R tron SPAPE030M PCS Band In-Building CDMA Booster User Manual

Download:
Mirror Download [FCC.gov]
Document ID	664072
Application ID	XhxGLSUVNVcVkfchX4yppg==
Document Description	Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	43.64kB (545530 bits)
Date Submitted	2006-06-01 00:00:00
Date Available	2006-06-01 00:00:00
Creation Date	2006-05-11 15:17:08
Producing Software	Acrobat Distiller 6.0 (Windows)
Document Lastmod	2006-05-23 20:26:18
Document Title	untitled

User’s Manual
of
Advanced MINI 30
RSP-APE-030M
User’s Manual
Contents
1. Overview ------------------------------------------------------------------------ 3
2. Specifications ---------------------------------------------------------------- 4
2.1 System specifications ------------------------------------------------------- 4
2.2 Antenna specifications ------------------------------------------------------ 5
2.3 Donor Antenna Diagrams -------------------------------------------------- 6
2.4 Distributor Antenna Diagrams -------------------------------------------- 6
3. System Configuration ---------------------------------------------------- 7
3.1 Block Diagram -----------------------------------------------------------------7
4. Installation ----------------------------------------------------------------------8
4.1 Installation Overview --------------------------------------------------------8
4.2 Safety
------------------------------------------------------------------------8
4.3 Installation information-1 ---------------------------------------------------9
4.4 Installation information-2 ---------------------------------------------------9
5. Graphic User Interface (for maintenance) ------------------- 10
5.1 GUI Overview --------------------------------------------------------------- 10
5.2 Preliminary steps for GUI Execution & Maintenance ------------- 11
5.3 How to operate GUI & Functions -------------------------------------- 12
R-tron., Inc.
2/15 page
RSP-APE-030M
User’s Manual
1. Overview
Figure 1.1 RSP-APE-030M Repeater
R-tron RSP-APE-030M Repeater can be used in CDMA service hole spots like in-buildings,
underground and tunnels to cover its service area. This repeater system designed for dual and
simultaneous service, namely, it receives signals from the base station through donor antenna,
amplifies the signals and re-transmits it to one or other mobile terminals. Also, it amplifies the signals
which comes from mobile terminals through distributor antenna and re-amplifies it to base station.
Using local OMT(Operation and Maintenance Terminal) which is connected between repeater
control board and personal or laptop computer, it is possible to check or to control repeater status.
R-tron., Inc.
3/15 page
RSP-APE-030M
User’s Manual
2. Specifications
2.1 System specifications
Parameter
Frequency Band
Specifications
Down Link
1930 ~ 1995 MHz
Up Link
1850 ~ 1915 MHz
Maximum
Down Link
Transmit Power
Up Link
5 or 10 or 15 MHz
Gain
70dB
Gain Adjustment Range
30dB in steps of 1dB
Emissions
±885 kHz
< -45 dBc
±1.98 MHz
< -50 dBc
± 2.25 MHz
< -13 dBm
Ripple
Freq. Selectivity
65MHz Bandwidth
+15 dBm
Operating Bandwidth
Spurious
Remark
Max. 7 channels
1 dB Step
RBW = 30 kHz
RBW = 1 MHz
< 3.5dB
-40dB
≤ 16.0MHz
Delay
<5㎲
VSWR
≤ 1.5
Waveform Quality Factor
> 0.912
Noise Figure
≤ 5.0dB
Within operating bandwidth
Table 2.1 Repeater Specification
Figure 2.1 A body of the RSP-APE-030M
R-tron., Inc.
4/15 page
RSP-APE-030M
User’s Manual
2.3 Donor Antenna Diagrams
Figure 2.2 Donor Antenna
2.4 Distributor Antenna Diagrams
Figure 2.3 Patch Antenna
Figure 2.4 Omni Antenna
R-tron., Inc.
6/15 page
RSP-APE-030M
User’s Manual
3. System Configuration
3.1 Block Diagram
Figure 3.1 shows the block diagram of a band Selective repeater.
This diagram is applicable to repeaters for CDMA systems.
3.1.1 Downlink signal path
DL signal path gives a wireless mobile terminal path after receiving signal from base station,
amplifying and noise filtering. Please refer to the following picture 3.1, RSP-APE-030M repeater block
diagram.
3.1.2 Uplink signal path
UL signal path gives a path after receiving signal from mobile terminal, amplifying and noise filtering.
Please refer to the following picture 3.1, RSP-APE-030M repeater block diagram.
R-tron., Inc.
7/15 page
RSP-APE-030M
User’s Manual
4. Installation
4.1 Installation Overview
The following gives you guide how you can install R-tron repeater properly, considering field
situation and installation specific conditions.
4.2 Safety
4.2.1 Purpose
The following information gives you how you can proceed your job correctly and eliminate
dangerous condition.
4.2.2 Application Range
Installation supervisor should check and do the proper thing to check preliminary dangerous
condition.
4.3 Installation information-1
4.3.1 Right-of-way
- The repeater shall be installed in the location owned or leased by the carrier.
- If the repeater is installed in the building, an appropriate space for the installation must be
considered.
4.3.2 Conditions for the Installation space
Repeater should be installed as followings :
In the building
- Avoid certain part which is located something heavy or water tank on the roof, considering
weight balance.
- Select certain place which is good for air ventilation.
- There will be enough space to check the repeater.
R-tron., Inc.
8/15 page
RSP-APE-030M
User’s Manual
4.4 Installation Information-2
The installation of the repeater depends on the types of support, location, and the demand of
the carrier.
Figure 4.1 Antenna & Repeater Installation
4.4.1 General Condition
- Check whether the repeater status is correctly horizontal angle.
- Check whether there is enough space for maintenance and repair.
4.4.2 Installing Band set
- Repeater main box should be installed 8.2 inches at least, above from the ground.
- When you install the repeater main box, do not impact on its installation to other repeaters
maintenance.
- Safety plate should be installed 8.2 inches at least, above from the ground.
4.4.3 Precautions
- Never mount the donor or coverage antenna near a window, where Signal can easily pass through the
glass
- Mount the donor antenna as high as physically possible to the exterior of the building, maximizing
the vertical separation between antennas and pointing away from the building, toward the base station
site.
- Install the antennas taking advantage of any existing building structure Such as brick walls, metal
roofs, or multiple wall structures to additionally attenuate the path between them.
- When using directional antennas inside the building to cover Corridors and hallways, point the
interior antenna away from The donor antenna location .
- In extreme cases, the building configuration may not allow for Such separation and isolation. If
additional isolation is required, Coaxial attenuation may be inserted between the donor antenna and the
repeater , with the potential compromise to the coverage within the building
R-tron., Inc.
9/15 page
RSP-APE-030M
User’s Manual
5. Graphic User Interface (for maintenance)
5.1. GUI Overview
The following picture is RSP-APE-030M GUI Configuration.
Figure 5.1 Main window
When you first execute main window, you can see the above picture and it show you repeater status.
R-tron., Inc.
10/15 page
RSP-APE-030M
User’s Manual
5.2 Preliminary Steps for GUI Execution & Maintenance
5.2.1 Preliminary Steps before using GUI
a. Check all connection status during the installation.
b. Set the baud rate which you are going to use.
c. Connect the repeater main power cable.
d. Connect RSP-APE-030M “LOCAL OMT” with PC, using RS232 cable.
Figure 5.2 Connection RSP-APE-030M with PC
5.2.2 Executing
USB Driver & GUI program
a. Excuting “PreInstaller” and check the USB driver is normal and the port number.
Figure 5.3 USB Driver files
b. Excuting “MINI30_USPCS”
Figure 5.4 GUI files
5.2.3 GUI Communication
When the communication between Personal Computer and Repeater MCU board is OK, Tx/Rx yellow
LED which is up-left corner in the GUI screen will be flashed.
Figure 5.5 Communication Verification LED
R-tron., Inc.
11/15 page
RSP-APE-030M
User’s Manual
5.3 How to operate GUI & Functions
Repeater can be controlled in Set-up mode. In Set-up pop-up window, you can input the value and
control DL/UL HPA, AGC, Shutdown and attenuation.
When you are going to check repeater status, click “Synchronize” button which is in the bottom side in
the screen. After setting output value, you can set AGC/ASD level value, using AGC/ASD button.
Figure 5.6 Setup mode
R-tron., Inc.
12/15 page
RSP-APE-030M
User’s Manual
5.3.1 Description for icon indication
Figure 5.7 Main icons
▶
Polling : Communication possible
▶
Stop : Stop Communication
▶
File : Load the file of downloading
▶
Exit : Exit
5.3.2 How to set repeater gain
System gain value can be changed using Down/Up link attenuation value control which is in “ATTN”
pop-up window. Available set attenuation value is from 0 to 30 dB, Down/Up Link both.
You can check current system gain in status mode.
Figure 5.8 Gain Setting
R-tron., Inc.
13/15 page
RSP-APE-030M
User’s Manual
5.3.3 Circumstance Condition Control
This function enables you to set the internal temperature of the system and the upper values of the
input/output level. To change the values, you can enter the desired settings and click the “APPLY”
button at the upper part of the control window.
In the left side, you can see current settings for the internal temperature of the system.
Figure 5.9 Control Window of Environmental Conditions
5.3.4 Controlling power amplifier
On the “ON/OFF” window, you can control power amplifiers for each path.
In the left side window, you can see the current path status (ON/OFF) of the system.
Figure 5.10 Control Window of Power Amplifier and Battery
5.3.5 Controlling input/output
You can set the upper/lower values of the current input/output RF power of the up-/down-links. To
change the values, you can enter the desired settings and click the “SET” button at the upper part of
the control window.
In the status mode, you can see the current input/output settings of the up-/down-links.
Figure 5.11 Controlling Input/output
5.3.6 AGC(Auto Gain Control) & ASD(Auto Shutdown) Setting
This function lets you control AGC settings and the ON/OFF status. To change a setting, you need to
enter a value and click the SET button at the lower part of the Control Window.
R-tron., Inc.
14/15 page
RSP-APE-030M
User’s Manual
Figure 5.12 AGC/ASD Setting window
R-tron., Inc.
15/15 page

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 15
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:a06d180a-cb05-4829-bca9-3b112674147b
Producer                        : Acrobat Distiller 6.0 (Windows)
Modify Date                     : 2006:05:23 20:26:18+09:00
Create Date                     : 2006:05:11 15:17:08+09:00
Metadata Date                   : 2006:05:23 20:26:18+09:00
Document ID                     : uuid:c4e70b70-b6fb-4a9d-9334-2cd3a93df975
Format                          : application/pdf
Title                           : untitled

EXIF Metadata provided by EXIF.tools