RSI VIDEOTECHNOLOGIES SV50 Outdoor Streaming Motion Viewer User Manual Manual OSMVC601

RSI VIDEOTECHNOLOGIES Outdoor Streaming Motion Viewer Manual OSMVC601

Contents

Manual_OSMVC601

The OSMVC 200/601/702 MotionViewer is a wireless, battery operated, motion activated outdoor camera designed for use in Videofied®security systems.• Powered by 4 Lithium batteries for extended battery life. • Lens for vertical curtain detection.• 4 infrared LEDs for 12m night vision.• Fully weatherproof (IP54) and temperature resistant (-25°C/+70°C).• Tilt sensor tamper.• Transmits check-in/status signal every 8 minutes.• Video capture and transmission in «streaming mode» on user request.Product SummaryInstallation GuidelinesFor easier installation, programming and RF testing should be done to check for good communication between the control panel and all system devices before mounting system devices. Install the detector and other system devices in the order of the following steps:> Programming/RF Testing - program detector and all other devices into the control panel and test RF communication from each intended device location to the control panel.> Mounting - mount detector at the tested location.Mounting> Use proper tools and hardware. > Mount camera between 2.5 m to 3,5 m height. > The OSMVC MotionViewer detection distance may vary depending the detector mounting (height, tilt). The OSMVC is not suitable to protect an area, it needs to be used to protect the perimeter of an installation. > Mount detector aimed to protect the perimeter.> In order to reduce false alarms, do not aim the detector toward vegetation, a road, or unlimited space.> Do not cover the Fresnel lens.MB110 Mounting kit for Outdoor MotionViewerDOC. - REF. 213-OSMVCVERSION : AUGUST 20161INSTALL SHEET OSMVC OUTDOOR STREAMING MOTION VIEWER
Programming/RF Testing/MountingThe following provides summarized steps for device programming, testing, and mounting. For complete details, refer to the control panel installation manual.1 Separate the base from the box2 Install 4 3.6V LS14500 SAFT batteries observing correct polarity. 3 Put control panel into Programming/Configuration mode.4 Using a programmed alphanumeric keypad, proceed through menus until the display shows ADD A NEW DEVICE.5 Press OK/YES. the display shows PRESS PROGRAM BUTTON OF DEVICE.6 Press and release program button on the OMV MotionViewer.The OMV PIR flashes.7 Wait for keypad display to show CAMERA(1 - 25) PROGRAMMED. Press OK/YES, the display shows RADIO RANGE TEST? Press OK/YES again. The camera LED starts flashing and keypad display shows RF TEST.8 Take the OSMVC camera to its intended mounting location and make sure LED flashes continuously or you receive a 9/9 indicating good communication with the control panel.9 Press OK/YES to end radio range test then press ESC/NO.10 The keypad displays : AREA ALLOCATION : AREA : 1Press either arrow button repeatedly until desired area number appear then press OK/YES. By default all devices in Area 1 are automatically delayed. 11 The display shows NAME + LOCATION: Enter appropriate device name/location (up to 16 characters), then press OK/YES. The display shows the device number and name for your verification. 12 Mount the OSMVC on the MB 110 or the MBW110 Mounting kit. Follow the installation guidelines shown in this document.13 Press OK/YES. The display shows FUNCTIONAL DEVICE TEST? Press OK/YES and verify camera operation. The activation of the LED will determine the detection field.14 Press OK/YES to end detection verification.15 The display shows OPERATION COMPLETED or ADD A NEW DEVICE? Press YES/OK. Repeat steps 1 – 14 for remaining cameras.16 When finished, exit from configuration mode.ScrewProgram button2INSTALL SHEET OSMVC OUTDOOR STREAMING MOTION VIEWER
3INSTALL SHEET OSMVC OUTDOOR STREAMING MOTION VIEWERMounting RecommendationsPlease direct the OSMVC along a fence or a wall in order to protect an access point. The detector should not be mounted close or above an access point. Such installation increase the probability of a missed intrusion.For optimal use, the OSMVC MotionViewer mounting shall respect the following recommendations:Mounting height : RSI Video Technologies recommends a 2,5 m to 3,5 m mounting height. When you install the MotionViewer higher, the detection distance is raised. However the sensitivity is reduced and the blind area under the MotionViewer is larger. When you install the MotionViewer lower, the sensitivity is raised and the blind area under the detector is reduced. However the detection distance will be reduced.Tilt :Raising or reducing the tilt, even slightly, has a big impact on the detection distance and on the blind area under the MotionViewer. We recommend to slightly tilt the OSMVC to reduce its detection range and avoid false alarms.To precisely determine the tilt angle use a smartphone app like Smart Protector (Android) or Pitch Gauge (iOs).Blind angleMax detection distanceTiltMounting heightMax detection distance : OSMVCTilt angle5° 10° 15° 20° 30°Mounting height2.5 m 14 m* 11 m 8 m 6,5 m2.75 m 14 m* 12 m 9 m 7 m 5 m3 m 14 m* 13 m 9,5 m 7, 5 m 5,5 m3.25 m 14 m 10 m 8 m 5,5 m3.5 m 14 m* 11 m 8,5 m 6 mTheoretical values estimated for default sensitivity.These values only represent the physical limits of the OSMVC detection and not its maximum detection range. Long range sensitivity is reduced and depends on infrared detection properties (see page 5).* In some cases, false alarms can be triggered from outside the 14m detection limit (street, bushes, trees, etc). If that happens, please slightly tilt the OSMVC downward to prevent false alarms.
4INSTALL SHEET OSMVC OUTDOOR STREAMING MOTION VIEWERPerimeter protectionTilt TamperThe OSMVC MotionViewer can detect manipulation thanks to its built-in electronic accelerometer.This device can detect shocks, movements, wall or cover tamper but also changes in its orientation.When a movement of the OSMVC is detected, the LED lights up for 3 seconds.When it is armed for the first time, the OSMVC registers its position in space. If its orientation is significantly changed on its transverse or longitudinal axis, a tamper alarm is sent to the panel. As for every Videofied device, the tamper is active 24/7.If the detector is moved, the TAMPER notification will be displayed on the keypad the next time the system is armed. Press OK/YES to acknowledge that notification and confirm the detector new position. If the TAMPER event is set as ALARM/END, a tamper restoral event is sent to the panel.Longitudinal axis rotationTransverse axis rotationTilt tamper disabling (only for OSMVC version 07.06.04.XX and later)The OSMVC Motionviewer must be deleted from the panel memory to disable tamper.1. Delete the OSMVC from the device configuration menu.2. Press and hold the OSMVC initialization button for 5 seconds. The red LED will turn on for 2 seconds to confirm the setting. 3. Pair the OSMVC back with your panel.The re-enabling tamper procedure is the same as described above. When the tamper is enabled however, the red LED turns on for 2 seconds, turns off for half a second and turns back on for 2 seconds.Streaming optionThe new OSMVC MotionViewer allow the user to request a live video session.The OSMVC is the first battery-powered wireless camera detector emitting on 868MHz able to provide a live video stream from its camera.The 868 MHz frequency has excellent range and allow for excellent battery-life.
5INSTALL SHEET OSMVC OUTDOOR STREAMING MOTION VIEWERInfrared detectionThe OSMVC outdoor MotionViewer uses standard infrared detection. The PIR is optimized for the detection of individuals. Several parameters affect the detection :• Subject thermal signature (size, width, temperature and emissivity).• Detection environment (ambient temperature, reflectivity of the surfaces, the presence of water or moist surfaces).• Speed and direction of the movement.• OSMVC setup (tilt, height, sensitivity).Important :It is essential to monitor the proper functioning of the infrared detection using the FUNCTIONAL TEST feature in the panel MAINTENANCE menu. A red status LED lights up when the OSMVC is detecting. Use that test to determine the pattern of the detection field.Status LEDBlind angleDetection beamsIndividual thermal signature at 3 mIndividual thermal signature at 12 mVehicle thermal signature at 12mDetection curtain(standard sensitivity)1 m4 m12 m
6INSTALL SHEET OSMVC OUTDOOR STREAMING MOTION VIEWERSensitivity adjustmentThe OSMVC detector comes with the capability of adjusting the sensitivity level of the PIR. It can improve the detection or, on the contrary, reduce false alarms. Raising sensitivity will raise detection range, the detection field will be larger and smaller thermal signatures will be detected. You should only use this feature when the site has been diagnosed as needing this adjustment. It cannot be used to optimize detection as the adjustment may be too high and generate either false alarms or missed intrusions.Examples : Plant growth, pets.Please note that the detector must be installed to prevent intrusions (aim the detector towards an access point), sensitivity adjustment will have no effect if the installation doesn’t comply with the installation recommendations described in this document.Adjust sensitivity for the OSMVC MotionViewerTo change the OSMVC sensitivity, you need to change the detector name:DEVICECONFIGURATIONCHANGE NAME DEVICEOK or YESTo select the OSMVCOK or YESEnter the detector name then enter the $ symbol at the end and the chosen digit (without space). The number following $ will depend on the necessary adjustment:SENSITIVITY ADJUSTMENTMINIMAL SENSITIVITY detector_name$2LOW SENSITIVITY detector_name$1DEFAULT SENSITIVITY detector_nameHIGH SENSITIVITY detector_name$8MAXIMAL SENSITIVITY detector_name$9$ SymbolCMA keypad : Press @ repeatedly until $ is displayedXMA/XMB keypad : Press 1 repeatedly until $ is displayed
7INSTALL SHEET OSMVC OUTDOOR STREAMING MOTION VIEWERSecurity notes / (FR) Notes de sécurité / (DE) Hinweise zur SicherheitFrançais• Retirez les piles avant toute opération de maintenance !• Attention ! Il y a un risque d'explosion si la batterie utilisée est remplacée par un mauvais modèle !• Respectez la polarité lors de la mise en place des piles !• Ne jetez pas les batteries usagées ! Ramenez-les à votre installateur ou à un point de collecte spécialisé.English• Remove the batteries before any maintenance !• WARNING, there is a risk of explosion if a battery is replaced by an improper model !• Observe polarity when setting up the batteries!• Do not litter the batteries when they are used! Dispose of them properly according to Lithium Metal requirementsDeutsch• Batterien vor jeglichen Wartungsarbeiten entfernen!• Vorsicht, es besteht Explosionsgefahr, wenn eine Batterie durch eine Batterie falschen Models ersetzt wird!• Achten Sie beim Einsetzen der Batterien auf die Polung! • Entsorgen Sie Batterien nicht im normalen Haushaltsmüll! Bringen Sie Ihre verbrauchten Batterien zu den öffentlichen Sammelstellen.FCC Regulatory Information for USA and CANADAFCC Part 15.21 Changes or modifications made to this equipment not expressly approved by RSI Video Technologies may void the FCC authorization to operate this equipment.FCC Part 15.105 Class B This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:> Reorient or relocate the receiving antenna.> Increase the separation between the equipment and receiver.> Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.> Consult the dealer or an experienced radio/TV technician for help.Radio frequency radiation exposure information according 2.1091 / 2.1093 / OET bulletin 65This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20 cm between the radiator and your body.Cet équipement est conforme aux limites d’exposition aux rayonnements IC établies pour un environnement non contrôlé.Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps.This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.This device complies with Part 15 of the FCC Rules and with Industry Canada licence-exempt RSS standard(s)Operation is subject to the following two conditions:1 This device may not cause harmful interference, and 2 This device must accept any interference received, including interference that may cause undesired operation.Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence.L’exploitation est autorisée aux deux conditions suivantes :1 L’appareil ne doit pas produire de brouillage, et 2 L’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement..
8INSTALL SHEET OSMVC OUTDOOR STREAMING MOTION VIEWERELECTRICAL PROPERTIESRF S2View® technologyRadio type Spread spectrum bidirectionnalOperating frequency• 868MHz - OSMVC 200 (Europe, Africa, Asia)• 915 MHz - OSMVC 601 (USA, Canada, South America)• 920 MHz - OSMVC 702 (Australia, South America)Transmission security AES encryption algorithmSupervision Radio, batteries, tamper, positionRadio antenna IntegratedRADIO PROPERTIESTamper detectionTilt Position change, shock, wall and cover tamperDETECTION PROPERTIESInfrared detection specificationsTechnology Passive infrared DSPType Dual element sensorDetection lens 1 m wide curtainBOXPhysical propertiesMaterial Polycarbonate UL94Dimensions 130,5mm x 102,44mm x 141,5mmWeight 261g (without batteries)Installation / MountingMounting height 2.5 m to 3.5 mMounting angle 5° to 10°Mounting Use mounting kit (sold separately)Environmental dataOperating temperature -25°/+70°CMax. relative humidity 95%, without condensingProtection marking IP 65 / IK 06Power requirements Type C - 4 Lithium batteries 3,6 V LS14500Battery lifeStandard usage (up to 5 videos per month)4 yearsHigh usage (about 30 videos per month)2 yearsStandby current consumption 130 μAMax current consumption 320 mAPanel compatibilityStreaming option W panelsWithout streaming option X and VISIO panelsCameraAngle 90°Sensor type CMOSLighted video Programmable : Color or B&WNight vision video Black & white automatic infraredInfrared illumination Automatic with 4 IR LEDsInfrared illumination distance Up to 12mVideoVideo format H264 (MPEG if not available)Framerate 5 images per secondVideo resolution QVGA (320x240)Average video file size 220 koSnapshotFormat JPEGResolution VGA (640x480)Average snapshot file size 8 koVIDEO PROPERTIES
9www.videofied.comINSTALL SHEET OSMVC OUTDOOR STREAMING MOTION VIEWEREMEA SALES23, avenue du Général Leclerc92340 BOURG-LA-REINEFRANCEE-Mail : emeasales@rsivideotech.comNorth American Headquarters1375 Willow Lake Blvd, Suite 103Vadnais Heights, MN 55110USAE-Mail : usasales@rsivideotech.comThe EC declaration of conformity of this product is available by flashing that QR code :915MHz (OSMVC 601)USA FCC Part 15CCanada IC RSS-247 Issue 1920MHz (OSMVC 702)Australia C-Tick AS/NZS4268This symbol on the product or on its packaging indicates that this product should not be treated as household waste. It must be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health. The recycling of materials will help to conserve natural resources.For more information about recycling of this product, please contact your local municipality, your waste disposal service or the company that installed the product.STANDARDS AND CERTIFICATIONS868MHz (OSMVC 200)Compliant with the annex IV of the R&TTE Directive 1999/5/EC

Navigation menu