R tron APEX1933 Industrial Booster User Manual Rev 6
R-tron Inc. Industrial Booster Users Manual Rev 6
R tron >
Users Manual Rev 6
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 2213799 |
| Application ID | VGSFOkMil4V6cxYEFoXbDg== |
| Document Description | Users Manual Rev 6 |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 326.65kB (4083106 bits) |
| Date Submitted | 2014-03-12 00:00:00 |
| Date Available | 2014-04-26 00:00:00 |
| Creation Date | 2014-03-12 16:43:37 |
| Producing Software | Acrobat Distiller 7.0.5 (Windows) |
| Document Lastmod | 2014-03-12 18:02:22 |
| Document Title | Microsoft Word - APEX1933 User's Manual_20140120_V.1.2.docx |
| Document Creator | PScript5.dll Version 5.2.2 |
| Document Author: | User |
APEX1933 User’s Manual Please read this manual before operating this product. After you finish reading this manual, store it in a safe place for future reference. FCC NOTIFICATION This equipment generates or uses radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made. This is NOT a CONSUMER device. It is designed for installation by FCC LICENSEES and QUALIFIED INSTALLERS. You MUST have an FCC LICENSE or express consent of an FCC Licensee to operate this device. Unauthorized use may result in significant forfeiture penalties, including penalties in excess of $100,000 for each continuing violation. Regulatory Statements This device complies with Part 15 of the FCC Rules. Operation is subject to the following two Conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy, and if it is not installed and used in accordance with the instruction manual, it may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his own expense. Modifications: Any modifications made to this device that are not approved by Sun Microsystems, Inc. may void the authority granted to the user by the FCC to operate this equipment. WARNING: Only authorized antennas and cables described in this manual are permitted to be used with this device. Other antennas and cables are expressly forbidden to be used. Authorized Antennas: YG-1900-12: Yagi Antenna ACPS-1900-8: Indoor Directional Patch Antenna TABLE OF CONTENTS 1. GENERAL........................................................................................................................................................... 1 1.1 NOTICE .............................................................................................................................................................................................1 1.2 SAFETY PRECAUTIONS ...................................................................................................................................................................2 1.3 VERSION HISTORY ..........................................................................................................................................................................3 1.3.1 Manual Version History List .................................................................................................................................................3 1.3.2 Firmware Version History List .............................................................................................................................................3 1.3.3 WEB GUI Version History List .............................................................................................................................................3 1.4 GLOSSARY .......................................................................................................................................................................................4 2. INTRODUCTION ............................................................................................................................................... 5 2.1 APEX1933 ......................................................................................................................................................................................5 2.2 APEX1933 KEY FEATURES..........................................................................................................................................................6 2.3 COMPONENTS ..................................................................................................................................................................................6 2.3.1 APEX1933 ................................................................................................................................................................................6 2.4 DESCRIPTION ...................................................................................................................................................................................7 2.4.1 Overview ...................................................................................................................................................................................7 2.4.2 INTERNAL CONFIGURATION ........................................................................................................................................................8 2.4.3 RFU (Radio Frequency Unit) ...............................................................................................................................................9 2.4.4 Duplexer ...................................................................................................................................................................................9 2.4.5 PSU (Power Supply Unit)......................................................................................................................................................9 2.4.6 NCU (Network Control Unit) ...............................................................................................................................................9 3. MECHANICAL INSTALLATION.................................................................................................................... 12 3.1 MOUNTING.................................................................................................................................................................................... 12 4. CABLE INSTALLATION ................................................................................................................................ 14 4.1 CABLE CONNECTION ................................................................................................................................................................... 14 4.2 POWER ON .................................................................................................................................................................................... 15 4.3 GROUNDING ................................................................................................................................................................................. 15 5. GUI OPERATION............................................................................................................................................. 16 5.1 GUI OPERATION FLOW CHART ................................................................................................................................................. 16 5.2 INTERNET NETWORK SETUP ...................................................................................................................................................... 17 5.2.1 Windows 7 (Refer to 5.9 for other versions of Windows) ............................................................................................. 17 5.3 SYSTEM LOGIN............................................................................................................................................................................. 18 5.4 SYSTEM SETUP ............................................................................................................................................................................. 19 5.4.1 Time Setting ........................................................................................................................................................................... 19 5.4.2 Network Setup ....................................................................................................................................................................... 19 5.4.3 User Note ............................................................................................................................................................................... 21 5.4.4 User Comment ...................................................................................................................................................................... 22 5.5 GUI SYSTEM CONTROL .............................................................................................................................................................. 23 5.5.1 SYSTEM CONTROL .................................................................................................................................................................... 23 5.5.2 Operating Control................................................................................................................................................................ 24 5.5.3 Alarm Control ....................................................................................................................................................................... 26 5.5.4 Band Select ............................................................................................................................................................................ 26 5.6 GUI SYSTEM SETUP .................................................................................................................................................................... 27 5.6.1 Easy Setup ............................................................................................................................................................................. 27 5.6.2 MANUAL GAIN SETTING .......................................................................................................................................................... 30 5.7 GUI STATUS .................................................................................................................................................................................. 33 5.7.1 System ..................................................................................................................................................................................... 33 5.7.2 Operating............................................................................................................................................................................... 33 5.7.3 Alarm ...................................................................................................................................................................................... 33 5.8 FILE UPDATE ................................................................................................................................................................................ 34 5.8.1 MCU Firmware Download ................................................................................................................................................ 34 5.8.2 Web GUI Download............................................................................................................................................................. 36 5.9 ATTACHMENT ............................................................................................................................................................................... 37 5.9.1 Internet Network Setting ...................................................................................................................................................... 37 6. TROUBLESHOOTING .................................................................................................................................... 40 6.1 LED ALARM................................................................................................................................................................................. 40 6.2 GUI ALARM.................................................................................................................................................................................. 41 6.3 COMMUNICATION ALARM .......................................................................................................................................................... 42 7. SPECIFICATIONS............................................................................................................................................ 44 7.1 RF CHARACTERISTICS ................................................................................................................................................................ 44 7.2 ENVIRONMENTAL SPECIFICATION ............................................................................................................................................. 45 7.3 ELECTRICAL SPECIFICATION ...................................................................................................................................................... 45 7.4 MECHANICAL SPECIFICATION .................................................................................................................................................... 45 8. APPENDIX ........................................................................................................................................................ 46 8.1 US PCS CHANNEL....................................................................................................................................................................... 46 8.2 WARRANTY ................................................................................................................................................................................... 47 8.3 RETURN MATERIAL AUTHORIZATION (RMA) PROCEDURE.................................................................................................. 47 1. General 1.1 Notice Trademark R-tron is a registered trademark of R-tron Inc. Other products and company names mentioned here in this manual might be trademarks or trade names of their respective owners. Copyright Copyright © R-tron Inc. 2000-2014 All Rights Reserved Any reproduction, distribution, or revisions of any or all portions of this manual is prohibited without written permission from R-tron Inc. Notice This document describes the specifications, installation, and operation of the APEX1933 equipment. Hardware and software mentioned in this document are subject to continuous development and improvement. Consequently, there may be minor discrepancies between the information in the document, performance, and design of the product. Specifications, dimensions, and other statements mentioned in this document are subject to change without notice. Questions or Comments Address: R-tron Inc. 6402 College Boulevard, Overland Park, KS 66211 Phone: +1-913-344-9977, 1-888-317-8766 Fax: +1-913-344-9988 e-mail: info@r-tronamerica.com Website: www.rtronamerica.com APEX1933 USER MANUAL V1.2 Tech Support: 1-888-317-8766 1.2 Safety Precautions Opening the APEX1933 equipment could result in electric shock and may cause severe injury. Connect the equipment frame ground to the building ground. Operating the APEX1933 with antennas in very close proximity facing each other can lead to severe damage to the equipment. RF Exposure Infomation The antenna(s) must be installed in a fixed installation and provide a separation distance of 76 cm from all persons and must not be collocated with any other transmitters except in accordance with FCC multi-transmitter product procedures for both YG-1900-12 antenna and ACPS-1900-8 antenna. For more information about RF exposure, please visit the FCC website at www.fcc.gov This equipment is for indoor use only and enables the communication wiring to communicate inside the building. Antenna Requirements ANTENNAS: please read your manufacturers antenna specifications before installation. Your antenna will require a type "N" connection. The antenna, Coax., and fittings must be 50 ohms. APEX1933 USER MANUAL V1.2 Tech Support: 1-888-317-8766 1.3 Version History 1.3.1 Manual Version History List Revision History Approval Ver. Issue Ver. V1.0 Date Item/Description 2013. 10. 18 Initial Version V1.0 V1.1 2013. 10. 31 Component List Modification V1.1 V1.2 2014. 01. 20 Key features Modification Reason 1.3.2 Firmware Version History List Revision History Approval Ver. Issue Ver. V1.0.00 V1.0.00 Date Item/Description 2013. 10. 18 Initial Version Reason 1.3.3 WEB GUI Version History List Revision History Approval Ver. Issue Ver. V1.3.00 V1.3.00 Date Item/Description 2013. 10. 18 APEX Series Common GUI APEX1933 USER MANUAL V1.2 Reason Tech Support: 1-888-317-8766 1.4 Glossary The following is a list of abbreviations and terms used in this manual. Abbreviation Definition AC Alternating Current CDMA Code Division Multiple Access DC Direct Current DL Downlink GUI Graphic User Interface LED Light Emitting Diode PSU Power Supply Unit RF Radio Frequency UL Uplink VSWR Voltage Standing Wave Ratio NCU Network Control Unit MCU Main Control Unit NMS Network Management System SNMP Simple Network Management Protocol AGC (Automatic Gain Control) AGC prevents the equipment from exceeding its maximum output power by reducing the gain automatically. AGC is used to adjust the gain to an appropriate level for a range of input signal levels. ASD (Automatic Shutdown) ASD helps protect the amplifier from over load. ASD helps protect the network by preventing excessive signal output power. ASD does not: 1. Prevent oscillation 2. Protect from excessive input. There are three parameters: ASD Level, ASD Time, and ASD Iteration. If the output power exceeds higher than the “ASD LEVEL”, the equipment will shut down for “ASD TIME” seconds. If shutdown repeats “Iteration” times, the equipment will require manual re-start. APEX1933 USER MANUAL V1.2 Tech Support: 1-888-317-8766 2. Introduction 2.1 APEX1933 APEX1933 is used to fill out areas in APEX systems, such as base station fringe areas, business and industrial building, etc. APEX1933 receives signals from a Small Cell (Femto-Cell, Optional), amplifies and retransmits the signals to the mobile stations. It also receives, amplifies and retransmits signals in the opposite direction. Both directions are served simultaneously with the following features: < Basic Organization > Note : Femto-cells will be one of the following products: FCC ID:R4HAWEPPRO or FCC ID:QHYHUBBUBC4500-RT or FCC ID:QHYHUBBUBC4501-RT. Femto-cells that are used with APEX 1933 must be connected to a wired uplink configuration. Both up link and down link of the femtocell will be wired connections only when used with APEX 1933. APEX1933 USER MANUAL V1.2 Tech Support: 1-888-317-8766 2.2 APEX1933 Key Features ◈ Design - Digital filtering allows for customized channel selections. - Digital filtering high quality, out of band rejection, and high performance ◈ User friendly design. - Local monitoring and control through the Web GUI interface - Remote monitoring and control through the Web GUI interface. - Reports the status of connection as a function of SNMP regularly and reports an alarm if the event occurred. ◈ Protection function - Easy setup - Isolation Check - Auto Gain Control - Auto Shutdown 2.3 Components 2.3.1 APEX1933 APEX1924/1930/1933 Package Index Items Q’ty Equipment equipment) Wall Mount Bracket LAN Cable AC Cable Bolt (M4*8mm) Bolt (M6*16mm) APEX1933 USER MANUAL V1.2 NCU (Installed in Direct LAN Cable(120mm) Direct LAN Cable(1M) Remark For standalone APEX PCS Series operation Cross Type LAN Cable Strait through LAN cable for standalone APEX PCS Series operation 10 Quick Guide 11 User’s Manual CD Optional Tech Support: 1-888-317-8766 No.2, 4 and 8 are for standalone APEX1924/1930/1933 operation. 2.4 Description 2.4.1 Overview APEX1933 USER MANUAL V1.2 Tech Support: 1-888-317-8766 2.4.2 Internal Configuration APEX1933 USER MANUAL V1.2 Tech Support: 1-888-317-8766 2.4.3 RFU (Radio Frequency Unit) The RFU (RF Unit) is a bi-directional amplifier that sharply filters out unwanted noise. 2.4.4 Duplexer A duplexer is a device that combines two or more signals onto a common channel or medium to increase its transmission efficiency. 2.4.5 PSU (Power Supply Unit) The AC-DC adaptor supplies a steady DC power to the APEX19xx equipment by drawing power from the general in-wall AC outlets. 2.4.6 NCU (Network Control Unit) The NCU (Network Control Unit) is the control unit of the APEX19xx. The NCU controls and monitors operational parameters, alarms, records event and performs many other functions. 2.4.7 ANTENNA REQUIREMENTS ANTENNAS: please read your manufacturers antenna specifications before installation. Your antenna will require a type “N” connection. The antenna, coax, and fittings must be 50 ohms impedance. MAXIMUM ANTENNA SIZE CONNECTED TO THE APEX1933 REPEATER IS 12dBi, The CDMA repeater requires antennas that operate in the desired frequency range of the CDMA repeater. The APEX1933 Repeater has a frequency operating range of 1850 to 1915 MHz for the up- link, and 1930 to 1995 MHz for the downlink. Your antennas must operate within these frequencies. Failure to select the proper antennas will degrade the performance of your repeater. 2.4.8 ANTENNA ISOLATION & COAX CABLES To protect wireless CDMA networks from interference caused by oscillation, the APEX1933 Repeater has internal automatic oscillation detection/control and auto shut down of the repeater. Improper installation practices could can initiate automatic shut-down of your repeater. All repeaters require antenna isolation to prevent oscillation. The usable gain level of your repeater is directly linked to the antenna isolation values. The maximum gain of your repeater must be adjusted to a minimum of 10 dB lower than your antenna isolation values. For example, if your antenna isolation value is 43 dB then your maximum usable repeater gain is 33 dB. APEX1933 USER MANUAL V1.2 Tech Support: 1-888-317-8766 Due to the variations of system layouts and requirements it is not possible to have one procedure that will suffice every installation. You are strongly advised to acquire the services of an RF system designer to calculate your antenna isolation requirements. Ensure that your antennas are at the maximum possible distance apart. Do not place antennas in close proximity to each other; otherwise you will activate the oscillation detection process. Coax cables should be low loss 50 ohm, and suitable for 1850 to 1915 / 1930 to 1995 MHz band frequency. Antenna connections should be clean and moisture free. Do not spray lubricant into the connectors as this prevents the signal traveling through the coax. Use a cleaning solvent that has no oil and does not leave any residue. High quality oil-less contact cleaner is suitable. All coax connectors must be water tight and wrapped with water proof tape. Any moisture in the connectors will degrade or eliminate the signals. 2.4.9 ANTENNA CONNECTIONS ON THE APEX1933 The APEX1933 can be installed indoors. If mounted indoors ensure there is no elevated room temperatures and free flowing air for cooling of the repeater. Connect the antenna that is aimed at the Cell Tower to the bottom left side N connector. Connect the antenna that is aimed towards the Area Fill (target site) to the bottom right side N connector. Connect your Ethernet cable to the connector socket located on the left side of the power on LED light. NOTE; Water proof boot cover for the Ethernet connection, contact your Repeater supplier. 2.4.10 ADJUSTING REVERSE LINK MAXIMUM POWER LEVEL. Additional protection is gained if the reverse link maximum power level is adjusted to prevent the possibility of sudden unwanted high input RF levels. This can happen in various ways, mobile cellular vehicle boosters coming within range of the cellular repeaters, malfunctioning cellular phones, or other stray signals. The APEX1933 has an adjustable Maximum allowable RF Power limit. The maximum allowable RF power limit is 33dBm. The digitally controlled attenuator will not permit RF signal levels greater than 33dBm. The user can decrease the maximum allowable RF transmit power from 33 dBm to 0.0dBm. The microprocessor controlled digital attenuator will maintain the preset allowable RF transmit power limit regardless of unwanted high input signal levels. APEX1933 USER MANUAL V1.2 Tech Support: 1-888-317-8766 10 2.4.11 Calculating the Maximum Output Power allowed The regulatory limits for maximum output power are specified in EIRP (equivalent isotro pic radiated power). The EIRP level of a device will be installation dependent and final c onfiguration is the responsiblity of the professional installer. However in general the fin al EIRP can be calculated by adding the gain of the antenna used (specified in dBi) to the output power available at the connector (specified in dBm) minus any cable loss. APEX1933 USER MANUAL V1.2 Tech Support: 1-888-317-8766 11 3. Mechanical Installation The installation procedure is as follows: • Confirm Items from List • Mounting • Grounding • RF Cable Connection • Power On 3.1 Mounting Step 1 Drill holes directly through the template. Attach the mounting bracket to the wall using provided bolts (16/5*50mm) or extra screws. Step 2 Lean the APEX19xx to hang the topside of the Guide Ring on the mounting bracket, and push toward the wall to mount. APEX1933 USER MANUAL V1.2 Tech Support: 1-888-317-8766 12 Step 3 Fix the equipment using the 4 bolts (M6*12mm) provided. Step 4 Fix the equipment using the 2 bolts (M4*8mm) provided. Step 5 Connecting multiple APEX equipments. APEX1933 USER MANUAL V1.2 Tech Support: 1-888-317-8766 13 4. Cable Installation 4.1 Cable Connection Step 1: Connect a cable from the donor antenna to the Donor Antenna Port. Step 2: Connect a cable from a equipment’s service antenna to the Sever Antenna Port. APEX1933 USER MANUAL V1.2 Tech Support: 1-888-317-8766 14 4.2 Power On ※ Notice: Antenna cables must be installed before connecting AC Power. Step 1: Connect the power cord to the Equipment Step 2: Plug the power cord into a wall outlet. Step 3: Turn the red power button on Step 4: Check if the green LED at the Top turns on. 4.3 Grounding Step 1: A rod on the left side is intended for a building ground. Step 2: Connect the ground cable to the rod. APEX1933 USER MANUAL V1.2 Tech Support: 1-888-317-8766 15 5. GUI Operation APEX19xx operates on a customer provided PC based platform with the following system requirements: • Windows® XP or Windows® Vista, Windows 7 • Internet Explorer 6.0(Recommended) or higher. • 128 MB RAM or higher. • Pentium Ⅲ processor or higher. • RJ-45 Cable required. 5.1 GUI Operation Flow Chart APEX1933 USER MANUAL V1.2 Tech Support: 1-888-317-8766 16 5.2 Internet Network Setup 5.2.1 Windows 7 (Refer to 5.9 for other versions of Windows) Step 1: Click the Start button and select Control Panel. Step 2: Click Network and Internet. Step 3: Click Network and Sharing Center. Step 4: Click View status of Local Area Connection. Step 5: Click Properties and a caution pop-up Step 6: Select Internet Protocol Version 4 (TCP/IPv4) window will appear. Click OK. and click Properties. APEX1933 USER MANUAL V1.2 Tech Support: 1-888-317-8766 17 Step 7: Check Obtain an IP address automatically and click OK. Step 8: Close all windows. 5.3 System Login For APEX19xx operation access, go to Web GUI and Log in. Step 1: Open your Web browser and type http://192.168.0.1 into the URL address box. Then press the Enter key. Step 2: Confirm a User ID and type the password into the password box. Type “operator” for the password and then click OK. Step 3: The pop-up message for the login success will appear. Click OK. Step 4: When the login process is complete, the initial screen will appear. APEX1933 USER MANUAL V1.2 Tech Support: 1-888-317-8766 18 5.4 System Setup When you click Network in the initial screen you can set up User Note, Comment, Ethernet, and time setting. 5.4.1 Time Setting The time will automatically set to your PC time when you click OK. In the above page, you can set system date and time and update time-related information. 5.4.2 Network SetupAPEX1933 USER MANUAL V1.2 Tech Support: 1-888-317-8766 19 5.4.2.1 SYSTEM • Cascade Code: Type the pre-assigned cascade code. Otherwise, you cannot access the system setup. ¾ Set up for multiple bands Equipment with NCU installed is designated as the master control. The other equipments will connect to the master via RJ 45 cable. The master web GUI will display the other equipments if the connection is successful. 1) Cascade code 1 of SYSTEM in Network setup: Put Direct LAN Cable into Equipment 1 port and connect to NMS port. 2) For adding equipments refer to the RJ 45 cable connection below. Input Cascade codes to the cascade code table under the SYSTEM section. • Cascade Code Setting Chart Equipment Equipment 1 Equipment 2 Equipment 3 Equipment 4 Cascade code Cascade Code 1 Cascade Code 2 Cascade Code 3 Cascade Code 4 APEX1933 USER MANUAL V1.2 Tech Support: 1-888-317-8766 20 • Location Information: Enter the latitude and longitude. You can input values either in Decimal Degrees or Degrees-Minutes-Seconds. [Example] (‘N/S’ | ‘E/W’) ddd.dddddd: (Latitude: N 39.006967 Longitude: W 94.532306) • Refresh Time: Set each refresh time for connecting to Local port and Remote port. 5.4.2.2 ETHERNET SETTING • Ethernet IP Mode/IP Address: Enables you to set a connection mode for the network connected to the APEX19xx remote LAN port. When you “select” Auto, the device automatically assigns the IP address. When you select “Static”, it is possible to set an IP address of your choosing. • SNMP: In order to send Heartbeat and alarm related information to a remote monitoring server, you can set a server IP address. The factory default IP address is 10.22.25.15. • Heartbeat Interval: Sets the time to transmit the Heartbeat to the NMC Server. (Default value is 20 minutes.) 5.4.3 User Note APEX1933 USER MANUAL V1.2 Tech Support: 1-888-317-8766 21 • Location Information: Type the location information such as the building name, address, city, state, zip code and telephone, and then click Apply. • Donor Site Information: Type the base station’s ID, and then click Apply. • Installer Information: Type the installer information such as the company, name and telephone, Click Apply. 5.4.4 User Comment • User Comment: The user can store up to 50 comments in memory. The length of each comment is limited to 20 characters. APEX1933 USER MANUAL V1.2 Tech Support: 1-888-317-8766 22 5.5 GUI System Control 5.5.1 System Control APEX1933 USER MANUAL V1.2 Tech Support: 1-888-317-8766 23 • Easy Setup is a fast start function. The function measures Isolation, detects input level and assign gain to achieve maximum output power. The function ends with the equipment set to amplify signals in both directions within the confines of the band selection. Before running easy setup, set the center frequency and bandwidth (refer to 4.3.3 part 2). Maximum DL output power requires at least -10dBm input power and sufficient antenna isolation. • Isolation Check can be executed at anytime to measure isolation between the donor and server antennas. Isolation Check momentarily disables service. Isolation check automatically runs when factory default is initiated. • Factory Default restores the amplifier to its initial state. The function ends with amplifiers off, AGC mode off, gain set to minimum(15dB) and UL gain offset set to 0dB. Band selection and all other system parameters are not changed. The featurs is usefull in claering abnormal conditions. • System Reset cycles the microprocessor unit. The function is similar to switching off/on the equipment power switch. 5.5.2 Operating Control • DL and UL Path Control allows the user to toggle on or off the power amplifiers. • DL and UL Gain is available when AGC mode is off. The user may enter gain values manually. Manual gain control is an alternative to automatic gain control (AGC). Manual gain is disabled (grayed out) when AGC mode is on. Gain cannot be controlled manually above the available gain found on the status page. The system will not allow gain to be increased such that maximum output power (33dBm) is exceeded. APEX1933 USER MANUAL V1.2 Tech Support: 1-888-317-8766 24 • Gain Tracking sets UL gain equal to DL gain. The feature helps maintain forward and reverse link balance. The function control is grayed out when AGC mode is on. • Automatic Gain Control : - In contrast to manual gain control, automatic gain control (AGC) sets gain such that the desired amplifier output level (33dBm) is automatically set. - The user controls gain by adjusting the AGC level. The user may set the level from 0dBm to 33dBm. AGC can be used to control the signal level radiated from the server antennas. - AGC may also be user to match the equipment to a DAS (distributed antenna system). AGC level may be restricted by available gain and DL input power. • UL Gain offset is used in conjunction with AGC to reduce the amount of amplification in the reverse direction (uplink). In the cases UL offset is set to 0dB. • Automatic Shutdown (ASD) : - ASD temporarily shuts down the amplifier if the ASD level is exceeded. It is not necessary to turn off ASD. ASD events are stored in the alarm history log. Repeated ASD events will eventually shutdown the amplifier permanently and trigger the external shutdown lamp. - ASD Level is set to 36dBm by default. It is not necessary to change the default level. How to prevent saturation or over-modulation 1. Hardware function Input : If this device detect an over input signal, input hardware ALC will automatically activated over power rating+2dB within 100ns to protect it and in case of over ALC range turn to Thru-Path by activating a relay to prevent from occurring saturation of AMP and Digital board. Output : If this device detect an over output signal, output hardware ALC will automatically activated over power rating+2dB within 100ns to prevent from occurring over output power. 2. Software function to adjust the maximum power output and secure linear operation AGC(Automatic Gain Control) : automatically control the output power not to exceed over the set value. ALC : activating in AGC off condition to prevent from occurring over-output power APEX1933 USER MANUAL V1.2 Tech Support: 1-888-317-8766 25 5.5.3 Alarm Control • Alarm response time may be set between 0 and 5 minutes. • Alarm Mask allows the user to customize the type of alarms sent to the SNMP server when remote monitoring is in use. 5.5.4 Band Select • Band select sets the digital filter to the center frequency and bandwidth of the local service for which the equipment is intended to amplify. Likewise, all other signals outside of the selected Center Frequency and Bandwidth are rejected. • The user can select one, two three distinct sections within the PCS band. Each of the 1st, 2nd and 3rd filter blocks can be set to 1MHz to 20MHz of Bandwidth. Only the downlink center frequency is set by the user. The uplink center frequency is automatically set in accordance with the downlink frequencies. • Filter Rejection allows the user to change the digital filter characteristics. Normal rejection is used for CDMA and EVDO service. • Frequency information is available as a reference for setting the center frequency and band width (refer to section 7). APEX1933 USER MANUAL V1.2 Tech Support: 1-888-317-8766 26 5.6 GUI System Setup 5.6.1 Easy Setup Step 1: Click Apply after setting Center Frequency and Band Width in use. Step 2: Input AGC Level desired and click Apply. 1) AGC Level 33dBm 2) AGC Level 30dBm Step 3: Easy Setup proceeds to: • Data Initial execution • Isolation Test exeduted • Calculation of Available Maximum Gain by the isolation • DL/UL Path On • AGC On to obtain DL Output Power AGC Level or Maximum Gain 43dB • ASD On APEX1933 USER MANUAL V1.2 Tech Support: 1-888-317-8766 27 • AGC Off • Easy setup takes about 2minutes. Click Execute button of Easy Setup Step 4: Click OK. 1) AGC Level 33dBm 2) AGC Level 30dBm Step 5: Setup will automatically begin. This process takes approximately 3minutes. APEX1933 USER MANUAL V1.2 Tech Support: 1-888-317-8766 28 Result 1: Constant Maximum DL Output Power 33dBm (AGC Level 33dBm) If the DL input Power ≥ -10dBm Result 2: Constant Maximum DL Output Power 30dBm (AGC Level 30dBm) If the DL input Power ≥ -10dBm APEX1933 USER MANUAL V1.2 Tech Support: 1-888-317-8766 29 5.6.2 Manual Gain Setting 5.6.2.1 AGC mode “On” Setting Step 1: Repeat Step 1 through Step 2 Step 2: Isolation Check The Isolation will calculate the Available Maximum Gain which defines the maximum gain to be setup. Click Isolation Step 3: Click OK. Step 4: When below pop-up appears after Isolation is completed, click OK. APEX1933 USER MANUAL V1.2 Tech Support: 1-888-317-8766 30 Step 5: AGC must be turned on. AGC automatically assigns gain in accordance with AGC level. Use AGC level to increase or decrease gain. (Gain Offset is a gain differential between DL Output gain and UL output gain.) Ex> AGC Level 33dBm, Gain Offset -3dB → DL Gain 43dB, UL Gain 40dB AGC Level 33dBm, Gain Offset 0dB → DL Gain 43dB, UL Gain 43dB Step 6: Turn on the DL and UL path controls. APEX1933 USER MANUAL V1.2 Tech Support: 1-888-317-8766 31 5.6.2.2 AGC mode “Off” setting When you want to set gain value not using Auto Gain control refer to the following. Step 1: For manual gain control AGC must be turned off. Step 2: The user can select any gain value as long as it does over-drive the amplifier or exceed isolation requirements. Gain is automatically limited where conditions do not permit high gain. Select the DL and UL Gain values. Turn on the DL and UL path controls. APEX1933 USER MANUAL V1.2 Tech Support: 1-888-317-8766 32 5.7 GUI Status The status page display system, control, and alarm information. When you set any value on the Control page the change will be reflected on Status page. 5.7.1 System • Firmware version and location are displayed under Equipment Information. • The current band setting, set from the control page, is shown in bold font. 5.7.2 Operating • DL Path Monitor displays input from the donor antenna circuit, output power at equipment server antenna port, and downlink amplifier gain. • UL Path Monitor displays input from the server antenna circuit, output power at equipment donor port, and uplink amplifier gain. • Isolation Status shows isolation value (dB) between the donor antenna and server antennas. • Available gain allowed by isolation measurement. Available gain is derived from the antenna isolation value plus 15dB. Full system gain (43dB) is available if the antenna isolation value is at least 58dB. 5.7.3 Alarm • If an alarm occurs, the alarm LED on the equipment will turn on. APEX1933 USER MANUAL V1.2 Tech Support: 1-888-317-8766 33 Alarms shown on the status page will have orange (alarm) or green (normal) background. • Details for alarm events are displayed on the Alarm History page. For corrective action please refer to 6. Troubleshooting section. 5.8 File Update 5.8.1 MCU Firmware Download Step 1. For target, select “MCU“. Choose the correct target slot. If you are not sure, follow the LAN cable from the equipment receiving the update to the host equipment. The LAN port number on the host equipment is the slot number for the equipment receiving the update. Use the browse button to locate the update file. Step 2 MCU firmware file has a “.bin“ filename extension. Click Open. APEX1933 USER MANUAL V1.2 Tech Support: 1-888-317-8766 34 Step 3 Click Update. Step 4 When File update message appears and updating completed, go to Log-in page. Log-in and confirm the firmware version has been updated. APEX1933 USER MANUAL V1.2 Tech Support: 1-888-317-8766 35 5.8.2 Web GUI Download Step 1 Select WEB in File Update page and click Browse. Step 2 Select Firmware file which has “.web“ filename extension to download. Click Open. Step 3 Click Update. APEX1933 USER MANUAL V1.2 Tech Support: 1-888-317-8766 36 Step 4 When File update message appears and updating completed, go to Log-in page. 5.9 Attachment 5.9.1 Internet Network Setting 5.9.1.1 Window XP Step 1: Click the Start button and select My Network places. Step 2: Click View network connections. Step 3: Right-click on the Local Area Connection Step 4: Select Internet Protocol (TCP/IP) and click and select Properties to view the shortcut menu. Properties. APEX1933 USER MANUAL V1.2 Tech Support: 1-888-317-8766 37 Step 5: Check Obtain an IP address automatically and click OK. Step 6: Close all widows. 5.9.1.2 Windows Vista Step 1: Click the Start button and select Control panel. Step 3: Click Network and Sharing Center. APEX1933 USER MANUAL V1.2 Step 2: Click Network and Internet Step 4: Click View status of Local Area Connection. Tech Support: 1-888-317-8766 38 Step 5: Click Properties and a caution pop-up Step 6: Select Internet Protocol Version 4 (TCP/IPv4) window will appear. Click OK. and click Properties. Step 7: Check Obtain an IP address automatically and Click OK. APEX1933 USER MANUAL V1.2 Step 8: Close all windows. Tech Support: 1-888-317-8766 39 6. Troubleshooting Before contacting your service dealer, refer to the following guidelines. If the APEX1933 equipment does not work normally after completing the following troubleshooting, please contact your local dealer or R-tron America’s Tech support line (1-888-31R-TRON). External alarm lamps on the front of the equipment indicate current condition. Green lamp indicates power to the equipment, yellow indicates caution, and red indicates shut sown 6.1 LED Alarm Problem Cause Solution No LED on Power failure Check the power cord for secure connection Mobile device has Equipment poor performance. degraded or not available. service Login to the web GUI. Check the setting, alarm status and input/output power status. Gain, Input/ Output Most common cause for unstable gain and power is power or DC Current feedback oscillation are changing randomly or appear Oscillation to be unstable. brought on by insufficient antenna isolation. 1. Reduce equipment gain and/or AGC level. 2. Improve the field conditions that cause poor antenna isolation. Automatic shutdown occurs when the amplifier is over driven. The amplifier is most commonly overdriven by: 1. Oscillation due to poor antenna isolation. 2. High input power combined with high gain settings including high UL input from the mobile The red light is on. Automatic Shutdown device. User the alarm history page to determine the cause of the shutdown. Eliminate the root cause of the shutdown and restart the equipment. Technical Support Web site: www.r-tronamerica.com Toll Free: 888-317-8766 APEX1933 USER MANUAL V1.2 Tech Support: 1-888-317-8766 40 6.2 GUI Alarm Problem Check Point DC Current Solution If the same alarm occurs after reset Power, request technical support. Execute of System Reset (NCU) on Network Setup General Temperature page. If the same alarm occurs request technical support. ASD Heartbeat Check Isolation and DL/UL Input power.. Check the connection of the Remote NMS Cable. Check the interval of Heartbeat on the WEB GUI DL Input alarm can be the result of low signal level DL Input Power from the donor antenna circuit. Tune Femto output level and/or reduce line loss. Check DL input Power. DL Output Power If input power exceeds max input power install an attenuator on the donor antenna feed line. Downlink Return loss alarm is the result of o poorly matched antenna circuit. The equipment is almost never the DL Return Loss reason for return loss issues. A good quality 50 ohm load placed over the equipment server port or donor port will extinguish the alarm and prove the alarm is caused by some external antenna issue. If the UL Input Power is too high, suspect excessive Uplink UL Output Power mobile TX power. Determine root cause of high mobile TX power. APEX1933 USER MANUAL V1.2 Tech Support: 1-888-317-8766 41 6.3 Communication Alarm When you cannot login to the web GUI. Solution 1. Click My Network places Æ View network 2. Right-click on the Local Area Connection and then connections. Right-click on the Wireless click Disable. After clicking Disable, click Enable Network Connection and then click Disable. again. 3. Double click the Local Area Connection and then click the Support tab Æ Repair. APEX1933 USER MANUAL V1.2 Tech Support: 1-888-317-8766 42 Solution 4. Open the Internet Browser, select Tools Æ Internet Options. 5. Click Start and select Run. Type “ping 192.168.0.1-t” and click OK. Click Delete Files in the Temporary Internet files section. APEX1933 USER MANUAL V1.2 Tech Support: 1-888-317-8766 43 7. Specifications 7.1 RF Characteristics Electrical Specifications Parameter TX (Down-Link) RX (Up-Link) Frequency Range 1930 - 1995 MHz 1850 - 1915 MHz Service CDMA2000 or LTE(FDD) Service Channel Select Center frequency + BW (1M - 20MHz) Non-continuous 3 channel Nomal Input Power Range -10 ~ +15 dBm -68 ~ -40 dBm Composite Output Power Range 0 ~ 33 dBm ~ -25 dBm Gain Range 15 ~ 43 dB 15 ~ 43 dB AGC Range 28 dB Time the AGC must track only slow variations with time on the order of 100ms. Gain Ripple Noise Figure ± 1.0 dB Max Gain 5 dB (max) Min Gain 12 dB (max) > 50dBc at ± 1 MHz from band edge Roll-off > 50dBc at ± 2 MHz from band edge Propagation Delay 8 μs (max) IMD ≤ -13dBm Frequency stability < 0.02 ppm < 0.02 ppm Spurious Emission 885kHz 885kHz : -45dBc / 30kHz 1.25MHz 1.25MHz : -45dBc / 30kHz 1.98MHz 1.98MHz : -50dBc / 30kHz 2.25MHz 2.25MHz : -13dBm / 1MHz 4MHz 4MHz : -13dBm / 1MHz VSWR 1.5 : 1 (max) Impedance 50Ω APEX1933 USER MANUAL V1.2 Tech Support: 1-888-317-8766 44 7.2 Environmental Specification Specification Parameter Operating Temp -10˚C~50˚C (14˚F~122˚F) Humidity 5% ~ 95%RH Cooling method Convection. Environmental 7.3 Electrical Specification Parameter Specification Voltage AC 85-264V Current +24V/6.5A (150W) Frequency 50/60(47-63)Hz 7.4 Mechanical Specification Parameter Specifications RF connectors N-female x 2 Dimensions (WxHxD) 9.35 * 16.8 * 5.67 Inch 242 * 426 * 144 mm Weight 44.09 lb 20 Kg max APEX1933 USER MANUAL V1.2 Remark W*D*H Tech Support: 1-888-317-8766 45 8. Appendix 8.1 US PCS Channel APEX1933 USER MANUAL V1.2 Tech Support: 1-888-317-8766 46 8.2 Warranty LIMITED WARRANTY This product, as supplied and distributed by R-tron, in the original carton, is warranted by R-tron against manufacturing defects in materials and workmanship for a limited warranty period of: Five (5) Year Parts and Labor This limited warranty begins on the original date of purchase, and is valid only on products purchased and used in the United States. R-tron will repair or replace this product, at our option and at no charge as stipulated herein, with new or reconditioned parts or products if found to be defective during the limited warranty period specified above. All replaced parts and products become the property of R-tron and must be returned to R-tron. Replacement parts and products assume the remaining original warranty. This limited warranty covers manufacturing defects in materials and workmanship encountered in normal, and except to the extent otherwise expressly provided for in this statement, use of this product, and shall not apply to the following, including, but not limited to: damage which occurs in installation; applications and uses for which this product was not intended; altered product or serial numbers; cosmetic damage or exterior finish; accidents, abuse, neglect, fire, water, lightning or other acts of nature; use of products, equipment, systems, utilities, services, parts, supplies, accessories, applications, installations, repairs, external wiring or connectors not supplied or authorized by R-tron which damage this product or result in service problems; or incorrect electrical line voltage, fluctuations and surges; customer adjustments and failure to follow operating instruction. R-tron does not warrant uninterrupted or error-free operation of the product. THERE ARE NO EXPRESS WARRANTIES OTHER THAN THOSE LISTED AND DESCRIBED ABOVE, AND NO WARRANTIES WHETHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, SHALL APPLY AFTER THE EXPRESS WARRANTY PERIODS STATED ABOVE, AND NO OTHER EXPRESS WARRANTY OR GUARANTY GIVEN BY ANY PERSON, FIRM OR CORPORATION WITH RESPECT TO THIS PRODUCT SHALL BE BINDING ON R-tron. 8.3 Return Material Authorization (RMA) Procedure The return and exchange of products are not allowed without prior approval from R-tron America, Inc. Please follow the exchange procedure below. APEX1933 USER MANUAL V1.2 Tech Support: 1-888-317-8766 47 1. Call Tech Support for troubleshooting. 2. If the device has hardware problem, R-tron will replace it if it is within warranty. A RMA number will be issued for the return. 3. R-tron will ship the replacement unit with a return shipping label. 4. The customer must return the product using the original packaging, including all accessories and/or parts. APEX1933 USER MANUAL V1.2 Tech Support: 1-888-317-8766 48
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No XMP Toolkit : 3.1-702 Producer : Acrobat Distiller 7.0.5 (Windows) Create Date : 2014:03:12 16:43:37+09:00 Creator Tool : PScript5.dll Version 5.2.2 Modify Date : 2014:03:12 18:02:22+09:00 Metadata Date : 2014:03:12 18:02:22+09:00 Format : application/pdf Creator : User Title : Microsoft Word - APEX1933 User's Manual_20140120_V.1.2.docx Document ID : uuid:36ab4049-6363-4b40-a60c-ced83c62c951 Instance ID : uuid:83b96172-1305-4654-81a0-4c633a687016 Page Count : 52 Author : UserEXIF Metadata provided by EXIF.tools