R H Peterson l VR-1 Remote Control Transmitter User Manual a2 169 pmd

Download:
Mirror Download [FCC.gov]
Document ID	414993
Application ID	Q2PfiGNhZk34MoMLIWD2hg==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	6.99kB (87331 bits)
Date Submitted	2004-04-16 00:00:00
Date Available	2004-04-15 00:00:00
Creation Date	2004-03-29 08:09:39
Producing Software	Acrobat Distiller 5.0.5 (Windows)
Document Lastmod	2004-03-29 08:09:39
Document Title	a2-169.pmd
Document Creator	PageMaker 7.0
Document Author:	cpeace

ROBERT H. PETERSON CO.
MODEL# VR-1
BASIC VARIABLE REMOTE SYSTEM
RECEIVER & TRANSMITTER KIT.
VR-1 SET COMPRISES OF THE FOLLOWING PARTS:
Item No.
1.
2.
3.
4.
Part No.
Description
10282
10310
Transmitter
Receiver
Valve Connection wiring
4x AA Batteries
INSTALLATION AND OPERATING INSTRUCTIONS
NOTICE TO INSTALLER:
Please leave these instructions with the consumer
NOTICE TO CONSUMER:
Please retain for future reference
RECEIVER INSTALLATION STEPS
ATTACH FEMALE
CONNECTORS
TO
CORRECT MALE
SPADES ON
VALVE
Step 1. Attach the supplied wires with female connectors to their
proper mating terminals on the valve (See Figure 1).
Step 2. Attach the open wire ends to the terminal block on the
receiver by connecting the marked wire to the positive (+)
terminal and the unmarked wire to the negative (-) terminal.
Tighten down the retaining screws (See Figure 2).
Figure 1
Step 3. To install batteries into the receiver, squeeze together the
tabs on the battery compartment and lift out (See Figure 3).
Insert the four (4) AA batteries (supplied with your kit) into the
compartment, ensuring they are correctly aligned by referring to the
markings in the compartment. Replace compartment.
NOTE: It is recommended that you replace the batteries annually
with fresh batteries. Always replace the four batteries at same time.
INSERT WIRING INTO RECEIVER &
TIGHTEN DOWN SCREWS AT BACK
Step 4. IMPORTANT: ACTIVATE YOUR RECEIVER BY PRESSING
THE RESET (LOCATED ABOVE THE SWITCH, SEE FIGURE 3)
WITH A FINE OBJECT SUCH AS A PAPERCLIP.
Place the receiver not closer than 18" to the log set.
An optional receiver cover (PCDC-1 or WCDC-1) is available
from your Peterson dealer.
Figure 2
Step 5. To activate the handset, remove the white tag from rear of
handset.
OFF
REMOVE
THIS TAG
(PULL OUT)
REMOTE
PRESS
RESET
TO
ACTIVATE
RECEIVER
OFF
TO OPERATE REMOTE SEE PAGE 2
PRESS
TABS IN
TOWARDS
CENTER
& LIFT OUT
Figure 3
Rev 1 031004
No. L-A2-16904
VR-1 TRANSMITTER/RECEIVER OPERATION
Increasing flame height using the VR-1
Transmitter and Receiver:
TO INCREASE FLAME
PRESS “UP”
A. Set the receiver switch to the center (REMOTE)
position.
B. With the gas supply turned on and the gas log set lit,
point the handset towards the receiver and press the
"UP" Button (the red indicator light on both handset and
receiver should show). Flame height will increase until the
maximum is reached.
Decreasing flame height using the VR-1 Transmitter
and Receiver:
C. Set the receiver switch to the center (REMOTE)
position.
D. While the main burner is lit, point the handset
towards the receiver and press the "DOWN"
Button (the red indicator light on both handset and
receiver should show). Flame height will decrease.
USING THE RECEIVER TO
CONTROL LOG SET
OFF
REMOTE
OFF
To turn off the Remote option
and control the log set
manually, set the receiver
switch to "OFF"
( top or bottom position)
To set the switch for Remote
use, set the receiver switch to
"REMOTE"(center position)
TOP
PRESS “DOWN”
TO DECREASE FLAME
FCC ID: RWPVR-1
This device complies with part 15 of the FCC rules. Operation of this device is subject to the following conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user's
authority to operate the equipment.
ROBERT H. PETERSON COMPANY
VALVES and SAFETY PILOT ASSEMBLIES
LIMITED WARRANTY
All Peterson Valves and Safety Pilot Assemblies are covered by a one (1) year limited warranty.
Defective or broken parts for replacement must be returned to your dealer or to the factory, freight prepaid. Item will be repaired or replaced
at factory option, and returned to purchaser, freight collect.
This warranty does not cover parts becoming defective by misuse, accidental damage, improper handling and/or installation nor does
it cover labor or labor related charges. Valves and pilot assemblies must be installed in accordance with local code and as outlined in
the enclosed instructions.
This warranty specifically excludes liability for indirect, incidental or consequential damage to property. Some states do not allow the
exclusion or limitation of incidental or consequential damages, so the above exclusion or limitation may not apply to you. This warranty
gives you specified legal rights and you may also have other rights which vary from state to state.
Robert H. Peterson Co. 14724 East Proctor Avenue, City of Industry, California 91746

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Create Date                     : 2004:03:29 08:09:39-08:00
Modify Date                     : 2004:03:29 08:09:39-08:00
Page Count                      : 2
Creation Date                   : 2004:03:29 16:09:39Z
Mod Date                        : 2004:03:29 16:09:39Z
Producer                        : Acrobat Distiller 5.0.5 (Windows)
Author                          : cpeace
Metadata Date                   : 2004:03:29 16:09:39Z
Creator                         : cpeace
Title                           : a2-169.pmd

EXIF Metadata provided by EXIF.tools