REYAX TECHNOLOGY RR10 RFID Reader Module User Manual

REYAX TECHNOLOGY CO.,LTD. RFID Reader Module

user manual

REYAX RR10
RFID HF Reader Module
User’s Guide
1.OperationalDescription
TheRR10RFIDsolutioniscompliantwithNFCforumstandardforReadermode
whichsupportsISO15693andISO14443A/Bprotocols.It’sveryeasytoconnectto
anyhostwithUARTinterfaceasPC,PDAandmobilephone.
2.1HardwareInstall
PleaseinsertthecabletotheRR10.
TheothersideinserttotheUSBinterface.
2.
2
Bel
o
Ple
a
■
■
pat
h
the
■I
f
lau
n
2
Softwa
r
o
wsection
s
a
sefollow
b
UnplugRFI
Double‐Cli
c
h
.Andfoll
o
installatio
n
f
youeveri
n
n
chedfirst.
r
einstall
s
introduce
s
b
elowsteps
DHFdevic
e
c
k“RFID_N
F
o
wthestep
s
.
n
stalledRFI
s
thesteps
t
toinstalld
e
e
fromUSB
F
C_Install.e
x
s
tocomple
DHFDem
o
t
osetupde
emoapplic
a
port.
xe”under
“
te
o
Applicatio
moapplica
t
a
tion.
“
.\Demonst
r
n
,theunin
s
t
ionsandd
r
r
ation\Win
d
s
tallproces
s
rivers.
d
ows\BCB”
s
willbe
No
w
w
,theinsta
l
l
lationproc
e
ssislaunched.
▓L
a
the
and
3.
O
3.
1
■
mo
d
bel
o
aunchdem
mainscre
e
d
RR10.The
O
perati
o
1
ReadT
a
Launchrea
d
edemofo
o
w.TheRFI
oapplicati
o
e
n,the“Sta
t
defaultint
e
o
n
a
gs
dermode
d
rmwillbe
s
Dprotocol
c
o
nbydoubl
t
us”areain
e
rfaceisRS
‐
d
emoform
s
hownas
c
anbesele
eclick“RFI
formsyou
t
‐
232(UART
)
byclicking
“
ctedfrom
“
DNFCDe
m
t
hephysica
l
)
.
“
Mode”‐>”
R
“
Protocol”
a
o”shortcu
t
l
linkstatus
R
eader”.T
h
a
rea.
t
ondeskto
between
P
h
entherea
d
p
.In
P
C
d
er
Ch
o
tag
s
o
ose“Inven
t
s
continuo
u
t
ory”page
u
sly
a
ndputta
g
g
snearRR1
0
0
D1Click“
S
S
tart”butt
o
o
ntofindin
g
g
Cli
c
c
k “Stop”
b
utton t
o
o
stop.
Cli
c
c
k “Clear
”
”
b
utton to clear tag
i
i
nformatio
n
n
.
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifications not expressly approved by the party responsible for compliance could void
the user's authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
LABEL OF THE END PRODUCT:
The final end product must be labeled in a visible area with the following " Contains TX FCC ID:
QLY-RR10 ". If the size of the end product is larger than 8x10cm, then the following FCC part 15.19
statement has to also be available on the label: This device complies with Part 15 of FCC rules.
Operation is subject to the following two conditions: (1) this device may not cause harmful interference
and (2) this device must accept any interference received, including interference that may cause
undesired operation.

Navigation menu