R tron SNIDEN25DC Wireless Booster User Manual

R-tron Inc. Wireless Booster

Manual rev

R-tron Proprietary & Confidential Page 1 Issue: 1.0 RSN-iDEN-25-DC Manual R-tron Inc.
1 User’s ManualSafety PrecautionsSafety PrecautionsWarningOpening the iDEN MINI could result in electric shock and may cause severe injury.WarningConnect the equipment frame ground to building ground.Warning Operating the iDEN MINI with antennas in very close proximity facing each other could lead to severe damage to the Booster.CautionRF EXPOSURE INFORMATIONA minimum separation distance of 7.9 inches (20cm) must be maintained between the user and the external antenna of Booster to satisfy FCC RF exposure requirements. For more information about RF exposure, please visit the FCC website at www.fcc.govCautionThis equipment is for indoor use and enables the communication wiring to communicate only inside the building.RSN-iDEN-25-C (0213).indd 1 2008-02-13 ¿ÀÈÄ 2:53:04
System Manual RSN-iDEN-25-DC R-tron Proprietary & Confidential Page 2 Issue: 1.0 1. Introduction RSN-iDEN-25-DC Booster is used to fill out uncovered areas in iDEN mobile systems, such as base station fringe areas, road tunnels, business and industrial buildings, etc. An RSN-iDEN-25-DC Booster receives signals from a base station, amplifies and retransmits the signals to mobile stations. Also it receives, amplifies and retransmits signals in the opposite direction. Both directions are served simultaneously. To be able to receive and transmit signals in both directions, the Booster is connected to a donor antenna directed towards the base station and to a service antenna directed towards the area to be covered. Control of the Booster is performed using a desktop or notebook loaded through the RJ-45 Jack DC Outlet for external device Remote port Local port Alarm LEDs 900MHz DL Output -30dB CPL Server antenna port 800MHz DL Output-30dB CPL Donor antenna port Modem AntAC in and Switch 900MHz UL Output-30dB CPL 800MHz UL Output -30dB CPL Ground contact
System Manual RSN-iDEN-25-DC R-tron Proprietary & Confidential Page 3 Issue: 1.0 which can communicate with the Booster. Remote operation can be performed. RSN-iDEN-25-DC Booster work as bi-directional amplifiers. A Booster receives, amplifies, and retransmits signals inbound and outbound simultaneously, i.e. from the base station via the Booster to the mobile stations and from the mobile stations via the Booster to the base station. The Booster can be connected to a donor antenna directed towards the base station, and to a server antenna directed towards the area to be covered. The donor antenna is connected to the Booster with type-N connector. On the other hand, the server antenna is an external antenna. The RSN-iDEN-25-DC Booster are controlled by powerful microprocessors. Operational status LEDs are visible on the bottom of the Booster. The Booster works with convection cooling without fan because it has a radiator behind the body of RSN-iDEN-25-DC. Operational parameters, such as gain, power levels, alarm condition, Automatic Gain Control condition, etc. are set using a desktop or notebook and the RJ-45 jack, which communicate, either locally or remotely via the UTP(Unshielded Twisted Pair Wire) cable, with the Booster.
System Manual RSN-iDEN-25-DC R-tron Proprietary & Confidential Page 4 Issue: 1.0 2. System Design 2.1 RSN-iDEN-25-DC Specification 2.1.1 Mechanical Specification Parameter Specification RF Ports N-female x 2, SMA-female x 5 Size 13.98 X 14.37 X 7.62(inch), 355 X 365 X 193.5(mm) Weight 17.154Kg(37.82lbs) <Table 2-1> Mechanical Specification DONORANTENNAMODEM ANTDANGERRISK OF ELECTRIC SHOCK110 -125VacAC INSERVERANTENNANoteexternal devices onlyPower outlet for compatiblehttp://192.168.0.1:83LOCALMAX 2A+12Vdc or -12VdcDC OUTREMOTEALARM800MHzUL Out put-30dB CPL.900MHzDL Output-30dB CPL.800MHzDL Output-30dB CPL.900MHzUL Out put-30dB CPL.COMPLIES WITH PART 90, FCC RULES.MAKER SERIAL NO. / DATE : FCC REG. NO. POWER PRODUCT PART NUMBER110 -125Vac , 60Hz , 2ARSN- iDE N-25-CR-tron lnc.:: ST ESNI DEN2 5C::MADE IN KOREAI.T.E31CYE258109
System Manual RSN-iDEN-25-DC R-tron Proprietary & Confidential Page 5 Issue: 1.0 2.1.2 Electrical & Environmental Specification A. Spectrum Characteristics Parameter iDEN 800 iDEN 900 Operating Frequency DL 851MHz - 869MHz 935MHz ~ 940MHz UL 806MHz ~ 824MHz 896MHz ~ 901MHz Roll off characteristics DL & UL ≥ 65dBc @±500kHz from each edge of operating band (in all temperature) Flatness ≤ 2.5dB (in all temperature) Gain DL & UL 50dB to 80dB(in all temperature) Delay DL & UL 8.0µs Max. VSWR DL & UL 1.5 Max. Composite Output Power DL 25dBm UL 25dBm UL Noise Figure 5dB Max. (@80dB Gain) 12dB Max. (@50dB Gain) <Table 2-2> RF Specification
System Manual RSN-iDEN-25-DC R-tron Proprietary & Confidential Page 6 Issue: 1.0 B. Environmental specification Item Standard Remark Power supply 110V~125V, 60Hz Operating temperature -10℃ ~ 50℃ Humidity 95 % <Table 2-3> System Features
System Manual RSN-iDEN-25-DC R-tron Proprietary & Confidential Page 7 Issue: 1.0 2.2 Sub Unit Overview RSN-iDEN-25-DC is composed of the following sub units:  UDC(Up Down Converter)  HPAs(High Power Amplifiers)  Multiplexers  Main Control Unit (MCU)  Power Supply Unit (PSU)  EMI Filter UDC MCU DL HPA Multiplexers UL HPA EMI Filter PSU
System Manual RSN-iDEN-25-DC R-tron Proprietary & Confidential Page 8 Issue: 1.0 2.2.1 Block diagram The following, Figure explains how the RSN-iDEN-25-DC serves signals. 2.2.2 UDC Modules The UDC Module is basically a bi-directional amplifier that sharply filters out unwanted noise.
System Manual RSN-iDEN-25-DC R-tron Proprietary & Confidential Page 9 Issue: 1.0 2.2.3 Multiplexers <Rear view> <Top view> <Front view>
System Manual RSN-iDEN-25-DC R-tron Proprietary & Confidential Page 10 Issue: 1.0 2.2.4 Main Control Unit (MCU) MCU is the control unit of RSN-iDEN-25-DC. It controls and monitors operational parameters. It also generates alarms, an event log and many other functions of the RSN-iDEN-25-DC. *Pin Map* Port Connected to J6 MCU Vcc(+12V) J7 - J8 PSU Alarms / Status LEDs J9 iDEN 900 J10 iDEN 800 P1 Local P2 Remote J9J10
System Manual RSN-iDEN-25-DC R-tron Proprietary & Confidential Page 11 Issue: 1.0 2.2.5 Power Supply The Power Supply Unit (PSU) supplies a steady DC power to RSN-iDEN-25-DC by drawing power from the general in-wall AC outlets *Specification* Item Specifications Environmental Operating Temp -10℃~ 50℃ Humidity 5%~95% Cooling method Convection Voltage AC110~125V Current 4A Max / 6.5V, 12V, -12V , 27VDC Frequency 60Hz typ Leakage Current 0.5mA max.@110V AC
System Manual RSN-iDEN-25-DC R-tron Proprietary & Confidential Page 12 Issue: 1.0 2.2.6 High Power Amplifiers (HPAs) The High Power Amplifiers the transmitted signal from a base station at the final stage of the Booster and vice versa. <iDEN UL HPA> <iDEN DL HPA>
System Manual RSN-iDEN-25-DC R-tron Proprietary & Confidential Page 13 Issue: 1.0 2.2.6 EMI Noise Filter 2.2.7 Communication & LED Board
System Manual RSN-iDEN-25-DC R-tron Proprietary & Confidential Page 14 Issue: 1.0 * Hardware Installation 1. Setting for Command and Control * iDEN MINI operates on a customer provided PC based platform with the following system requirements. Windows® XP Strong recommended 128 MB RAM or more Pentium Ⅲ processor or more keyboard RJ-45 jack Step 1 Open My Network Places. Step 2 Click the “View network connections”.
System Manual RSN-iDEN-25-DC R-tron Proprietary & Confidential Page 15 Issue: 1.0 Step 3 Push the right button of mouse and select the properties. Step 4 Click the properties of TCP/IP.
System Manual RSN-iDEN-25-DC R-tron Proprietary & Confidential Page 16 Issue: 1.0 Step 5 Set the values and OK as the following. Close all windows. Step 6 Open a new explorer window.
System Manual RSN-iDEN-25-DC R-tron Proprietary & Confidential Page 17 Issue: 1.0 Step 7 Type http://192.168.0.1:83 in the address box and press “Enter” key. Step 8 Login with “administrator” of ID and “1234” of password and “OK”.
System Manual RSN-iDEN-25-DC R-tron Proprietary & Confidential Page 18 Issue: 1.0 2. Command and Control on the Web GUI. A. iDEN 800. a. To control the iDEN 800, check the box of iDEN 800. b. The operating bandwidth, 18MHz-bandwidth and 7MHz-bandwidth, is possibly selected. Select the operating bandwidth and push the “APPLY” and check the bandwidth.
System Manual RSN-iDEN-25-DC R-tron Proprietary & Confidential Page 19 Issue: 1.0 c. The operating frequency is able to be selected. Select the operating frequency and push the “APPLY” and check the bandwidth and frequency.
System Manual RSN-iDEN-25-DC R-tron Proprietary & Confidential Page 20 Issue: 1.0 B. iDEN 900. a. To control the iDEN 900, check the box of iDEN 900. b. On the iDEN 900, 5MHz-bandwith is only available. Select the operating frequency and push the “APPLY” and check the bandwidth and frequency.
System Manual RSN-iDEN-25-DC R-tron Proprietary & Confidential Page 21 Issue: 1.0 C. DL and UL gain setting. a. Set the DL gain and UL gain, 50dB to 80dB, and push the “APPLY” button. * Set the gain of iDEN 900 as same as the iDEN 800 gain setting.
System Manual RSN-iDEN-25-DC R-tron Proprietary & Confidential Page 22 Issue: 1.0 D. HPA on and off. a. Press the “ON” and “OFF” and check the status. The maximum output power for operating is +25dBm on both DL and UL.
System Manual RSN-iDEN-25-DC R-tron Proprietary & Confidential Page 23 Issue: 1.0 * Reference The Operating Bandwidth & Frequencies Bandwidth Operating Frequency iDEN 800 18MHz-bandwidth Downlink 851~869MHz 851~868.8MHz 851~868.6MHz Uplink 806~824MHz 806~823.8MHz 806~823.6MHz 7MHz-bandwidth Downlink 862~869MHz 862~868.8MHz 862~868.6MHz Uplink 817~824MHz 817~823.8MHz 817~823.6MHz iDEN 900 5MHz-bandwidth Downlink 935~940MHz 935~939.8MHz 935~939.6MHz Uplink 896~901MHz 896~900.8MHz 896~900.6MHz Operating bandwidth and Frequencies of iDEN

Navigation menu