RCI 3525 Electromechanical Rack Handle Lock Installation Instructions Is3525 R1115
User Manual: RCI 3525 Electromechanical Rack Handle Lock Installation Instructions Installation Instructions
Open the PDF directly: View PDF 
.
Page Count: 3
| Download | |
| Open PDF In Browser | View PDF |
3525 INSTALLATION 3525 Electronic Locking Rack Handle Package Contents • 3525 Electronic Locking Rack Handle • 78.7” (2000 mm) Wire Harness • M3x25mm Long Mounting Screws (qty 4) • M3x14mm Long Mounting Screw • Rotation Limiter • CAM Bolt • Top Mounting Bracket • Bottom Mounting Bracket • IS3525 Installation Instructions • Keys (qty 3) Tri-Color LED Indicator Handle Key Cylinder Specifications Voltage: 12VDC to 24VDC (NOTE: Status LED will blink red if the supply voltage is out of range.) Standby Current: 50mA maximum at 12VDC Operating Current: 200mA maximum at 12VDC (with no external mechanical load applied to handle) Operating Transit Time: 1 second maximum (NOTE: Power must be present during transit times. If power is removed while the lock slide is moving to the unlock position, then the control input signal must be asserted again. If power is removed while the lock slide is moving to the lock position, it will complete it’s cycle when power is restored.) Electronic Unlock Time: 3 seconds minimum Alarm Outputs: 100mA/output maximum Overall Dimensions: 6.71” H x 1.45” W x 1.98” D (170.6 x 37 x 50.25mm) IS3525 © 2015 RUTHERFORD CONTROLS INT’L | A DORMA GROUP COMPANY WWW.RUTHERFORDCONTROLS.COM • PHONE: 1.800.265.6630 • FAX: 1.800.482.9795 • E-MAIL: SALES@RUTHERFORDCONTROLS.COM PCN15063 R11/15GR E R OR ALARM OR ALARM 3525 Installation Instructions (Continued) Handle Mounting Fig. 1 1” * 25mm Rotation Limiter CAM 5.9” * Top Mounting Bracket CAM Bolt 150mm 1. Assemble handle according to the proper handing required. 2. Rotation Limiter and Bottom Mounting bracket determine handing. 3. If existing cam or rod mechanism are installed on original handle remove and install on new handle. 4. Ensure the proper cutout in the door. (See Fig. 1) 5. Install handle though cutout and install top & bottom mounting brackets. 6. Install wiring harness and route to hinge side of door securing in place to ensure that nothing will bind or catch. 7. Proceed to wiring. (See Fig. 2) M3x14mm Screw (1 place) M3x25mm Screw NOTE: (4 places) Bottom Mounting Bracket * 1) Cut-out dimensions. 2) Handing is determined by rotation VIEWED FROM BACKVIEWED FROM BACK VIEWED FROM BACKVIEWED FROM BACK HANDLE ROTATION HANDLE IS COUNTER ROTATION CLOCKWISE IS COUNTER CLOCKWISEHANDLE ROTATION HANDLE limiter and bottom mounting bracket. IS CLOCKWISE ROTATION IS CLOCKWISE FROM FRONT FROM FRONT FROM FRONT FROM FRONT Rotation Limiter Viewed from back. Handle rotation is counter clockwise from front. Rotation Limiter Viewed from back. Handle rotation is clockwise from front. VIEWED FROM BACK VIEWED FROM BACK VIEWED FROM BACK VIEWED FROM BACK HANDLE ROTATION IS COUNTER HANDLE CLOCKWISE ROTATION IS COUNTER CLOCKWISE HANDLE ROTATION IS CLOCKWISE HANDLE ROTATION IS CLOCKWISE FROM FRONT FROM FRONT FROM FRONT FROM FRONT Bottom Mounting Bracket Viewed from back. Key rotation is counter clockwise from front. Bottom Mounting Bracket Viewed from back. Key rotation is clockwise from front. © 2015 RUTHERFORD CONTROLS INT’L | A DORMA GROUP COMPANY WWW.RUTHERFORDCONTROLS.COM • PHONE: 1.800.265.6630 • FAX: 1.800.482.9795 • E-MAIL: SALES@RUTHERFORDCONTROLS.COM VIEWED FROM BACKVIEWED FROM BACK KEY ROTATION IS COUNTER KEY ROTATION CLOCKWISE IS COUNTER CLOCKWISE VIEWED FROM BACKVIEWED FROM BACK KEY ROTATION IS CLOCKWISE KEY ROTATION IS CLOCKWISE 2 - 3525 Installation Instructions (Continued) + Wiring RED: Postive RED - 12/24 VDC POSITIVE BLACK - 12/24 VDC NEGATIVE BLACK: Negative WHITE - ACTIVATION TRIGGER 1. Red & Black are 12 to 24 VDC input voltage. 2. Orange is a positive input with a Normally Open Switch. The lock will unlock for a minimum of 3 seconds on a momentary activation (50 millisecond min.) or remain unlocked as long as the circuit is closed. 3. Yellow is an alarm that will activate when the key is used to unlock the cabinet or anytime the handle is not seated and locked. 4. Brown is an alarm that will activate when the lock is electrically activated and will remain on until the lock electrically relocks. ORANGE: Activation Trigger YELLOW - 200 mA OUTPUT FOR ALARM BROWN - 200 mA OUTPUT FOR ALARM YELLOW: 100mA Output for Alarm BROWN: 100mA Output for Alarm Fig. 2 VIEWED FROM BACK HANDLE ROTATION IS COUN FROM FRONT 12~24 VDC POWER SUPPLY - BLACK + RED ORANGE YELLOW 100mA MAX BROWN 100mA MAX Fig. 2a Lock Status Latch LED Alarm Wires Secure Steady Blue Inactive Electrically Released Blue/ Magenta Flashing Brown Active Mechanically Released Blue Flashing Yellow Active Handle Not Fully Closed Blue/Red Flashing Yellow/Brown Active NOTE: The lock sensor is an optical device that senses the presence of the locking cam. Reflectivity of the locking cam material can affect sensing. Keyed cylinder can affect sensing. Removal of the factory installed keyed cylinder will VIEWED FROM BACK void warranty. KEY ROTATION IS COUNTER CLOCK FROM FRONT © 2015 RUTHERFORD CONTROLS INT’L | A DORMA GROUP COMPANY WWW.RUTHERFORDCONTROLS.COM • PHONE: 1.800.265.6630 • FAX: 1.800.482.9795 • E-MAIL: SALES@RUTHERFORDCONTROLS.COM 3
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes XMP Toolkit : Adobe XMP Core 5.3-c011 66.145661, 2012/02/06-14:56:27 Create Date : 2015:11:24 16:08:49-05:00 Metadata Date : 2015:11:24 16:08:51-05:00 Modify Date : 2015:11:24 16:08:51-05:00 Creator Tool : Adobe InDesign CS6 (Macintosh) Instance ID : uuid:d18c1b84-6e94-664d-a200-3b65b0e41b74 Original Document ID : xmp.did:0180117407206811A46CF74D571AED6E Document ID : xmp.id:5C3590D807206811822AE4544B50C0E8 Rendition Class : proof:pdf Derived From Instance ID : xmp.iid:5B3590D807206811822AE4544B50C0E8 Derived From Document ID : xmp.did:5A3590D807206811822AE4544B50C0E8 Derived From Original Document ID: xmp.did:0180117407206811A46CF74D571AED6E Derived From Rendition Class : default History Action : converted History Parameters : from application/x-indesign to application/pdf History Software Agent : Adobe InDesign CS6 (Macintosh) History Changed : / History When : 2015:11:24 16:08:49-05:00 Format : application/pdf Producer : Adobe PDF Library 10.0.1 Trapped : False Page Count : 3 Creator : Adobe InDesign CS6 (Macintosh)EXIF Metadata provided by EXIF.tools