Radio Active Design UV-1GBP UV-1G Belt Pack User Manual TITLE GOES HERE

Radio Active Design, LLC UV-1G Belt Pack TITLE GOES HERE

User Manual

Download: Radio Active Design UV-1GBP UV-1G Belt Pack User Manual TITLE GOES HERE
Mirror Download [FCC.gov]Radio Active Design UV-1GBP UV-1G Belt Pack User Manual TITLE GOES HERE
Document ID2147472
Application IDGO6zwjSzoIPgvm0/K7uSmQ==
Document DescriptionUser Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize78.72kB (983949 bits)
Date Submitted2013-12-19 00:00:00
Date Available2014-06-17 00:00:00
Creation Date2013-12-09 12:38:46
Producing SoftwareAdobe PDF Library 10.0
Document Lastmod2013-12-09 12:38:58
Document TitleTITLE GOES HERE
Document CreatorAcrobat PDFMaker 10.1 for Word
Document Author: Dennis Haley

UV-1G
WIRELESS INTERCOM SYSTEM
User Manual
2
•
Per FCC 15.19(a)(3) and (a)(4): This device complies with part 15 of the FCC
Rules. Operation is subject to the following two conditions: (1) This device may
not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
•
Per FCC 15.21: Changes or modifications not expressly approved by Radio
Active Designs could void the user's authority to operate the equipment.
Table of Contents
Table of Contents..................................................................................................................4
General Information ..........................................................................................................6
Features ............................................................................................................................6
Terminology ......................................................................................................................6
UV-1G Specifications ............................................................................................................7
Transmitter .......................................................................................................................7
Receiver ............................................................................................................................8
System Diagram.................................................................................................................9
Base Station ........................................................................................................................10
Front Panel Button Descriptions ......................................................................................10
Front Panel LED Description ............................................................................................12
Rear Panel Description ....................................................................................................13
Belt Pack..........................................................................................................................14
Quick Start Guide ................................................................................................................16
Base Station Operation ....................................................................................................16
Belt Pack..........................................................................................................................16
Base Station Operation .......................................................................................................17
Power ..............................................................................................................................17
Powering Up ................................................................................................................17
Powering Down ...........................................................................................................17
Home Screen ...................................................................................................................18
Transmitter Power Level ..................................................................................................18
Receiver Status ................................................................................................................18
Base Station Link Mode ...................................................................................................18
Local Headset Status........................................................................................................19
RSSI Screen ......................................................................................................................19
Menu Structure...................................................................................................................20
Passcode Protection ........................................................................................................20
Receiver Settings .............................................................................................................20
Transmitter Settings ........................................................................................................21
Local Headset Options .....................................................................................................22
Display Settings ..................................................................................................................23
Blackout Mode ................................................................................................................23
Backlight Time .................................................................................................................24
LCD Brightness.................................................................................................................25
LCD Contrast....................................................................................................................25
LED Brightness .................................................................................................................26
Base Station Link Modes .....................................................................................................26
Info Screen ......................................................................................................................27
Enabling/Disabling the Passcode .....................................................................................27
Changing the Passcode Combine Passcode Sections? ......................................................28
Gain Adjustments ...............................................................................................................29
Intercom 1 & 2 ................................................................................................................29
Auxiliary ..........................................................................................................................29
Stage Announce ..............................................................................................................30
Local Headset ..................................................................................................................30
Microphone Gain .............................................................................................................30
Volume ............................................................................................................................30
Intercom CH1 and CH2 Buttons and LEDs ........................................................................31
Talk Button ......................................................................................................................31
Belt Pack Operation ............................................................................................................31
Battery ............................................................................................................................32
Powering Up ....................................................................................................................32
Powering Down ...............................................................................................................32
Home Screen ...................................................................................................................33
Talk Buttons and LEDs..................................................................................................33
Intercom and Programmable Button Labels .................................................................33
Signal and Battery Meters ...........................................................................................33
Local Headset Volume..................................................................................................33
Power / Menu Button ......................................................................................................34
Menu Structure...................................................................................................................34
Display Settings ...............................................................................................................34
Blackout Mode ................................................................................................................34
Backlight Time .................................................................................................................35
LCD Brightness.................................................................................................................35
LCD Contrast....................................................................................................................36
LED Brightness .................................................................................................................36
Advanced Settings ..............................................................................................................36
Passcode Protection ........................................................................................................37
Transmitter Settings ........................................................................................................37
Receiver Settings .............................................................................................................39
Channel Labels ................................................................................................................40
Soft Button Labels ...........................................................................................................42
Rx Volume Options ..........................................................................................................43
Headset Options ..............................................................................................................44
Info Screen ......................................................................................................................45
Enabling/Disabling the Passcode .....................................................................................45
Changing the Passcode ....................................................................................................45
Microphone Gain .............................................................................................................46
General Information
The Radio Active Designs® UV-1G is a two-channel full-duplex UHF/VHF wireless intercom
system that incorporates up to six wireless belt pack units per base station. Each belt pack is
capable of simultaneous Talk and Listen on two separate audio channels. Additionally, belt
packs have Stage Announce and two-channel Wireless Talk-Around functionality.
The wired interface supports 2W Audiocom® (Telex), RTS® TW, and Clear-Com® varieties.
Support for 4W systems is present through RJ-11 compatible jacks.
Features
•
•
•
•
•
•
•
•
•
•
•
Excellent RF noise immunity through revolutionary design
Full duplex operation incorporates UHF transmitters and VHF receivers
Support for up to six Belt Pack units in one Base Station
Multiple Base Station support when more than six belt packs are linked
Two wireless intercom channels
Programmability via PC interface or User Interface in the field
Internal antenna in the Belt Pack
Very low occupied bandwidth
Frequency Response: 100Hz to 8kHz
Audio Dynamic Range ≥ 50dB
AES-48 Compliant
Terminology
•
•
•
•
•
•
•
•
•
•
•
•
LCD – Liquid Crystal Display
LED – Light Emitting Diode
WTA – Wireless Talk-Around
SA – Stage Announce
4W – 4-Wire
2W – 2-Wire
VHF – Very High Frequency
UHF – Ultra High Frequency
IEC – International Electrotechnical Commission
FCC – Federal Communications Commission
RSSI – Received Signal Strength Indicator
FSTN – Film compensated / Formulated / Filtered Super-twisted Nematic
UV-1G Specifications
RF Frequency Range
Power Requirements
Temperature Range
Dimensions
Base Station
Belt Pack
Weight
Base Station
Belt Pack
TX Antenna
Belt Pack
Base Station
RX Antenna
Belt Pack
Base Station
FCC ID
IC ID
Frequency Response
Four Wire Input
Four Wire Output
Auxiliary Input
Auxiliary Output
Stage Announce Output
Stage Announce Relay
Mic input sensitivity
Local Headset Output
470-608 and 614-98MHz Base Tx, 174-216MHz Belt Tx
100-240 VAC, 50-60 Hz, 2.5A max IEC receptacle
-4º F to 131º F (-20º C to 55º C)
14.68” x 17” x 1.75”
5.55” x 3.78” x 1.83”
7 lbs.
14 Oz
Internal
5/8 wave (Supplied)
Internal
1/4 wave (Supplied)
2AA6F-UV-1GBP, 2AA6F-UV-1GBS
11482A-UV1GBP, 11482A-UV1GBS
100Hz-8 kHz
Level Adjustable (2Vrms typical)
Level Adjustable (2Vrms typical)
Adjustable (2Vrms typical)
Adjustable (2Vrms typical into 600Ω)
Internally Adjustable (2Vrms typical at rated deviation into
600Ω)
Dry Contact, rated at 1 Amp, 24V Max
9mV
40mW output into 600Ω (1% Distortion)
Transmitter
Type
Transmit Power (each transmitter)
Modulation Type
RF Frequency Stability
Occupied Bandwidth
Radiated Harmonics and Spurious
Two Transmitters, Synthesized
100mW, 250mW PEP Max (High Part 74 use only),
10mW, 20mW, 50mW (Part 15 use)
ENB
±1.5ppm
25kHz
Exceeds FCC Specifications
Receiver
Type
RF Sensitivity
Squelch Threshold
IF Selectivity
RF Frequency Stability
Distortion
Direct Conversion
-117dBm for 12dB SINAD
Automatic
25kHz
±1.5 ppm
<1% at full modulation
System Diagram
Base Station
Front Panel Button Descriptions
Figure 1 UV-1G Front Panel Buttons
Power Button: Momentary press to power up unit; press and hold to power off.
Soft Key 1: Menu Navigation; variable button function.
Soft Key 2: Menu Navigation; variable button function.
Rotary Encoder and Select: Rotate for Menu Navigation; press to make selection of a
given menu option.
5. Channel 1 Mute/Unmute: Momentary press to Mute or Unmute Belt Pack #1.
6. Channel 2 Mute/Unmute: Momentary press to Mute or Unmute Belt Pack #2.
7. Channel 3 Mute/Unmute: Momentary press to Mute or Unmute Belt Pack #3.
8. Channel 4 Mute/Unmute: Momentary press to Mute or Unmute Belt Pack #4.
9. Channel 5 Mute/Unmute: Momentary press to Mute or Unmute Belt Pack #5.
10. Channel 6 Mute/Unmute: Momentary press to Mute or Unmute Belt Pack #6.
11. Intercom 1 Output Gain: Momentary press to show Intercom 1 Output Gain screen on
LCD; press and hold to force this screen to persist. See Gain Adjustments section.
12. Intercom 1 Input Gain: Momentary press to show Intercom 1 Input Gain screen on LCD;
press and hold to force this screen to persist. See Gain Adjustments section.
13. Intercom 1 Select: Momentary press toggles Intercom 1 between one of three options:
2-wire, 4-wire, Off.
14. Intercom 2 Output Gain: Momentary press to show Intercom 2 Output Gain screen on
LCD; press and hold to force this screen to persist. See Gain Adjustments section.
15. Intercom 2 Input Gain: Momentary press to show Intercom 2 Input Gain screen on LCD;
press and hold to force this screen to persist. See Gain Adjustments section.
16. Intercom 2 Select: Momentary press toggles Intercom 2 state between one of three
options: 2-wire, 4-wire, off.
17. Auxiliary Output Gain: Momentary press to show Auxiliary Output Gain screen on LCD;
press and hold to force this screen to persist. See Gain Adjustments section.
18. Auxiliary Input Gain: Momentary press to show Auxiliary Input Gain screen on LCD;
press and hold to force this screen to persist. See Gain Adjustments section.
19. Auxiliary Enable/Disable: Momentary press enables or disables Auxiliary Input and
Output.
20. Stage Announce Gain: Momentary press to show Stage Announce Gain screen on LCD;
press and hold to force this screen to persist. See Gain Adjustments section.
1.
2.
3.
4.
10
21. Channel 1 Enable/Disable: Momentary press toggles state of transmitter for local
headset respecting Channel 1.
22. Channel 2 Enable/Disable: momentary press toggles state of transmitter for local
headset respecting Channel 2.
23. Headset Microphone Gain: Momentary press to show Headset Microphone Gain screen
on LCD; press and hold to force this screen to persist. See Gain Adjustments section.
24. Talk Button: Momentary press latches local headset talk on channels determined by the
status of 21 and 22. Press and hold for non-latching operation.
25. Headset Volume: Headset volume audio potentiometer.
11
Front Panel LED Description
Figure 2 Front Panel LED Descriptions
1-6. Channel n Status LED: Green = receiver signal present, flashing Red = belt pack battery
low, alternating Green/Red = receiver signal present and belt pack battery low.
7-12. Channel n Mute LED: Green = channel enabled, Yellow = channel muted, Off = channel
disabled.
13. Intercom 1 2-Wire Enable LED: green = enabled, red = over modulation, off = disabled.
14. Intercom 1 4-Wire Enable LED: green = enabled, red = over modulation, off = disabled.
15. Intercom 2 2-Wire Enable LED: green = enabled, red = over modulation, off = disabled.
16. Intercom 2 4-Wire Enable LED: green = enabled, red = over modulation, off = disabled.
17. Auxiliary Enable LED: green = enabled, red = over modulation, off = disabled.
18. Local Headset Channel 1 Enable LED: green = enabled, off = disabled.
19. Local Headset Channel 1 Status LED: green = local headset traffic on channel 1 (i.e. Talk
button being pressed and local headset channel 1 enabled), red = over modulation,
off = no traffic.
20. Local Headset Channel 2 Enable LED: green = enabled, off = disabled.
21. Local Headset Channel 2 Status LED: green = local headset traffic on channel 2 (i.e. Talk
button being pressed and local headset channel 2 enabled), red = over modulation,
off = no traffic.
22. Power / Fan Fail LED: green = system powered up, red = fan failure condition.
12
Rear Panel Description
Figure 3 Base Station Rear Panel
1. Receive antenna (TNC)
2. Ethernet RJ-45 Port
3. Base Link RJ-45 Port
4. Intercom 1 3-pin XLR Male
5. Intercom 1 3-pin XLR Female
6. Intercom 1 4-wire port
7. Intercom 2 3-pin XLR Male
8. Intercom 2 3-pin XLR Female
9. Intercom 2 4-wire port
10. Transmit Antenna 1 (TNC)
11. Transmit Antenna Selection Switch
12. Auxiliary XLR 3-pin with ¼” audio input
13. Auxiliary XLR 3-pin audio output
14. Stage Announce Relay Contact
15. Stage Announce XLR 3-pin audio output
16. DC Power Input
17. Transmit Antenna 2 (TNC)
13
Belt Pack
Figure 4 Belt Pack Top View
1. Channel 1 Button: at the home screen, push this button to transmit on Channel 1. In the
menu, this button is used to select the item that is boxed.
a. Talk / Over modulation LED for Channel 1: this LED turns on when the Channel 1
talk button is pressed. It is normally green while the transmitter is active for that
button, and it will turn red if over modulation occurs.
2. Channel 2 Button: at the home screen, push this button to transmit on Channel 2. In the
menu, this button is used to select the item that is boxed.
a. Talk / Over modulation LED for Channel 2: this LED turns on when the Channel 2
talk button is pressed. It is normally green while the transmitter is active for that
button, and it will turn red if over modulation occurs.
3. Soft Key 1 Button: at the home screen, push this button to transmit on the userconfigured channel (Channels 1+2, WTA 1, WTA 2, WTA 1+2, SA). In the menu, this is a
“soft key” and will perform the function that is described on the LCD.
a. Talk / Over modulation LED for the Programmable 1 talk button: this LED turns
on when the button is pressed. It is normally green while the transmitter is
active for that button, and it will turn red if over modulation occurs.
4. Soft Key 2 Button: at the home screen, push this button to transmit on the userconfigured channel (Channels 1+2, WTA 1, WTA 2, WTA 1+2, SA). In the menu, this is a
“soft key” and will perform the function that is described on the LCD.
a. Talk / Over modulation LED for the Programmable 2 talk button: this LED turns
on when the button is pressed. It is normally green while the transmitter is
active for that button, and it will turn red if over modulation occurs.
5. LCD with Backlight: The backlight turns on when a button is pressed as long as the belt
pack isn’t set up to blackout the backlight.
14
6
Figure 5 Belt Pack Side Views
6. Auxiliary Ports: USB port and auxiliary audio input.
7. Left Encoder: at the home screen, this adjusts the headset volume for Channel 1. In the
menu, it is used for navigation and changing values.
8. Right Encoder: at the home screen, this adjusts the headset volume for Channel 2. In
the menu, it is used for navigation and changing values.
9. Power / Menu Button: located on the side of the belt pack, a momentary press turns
the belt pack on; press and hold to turn the unit off. When the belt pack is on, a
momentary press will toggle the menu.
11
10
12
Figure 6 Belt Pack Bottom View
10. Headset connector: four pin (shown) or five pin XLR male.
11. Battery Latch.
12. Removable Belt Clip
15
Quick Start Guide
Base Station Operation
1. Power: Insert a standard 120VAC IEC power cable into the power connector located on
the back of the base station.
2. Antennas: Connect antennas to ports on back of Base Station.
3. Connect Headset: Insert the headset connector into the base station until it snaps into
place.
4. Powering Up: Press the power button. The display will turn on as well as various LEDs.
5. Tx & Rx Frequencies: Program the transmitter and receiver frequencies as desired. See
Section 6: Base Station Operation or Section 8: PC Application for information on how to
program frequencies from the Base Station itself or from the PC Application. Note: the
defaults for Rx 1 – Rx 6 are 175MHz, 176MHz, 177MHz, 178MHz, 179MHz, and 180MHz.
The default for Tx1 is 519MHz and Tx2 is 520MHz.
6. Intercom 2W / 4W:
Belt Pack
1. Batteries: Place five (5) new “AA” lithium or alkaline batteries into the provided battery
sled, in the correct polarity.
2. Connect Headset: Insert the headset connectors into the belt packs until they snap into
place.
3. Powering Up: Press the Power / Menu button that is located on the side of the belt
pack. The display will turn on and the belt pack will power on.
4. Tx & Rx Frequencies: Program the transmitter and receiver frequencies as desired. See
Section 7: Belt Pack Operation or Section 8: PC Application for information on how to
program frequencies from the Belt Pack itself or from the PC Application. Note: the
default for Rx1 is 519MHz, Rx2 is 520MHz, and Tx is 175MHz. These values will work
with the Base Station defaults for one belt pack (belt pack #1). The other belt packs will
need their frequencies changed from the defaults. See notes above.
Congratulations, your new base station is ready for use!
16
Base Station Operation
Figure 7 Base Station
Power
The Base Station is powered by 120VAC, 2.5A (max) using a standard IEC power cable to a
low voltage power supply.
Powering Up
To turn the Base Station on, press the POWER button as shown in Figure 7 above. While the
Base Station powers up, a splash screen will appear.
RADIO
ACTIVE
DESIGNS . . .
Once the Base Station is ready for use, the Home Screen will be displayed.
Powering Down
To turn the Base Station off, press and hold the POWER button until the LCD screen goes
blank.
17
Home Screen
The Home Screen is the root of the UV-1G Base Station UI. It displays information regarding
transmitter power level, receiver status, base station link mode, and local headset status. The
left portion of the screen provides links to the main menu and RSSI screens.
MENU....M.........R1 C1...R4 OFF
MENU....T1 50mW...R2 C2...R5 NTx
MENU....T2 50mW...R3 OFF..R6 W1
RSSI....HS: OFF
MENU....M.........R1 C1...R4 OFF
MENU....T1 50mW...R2 C2...R5 NTx
MENU....T2 50mW...R3 OFF..R6 W1
RSSI....HS: OFF
Transmitter Power Level
The indicators T1 and T2 represent Transmitter 1 and Transmitter 2. The options for these
are: OFF, 10mW, 20mW, 50mW (Part 15), and 100mW, 250mW (Part 74 only).
See TRANSMITTER SETTINGS for details on changing these parameters.
Receiver Status
The indicators R1 through R6 represent the status of a given receiver (transmit status for
each belt pack).
The table below shows the different receiver status codes along with their meaning.
Code
OFF
NTx
C1
C2
C12
W1
W2
W12
SA
Meaning
Receiver is off (disabled).
Receiver is enabled and the belt pack is not transmitting.
(Intercom) Channel 1
(Intercom) Channel 2
(Intercom) Channels 1 & 2
Wireless-Talk-Around 1
Wireless-Talk-Around 2
Wireless-Talk-Around 1 & 2
Stage Announce
Base Station Link Mode
The Base Station Link Mode status appears on the Home Screen above the power level
indication for transmitter 1 (T1).
The letter M stands for master and S for slave.
Two base stations can be linked to expand the number of belt packs that a system can
handle.
18
Local Headset Status
The Local Headset Status information is labeled as HS. The table below shows the different
Local Headset Status codes along with their meaning.
Code
OFF
T/L
LO
Meaning
Local headset is disabled.
Local headset is enabled. Talk and listen capability is enabled.
Local headset is enabled. Transmit functionality is disabled (listen only).
RSSI Screen
To get to the RSSI (Received Signal Strength Indication) screen, press the bottom soft key
labeled RSSI.
MENU....M.........R1 C1...R4 OFF
MENU....T1 50mW...R2 C2...R5 NTx
MENU....T2 50mW...R3 OFF..R6 W1
RSSI....HS: OFF
RSSI
BACK
RSSI
BACK
R1
R2
R3
BACK
R4
R5 OFF
R6 OFF
The RSSI screen, shown above, displays the signal strength of each receiver. Presence of the
word OFF means that particular receiver is disabled.
19
Menu Structure
Passcode Protection
The base station menu can be protected by a passcode.
When the MENU button is pressed from the home screen the screen will change as follows:
MENU....M.........R1 C1...R4 OFF
MENU....T1 50mW...R2 C2...R5 NTx
MENU....T2 50mW...R3 OFF..R6 W1
RSSI....HS: OFF
MENU
BACK
INFO......Enter the Passcode:
MENU....*
MENU........0....*....*....*
BACK....
The passcode is four digits long and each digit can be any 0 – 9 number.
• Press SELECT to change the selected (boxed) digit.
• Once the last digit is entered, press SELECT.
If the entered passcode is correct, the menu screen will be displayed. If it is incorrect,
“Invalid Passcode” will be displayed for three seconds before returning to the home screen.
See ENABLING/DISABLING THE PASSCODE and CHANGING THE PASSCODE for instructions
on how to enable/disable and change the passcode.
Receiver Settings
The receiver settings allow the user to change the receiver frequencies, as well as enable or
disable them.
To get to the receiver settings, from the home screen, press MENU then press SELECT on RX
SETTINGS. The screen will appear as follows:
............179.450
........R2: 202.020
BACK....R3: 215.300
R1: 179.450
............
........R2: 202.020
BACK....R3: 215.300
20
This screen displays the frequency (in MHz) of all six receivers.
If a given receiver is disabled, the word DISABLED will appear in place of a numerical
frequency value.
• Use the rotary encoder to navigate to the desired receiver and press SELECT to
change the receiver frequency or status (enabled / disabled).
The following is an example of selecting R1:
........R1 Freq : 179.450
........
Status: Enabled
........
BACK....
........R1 Freq
Freq : 179.450
........
Status: Enabled
........
BACK....
•
•
•
•
To change the frequency, press SELECT and the first frequency digit will be boxed
(see below).
Use the encoder to change the value of the boxed digit (up / down).
Press SELECT to move on to the next digit.
Once the frequency has been changed as desired, press SAVE to save the change or
BACK to cancel.
SAVE....R1 Freq : 179.450
Status: Enabled
........
........
BACK....
SAVE....R1 Freq : 1
179.450
........
Status: Enabled
........
BACK....
•
•
Up
Down
To change the status, scroll down to STATUS and press SELECT.
Use the encoder to change the selection and press SAVE to save the change.
........R1 Freq : 179.450
Status: Enabled
........
........
BACK....
........R1 Freq : 179.450
Status: Enabled
........ Status:
........
BACK....
Select
SAVE....R1 Freq : 179.450
Status: Enabled
........
........
BACK....
SAVE....R1 Freq : 179.450
........ Status: Enabled
Enabled
........
BACK....
Up
Down
Transmitter Settings
The transmitter settings allow the user to change the transmitter frequencies and power
levels as well as enabling/disabling them.
• To get to the transmitter settings from the home screen, press MENU, scroll down
to “Tx Settings,” and press SELECT.
The screen will appear as follows:
21
............50mW....470.000
........T2: 50mW....471.040
........
BACK....
............
T1: 50mW....470.000
........T2: 50mW....471.040
........
BACK....
This screen lists the frequency (in MHz) of both transmitters, the power level, and the status
(enabled/disabled). For example if transmitter one is disabled, T1: DISABLED will be displayed.
If it is enabled, then it will be displayed as it is shown above.
• To change any of these settings, scroll to the transmitter you desire to change, press
SELECT and the screen will appear as follows:
........T1..........50mW
.............Freq : 470.000
........
BACK....
Power: 50mW
........T1..........
.............Freq : 470.000
........
BACK....
•
•
•
To change the transmitter power, press SELECT.
Use the encoder to change the value.
Press SAVE to save or BACK to cancel the change.
SAVE....T1...Power:
.............Freq : 470.000
........
BACK....
SAVE....T1...Power: 50mW
.............Freq : 470.000
........
BACK....
•
•
•
Up
Down
To change the frequency, select FREQ and the first frequency digit will be boxed (see
below).
Use the encoder to change the boxed digit and press SELECT to change which digit is
boxed.
Press SAVE to save the change or BACK to cancel.
........T1...Power: 50mW
....................470.000
........
BACK....
........T1...Power: 50mW
Freq : 470.000
....................
........
BACK....
Select
SAVE.....T1...Power: 50mW
..............Freq : 70.000
........
BACK....
SAVE.....T1...Power: 50mW
..............Freq : 470.000
........
BACK....
Up
Down
Note: For operation under Part 15 of FCC Rules, the maximum transmitter power is 50mW.
Higher power requires a license under Part 74 of the FCC Rules.
Local Headset Options
There are two local headset options: Status or Earphones.
22
The Status setting allows the local headset to be disabled, set up as listen only, or as a fully
functioning headset (talk and listen).
The Earphone’s setting controls where the receiver audio gets routed, to the left and/or
right earphones.
If Separate is selected, audio from Receiver 1 will be routed to the right earphone and audio
from Receiver 2 will be routed to the left earphone.
If Combined is chosen, audio from both receivers will be routed to both earphones.
Note: If only one receiver is enabled, then the audio from that receiver will be routed to
both earphones no matter what option is chosen. These options are located in the menu under
“Local Headset.”
....................Talk/Listen
BACK....Earphones : Combined
BACK....
Status
: Talk/Listen
....................
BACK....Earphones : Combined
BACK....
Down
SAVE....Status
:.Talk/Listen
BACK....Earphones : Combined
BACK....
Select
Down
Up
: Talk/Listen
........Status
BACK....Earphones : Combined
BACK....
: Talk/Listen
........Status
Earphones : Combined
BACK....Earphones
BACK....
SAVE....Status
:.Talk
/Listen
Talk/Listen
BACK....Earphones : Combined
BACK....
Down
Up
SAVE....Status
:.Talk/Listen
BACK....Earphones : Combined
BACK....
Select
Up
SAVE....Status
:.Talk/Listen
BACK....Earphones : Combined
Combined
BACK....
Up
Down
Display Settings
Blackout Mode
.........................OFF
........Backlight Time : 10S
BACK....LCD.Brightness.: 3
.........................
Blackout Mode : OFF
........Backlight Time : 10S
BACK....LCD.Brightness.: 3
SAVE....Blackout Mode :
........Backlight Time : 10S
BACK....LCD Brightness : 3
Select
SAVE....Blackout Mode : OFF
........Backlight Time : 10S
BACK....LCD Brightness : 3
Up
Down
23
Blackout Mode allows the user to disable all the LEDs on the base station.
• To get to blackout mode screen, from the home screen, press MENU, scroll down to
Display Settings and press SELECT.
Blackout mode is the first display setting. There are four options: OFF, LEDs, BKLGHT
(backlight), and ON.
ON means that both the backlight and LEDs will be disabled.
OFF means that both the backlight and LEDs operate normally.
LEDs means that just the LEDs will be disabled or blacked out.
BKLGHT means that just the backlight will be disabled or blacked out.
•
•
To change the blackout mode, press SELECT and then turn the encoder as shown
above.
Press the SAVE button to save the change or press BACK to ignore it.
Backlight Time
........Blackout Mode : OFF
.........................10S
BACK....LCD Brightness : 3
........Blackout Mode : OFF
Backlight Time : 10S
.........................
BACK....LCD Brightness : 3
SAVE....Blackout Mode : OFF
........Backlight Time :
BACK....LCD Brightness : 3
Select
SAVE....Blackout Mode : OFF
........Backlight Time : 10S
BACK....LCD Brightness : 3
Up
Down
The Backlight Time setting changes the amount of time the backlight stays on for.
• To get to the backlight time screen, from the home screen, press MENU, scroll down
to DISPLAY SETTINGS and press SELECT.
Backlight time is the second display setting. Each time any button is pressed or the encoder
is turned the backlight timer gets reset.
The choices are:
5S for 5 seconds
10S for 10 seconds
20S for 20 seconds
30S for 30 seconds
60S for 60 seconds
ON meaning it will never turn off.
•
•
•
To change the backlight time, press SELECT.
Turn the encoder as shown above.
Press SAVE to save the change or BACK to ignore it.
24
LCD Brightness
SAVE....Blackout Mode : OFF
........Backlight Time : 10S
BACK....LCD Brightness :
........Blackout Mode : OFF
........Backlight Time : 10S
BACK.....................3
........Blackout Mode : OFF
........Backlight Time : 10S
BACK.....................
LCD Brightness : 3
Select
SAVE....Blackout Mode : OFF
........Backlight Time : 10S
BACK....LCD Brightness : 3
Up
Down
The LCD brightness setting changes the brightness of the LCD’s backlight.
• To get to the LCD brightness screen, from the home screen, press MENU, scroll
down to Display Settings and press SELECT.
LCD Brightness is the third display setting. The choices are 1 – 5, with 1 being dim and 5
being the brightest.
• To change the brightness, press SELECT.
• Turn the encoder as shown above.
• Press SAVE to save the change or press BACK to ignore it.
Note: the brightness updates in real time as it is modified.
LCD Contrast
SAVE....Backlight Time : 10S
........LCD Brightness : 3
BACK....LCD Contrast
........Backlight Time : 10S
........LCD Brightness : 3
BACK.....................7
........Backlight Time : 10S
........LCD Brightness : 3
BACK.....................
LCD Contrast
: 7
Select
SAVE....Backlight Time : 10S
........LCD Brightness : 3
BACK....LCD Contrast : 7
Up
Down
The LCD contrast setting changes the display’s contrast.
• To get to the LCD contrast screen, from the home screen, press MENU, scroll down
to DISPLAY SETTINGS and press SELECT.
LCD contrast is the fourth display setting. The choices are 1 – 11, with 1 being the dimmest
and 11 being the brightest.
• To change the contrast, press SELECT.
• Turn the encoder as shown above.
• Press SAVE to save the change or press BACK to ignore it.
Note: the contrast updates in real time as it is modified.
25
LED Brightness
........LCD Brightness : 3
........LCD Contrast
: 7
BACK.....................3
........LCD Brightness : 3
........LCD Contrast : 7
LED Brightness : 3
BACK.....................
SAVE....LCD Brightness : 3
: 7
........LCD Contrast
BACK....LED Brightness :
Select
SAVE....LCD Brightness : 3
........LCD Contrast : 7
BACK....LED Brightness : 3
Up
Down
The LED brightness setting changes the talk buttons LED’s brightness.
• To get to the LED brightness screen, from the home screen, press MENU, scroll
down to Display Settings and press SELECT.
LED brightness is the last display setting. The choices are 1 – 5, with 1 being the dimmest
and 5 being the brightest.
• To change the brightness, press SELECT.
• Turn the encoder as shown above.
• Press SAVE to save the change or press BACK to ignore it.
Note: the brightness updates in real time as it is modified.
Base Station Link Modes
Two base stations can be “linked” together to expand the number of belt packs that the
system can handle.
The two options are Master and Slave. When two base stations are “linked” together, one
must be set up as a master and the other as a slave.
The master base station works just like a normal base station except it will receive audio
from the slave base station that it will route.
The slave base station receives up to six belt packs’ audio and gives it to the master to
route. The slave’s transmitters and all the ports on the back of the base station will be disabled.
• To change the base station link mode, go to LINK SETTINGS in the menu, and press
SELECT.
• Turn the encoder to the desired setting and
• press SAVE.
SAVE....Local Headset
........Display Settings
BACK....Link Settings : Master
EXIT....Local Headset
........Display Settings
........
Master
EXIT....Local Headset
........Display Settings
........Link Settings: Master
Select
SAVE....Local Headset
........Display Settings
BACK....Link Settings: Master
Master
Up
Down
26
Info Screen
The Info screen displays a version number and serial number of the base station. The
version number is a composite firmware version number of all the firmware running in the base
station.
........VER:.XX.XXX
........SN.:.XXXXXXXX
EXIT....Display Settings
........Link Settings : Master
EXIT....Display Settings
........Link Settings: Master
Info
Select
........VER:.XX.XXX
........SN.:.XXXXXXXX
BACK
BACK
The Info screen is located in the menu right below LINK SETTINGS. To view the screen,
press SELECT as shown above.
Enabling/Disabling the Passcode
The Menu can be passcode protected. The passcode is a four digit 0 – 9 number.
SAVE....Link Settings : Master
........Info
BACK....Passcode : Disabled
EXIT....Link Settings : Master
........Info
........Passcode : Disabled
EXIT....Link Settings: Master
........Info
........Passcode
Passcode:: Disabled
Select
SAVE....Link Settings: Master
........Info
BACK....Passcode: Disabled
Disabled
Up
Down
The passcode can be enabled or disabled from the PASSCODE screen. It is located below
the Info screen in the Menu as shown above.
• To change the setting, press SELECT.
• Turn the encoder until the desired option appears
• Press SAVE.
27
Changing the Passcode Combine Passcode Sections?
The Passcode can be changed by selecting Change Passcode in the Menu.
• Select Change Passcode
• Enter the desired new passcode (pressing SELECT to advance to the next digit)
• Press SAVE
• Re-enter the desired new passcode
• Pressing SAVE once finished.
If the two passcodes that were just entered match, then the passcode will be changed to
that value. If they don’t match, then the passcode will remain unchanged.
SAVE......Enter New Passcode :
MENU....
MENU........0....*....*....*
BACK....
EXIT....Info
........Passcode : Disabled
........
EXIT....Info
........Passcode: Disabled
........Change Passcode
Select
SAVE......Enter New Passcode:
MENU....
MENU........0
*....*....*....*
BACK....
Save
SAVE.....Re-enter New Passcode :
MENU....
MENU........0....*....*....*
BACK....
SAVE.....Re-enter New Passcode:
MENU....
MENU........0
*....*....*....*
BACK....
Save
Save
EXIT....
MENU.......Passcode.Changed .
MENU....
BACK....
EXIT....
MENU.......Passcode.Changed.
MENU....
BACK....
BACK....
MENU....Error: Passcodes don’t
MENU....
match.
BACK....
BACK....
MENU....Error: Passcodes don’t
MENU....
match.
BACK....
28
Gain Adjustments
Gain adjustments can be made to the following:
Intercom 1 inputs and outputs (2W and 4W)
Auxiliary inputs and outputs, and
Stage Announce (and the local headset microphone which is described in the Local Headset
section)
All gains have eleven (11) settings.
• To change one of the gain settings, press the appropriate gain button and then use
the encoder to adjust it.
The gain screen will go away after 30 seconds if no button press or encoder knob turn is
made.
When changing one of the gains a bar graphic along with a number will be displayed on the
screen to show the current setting.
A label telling what gain it is and a status (when applicable) is also shown.
• Turn the encoder knob clockwise to increase the gain and counter clockwise to
decrease the gain. The change will take place immediately.
• When finished, press SAVE to save the change, otherwise press BACK, or wait for the
timeout to cancel any changes (the value will revert back).
Note: Stage Announces’ gain can be changed at anytime, however Intercom 1 and 2 and
Auxiliary need to be enabled to be able to change their gains.
Intercom 1 & 2
SAVE...COM 1 4W Input Gain
SAVE...COM 1 4W Input Gain
BACK...Status: Enabled
BACK...Status: Enabled
The figure above shows an example of what an Intercom gain screen looks like. Note: the
Intercom must be enabled to change the gain.
Auxiliary
SAVE...Aux Input Gain
SAVE...Aux Input Gain
BACK...Status: Enabled
BACK...Status: Enabled
29
The figure above shows an example of what an Auxiliary gain screen looks like. Note:
Auxiliary must be enabled to change the gain.
Stage Announce
SAVE...SA Gain
SAVE...SA Gain
BACK...
BACK...
The figure above shows what the Stage Announce gain screen looks like.
Local Headset
Microphone Gain
•
Change the local headset microphone gain by pressing the Mic Level button (below
the Talk button).
The display will change as shown below.
• Use the encoder to change the gain, and press SAVE to save the change or BACK to
ignore it.
Note: the microphone gain updates in real time as it is modified.
SAVE...Mic Gain
SAVE...Mic Gain
BACK...
BACK...
Volume
The local headset volume is control by a knob, located to the right of the TALK and MIC
level buttons.
30
Intercom CH1 and CH2 Buttons and LEDs
These two buttons allows the base station user to transmit on Intercom Channel 1,
Intercom Channel 2 or both.
When enabled the audio will be routed through that intercom channel (and not routed
when it is disabled).
There are two LEDs above each of these buttons:
• The one on the left is a green LED that is on when that channel is enabled and off
when disabled.
• The LED on the right is a red and green LED combo. It is green when that intercom
channel’s audio is being routed and the talk button is pressed and red when this is
true plus the user’s microphone is over modulating.
Talk Button
The Talk button allows the base station user to transmit. The button can be pressed and
held or “tapped” on and off.
Belt Pack Operation
Figure 8 Belt Pack Power Button
31
Battery
Before the belt pack is turned on, be sure to attach a fresh battery pack. During operation,
the battery meter will display the battery’s status.
Powering Up
To turn the belt pack on, press the power button as shown in Figure 8 above. While the belt
pack is powering on, a splash screen will be displayed.
RADIO
ACTIVE
DESIGNS . . .
Once the belt pack is ready to go, the home screen will be displayed.
Powering Down
To turn the belt pack off, press and hold (approximately 3 seconds) the power button until
the LCD screen goes blank.
32
Home Screen
Talk Buttons and LEDs
The belt pack has four talk buttons with a corresponding set of green and red LEDs.
The top two talk buttons, Intercom Channel 1 and Intercom Channel 2, are fixed in
functionality although the label names are programmable.
The bottom two talk buttons are programmable with the following choices:
• Intercom Channels (CH) 1 & 2
• Wireless-Talk-Around (WTA) 1
• Wireless-Talk-Around (WTA) 2
• Wireless-Talk-Around (WTA) 1 & 2
• Stage Announce (SA).
The home screen displays this information in the four boxes in the corners of the screen.
Each talk button has a green and red LED set.
The green LED turns on to show that the transmitter is active for that channel.
The red LED turns on when microphone over modulation occurs while transmitting.
Intercom and Programmable Button Labels
The home screen displays a boxed “T” next to each talk button label box to show the
transmitter’s status for each button.
The “T” means that the transmitter is on, and a box around the “T” means that the mic is
unmuted.
Note: it is possible to turn on the transmitter with the microphone muted (no audio is
transmitted).
Signal and Battery Meters
The signal and battery meters are there to assist the user.
The signal meter is an average of both receiver’s signal strength if both are enabled, or if
just one receiver is enabled it is that receiver’s signal strength.
The battery meter displays the battery’s status.
Local Headset Volume
The headset volume is changeable via the two knobs:
• Left changes Channel One
• Right changes Channel Two
If the local headset volume option is set to COMBINED, both knobs change volume of both
receivers proportionally.
33
Power / Menu Button
This button is used to turn on and off the belt pack, as well as to get into and out of the
menu.
• When the belt pack is off, press the button to turn it on.
• When on, press and hold (approximately 3 seconds) to turn it off.
• To get into or out of the menu, when the belt pack is on, press (without holding) the
button.
Menu Structure
Display Settings
•
To get to the display settings from the home screen, press the MENU button.
The screen will appear as follows:
Advanced Settings
Mic G
Exit

Display Settings
Advanced Settings
Mic G
Exit

•
Press SELECT.
Up
ow
ow
Blackout.Mode.:
Backlight.Time: 10S
SAVE
BACK
................OFF
Backlight.Time: 10S
BACK
Blackout
Mode : OFF
................
Backlight.Time: 10S
BACK
Up
Blackout Mode
Select
Blackout.Mode.: OFF
Backlight.Time: 10S
SAVE
BACK
Blackout mode is the first display setting. It allows the LCD backlight and/or the talk LEDs to
be disabled or “blacked out”.
There are four options: OFF, LEDs, BKLGHT (backlight), and ON.
ON means that both the backlight and LEDs will be disabled, and
OFF means that both the backlight and LEDs operate normally.
LEDs means the LEDs will be disabled or blacked out, and likewise
BKLGHT means the backlight will be disabled or blacked out.
• To change the blackout mode, press SELECT
• turn either encoder as shown above.
• Press SAVE to save the change or BACK to ignore it.
34
Blackout.Mode.:.OFF
Backlight
Time: 10S
................
BACK
Up
ow
Blackout.Mode.:.OFF
................10S
BACK
ow
Up
Backlight Time
Blackout.Mode : OFF
Backlight.Time:
SAVE
BACK
Select
Blackout.Mode : OFF
Backlight.Time: 10S
SAVE
BACK
The backlight time setting changes the amount of time the backlight stays on for.
Each time any button is pressed or encoder is turned the backlight timer gets reset.
The choices are:
5S for 5 seconds
10S for 10 seconds
20S for 20 seconds
30S for 30 seconds
60S for 60 seconds
ON meaning it will never turn off.
•
•
•
To change the backlight time, press SELECT
turn either encoder as shown above.
Press SAVE to save the change or BACK to ignore it.
Up
ow
Backlight.Time: 10S
LCD.Brightness:
................
BACK
ow
Backlight.Time: 10S
................3
BACK
Up
LCD Brightness
Backlight.Time:.10S
LCD.Brightness:
SAVE
BACK
Select
Backlight.Time:.10S
LCD.Brightness: 3
SAVE
BACK
The LCD brightness setting changes the brightness of the LCD’s backlight.
The choices are 1 – 5, with 1 being the dimmest and 5 being the brightest.
• To change the brightness, press SELECT
• Turn either encoder as shown above.
• Press SAVE to save the change or BACK to ignore it.
Note: the brightness updates in real time as it is modified.
35
Up
ow
ow
Up
LCD Contrast
LCD.Brightness: 3
LCD.Contrast..:
SAVE
BACK
LCD.Brightness:.3
................7
BACK
:.3
LCD.Brightness
LCD
Contrast : 7
................
Select
BACK
LCD.Brightness: 3
LCD.Contrast..: 7
SAVE
BACK
The LCD contrast setting changes the display’s contrast.
The choices are 1 – 11, with 1 being the dimmest and 11 being the brightest.
•
•
•
To change the contrast, press SELECT
Turn either encoder as shown above.
Press SAVE to save the change or BACK to ignore it.
Note: the contrast updates in real time as it is modified.
Up
ow
ow
Up
LED Brightness
LCD.Contrast : 7
LED.Brightness:
SAVE
BACK
LCD.Contrast : 7
................3
BACK
LCD.Contrast
: 7
LED
Brightness: 3
................
Select
BACK
LCD.Contrast : 7
LED.Brightness: 3
SAVE
BACK
The LED brightness setting changes the talk buttons LED’s brightness.
The choices are 1 – 5, with 1 being the dimmest and 5 being the brightest.
•
•
•
To change the brightness, press SELECT
Turn either encoder as shown above.
Press SAVE to save the change or BACK to ignore it.
Note: the brightness updates in real time as it is modified.
Advanced Settings
•
To get to the advanced settings, from the home screen, press the MENU button.
36
The screen will look like this:
Advanced Settings
Mic G

Exit
Display Settings
Advanced Settings
Mic G

Exit
•
•
Use either encoder to scroll down to Advanced Settings.
Once it is boxed, press SELECT.
Passcode Protection
The advanced menu can be passcode protected if desired.
When the passcode is enabled, once the user presses select on ADVANCED SETTINGS, the
screen will appear as follows:
....Enter.Passcode:
.*..*..*..*
....Enter.Passcode:
INFO..............BACK
.*..*..*..*
INFO..............BACK
The passcode is four digits where each digit can be any 0 – 9 number.
• Use either encoder to change the selected digit.
• Press SELECT to change the selected (boxed) digit.
• Once the last digit is entered press SELECT.
If the entered passcode is correct the belt pack will go to the advanced settings.
If it is incorrect Invalid Passcode will be display for three seconds before returning to the
main menu.
See ENABLING/DISABLING THE PASSCODE and/or CHANGING THE PASSCODE at the end of
this section for more information.
Transmitter Settings
The transmitter settings allow the user to change the transmitter power level, frequency,
status, and Intercom transmit settings.
The transmitter settings are located in the ADVANCED SETTINGS sub-menu.
Once selected, the screen will appear as follows:
T1.............50mW
....Freq.....:.214.000
..................BACK
: 50mW
Power
T1.............
....Freq.....:.214.000
BACK
..................
37
•
•
Up
ow
ow
Up
To change the transmitter power level, press SELECT.
Use either encoder to change the value and press SAVE to save or BACK to ignore
the change.
The choices are 10mW and 50mW.
T1..Power....:
....Freq.....:.214.000
SAVE..............BACK
T1..Power....: 50mW
....Freq.....:.214.000
SAVE..............BACK
•
•
•
•
To change the frequency, scroll down to box FREQ: press SELECT and the first
frequency digit will be boxed (see below).
Use either encoder to change the boxed digit
Press SELECT to change which digit is boxed.
Press SAVE to save the change or BACK to ignore it.
The belt pack transmitter frequency range is 174 MHz – 216 MHz (VHF), and the step size if
5 kHz.
Up
Up
ow
ow
T1..Power....:.50mW
Freq
: 214.000
...............
BACK
..................
T1..Power....:.50mW
...............214.000
..................BACK
T1..Power....:.50mW
....Freq.....:..14.000
SAVE..............BACK
Select
T1..Power....:.50mW
214.000
....Freq.....:..
SAVE..............BACK
Up
ow
Save / Back
Select
T1..Freq....:.214.000
Status : Enabled
..............
..................
BACK
ow
T1..Freq....:.214.000
..............Enabled
..................BACK
Up
The status is the “master” control for the transmitter.
If it is set to disabled then the transmitter will be powered down, and all transmit
functionality of the belt pack will be disabled.
If it is set to enabled then the belt pack will function normally, transmitting when a transmit
button is pressed.
• To change the status, scroll down until STATUS: is boxed and press SELECT.
• Use either encoder to change the status and press SAVE to save and BACK to ignore
the change.
T1..Freq....:.214.000
....Status..:.Enabled
..................BACK
T1..Freq....:.214.000
Enabled
....Status..:.Enabled
..................
BACK
The last two items in the transmitter settings are called ICOM1 Tx and ICOM2 Tx.
38
These control whether the belt pack user is allowed to transmit on Intercom CH 1 and
Intercom CH 2.
ENABLED = allowed
DISABLED = not allowed
ow
Up
Save / Back
Select
T1..Status..:.Enabled
ICOM1 Tx: Enabled
..............
..................
BACK
ow
T1..Status..:.Enabled
..............Enabled
..................BACK
Up
Please note that these don’t affect Wireless-Talk-Around 1 or 2 (they are controlled
separately). They only affect Intercom Channels 1 and 2.
• To change either of these values scroll down until it is boxed and press SELECT.
• Use either encoder to change the status and press SAVE to save and BACK to ignore
the change.
T1..Status..:.Enabled
....ICOM1.Tx:.Enabled
..................BACK
T1..Status..:.Enabled
Enabled
....ICOM1.Tx:.Enabled
..................
BACK
Up
ow
Save / Back
Select
T1..ICOM1.Tx:.Enabled
ICOM2 Tx: Disabled
..............
..................
BACK
ow
T1..ICOM1.Tx:.Enabled
..............Disabled
..................BACK
Up
Up/Down
T1..ICOM1.Tx:.Enabled
....ICOM2.Tx:.Disabled
..................BACK
T1..ICOM1.Tx:.Enabled
Disabled
....ICOM2.Tx:.Disabled
..................
BACK
Receiver Settings
The receiver settings allow the user to change the receiver frequencies as well as
enable/disable them.
The receiver settings are located in the ADVANCED SETTINGS sub-menu.
Once selected, the screen will appear as follows:
....470.000
R2: 498.000
BACK
R1:
....470.000
R2: 498.000
BACK
This screen lists the frequency (in MHz) of both receivers as well as the status.
For example if receiver one is disabled, R1: Disabled will be displayed.
If a frequency is listed instead of Disabled, then it is enabled and receiving at the specified
frequency.
• To change a receivers’ frequency or status, scroll to the receiver you desire to
change
39
•
Press SELECT and the screen will change to the following:
R1.Freq..:.470.000
...Status:.Enabled
BACK
Freq:
R1.Freq
..:.470.000
...Status:.Enabled
BACK
•
•
•
To change the frequency, press SELECT and the first frequency digit will be boxed
(see below).
Use the encoder to change the boxed digit and press SELECT to change which digit is
boxed.
Once the frequency has been changed as desired, press SAVE to save the change or
BACK to ignore it.
ow
Up
ow
Up
The belt pack receiver frequency range is 470-608MHz and– 614-698MHz (UHF), and the
step size is 5kHz.
R1.Freq..:.470.000
...Status:.Enabled
SAVE
BACK
R1.Freq..:.470.000
...Status:.Enabled
SAVE
BACK
Up
ow
ow
R1.Freq..:.470.000
...Status:.Enabled
BACK
Up
The status enables (turns on) / disabled (turns off) the receiver.
Turn off an un-needed receiver to save battery power.
• To change the status, scroll down to box Status and press SELECT.
• Turn the encoder to change the selection
• Press SAVE to save the change.
R1.Freq..:.470.000
...Status:.Enabled
SAVE
BACK
R1.Freq..:.470.000
...Status:
Status:.Enabled
Select
BACK
R1.Freq..:.470.000
...Status:.Enabled
Enabled
SAVE
BACK
Channel Labels
The Channel Labels menu option in the Advanced Settings sub-menu provides a way to
change the (Intercom) Channel talk button labels.
40
Channel 1
Button Label
Channel 2
Button Label
BATT:
DIRECTOR
SIG:
CAMERA 1
SIG:
BATT:
SA
WTA 1&2
This sub-menu allows the user to change, edit, remove, and add new labels. Once the
Channel Labels menu is entered, the screen will appear as follows:
Edit/Remove Labels
BACK
Change Labels
Edit/Remove Labels
BACK
•
•
•
•
Press SELECT to change what label is assigned to each Intercom.
Intercom CH 1 is on the left.
Intercom CH 2 is on the right.
Press SELECT to change which one gets changed.
Use either encoder to scroll through the list of labels.
Press SAVE to save your changes or BACK to ignore them.
Director
CameraBACK1
SAVE
Camera 1
Director
Camera BACK
SAVE
Director
Select
SAVE
BACK
SAVE
BACK
•
To view the label list, or edit or remove a label, select the Edit/Remove Labels
option in the Channel Labels sub-menu.
The screen will appear as follows:
.IRECTOR
CAMERA 1
REMOVE............BACK
DIRECTOR
CAMERA 1
REMOVE............BACK
•
•
.IRECTOR
SAVE.....[A-Z]....BACK
Select
SAVE.....[A-Z]....BACK
Use either encoder to scroll through the list.
Press SELECT to edit the currently selected label.
The left (CH 1) encoder changes the currently selected character.
The right (CH 2) encoder changes the group.
There are three groups: capital letters (A-Z), numbers (0-9), and symbols (SYM).
41
•
•
Press SELECT to change the selected character.
Press the left soft key labeled REMOVE to remove the currently selected label as
shown below.
Are you sure you want
to remove DIRECTOR ?
NO
YES
CAMERA 1
REMOVE............BACK
DIRECTOR
CAMERA 1
REMOVE............BACK
Remove
Are you sure you want
to remove DIRECTOR?
NO
YES
Yes
DIRECTOR removed !
DIRECTOR removed!
....................OK
OK
....................
•
To add a label to the list, select the Add New Label option in the Channel Labels
sub-menu.
Labels are allowed to be a maximum of eight characters, and the controls are the same as
editing.
The left (CH 1) encoder changes the currently selected character.
The right (CH 2) encoder changes the group.
There are three groups: capital letters (A-Z), numbers (0-9), and symbols (SYM).
• Press SELECT to change the selected character.
Joe’s C
Edit/Remove Labels
Joe’s C H
BACK
Edit/Remove
Labels
Add New Label
ADD......[A-Z]....BACK
Select
BACK
ADD......[A-Z]....BACK
Add
Joe’s CH added !
Joe’s CH added!
....................OK
OK
....................
Soft Button Labels
The Soft Button Labels menu option in the Advanced Settings sub-menu provides a way to
change the soft (programmable) talk buttons.
42
SIG:
BATT:
CAMERA 1
DIRECTOR
BATT:
SIG:
WTA 1&2
Soft (Programmable)
Button 1 Label
SA
Soft (Programmable)
Button 2 Label
There are five options:
Intercom Channels (CH) 1 & 2
Wireless-Talk-Around (WTA) 1
Wireless-Talk-Around (WTA) 2
Wireless-Talk-Around (WTA) 1 & 2
Stage Announce (SA)
•
To change one of the buttons, press SELECT on the Soft Button Labels menu option.
The screen will appear as follows:
SA
SAVE
BACK
WTA 1&2
SAVE
•
•
•
•
SA
BACK
Use either encoder to scroll and find the desired option.
To change the right soft button, press SELECT and the right button label will be
boxed.
Use either encoder to change the label.
When done, press SAVE to save the changes or BACK to ignore them.
Rx Volume Options
There are two options for the way the receiver volumes are controlled: Independent and
Master.
If Independent is selected, then the two receiver’s volumes are controlled independently.
At the home screen, the left encoder would control receiver 1 and the right would control
receiver 2.
If Master is selected, then both encoders control the receiver’s volumes. With Master
selected, one receiver will be a ratio of the other (“x” amount of dB higher or lower than the
43
Up
ow
ow
Soft Button Labels
Rx.Volume:
SAVE
BACK
Soft Button Labels
Independent
BACK
Soft Button Labels
Rx Volume: Independent
BACK
Up
other), and turning either encoder will change the volumes appropriately to keep the ratio the
same.
See the PC Application section for more information on the different ratios available.
Select
Soft Button Labels
Rx.Volume: Independent
SAVE
BACK
Rx Volume is located under the Advanced Settings sub-menu below Soft Button Labels as
shown above.
• To change the setting, press SELECT
• Turn the encoder until the desired option appears
• Press SAVE.
Headset Options
Up
ow
Rx.Volume:..Independent
Headset :
............
Combined
BACK
ow
Rx.Volume:..Independent
............Combined
BACK
Up
There are two local headset options: Combined or Separate.
This setting controls where the receiver audio gets routed, to the left and/or right
earphone.
If Separate is selected, audio for receiver 1 will be routed to the right earphone and audio
for receiver 2 will be routed to the left earphone.
If Combined is chosen, audio for both receivers will be routed to both earphones.
Note: if only one receiver is enabled then audio to that receiver will be routed to both
earphones no matter what headset option is chosen.
Rx.Volume:..Independent
Headset..:
SAVE
BACK
Select
Rx.Volume:..Independent
Headset..: Combined
SAVE
BACK
The headset setting is located under the Advanced Settings sub-menu right below Rx
Volume as shown above.
• To change the setting, press SELECT
• Turn the encoder until the desired option appears
• Press SAVE.
44
Info Screen
The Info screen displays a version number and serial number of the belt pack.
The version number is a composite firmware version number of all the firmware running in
the belt pack.
VER: XX.XXX
SN: XXXXXXXX
Headset..:..Combined
BACK
BACK
Headset..:..Combined
Info
BACK
Select
VER: XX.XXX
SN: XXXXXXXX
BACK
The Info screen is located under the Advanced Settings sub-menu right below Headset.
• To view the screen, press SELECT as shown above.
Enabling/Disabling the Passcode
Up
ow
Info
Passcode : Disabled
............
BACK
ow
Info
............Disabled
BACK
Up
The Advanced Settings sub-menu can be passcode protected.
The passcode is a four digit decimal number (0 – 9).
Info
Passcode.:
SAVE
Select
BACK
Info
Passcode.:
SAVE
Disabled
BACK
The passcode can be enabled or disabled from the Passcode screen.
It is located right below the Info screen in the Advanced Settings sub-menu as shown
above.
• To change the setting, press SELECT,
• Turn the encoder until the desired option appears
• Press SAVE.
Changing the Passcode
The passcode can be changed by selecting Change Passcode in the Advanced Settings submenu.
• Select Change Passcode
• enter the desired new passcode (pressing SELECT to advance to the next digit),
• press SAVE
• re-enter the desired new passcode
• press SAVE once finished.
45
If the two passcodes that were just entered match, then the passcode will be changed to
that value.
If they don’t match, then the passcode will remain unchanged.
..Enter.New.Passcode:
Passcode.:..Disabled
...........
BACK
Passcode.:..Disabled
Change Passcode
...........
BACK
Re-enter.New.Passcode:
...
*..Enter
*..*...
*New.Passcode:
.Re
*..-*enter
..*..*.New.Passcode:
SAVE..............BACK
SAVE..............BACK
.*..*..*..*
Select
Save
SAVE..............BACK
.*..*..*..*
SAVE..............BACK
Save
Save
ERROR:.Passcodes.don’t
.......match.
BACK
Passcode.changed.
BACK
Passcode
.changed.
BACK
ERROR:.Passcodes.don’t
.......match.
BACK
Microphone Gain
The local headset microphone gain can be changed in the menu.
• From the home screen press the menu button to get to the menu.
The right soft key will show “Mic G.”
• Press it to change the microphone gain.
Advanced Settings
Exit

Mic G
Display Settings
Advanced Settings
Exit
Mic G

Timeout
Mic G
Mic Gain
Mic Gain
SAVE
BACK
SAVE
BACK
• Use either encoder to change the value.
The bar graphic as well as a number (1 – 11) will show the current value of the microphone
gain. The gain will change as the user changes it (it is ‘live’).
• Press SAVE to save the change, and BACK to ignore any changes and return to the
menu.
46
Source Exif Data: 
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Author                          : Dennis Haley
Create Date                     : 2013:12:09 12:38:46-08:00
Modify Date                     : 2013:12:09 12:38:58-08:00
Subject                         : 
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26
Metadata Date                   : 2013:12:09 12:38:58-08:00
Creator Tool                    : Acrobat PDFMaker 10.1 for Word
Document ID                     : uuid:d72e31e6-1f95-484b-acd1-a5b08e6e6bce
Instance ID                     : uuid:0e40f04f-e52d-4531-b0c4-5fd35b0615e8
Format                          : application/pdf
Title                           : TITLE GOES HERE
Description                     : 
Creator                         : Dennis Haley
Producer                        : Adobe PDF Library 10.0
Keywords                        : 
Source Modified                 : D:20131209203745
Company                         : Radio Design Group, Inc.
Page Layout                     : OneColumn
Page Count                      : 46
EXIF Metadata provided by EXIF.tools
FCC ID Filing: 2AA6F-UV-1GBP

Navigation menu