RFID SF-BTHFRD RFID Reader with BLE User Manual

Hong Kong RFID Ltd. RFID Reader with BLE Users Manual

Users Manual

SF-BTHFRD User Manual P. 1SF-BTHFRD USER MANUALGENERAL DESCRIPTIONSF-BTHFRD is a high performance and portable Multi-Protocol HF tag reader supporting ISO15693, ISO14443TypeA/TypeB. It isdesigned supports fast tag read/write operation with high identification rate. It can be widely applied in many RFID applicationsystems such as stock management, traceability system, personnel identification, access control and anti-counterfeit system.FEATURESFashion, thin and well portable design;Support Bluetooth 4.0 wireless communication;Ultra-low power design;Support interactive and trigger-activating work mode;Support mainstream ISO15693, ISO14443TypeA/ Type B protocol tag;Advanced anti-collision algorithm;Built-in TX/RX antenna with up to 100mm effective distance*;3 groups LED as working indicator;CHARACTERISTICSAbsolute Maximum RatingITEM SYMBOL VALUE UNITInput Voltage VCC 6 VOperating Temp. TOPR -10~+70 Storage Temp. TSTR -20~+85 Electrical Specification**Effective distance depends on antenna, tag and working environment.ITEM SYMBOL MIN TYP MAX UNITInput VoltageVCC4.2 5 5.5VInput Current IBAT 500 mAStandby Current ISTBY 2 3 mAContinuous RFCurrent IRF 80 100 mAFrequency FREQ 13.56 MHzEffective Distance*DIS 0 80 100 mmSize L×W×H 110 × 50 × 5.8 mm
SF-BTHFRD User Manual P. 2INTERFACE1. SocketItem DescriptionTrigger Button Single activate the reader to read 15693 or 14443A tag’s UID and send to hostPower Switch Set left for power on and right for power offItem DescriptionMicro USBPower Supply2. Panel IndicatorItem DescriptionLED1 Red on during trigger-activating. Green flash when successfully reading a tag.LED2 Red flash slowly shows the reader is power on.LED3Power SwitchTrigger ButtonLED1LED3LED2Micro USB
SF-BTHFRD User Manual P. 3Disposal:For indoor use only. The apparatus shall not be exposed to dripping or splashing.No user replaceable parts inside, refer servicing to manufacturer specified agency or qualified servicepersonnel.Only use a accessories/battery specified by the manufacturer.Do not expose to excessive heat sources, sunshine, fire or the likeAll electrical and electronic products including batteries should be disposed of separately from themunicipal waste stream via designated collection facilities appointed by the government or the localauthorities.FCC Notice:FCC ID: XNO-SF-BTHFRDModel: SF-BTHFRDThis device complies with Part 15 of the FCC Rules.Operation is subject to the following two conditions: (1) This device may not cause harmfulinterference, and (2) This device must accept any interference received, including interference thatmay cause undesired operation.The grantee is not responsible for any changes or modifications not expressly approved by the partyresponsible for compliance. Such modifications could void the user’s authority to operate theequipment.The RF Exposure Compliance distance is 20mm.NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protectionagainst harmful interference in a residential installation. This equipment generates, uses and canradiate radio frequency energy and, if not installed and used in accordance with the instructions, maycause harmful interference to radio communications. However, there is no guarantee that interferencewill not occur in a particular installation. If this equipment does cause harmful interference to radio ortelevision reception, which can be determined by turning the equipment off and on, the user isencouraged to try to correct the interference by one or more of the following measures:—Reorient or relocate the receiving antenna.—Increase the separation between the equipment and receiver.—Connect the equipment into an outlet on a circuit different from that to which the receiver isconnected.—Consult the dealer or an experienced radio/TV technician for help.-END DOCUMENT-

Navigation menu