RFI Technology RFI-001 Wireless System for POS and Kitchen Printer User Manual FCC 2
RFI Technology Company Limited. Wireless System for POS and Kitchen Printer FCC 2
User Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 388964 |
| Application ID | l4rS4p7XQ/nm3ku13pXCsQ== |
| Document Description | User Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 11.42kB (142739 bits) |
| Date Submitted | 2004-01-15 00:00:00 |
| Date Available | 2004-01-09 00:00:00 |
| Creation Date | 2003-12-06 12:27:01 |
| Producing Software | Acrobat Distiller 5.0 (Windows) |
| Document Lastmod | 2003-12-06 12:27:01 |
| Document Title | Microsoft Word - User Manual FCC_2.doc |
| Document Creator | PScript5.dll Version 5.2 |
| Document Author: | Kenny Kam |
SPRINTER Wireless System User Manual PWR/RT KP1 KP4 KP3 KP 2 PW R/R KP1 KP2 KP3 KP4 1. General Description ECR/POS MODULE (POS Module) - It is connected to the ECR or POS. - 4 × RJ45 sockets for connections to ECR or POS Serial Ports by RJ45/DB9 cable. - 1 × DC jack for power input - 1 × Red LED for Power and RF Status. - 4 × Green LEDs to indicate Data Port Status. - 1 × Push Switch to enter Register Mode. DC 5V KP1 KP2 KP3 KP4 POS Module LEARN 2. Placement Orientation SPRINTER can be placed on any flat surface or mounted on the wall. In either case, the antenna must be set upward for better reception of signal. PWR/RT KP1 KP 4 KP3 KP2 PW R/R 3. KP1 KP2 KP3 KP4 Checklist for unpacking Before start to install the SPRINTER system, please check the items listed below: POS Module Pack: 1 × POS Module - 1 × Cable with RJ45/DB9 Connector - 1 × AC/DC adaptor If any thing missed, contact your dealer for supplement. 4. Installation Step 1 – Setup the Serial Port on your ECR/POS and Printer The Serial port of the ECR/POS and Printer must be set as below: - Baud Rate: 9600 bps - Date length: 8 Bit - Parity: None - Stop Bit: 1 or more - Handshaking: Hardware control (DTR/DSR) Step 2 - Connecting the Modules POS Module It is simply connecting the POS module to ECR or POS serial port by the RJ45/DB9 cable. If you have more than one Kitchen Printer, you just need to purchase additional RJ45/DB9 cables from your dealer for connecting the modules to ECR or POS. The Port Number on the POS Module corresponds to the ID of the Kitchen Printer: KP 1 Æ Kitchen Printer ID 1, KP 2 Æ Kitchen Printer ID 2, KP 3 Æ Kitchen Printer ID 3, KP 1 KP 2 KP 3 KP 4 KP 4 Æ Kitchen Printer ID 4, Step 3 – Connecting the Power Before power up the SPRINTER system, all ECR, POS or Kitchen Printers should be switched on in advance. Plug the AC/DC adapter to the wall outlet. Then, connect the adapter DC plug to the module’s DC input jack. A self-test will be run automatically. The Power LED (Red) and the Data LED (Green) will flash once. If no error found, the Power LED will be stay on and other LEDs will be off. The system is ready to go! If error is found, all LEDs will be flashing and long beep sound will be heard. Unplug the power and plug in again. If still has error, contact your dealer. If both the LED and buzzer back to normal indications, continue the Register process in Step 6. 5. LED & Buzzer Indications Status Power/RF Data LED Buzzer Remark LED POS Ready Mode Steady ON OFF Silence Transferring Steady ON Flashing Silence Module No data in processing. Data Printer error Randomly Stead ON Stead ON Printing in progress. Beep twice Paper out, Printer after time out. buffer full, or Printer not ready. RF Error Flash for Stead ON Beep twice. 5 seconds POS ID error Flashing RF error during transmission. Flashing Continuous Reset the power Beep sounds and redo the Register procedure again. If error still exists, contact your dealer. 6. Cable connections To ECR/POS Serial Port DB 9 (Female) Pin Description I/O Data Terminal Ready (DTR) Clear to Send (CTS) Data Set Ready (DSR) To SPRINTER POS Unit DB9F Pin # RJ45 Pin # I/O RJ45 Pin Description Data Set Ready (DSR) Request to Send (RTS) Data Terminal Ready (DTR) Signal GND Signal GND TxData RxData Request to Send (RTS) Rx Data Tx Data No Connection No Connection *All the information on this manual is subjected to change without prior notice. Caution Modifications not authorized by the manufacturer may void users authority to operate this device. NOTE: This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try and to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help. *All the information on this manual is subject to change without prior notice.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.3 Linearized : No Create Date : 2003:12:06 12:27:01+08:00 Modify Date : 2003:12:06 12:27:01+08:00 Page Count : 7 Creation Date : 2003:12:06 04:27:01Z Mod Date : 2003:12:06 04:27:01Z Producer : Acrobat Distiller 5.0 (Windows) Author : Kenny Kam Metadata Date : 2003:12:06 04:27:01Z Creator : Kenny Kam Title : Microsoft Word - User Manual FCC_2.docEXIF Metadata provided by EXIF.tools