User Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 1185087 |
| Application ID | ppoaXR5RILei7I3wRT1JiQ== |
| Document Description | User Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 169.31kB (2116430 bits) |
| Date Submitted | 2009-10-16 00:00:00 |
| Date Available | 2009-10-16 00:00:00 |
| Creation Date | 2009-09-30 13:04:04 |
| Producing Software | Acrobat Distiller 6.0.1 (Windows) |
| Document Lastmod | 2009-10-16 14:01:08 |
| Document Title | untitled |
WiMAX-23 RSN-WiMAX-23 L/H User’s Manual Please read this manual before operating this product. After you finish reading this manual, store it in a safe place for future reference. User’s Manual Warning ! Any changes or modifications to the equipment not expressly approved by the party responsible for compliance could void user’s authority to operate the equipment. Note ! This unit was tested with shielded cables on the peripheral devices. Shielded cables must be used with the unit to insure compliance. Important ! To comply with RF exposure requirement, the antenna must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. CAUTION This equipment is indoor use and all the communication Proprietary & Confidential Page 2 Issue: 1.0 Notice Trademark R-tron is a registered trademark of R-tron Inc. Other products and company names mentioned here in this manual might be trademarks or trade names of their respective owners. Copyright Copyright R-tron Inc. 2000-2009 All Rights Reserved Any reproduction, distribution, or revisions of any or all portions of this manual is prohibited without written permission from R-tron Inc. Notice This document describes the specifications, installation, and operation of the WiMAX repeater. Hardware and software mentioned in this document are subject to continuous development and improvement. Consequently, there may be minor discrepancies between the information in the document, performance, and design of the product. Specifications, dimensions, and other statements mentioned in this document are subject to change without notice. Questions or Comments Address: R-tron Inc. 6402 College Boulevard, Overland Park, KS 66211 Phone: +1-913-344-9977, 1-888-31R-TRON Fax: +1-913-344-9988 e-mail: info@r-tronamerica.com Website: www.rtronamerica.com Safety Precautions Opening the WiMAX equipment could result in electric shock and may cause severe injury. Connect the equipment frame ground to the building ground. Operating the WiMAX with antennas in very close proximity facing each other can lead to severe damage to the repeater. RF EXPOSURE INFORMATION A minimum separation distance of 7.9 inches (20cm) must be maintained between the user and the external antenna of the repeater to satisfy FCC RF exposure requirements. For more information about RF exposure, please visit the FCC website at www.fcc.gov This equipment is for indoor use only and enables the communication wiring to communicate inside the building. Contents Glossary .......................................................................................................................................... 5 1. Introduction .............................................................................................................................. 6 2. Description. ............................................................................................................................... 7 2.1. Main Unit Overview...…………………………………………………………….………………………………….………………..7 2.2. Internal Configuration………………………………………………………….…………………………………………………….8 2.2.1. Block diagram……………………………………………………………….….…………………………………………………..9 2.2.2. AC-DC Adaptor…………………………………………………………………………………………………………………..10 2.2.3. MCU (Main Control Unit')……………………………………………………………….…………………………………11 3. Hardware Installation............................................................................................................12 3.1. Check List of Items…………………………………………………………………………………………………………………..12 3.2. Mounting………………………………………………………………………………………………………………………………….13 3.3. Grounding…..…………………………………………………………………………………………………………………………….15 3.4. Cable Connection……………………………………………………………………………………………………………………..16 3.5. Power On…………………………………………………………………………………………………………………………………..16 4. Operation.................................................................................................................................18 4.1. System Requirements………………………………………………………………………………………………………………18 4.2. Network Setup…………………………………………………………………………………………………………………………18 4.2.1. Windows XP……………………………………………………………………………………………………………………….18 4.2.2. Windows 2000…………………………………………………………………………………………………………………..20 4.2.3. Windows Vista…………………………………………………………………………………………………………………..22 4.3. System Log in………………………………………………………………………………………………………………………….26 4.4. System Setup..…………………………………………………………………………………………………………………………26 5. Troubleshooting…………………………………………………………………………………………..35 6. Specifications……………………………………………………………………………………………….40 7. Appendix…….……………………………………………………………………………………………….41 Glossary The following is a list of abbreviations and terms used in this manual. Abbreviation AC ANT ATT WiMAX DC DL GND GUI LED PLL PSU RF RSSI TEMP TTG/RTG UL VSWR Definition Alternating Current Antenna Attenuator / Attenuation Worldwide Interoperability for Microwave Access Direct Current Downlink Grounding Graphic User Interface Light Emitting Diode Phase-locked loop Power Supply Unit Radio Frequency Received Signal Strength Indication Temperature Transmit/Receive and Receive/Transmit Transition Gaps Uplink Voltage Standing Wave Ratio ALC (Automatic Level Control) ALC feature prevents the repeater from exceeding its maximum output power by reducing the gain automatically. ALC is used to adjust the gain to an appropriate level for a range of input signal levels. ASD (Automatic Shutdown) Automatic shut down protects the repeater from the oscillation or excessive input signal and eliminates any degradation to the network. There are three parameters: ASD Level, ASD Time, and ASD Iteration. If the output power gets higher than “ASD LEVEL”, the repeater will shut down for “ASD TIME” seconds and then it will turn the amp back on to measure the output power again. If this repeats at “Iteration” times, the repeater will shut down completely. 1. Introduction WiMAX repeaters are used to fill out areas in the WiMAX mobile systems, such as base station fringe areas, business and industrial buildings, etc. WiMAX repeaters receive signals from a base station, amplify and retransmit the signals to the mobile stations. It also receives, amplifies and retransmits signals in the opposite direction. Both directions are served simultaneously with the following features A. RSN-WiMAX-23 ◆ Band Select >> designated low and high segment Bandwidth [Low: AB, BC, CD / High: EF, FH, HG] ◆ Easy and Quick Installation >> Web-based GUI >> Plug and Play – DHCP Server @ Local Port an DHCP Client >> Easy Setup(Automatic) >> Real Time Isolation Detection ◆ Auto Level Control & Auto Shut Down - This repeater allows the Web Server and Web GUI to communicate with a PC, except for the function of reporting through the radio network. There is only one physical RJ-45 port: • The local port provides an on-site access to the repeater. - DHCP server at the local port enables Plug and Play by automatically assigning the IP address to the user’s computer - Parameter setup is only a Power ON away • Main features of Easy Setup is to set up the output power level along the each time segment of DL/UL path gain after receiving a sync signal from an input signal. Until it is synchronized, it does not progress to the next step where it will measure the isolation and limit the maximum gain accordingly. This will also enable Auto Level Control as well as Auto Shut Down. These two features are strongly recommended to prevent uncontrolled power output, which could have an adverse impact on the RF network and the repeater. For example, ALC will automatically apply attenuation when the input signal strength is increased due to the new base station deployment near the repeater site 2. Description 2.1 Main Unit Overview 1. Ground Contact: Connects the repeater frame ground to the building ground. 2. DC In: DC power Jack. 3. Server Antenna Port: Connects the server antenna 4. Donor Antenna Port: Connects the donor antenna. 5. Alarm LED: When the On-site Alarm occurs, the LED turns on. When it operates normally, the green LED turns on. 6. UL Gain Ctrl: To control only the UL Path gain through a simple switch combination. 7. Power On/Off S/W: Inputting Power On/Off. 8. Local Access Port: To monitor & control through the UTP LAN Cable and PC, and connect to the WEB GUI. 9. DC Input Jack: External AC-DC Adaptor Input Port. 2.2 Internal Configuration MCU Sync Detec 1. MCU (Main Control Unit) 2. Sync Detec 2.2.1 Block Diagram The following diagram explains how the WiMAX repeater amplifies the signal. 2.2.2 AC-DC Adaptor The AC-DC adaptor supplies a steady DC power to the WiMAX equipment by drawing power from the general in-wall AC outlets. Specification Item Environmental Specification Operating Temp -0˚C~40˚C (32˚F~104˚F) Humidity 20%~90%RH Cooling method Convection. Voltage AC110~240V Current +12V/6.67A Frequency Input Current 40~63Hz typical 0.25mA max.@ 254Vzc/50Hz 10 2.2.3 MCU (Main Control Unit) The MCU (Main Control Unit) is the control unit of the WiMAX repeater. It controls and monitors operational parameters. It is also responsible for generating alarms, keeping event logs and performing many other functions. CON 5 CON 11 Pin Map Port Connected to CON 11 RFU Control 1 CON 12 RFU Control 2 CON 5 Ethernet 11 3. Hardware Installation The installation procedure is as follows: • Check List of Items • Mounting • Grounding • RF Cable Connection • Power On 3.1 Check List of Items Index Items Quantity Repeater AC-DC Adaptor UTP Cross LAN Cable AC Cord Anchor Bolts CD of the User’s Manual Quick Guide Item Figure Repeater AC Cord AC- DC Adaptor CD of the User s Manual Anchor Bolts 12 UTP Cross LAN Cable Quick Guide 3.2 Mounting WiMAX repeaters are easy to mount using the assembled mounting bracket, which has 4 holes for the provided 5/16” fixing screws. Step 1: Drill holes directly through the template. Step 2: Install the set anchor bolts or the plastic anchor bolts on the holes. Step 3: Attach the mounting bracket to the wall using provided bolts or extra screws. 13 Step 4: Lean the WiMAX to hang the topside of the Guide Ring on the mounting bracket, and push toward the wall to mount. Step 5: Fix the WiMAX using the 6 screws provided. 14 3.3 Grounding A rod on the left side is intended for a building ground. Connect the ground cable to the rod. 15 3.4 RF Cable Connection Step 1: Connect a cable from a donor antenna to the Donor Antenna Port. Step 2: Connect a cable from a repeater’s service antenna to the Server Antenna Port. 3.5 Power On Step 1: Connect the power cord. Step 2: Plug the power cord into a wall outlet. Step 3: Turn on the power switch. This repeater follows the below set-up algorithm automatically right after the power is ON 16 WiMAX has a function where the gain can be set to a MAX value of -15dB by using an external switch combination. Refer to the following diagram in regards to the switch combination. Attenuation Value Switch Combination 0dB -1dB -2dB -3dB -4dB -5dB -6dB -7dB -8dB -9dB -10dB -11dB -12dB -13dB -14dB -15dB 17 4. Operation 4.1 System Requirements WiMAX operates on a customer provided PC based platform with the following system requirements: • Windows® 2000, Windows® XP or Windows® Vista • Internet Explorer 6.0(Recommended) or higher • 128 MB RAM or higher • Pentium Ⅲ processor or higher • RJ-45 jack required 4.2 Network Setup 4.2.1 Windows XP Step 1: Click the Start button and My Network Places. Step 2: Click View network connections. 18 Step 3: Right-click on the Local Area Connection and select Properties to view the shortcut menu. Step 4: Select Internet Protocol (TCP/IP) and click Properties. Step 5: Check Obtain an IP address automatically and click OK. Step 6: Close all widows. 19 4.2.2 Windows 2000 Step 1: Click the Start button, point to Settings, and then click Network and Dial-up Connections. Step 2: Right-click Local Area Connection to see a shortcut menu and click Properties. 20 Step 3: Select Internet Protocol (TCP/IP) and click Properties. Step 4: Check Obtain an IP address automatically and click OK. Step 5: Close all windows. 4.2.3 Windows Vista 21 Step 1: Click the Start button and Control Panel. Step 2: Click Network and Internet. Step 3: Click Network and Sharing Center. 22 Step 4: Click View status of Local Area Connection. Step 5: Click Properties and a caution pop-up window will appear. Click OK. 23 Step 6: Select Internet Protocol Version 4 (TCP/IPv4) and click Properties. Step 7: Check Obtain an IP address automatically and click OK. 24 Step 8: Close all windows. 25 4.3 System Login Open your Web browser and type “192.168.0.1” into the URL address box. Then press the Enter key. 4.4 System Setup 4.4.1 Clock The clock automatically sets up to the PC’s time setting when you click APPLY. 4.4.2 Auto Refresh This sentence makes no sense. You should change it to: “When you click on the Auto Refresh button, the Web GUI screen automatically updates itself every 5 seconds.” 4.4.3 Control WiMAX-23 does not need to Log-In. The user can control the repeater directly through the WEB GUI connection. 26 Solution 1. Easy setup [Recommended] Step 1 Select the operating Band and click APPLY. Step 2 Easy Setup Easy Setup proceeds to: ∙ Data initial execution ∙ Sync signal acquisition ∙ HPA ON ∙ ALC gain set ∙ ASD ON ∙ ALC ON to obtain Maximum DL Output Power 23dBm[Default] or Maximum Gain 80dB. ∙ Real time isolation check Click Automatic Easy Setup. Easy Setup feature detects Sync signals from the input RF signal. If the Easy Setup processor does not receive a sync signal, it does not progress any further and performs the sync signal acquisition step. 27 Step3 Click OK Step 4 Setup will automatically begin. This process takes approximately 1 minute. Result 1 Constant Maximum DL Output Power 23dBm If the DL Input Power >= -57dBm 28 Result 2 Maximum Gain 95dB if the DL Input Power < -57dBm ∙ Automatic Level Control: Type under 23 and then click APPLY and ON. This is an example case for a repeater with 23dBm maximum output power, 80dB maximum gain/35dB gain control range, Æ If the signal -47dBm and the ALC is set as 23dBm, the gain will be 70dB to adjust to the output power. If the input signal is -60dBm, the output power will be 20dBm by the limitation of the maximum gain even though the ALC is set as 23dBm 29 ∙ Automatic Shutdown: Type the desired value for dBm, seconds, and times and then Click APPLY and ON. [Example] A repeater with 23dBm Maximum Output Power, 80dB Maximum Gain/35dB gain control range, assuming ASD Level: 25dBm, ASD Time, ASD Count are already fixed at 3seconds, 10times. If the composite output power is 25dBm(ASD Level) and higher, the repeater will shutdown for 3seconds(ASD Time). If the shutdown occurs 10times(ASD Count), the 11th shutdown will be permanent. The repeater automatically runs Easy Setup. After that, it is activated with the re-calculated antenna isolation value. 30 Solution 2. DL Output Power < Max. 23dBm Step 1A Repeat Step 1 through Step 4 Step 2A Change the level at Automatic Level Control and then APPLY Result Constant output power set as the ALC Level 31 Solution 3. Manual Gain Setting Gain [Not Recommended] Step 1B Repeat Setps1 through 4 Step 2B Read the DL Input Power and the gain controlled by the Easy Setup. Step 3B Turn off HPA Step 4B ALC must be turned off 32 Step 5B Change the DL gain and the UL gain Step 6B Turn on HPA Result DL and UL gain are fixed and the output power depends on the input power. 33 Alarms∙ Alarm : If an alarm occurs, the alarm LED on the repeater will turn on. Please refer to the troubleshooting section of this manual. ∙ No Change in values on the alarm range is recommended. 34 5. Troubleshooting Before contacting your service dealer, please make sure you refer to the following guide. If the WiMAX repeater does not work normally after completing the following troubleshooting, please contact your local dealer or R-tron America’s Tech support line (888-31R-TRON). The alarm information is displayed by the LED lights on the repeater. Problem Cause No LED on Alarm LED On Solution Check the power cord for secure connection. In/output power alarm Over input, Over Output, out of sync; occur and lost a sync In case of these 3, the alarm LED is on, signal If the alarm is by over input or over output, the ASD algorithm is applied. If the RF environment is normal, the LED is automatically turned OFF. For Out of sync, it searches the sync for up to 1 hour when the synch is lost. After that, HPF is turned OFF. If it still searching for the sync. At this moment, the status of TDD S/W maintains DL. If the sync is obtained again, HPA is back ON and the ALARM LED is turned OFF. Alarm LED Occurs at the lowest When the alarm occurs by low input and not by flickering limit of output the isolation ATT, it is flashing. When the output power comes back to normal, the LED is turned OFF. When the WiMAX’s selected band is different from the actual service band, service is impossible. 35 Problem Cause Solution Cannot 1. Click My Network places Æ View network communicate with connections. Right-click on the Wireless the repeater. Network Connection and then click Disable. 36 Problem Cause Solution 2. Right-click on the Local Area Connection and then click Disable. After clicking Disable, click Enable again. 3. Double click the Local Area Connection and then click Support tap Æ Repair. 37 Problem Cause solution 4. Open the Internet Browser and then select Tools Æ Internet Options. Click Delete Files button in the Temporary Internet files section. 38 Problem Cause Solution 5. Click Start and select Run. Type 39 “ping 192.168.0.1-t” and click OK. 6. Specifications RF Characteristics Electrical Specifications Specifications Parameter RX(Up-Link) TX(Down-Link) Frequency Range 2502 ~ 2690MHz Output Power / total +23 dBm Gain 80 dB Gain Control Range(Input ALC) 35 dB / 1dB step Gain Control Range 30 dB / 1dB step Input Limit ALC(H/W ALC) 10 dB / 1dB step Noise Figure Max/Middle. Gain ≤ 5.0 dB ≤ 5.0 dB Min. Gain ≤ 12.0 dB ≤ 12.0 dB ≤ 3 dB Gain Ripple ACP Spurious emission Remark 188M B.W Peak-to-Peak Fc ±16.5MHz ≤ -13 dBm RBW :100kHz Fc ±18.5MHz ≤ -13 dBm RBW: 1MHz Fc ±20MHz ≤ -37 dBm RBW: 1MHz Fc ±23MHz ≤ -37 dBm RBW: 1MHz 1850 ~ 1995 MHz Below the noise floor 806-826MHz and 851-869MHz Below the noise floor 896-901MHz and 935-940MHz Below the noise floor Contiguous Capability Fixed 30MHz only EVM 5% Frequency error 0.05ppm Propagation Delay < 5 us Return Loss / VSWR > 14dB / < 1.5 RF Connector Type-N Female Impedance 50Ω Electrical & Environmental Specification Parameter Environment Specifications Specifications Cooling Convection Operating Temperature -10 ~ +50 ℃ Relative Humidity 5 ~ 95% 40 Remark Mechanical Specification Mechanical Specifications Specifications Parameter Dimensions (WxHxD) Weight 210 x 290 x 74 mm 8.27 x 11.4 x 2.9 inch 5Kg(11lbs) 7. Appendix WiMAX Band Frequency chart * AB/BC/CD/EF/FH/HG Band BRS Band Frequency Range Band A 2502 ~ 2518.5 MHz Band B 2518.5 ~ 2535 MHz Band C 2535 ~ 2551.5 MHz Band D 2551.5 ~ 2568 MHz Band E 2624 ~ 2640.5 MHz Band F 2640.5 ~ 2657 MHz Band G 2657 ~ 2673.5 MHz Band H 2673.5 ~ 2690 MHz 41 Remark Warranty LIMITED WARRANTY This product, as supplied and distributed by R-tron, in the original carton, is warranted by R-tron against manufacturing defects in materials and workmanship for a limited warranty period of: Five (5) Year Parts and Labor This limited warranty begins on the original date of purchase, and is valid only on products purchased and used in the United States. R-tron will repair or replace this product, at our option and at no charge as stipulated herein, with new or reconditioned parts or products if found to be defective during the limited warranty period specified above. All replaced parts and products become the property of R-tron and must be returned to R-tron. Replacement parts and products assume the remaining original warranty. This limited warranty covers manufacturing defects in materials and workmanship encountered in normal, and except to the extent otherwise expressly provided for in this statement, use of this product, and shall not apply to the following, including, but not limited to: damage which occurs in installation; applications and uses for which this product was not intended; altered product or serial numbers; cosmetic damage or exterior finish; accidents, abuse, neglect, fire, water, lightning or other acts of nature; use of products, equipment, systems, utilities, services, parts, supplies, accessories, applications, installations, repairs, external wiring or connectors not supplied or authorized by R-tron which damage this product or result in service problems; or incorrect electrical line voltage, fluctuations and surges; customer adjustments and failure to follow operating instruction. R-tron does not warrant uninterrupted or error-free operation of the product. THERE ARE NO EXPRESS WARRANTIES OTHER THAN THOSE LISTED AND DESCRIBED ABOVE, AND NO WARRANTIES WHETHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, SHALL APPLY AFTER THE EXPRESS WARRANTY PERIODS STATED ABOVE, AND NO OTHER EXPRESS WARRANTY OR GUARANTY GIVEN BY ANY PERSON, FIRM OR CORPORATION WITH RESPECT TO THIS PRODUCT SHALL BE BINDING ON R-tron. 42 Return Material Authorization(RMA) Procedure The return and exchange of products are not allowed without prior approval from R-tron America, Inc. Please follow the exchange procedure below. 1. Call Tech Support for troubleshooting. 2. If the device has a hardware problem, R-tron will replace it if it is within warranty. A RMA number will be issued for the return. 3. R-tron will ship the replacement and a return label will be provided. 4. The customer must return the product using the original packaging, including all accessories and/or parts. 43
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes XMP Toolkit : 3.1-702 About : uuid:d0133c24-577b-4edb-90f9-420856018be3 Producer : Acrobat Distiller 6.0.1 (Windows) Modify Date : 2009:10:16 14:01:08+09:00 Create Date : 2009:09:30 13:04:04+09:00 Metadata Date : 2009:10:16 14:01:08+09:00 Document ID : uuid:e3e8f3bc-729b-4da2-96b6-65125cf4f242 Instance ID : uuid:6a530b5c-89aa-450a-8ed5-e296dac38e33 Format : application/pdf Title : untitled Has XFA : No Page Count : 44EXIF Metadata provided by EXIF.tools