RM COSTRUZIONI ELETTRONICHE Srl KL7505V HF power amplifier User Manual KL7505 Istruction Rev 1 1

Download:
Mirror Download [FCC.gov]
Document ID	2412938
Application ID	ikjxzubbf4sqwk7Oh9nMZA==
Document Description	General Specifications
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	263.06kB (3288204 bits)
Date Submitted	2014-10-08 00:00:00
Date Available	2014-10-08 00:00:00
Creation Date	2014-07-31 15:17:58
Producing Software	GPL Ghostscript 9.10
Document Lastmod	2014-07-31 15:17:58
Document Title	KL7505_Istruction Rev.1.1
Document Creator	PDFCreator Version 1.7.3
Document Author:	Utente

GENERAL SPECIFICATIONS
POWER SUPPLY
Working voltage from 11V to 14V
Maximum current consumtion 30A
30A Safety Fuse
RF PERFORMANCE
Frequency range 28-30MHz
10 METERS BAND
Maximum Gain 15db
Maximum Pover IN 10W (Higher powers may permanently damage the device)
Maximum Pover OUT 240W
KL7505
USER MANUAL
www.rmitaly.com info@rmitaly.com
FRONT PANEL
INSTALLATION NOTE
CONNECTION DIAGRAM
This device must be installed in an area where there is adequate ventilation for the heat
sink.
The amplifier is not designed for continuous transmission and should not be operated in
this manner. Failure to observe this will cause the amplifier to shut down from excessive
temperature.
If the amplifier is operated in high ambient temperatures transmission times should be kept
short to avoid excessive heat sink temperature. Excessive heat sink temperature will cause
the amplifier to shut down transmission. This is indicated when the TX LED flashes.
If this occurs operation of the amplifier should be stopped and the amplifier will regain
normal operation when the temperature falls to an acceptable level. This may take more
than 5 minutes.
ANTENNA 50Ω
FREQUENCY RANGE EQUAL
TO OR GREATER OF 28-30MHz
10 METERS BAND
MAXIMUM POWER SUPPORTED BY ANTENNA NOT LESS
THAN 240W
[ Power On Led
\ Transmission state indication LED, if blinking indicates a
overtemperature. To restore turn off and turn on, again, the device.
] Power On switch
^ Modulation type selection (delay return to receive mode)
- AM/FM 0
Seconds Delay
- F-SSM
0.8 Seconds Delay
- S.SSB
1.2 Seconds Delay
_ Gain selection
- HI
14db ±1
- MID
12db ±1
- LOW
8db ±1
BACK PANEL
ANT
PAY ATTENTION TO THE
POWER POLARITY
RX\TX
RADIO
12V
[ TX/TX 50Ω Connector to be connected to your radio transceive
MAXIMUM POWER-IN 10W
\ ANT 50Ω Connector to be connected to a proper antenna for the
frequency in use
] 13.5V Supply. Lower or unstable voltages compromise device
performance

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Page Count                      : 2
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:a04ef31e-1b10-11e4-0000-a6ddc7ff56fa
Producer                        : GPL Ghostscript 9.10
Keywords                        : ()
Modify Date                     : 2014:07:31 15:17:58+02:00
Create Date                     : 2014:07:31 15:17:58+02:00
Creator Tool                    : PDFCreator Version 1.7.3
Document ID                     : uuid:a04ef31e-1b10-11e4-0000-a6ddc7ff56fa
Format                          : application/pdf
Title                           : KL7505_Istruction Rev.1.1
Creator                         : Utente
Description                     : ()
Author                          : Utente
Subject                         : 

EXIF Metadata provided by EXIF.tools