
harmonic of RF noise from Wi-Fi, GSM, 3G and 4G.
Up to 12 multi-tone AIC embedded in the module can provide effective narrow-band interference and
jamming elimination. The GNSS signal could be demodulated from the jammed signal, which can ensure
better navigation quality. AIC function is enabled by default. Enabling AIC function will increase current
consumption by about 1mA @VCC=3.3V. The following commands can be used to set AIC function.
Enable AIC function: $PMTK 286,1*23
Disable AIC function: $PMTK 286,0*22
NOTE
In all-in-one solution, make sure the GNSS part is powered on before sending these PMTK commands.
MC20_Hardware_Design
Confidential / Released
65 / 95
GSM/GPRS/GNSS Module Series
MC20 Hardware Design
Antenna Interface
MC20 has three antenna interfaces which are used for GSM antenna, GNSS antenna and BT antenna,
respectively. The Pin 41 is the GSM antenna pad; the Pin 15 is the GNSS antenna pad; and Pin 32 is the
BT antenna pad. The RF interface of the three antenna pads has an impedance of 50Ω.
4.1. GSM Antenna Interface
There is a GSM antenna pad named RF_ANT for MC20.
Table 24: Pin Definition of the RF_ANT
Pin Name
Pin No.
Description
GND
40
Ground
RF_ANT
41
GSM antenna pad
GND
42
Ground
4.1.1. Reference Design
The external antenna must be matched properly to achieve the best performance; so the matching circuit
is necessary. A reference design for GSM antenna is shown below.
Figure 37: Reference Design for GSM Antenna
MC20_Hardware_Design
Confidential / Released
66 / 95
GSM/GPRS/GNSS Module Series
MC20 Hardware Design
MC20 provides an RF antenna pad for antenna connection. The RF trace in host PCB connected to the
module’s RF antenna pad should be coplanar waveguide line or microstrip line, whose characteristic
impedance should be close to 50Ω. MC20 comes with grounding pads which are next to the antenna pad
in order to give a better grounding. Besides, a π type matching circuit is suggested to be used to adjust
the RF performance.
To minimize the loss on RF trace and RF cable, please pay attention to the design. The following table
shows the requirement on GSM antenna.
Table 25: Antenna Cable Requirements
Type
Requirements
GSM850/EGSM900
Cable insertion loss <1dB
DCS1800/PCS1900
Cable insertion loss <1.5dB
Table 26: Antenna Requirements
Type
Requirements
Frequency Range
Depend on the frequency band(s) provided by the network operator
VSWR
≤2
Gain (dBi)
Max. Input Power (W)
50
Input Impedance (Ω)
50
Polarization Type
Vertical
4.1.2. RF Output Power
Table 27: RF Output Power
Frequency
Max.
Min.
GSM850
33dBm±2dB
5dBm±5dB
EGSM900
33dBm±2dB
5dBm±5dB
DCS1800
30dBm±2dB
0dBm±5dB
MC20_Hardware_Design
Confidential / Released
67 / 95
GSM/GPRS/GNSS Module Series
MC20 Hardware Design
PCS1900
30dBm±2dB
0dBm±5dB
NOTE
In GPRS 4 slots TX mode, the maximum output power is reduced by 2.5dB. This design conforms to the
GSM specification as described in section 13.16 of 3GPP TS 51.010-1.
4.1.3. RF Receiving Sensitivity
Table 28: RF Receiving Sensitivity
Frequency
Receive Sensitivity
GSM850
< -110dBm
EGSM900
< -110dBm
DCS1800
< -110dBm
PCS1900
< -110dBm
4.1.4. Operating Frequencies
Table 29: Operating Frequencies
Frequency
Receive
Transmit
ARFCH
GSM850
869~894MHz
824~849MHz
128~251
EGSM900
925~960MHz
880~915MHz
0~124, 975~1023
DCS1800
1805~1880MHz
1710~1785MHz
512~885
PCS1900
1930~1990MHz
1850~1910MHz
512~810
4.1.5. RF Cable Soldering
Soldering the RF cable to RF pad of module correctly will reduce the loss on the path of RF, please refer
to the following example of RF soldering.
MC20_Hardware_Design
Confidential / Released
68 / 95
GSM/GPRS/GNSS Module Series
MC20 Hardware Design
Figure 38: RF Soldering Sample
4.2. GNSS Antenna Interface
The GNSS part of MC20 module supports both GPS and BeiDou systems. The RF signal is obtained from
the GNSS_ANT pin. The impedance of RF trace should be controlled as 50 Ohm, and the trace length
should be kept as short as possible.
4.2.1. Antenna Specifications
The module can be connected to a dedicated GPS/BeiDou passive or active antenna to receive
GPS/BeiDou satellite signals. The recommended antenna specifications are given in the following table.
Table 30: Recommended Antenna Specifications
Antenna Type
Specification
Passive Antenna
GPS frequency: 1575.42±2MHz
BeiDou frequency: 1602±4MHz
VSWR: <2 (Typ.)
Polarization: RHCP or Linear
Gain: >0dBi
Active Antenna
GPS frequency: 1575.42±2MHz
BeiDou frequency:1602±4MHz
VSWR: <2 (Typ.)
Polarization: RHCP or Linear
Noise figure: <1.5dB
MC20_Hardware_Design
Confidential / Released
69 / 95
GSM/GPRS/GNSS Module Series
MC20 Hardware Design
Gain (antenna): >-2dBi
Gain (embedded LNA): 20dB (Typ.)
Total gain: >18dBi (Typ.)
4.2.2. Active Antenna
The following figure is a typical reference design with active antenna. In this mode, the antenna is
powered by GNSS_VCC.
Figure 39: Reference Design with Active Antenna
C1, R1 and C2 are reserved matching circuit for antenna impedance modification. By default, C1 and C2
are not mounted; R1 is 0 ohm.
The external active antenna is powered by GNSS_VCC. The voltage ranges from 2.8V to 4.3V, and the
typical value is 3.3V. If the voltage does not meet the requirements for powering the active antenna, an
external LDO should be used.
The inductor L1 is used to prevent the RF signal from leaking into the GNSS_VCC pin and route the bias
supply to the active antenna, and the recommended value of L1 is no less than 47nH. R2 can protect the
whole circuit in case the active antenna is shorted to ground.
NOTE
In all-in-one solution, please note that the power supply of GNSS_VCC is controlled by the GSM part
through AT command.
MC20_Hardware_Design
Confidential / Released
70 / 95
GSM/GPRS/GNSS Module Series
MC20 Hardware Design
4.2.3. Passive Antenna
Figure 40: Reference Design with Passive Antenna
The above figure is a typical reference design with passive antenna.
C1, R1 and C2 are reserved matching circuit for antenna impedance modification. C1 and C2 are not
mounted by default; R1 is 0 ohm. Impedance of RF trace should be controlled as 50 ohm and the trace
length should be kept as short as possible.
4.3. Bluetooth Antenna Interface
MC20 provides a Bluetooth antenna interface. Bluetooth is a wireless technology that allows devices to
communicate, or transmit data/voice, wirelessly over a short distance. It is described as a short-range
communication technology intended to replace the cables connecting portable and/or fixed devices while
maintaining high level of security. Bluetooth is standardized as IEEE802.15 and operates in the 2.4 GHz
range using RF technology. Its data rate is up to 3Mbps.
MC20 is fully compliant with Bluetooth specification 3.0, and supports profiles including SPP and HFP-AG.
The module provides a Bluetooth antenna pad named BT_ANT, and the pin definition is listed below.
MC20_Hardware_Design
Confidential / Released
71 / 95
GSM/GPRS/GNSS Module Series
MC20 Hardware Design
Table 31: Pin Definition of the BT_ANT
Pin Name
Pin No.
Description
BT_ANT
32
BT antenna pad
GND
31
Ground
The external antenna must be matched properly to achieve the best performance, so the matching circuit
is necessary. The connection is recommended as in the following figure:
0R
BT_ANT
NM
MC20 Module
NM
Figure 41: Reference Design for Bluetooth Antenna
There are some suggestions for component placement and RF trace layout for Bluetooth RF traces:



Antenna matching circuit should be closed to the antenna;
The impedance of RF trace should be controlled as 50Ω;
The RF traces should be kept far away from the high frequency signals and strong disturbing source.
The proposed antenna type is Chip antenna,and the detailed description is as follows:
Table 32: Recommended Antenna Specifications
ITEM
SPECIFICATION
Type
Chip Antenna
Frequency Band
2.40GHz~2.50GHz
MC20_Hardware_Design
Confidential / Released
72 / 95
GSM/GPRS/GNSS Module Series
MC20 Hardware Design
Peak Gain
3 dBi Typ
Impedance
50Ω Typ
MC20_Hardware_Design
Confidential / Released
73 / 95
GSM/GPRS/GNSS Module Series
MC20 Hardware Design
Electrical, Reliability and Radio
Characteristics
5.1. Absolute Maximum Ratings
Absolute maximum ratings for power supply and voltage on digital and analog pins of the module are
listed in the following table:
Table 33: Absolute Maximum Ratings
Parameter
Min.
Max.
Unit
VBAT
-0.3
+4.73
GNSS_VCC
-0.3
+4.5
Peak Current of Power Supply (VBAT)
RMS Current of Power Supply (VBAT, during one
TDMA-frame)
0.7
Voltage at Digital Pins
-0.3
3.08
Voltage at Analog Pins
-0.3
3.08
Voltage at Digital/analog Pins in Power Down Mode
-0.25
0.25
5.2. Operating Temperature
The operating temperature is listed in the following table:
MC20_Hardware_Design
Confidential / Released
74 / 95
GSM/GPRS/GNSS Module Series
MC20 Hardware Design
Table 34: Operating Temperature
Parameter
Min.
Typ.
Max.
Unit
Operation temperature range 1)
-35
+25
+75
℃
Extended temperature range 2)
-40
+85
℃
NOTES
1.
2.
1)
Within operation temperature range, the module is 3GPP compliant.
Within extended temperature range, the module remains the ability to establish and maintain a
voice, SMS, data transmission, emergency call, etc. There is no unrecoverable malfunction. There
are also no effects on radio spectrum and no harm to radio network. Only one or more parameters like
Pout might reduce in their value and exceed the specified tolerances. When the temperature returns to
the normal operating temperature levels, the module will meet 3GPP compliant again.
2)
5.3. Power Supply Ratings
Table 35: Power Supply Ratings of GSM Part (GNSS is Powered off)
Parameter
VBAT
Description
Conditions
Min.
Typ.
Max.
Unit
Supply voltage
Voltage must stay within the
min/max values, including
voltage drop, ripple, and spikes.
3.3
4.0
4.6
Voltage drop
during
transmitting
burst
Maximum power control level
on GSM850 and EGSM900.
400
mV
Power down mode
SLEEP mode @DRX=5
IVBAT
Average supply
current
Minimum functionality mode
AT+CFUN=0
IDLE mode
SLEEP mode
AT+CFUN=4
IDLE mode
SLEEP mode
TALK mode
GSM850/EGSM9001)
DCS1800/PCS19002)
MC20_Hardware_Design
Confidential / Released
220
1.2
uA
mA
13
0.68
mA
mA
13
0.73
mA
mA
208/209
142/146
mA
mA
75 / 95
GSM/GPRS/GNSS Module Series
MC20 Hardware Design
Peak supply
current (during
transmission
slot)
DATA mode, GPRS (3Rx, 2Tx)
GSM850/EGSM9001)
DCS1800/PCS19002)
359/360
232/250
mA
mA
DATA mode, GPRS (2 Rx, 3Tx)
GSM850/EGSM9001)
DCS1800/PCS19002)
431/413
311/339
mA
mA
DATA mode, GPRS (4 Rx, 1Tx)
GSM850/EGSM9001)
DCS1800/PCS19002)
215/153
153/162
mA
mA
DATA mode, GPRS (1Rx, 4Tx)
GSM850/EGSM9001)
DCS1800/PCS19002)
499/4693)
392/427
mA
mA
Maximum power control level
on GSM850 and EGSM900.
1.6
NOTES
1.
2.
3.
1)
Power control level PCL 5.
Power control level PCL 0.
3)
Under the GSM850 and EGSM900 spectrum, the power of 1Rx and 4Tx is reduced.
2)
Table 36: Power Supply Ratings of GNSS Part
Parameter
Description
Conditions
Min.
Typ.
Max.
Unit
GNSS_
VCC
Supply voltage
Voltage must stay
within the min/max
values, including
voltage drop, ripple,
and spikes.
2.8
3.3
4.3
IVCCP1)
Peak supply current
VCC=3.3V
150
mA
NOTE
1)
This figure can be used to determine the maximum current capability of power supply.
MC20_Hardware_Design
Confidential / Released
76 / 95
GSM/GPRS/GNSS Module Series
MC20 Hardware Design
5.4. Current Consumption
Table 37: Current Consumption of GSM Part (GNSS is Powered off)
Condition
Current Consumption
Voice Call
GSM850
@power level #5 <300mA, Typical 174mA
@power level #12, Typical 83mA
@power level #19, Typical 62mA
EGSM900
@power level #5 <300mA, Typical 175mA
@power level #12, Typical 83mA
@power level #19, Typical 63mA
DCS1800
@power level #0 <250mA, Typical 153mA
@power level #7, Typical 73mA
@power level #15, Typical 60mA
PCS1900
@power level #0 <250mA, Typical 151mA
@power level #7, Typical 76mA
@power level #15, Typical 61mA
GPRS Data
DATA Mode, GPRS (3 Rx, 2Tx) CLASS 12
GSM850
@power level #5 <550mA, Typical 363mA
@power level #12, Typical 131mA
@power level #19, Typical 91mA
EGSM900
@power level #5 <550mA, Typical 356mA
@power level #12, Typical 132mA
@power level #19, Typical 92mA
DCS1800
@power level #0 <450mA, Typical 234mA
@power level #7, Typical 112mA
@power level #15, Typical 88mA
PCS1900
@power level #0 <450mA, Typical 257mA
@power level #7, Typical 119mA
@power level #15, Typical 89mA
DATA Mode, GPRS (2 Rx, 3Tx) CLASS 12
GSM850
@power level #5 <640mA, Typical 496mA
@power level #12, Typical 159mA
@power level #19, Typical 99mA
EGSM900
@power level #5 <600mA, Typical 487mA
@power level #12, Typical 160mA
MC20_Hardware_Design
Confidential / Released
77 / 95
GSM/GPRS/GNSS Module Series
MC20 Hardware Design
@power level #19, Typical 101mA
DCS1800
@power level #0 <490mA, Typical 305mA
@power level #7, Typical 131mA
@power level #15, Typical 93mA
PCS1900
@power level #0 <480mA, Typical 348mA
@power level #7, Typical 138mA
@power level #15, Typical 94mA
DATA Mode, GPRS (4 Rx,1Tx) CLASS 12
GSM850
@power level #5 <350mA, Typical 216mA
@power level #12, Typical 103mA
@power level #19, Typical 83mA
EGSM900
@power level #5 <350mA, Typical 222mA
@power level #12, Typical 104mA
@power level #19, Typical 84mA
DCS1800
@power level #0 <300mA, Typical 171mA
@power level #7, Typical 96mA
@power level #15, Typical 82mA
PCS1900
@power level #0 <300mA, Typical 169mA
@power level #7, Typical 98mA
@power level #15, Typical 83mA
DATA Mode, GPRS (1 Rx, 4Tx) CLASS 12
GSM850
@power level #5 <600mA, Typical 470mA
@power level #12, Typical 182mA
@power level #19, Typical 106mA
EGSM900
@power level #5 <600mA, Typical 471mA
@power level #12, Typical 187mA
@power level #19, Typical 109mA
DCS1800
@power level #0 <500mA, Typical 377mA
@power level #7, Typical 149mA
@power level #15, Typical 97mA
PCS1900
@power level #0 <500mA, Typical 439mA
@power level #7, Typical 159mA
@power level #15, Typical 99mA
NOTE
GPRS Class 12 is the default setting. The GSM module can be configured from GPRS Class 1 to Class
12. Setting to lower GPRS class would make it easier to design the power supply for the GSM module.
MC20_Hardware_Design
Confidential / Released
78 / 95
GSM/GPRS/GNSS Module Series
MC20 Hardware Design
Table 38: Current Consumption of the GNSS Part
Parameter
Conditions
Typ.
Unit
IVCC @Acquisition
@VCC=3.3V (GPS)
25
mA
IVCC @Tracking
@VCC=3.3V (GPS)
19
mA
IVCC @Acquisition
@VCC=3.3V (GPS+BeiDou)
23
mA
IVCC @Tracking
@VCC=3.3V (GPS+BeiDou)
18
mA
IVCC @Standby
@VCC=3.3V
0.3
mA
IBCKP @backup
@V_BCKP=3.3V
14
uA
NOTE
The tracking current is tested in following conditions:
 For Cold Start, 10 minutes after First Fix.
 For Hot Start, 15 seconds after First Fix.
5.5. Electrostatic Discharge
Although the module is generally protected against Electrostatic Discharge (ESD), ESD protection
precautions should still be emphasized. Proper ESD handling and packaging procedures must be applied
throughout the processing, handling and operation of any applications using the module.
The measured ESD values of the module are shown in the following table.
Table 39: ESD Endurance (Temperature: 25ºC, Humidity: 45%)
Tested Point
Contact Discharge
Air Discharge
VBAT, GND
±5KV
±10KV
RF_ANT
±5KV
±10KV
TXD, RXD
±2KV
±4KV
GNSS_TXD
GNSS_RXD
±2KV
±4KV
Others
±0.5KV
±1KV
MC20_Hardware_Design
Confidential / Released
79 / 95
GSM/GPRS/GNSS Module Series
MC20 Hardware Design
MC20_Hardware_Design
Confidential / Released
80 / 95
GSM/GPRS/GNSS Module Series
MC20 Hardware Design
Mechanical Dimensions
This chapter describes the mechanical dimensions of the module.
6.1. Mechanical Dimensions of Module
Figure 42: MC20 Top and Side Dimensions (Unit: mm)
MC20_Hardware_Design
Confidential / Released
81 / 95
GSM/GPRS/GNSS Module Series
MC20 Hardware Design
Figure 43: MC20 Bottom Dimensions (Unit: mm)
MC20_Hardware_Design
Confidential / Released
82 / 95
GSM/GPRS/GNSS Module Series
MC20 Hardware Design
6.2. Recommended Footprint
Figure 44: Recommended Footprint (Unit: mm)
NOTES
1.
2.
For convenient maintenance, the module should be kept about 3mm away from the other
components in the host PCB.
The circular test points with a radius of 1.75mm in the above recommended footprint should be
treated as keepout areas. (“keepout” means do not pour copper on the mother board).
MC20_Hardware_Design
Confidential / Released
83 / 95
GSM/GPRS/GNSS Module Series
MC20 Hardware Design
6.3. Top and Bottom View of the Module
Figure 45: Top View of the Module
Figure 46: Bottom View of the Module
NOTE
These are design effect drawings of MC20 module. For more accurate pictures, please refer to the
module that you get from Quectel.
MC20_Hardware_Design
Confidential / Released
84 / 95
GSM/GPRS/GNSS Module Series
MC20 Hardware Design
Storage and Manufacturing
7.1. Storage
MC20 module is stored in a vacuum-sealed bag. The storage restrictions are shown as below.
1.
Shelf life in the vacuum-sealed bag: 12 months at <40ºC and <90%RH.
2.
After the vacuum-sealed bag is opened, devices that need to be mounted directly must be:


Mounted within 72 hours at the factory environment of ≤30ºC and <60% RH.
Stored at <10% RH.
3.
Devices require baking before mounting, if any circumstance below occurs.


When the ambient temperature is 23ºC±5ºC and the humidity indication card shows the humidity
is >10% before opening the vacuum-sealed bag.
Device mounting cannot be finished within 72 hours when the ambient temperature is <30ºC and the
humidity is <60%.
Stored at >10% RH.
4.
If baking is required, devices should be baked for 48 hours at 125ºC±5ºC.

NOTE
As the plastic package cannot be subjected to high temperature, it should be removed from devices
before high temperature (125ºC) baking. If shorter baking time is desired, please refer to
IPC/JEDECJ-STD-033 for baking procedure.
7.2. Soldering
Push the squeegee to apply the solder paste on the surface of stencil, thus making the paste fill the
stencil openings and then penetrate to the PCB. The force on the squeegee should be adjusted properly
so as to produce a clean stencil surface on a single pass. To ensure the module soldering quality, the
MC20_Hardware_Design
Confidential / Released
85 / 95
GSM/GPRS/GNSS Module Series
MC20 Hardware Design
thickness of stencil at the hole of the module pads should be 0.2 mm for MC20. For more details, please
refer to document [12]
It is suggested that the peak reflow temperature is from 235ºC to 245ºC (for SnAg3.0Cu0.5 alloy). The
absolute maximum reflow temperature is 260ºC. To avoid damage to the module caused by repeated
heating, it is suggested that the module should be mounted after reflow soldering for the other side of
PCB has been completed. Recommended reflow soldering thermal profile is shown below:
℃
Preheat
Heating
Cooling
250
Liquids
Temperature
217
200℃
200
40s~60s
160℃
150
70s~120s
100
Between 1~3℃/S
50
50
100
150
200
250
300
Time(s)
Figure 47: Reflow Soldering Thermal Profile
7.3. Packaging
The modules are stored in a vacuum-sealed bag which is ESD protected. It should not be opened until the
devices are ready to be soldered onto the application.
MC20_Hardware_Design
Confidential / Released
86 / 95
GSM/GPRS/GNSS Module Series
MC20 Hardware Design
7.3.1. Tape and Reel Packaging
Figure 48: Tape and Reel Specification
Figure 49: Dimensions of Reel
Table 40: Reel Packaging
Model Name
MC20
MC20_Hardware_Design
MOQ for
MP
Minimum
Package:250pcs
Minimum
Packagex4=1000pcs
250pcs
Size:
370mm×350mm×56mm
N.W: 0.32kg
G.W: 1.08kg
Size:
380mm×250mm×365mm
N.W: 1.28kg
G.W: 4.8kg
Confidential / Released
87 / 95
GSM/GPRS/GNSS Module Series
MC20 Hardware Design
Appendix A References
Table 41: Related Documents
SN
Document Name
Remark
[1]
Quectel_MC20_AT_Commands_Manual
MC20 AT commands manual
[2]
ITU-T Draft new recommendation V.25ter
Serial asynchronous automatic dialing
and control
[3]
GSM 07.07
Digital cellular telecommunications
(Phase 2+); AT command set for GSM
Mobile Equipment (ME)
[4]
GSM 07.10
Support GSM 07.10 multiplexing
protocol
GSM 07.05
Digital cellular telecommunications
(Phase 2+); Use of Data Terminal
Equipment – Data Circuit terminating
Equipment (DTE – DCE) interface for
Short Message Service (SMS) and
Cell Broadcast Service (CBS)
GSM 11.14
Digital cellular telecommunications
(Phase 2+); Specification of the SIM
Application Toolkit for the Subscriber
Identity module – Mobile Equipment
(SIM – ME) interface
GSM 11.11
Digital cellular telecommunications
(Phase 2+); Specification of the
Subscriber Identity module – Mobile
Equipment (SIM – ME) interface
GSM 03.38
Digital cellular telecommunications
(Phase 2+); Alphabets and
language-specific information
GSM 11.10
Digital cellular telecommunications
(Phase 2); Mobile Station (MS)
conformance specification; Part 1:
Conformance specification
[5]
[6]
[7]
[8]
[9]
MC20_Hardware_Design
Confidential / Released
88 / 95
GSM/GPRS/GNSS Module Series
MC20 Hardware Design
[10]
GSM_UART_Application_Note
UART port application note
[11]
GSM_EVB_User_Guide
GSM EVB user guide
[12]
Module_Secondary_SMT_User_Guide
Module secondary SMT user guide
[13]
Quectel_GSM_Module_Digital_IO_Application_Note
GSM Module Digital IO Application
Note
Table 42: Terms and Abbreviations
Abbreviation
Description
ADC
Analog-to-Digital Converter
AMR
Adaptive Multi-Rate
ARP
Antenna Reference Point
ASIC
Application Specific Integrated Circuit
BER
Bit Error Rate
BOM
Bill of Material
BT
Bluetooth
BTS
Base Transceiver Station
CHAP
Challenge Handshake Authentication Protocol
CS
Coding Scheme
CSD
Circuit Switched Data
CTS
Clear to Send
DAC
Digital-to-Analog Converter
DRX
Discontinuous Reception
DSP
Digital Signal Processor
DCE
Data Communications Equipment (typically module)
DTE
Data Terminal Equipment (typically computer, external controller)
DTR
Data Terminal Ready
MC20_Hardware_Design
Confidential / Released
89 / 95
GSM/GPRS/GNSS Module Series
MC20 Hardware Design
DTX
Discontinuous Transmission
EFR
Enhanced Full Rate
EGSM
Enhanced GSM
EMC
Electromagnetic Compatibility
ESD
Electrostatic Discharge
ETS
European Telecommunication Standard
FCC
Federal Communications Commission (U.S.)
FDMA
Frequency Division Multiple Access
FR
Full Rate
FS
File System
GMSK
Gaussian Minimum Shift Keying
GPRS
General Packet Radio Service
GSM
Global System for Mobile Communications
G.W
Gross Weight
HR
Half Rate
I/O
Input/Output
IC
Integrated Circuit
IMEI
International Mobile Equipment Identity
IOmax
Maximum Output Load Current
kbps
Kilo Bits Per Second
LED
Light Emitting Diode
Li-Ion
Lithium-Ion
MO
Mobile Originated
MOQ
Minimum Order Quantity
MP
Manufacture Product
MC20_Hardware_Design
Confidential / Released
90 / 95
GSM/GPRS/GNSS Module Series
MC20 Hardware Design
MS
Mobile Station (GSM engine)
MT
Mobile Terminated
N.W
Net Weight
PAP
Password Authentication Protocol
PBCCH
Packet Switched Broadcast Control Channel
PCB
Printed Circuit Board
PDU
Protocol Data Unit
PPP
Point-to-Point Protocol
RF
Radio Frequency
RMS
Root Mean Square (value)
RTC
Real Time Clock
RX
Receive Direction
SIM
Subscriber Identification Module
SMS
Short Message Service
TDMA
Time Division Multiple Access
TE
Terminal Equipment
TX
Transmitting Direction
UART
Universal Asynchronous Receiver & Transmitter
URC
Unsolicited Result Code
USSD
Unstructured Supplementary Service Data
VSWR
Voltage Standing Wave Ratio
VOmax
Maximum Output Voltage Value
VOnorm
Normal Output Voltage Value
VOmin
Minimum Output Voltage Value
VIHmax
Maximum Input High Level Voltage Value
MC20_Hardware_Design
Confidential / Released
91 / 95
GSM/GPRS/GNSS Module Series
MC20 Hardware Design
VIHmin
Minimum Input High Level Voltage Value
VILmax
Maximum Input Low Level Voltage Value
VILmin
Minimum Input Low Level Voltage Value
VImax
Absolute Maximum Input Voltage Value
VInorm
Absolute Normal Input Voltage Value
VImin
Absolute Minimum Input Voltage Value
VOHmax
Maximum Output High Level Voltage Value
VOHmin
Minimum Output High Level Voltage Value
VOLmax
Maximum Output Low Level Voltage Value
VOLmin
Minimum Output Low Level Voltage Value
Phonebook Abbreviations
LD
SIM Last Dialing phonebook (list of numbers most recently dialed)
MC
Mobile Equipment list of unanswered MT Calls (missed calls)
ON
SIM (or ME) Own Numbers (MSISDNs) list
RC
Mobile Equipment list of Received Calls
SM
SIM phonebook
MC20_Hardware_Design
Confidential / Released
92 / 95
GSM/GPRS/GNSS Module Series
MC20 Hardware Design
Appendix B GPRS Coding Schemes
Four coding schemes are used in GPRS protocol. The differences between them are shown in the
following table.
Table 43: Description of Different Coding Schemes
USF
Pre-coded
USF
Radio Block
excl.USF and
BCS
BCS
1/2
181
CS-2
2/3
CS-3
3/4
CS-4
Scheme
Code
Rate
CS-1
Tail
Coded
Bits
Punctured
Bits
Data
Rate
Kb/s
40
456
9.05
268
16
588
132
13.4
312
16
676
220
15.6
12
428
16
456
21.4
Radio block structure of CS-1, CS-2 and CS-3 is shown as the figure below.
Radio Block
BCS
USF
Rate 1/2 convolutional coding
Puncturing
456 bits
Figure 50: Radio Block Structure of CS-1, CS-2 and CS-3
MC20_Hardware_Design
Confidential / Released
93 / 95
GSM/GPRS/GNSS Module Series
MC20 Hardware Design
Radio block structure of CS-4 is shown as the following figure.
Radio Block
BCS
USF
Block
Code
No coding
456 bits
Figure 51: Radio Block Structure of CS-4
MC20_Hardware_Design
Confidential / Released
94 / 95
GSM/GPRS/GNSS Module Series
MC20 Hardware Design
10 Appendix C GPRS Multi-slot Classes
Twenty-nine classes of GPRS multi-slot modes are defined for MS in GPRS specification. Multi-slot
classes are product dependent, and determine the maximum achievable data rates in both the uplink and
downlink directions. Written as 3+1 or 2+2, the first number indicates the amount of downlink timeslots,
while the second number indicates the amount of uplink timeslots. The active slots determine the total
number of slots the GPRS device can use simultaneously for both uplink and downlink communications.
The description of different multi-slot classes is shown in the following table.
Table 44: GPRS Multi-slot Classes
Multislot Class
Downlink Slots
Uplink Slots
Active Slots
10
11
12
MC20_Hardware_Design
Confidential / Released
95 / 95

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Author                          : lenovo
Create Date                     : 2016:10:10 10:14:21+08:00
Modify Date                     : 2016:10:10 10:14:21+08:00
XMP Toolkit                     : Adobe XMP Core 4.2.1-c041 52.342996, 2008/05/07-20:48:00
Format                          : application/pdf
Title                           : Microsoft Word - Quectel_MC20_Hardware_Design_V1.0_FCC
Creator                         : lenovo
Creator Tool                    : PScript5.dll Version 5.2.2
Producer                        : Acrobat Distiller 9.0.0 (Windows)
Document ID                     : uuid:29185cc3-e0b4-4ab4-b45e-02d4c7d52523
Instance ID                     : uuid:9833f6ef-d6e8-4f1d-af50-86766ae333c9
Page Count                      : 96

EXIF Metadata provided by EXIF.tools

Quectel Wireless Solutions 201609MC20 GSM/GPRS/GNSS Module User Manual

Quectel Wireless Solutions Company Limited GSM/GPRS/GNSS Module

User Manual

FCC ID Filing: XMR201609MC20

Navigation menu

Namespaces

Views

Navigation