ROBOTIS BT-410-DONGLE BT-410 DONGLE User Manual Users manual

Download:
Mirror Download [FCC.gov]
Document ID	3604698
Application ID	ASpW4Wx8ltWgzaU8r/JzWA==
Document Description	Users manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	13.4kB (167555 bits)
Date Submitted	2017-10-13 00:00:00
Date Available	2018-04-11 00:00:00
Creation Date	2017-10-13 15:16:02
Producing Software	Microsoft® Word 2010
Document Lastmod	2017-10-13 15:16:02
Document Title	Users manual
Document Creator	Microsoft® Word 2010
Document Author:	Jason Jin

BT-410 Dongle (MASTER)
Device Image
[ Photo : BT-410 Dongle ]
Device Description
[BT-410 Dongle] has USB 2.0 interface and Bluetooth 4.0 Low Energy Standard communication interface
(MASTER). This device converts these two communication interfaces.
Therefore, you can plug [BT-410 Dongle] to [PC] and pair it to a [BT-410 SLAVE Module], then your
[PC] and [BT-410 SLAVE Module] can exchange data.

Wireless Communication modules CAN pair with BT-410 Dongle:

BT-410 SLAVE Module
Wireless Communication modules CAN pair with BT-410 Dongle:
BT-410 MASTER Module
BT-210 MASTER Module
BT-210 SLAVE Module
BT-100/110A
o
ZIG-100/110A
Example of application
Missions can achieved by BT-410 Dongle and BT-410 SLAVE Module
FW recovery FW update
Manager 2.0 Manager 2.0
Entry Scratch
Task 2.0
Motion 2.0
download
download
CM-150
CM-200
OpenCM7.0
CM-530
CarBot
Communication Modes
BT-410 Dongle can achieve reliable 1:1 communication.
[1:1 Communication]

Plug it to a powered usb port of PC, then the blue LED starts to blink. After paired to BT-410
SLAVE Module, the blue LED stays ON.

Auto-Pairing: When the blue LED of BT-410 Dongle blinks, put a BT-410 SLAVE Module close to
Dongle(less than 10cm), then these two devices will pair automatically. After this operation, those
two can find and communicate with each other through further distance.
H/W Specification

Weight : 7.5g

Dimensions : 50.5mm x 20.0mm x 10.5mm

Bluetooth specification : Bluetooth Specification 4.0 Low Energy Support

Communication range : 10m

Spectrum band : 2.4 GHz ISM Band

Bandwidth : MAX 128kbps

Default baudrate : 57600bps

Voltage range : 4.5V ~ 5.5V

Current consumption : 25mA (Max)

Temperature range : -0℃ ~ 40℃

Baudrate range : 1,200bps – 1,000,000bps

Antenna type : Chip Antenna

USB Interface : USB 2.0 Full Speed

Sensitivity : -81dBm (Typical)

Tx power : -6~4dBm(Class 2)
FCC Information
This device complies with part 15 of the FCC Results. Operation is subject to the
following two conditions :
(1) This Device may not cause harmful interface, and
(2) This device must accept any interference received, including interference that
may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for CLASS B digital
device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try
correct the interference by one or more of the following measures:
1.1. Reorient or relocate the receiving antenna.
1.2. Increase the separation between the equipment and receiver.
1.3. Connect the equipment into an outlet on a circuit different from that to which receiver is
connected.
1.4. Consult the dealer or experienced radio/TV technician for help.
WARNING
Changes or modifications not expressly approved by the manufacturer could void the
user’s authority to operate the equipment.
“CAUTION : Exposure to Radio Frequency Radiation.
Antenna shall be mounted in such a manner to minimize the potential for human
contact during normal operation. The antenna should not be contacted during operation
to avoid the possibility of exceeding the FCC radio frequency exposure limit.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 4
Language                        : ko-KR
Tagged PDF                      : Yes
Author                          : Jason Jin
Creator                         : Microsoft® Word 2010
Create Date                     : 2017:10:13 15:16:02+09:00
Modify Date                     : 2017:10:13 15:16:02+09:00
Producer                        : Microsoft® Word 2010

EXIF Metadata provided by EXIF.tools