Ramtech Electronics W2-RDO-9X WES+916.5MHz Radio Module User Manual W2 RDO 9X Module Install Guide
Ramtech Electronics ltd WES+916.5MHz Radio Module W2 RDO 9X Module Install Guide
Contents
- 1. User Manual
- 2. Installation Guide
- 3. Installation Guide issue 2
Installation Guide issue 2
Issue: 2 FOR RAMTECH PRODUCTS ONLY Date: 06/10/2016
© Ramtech Electronics Ltd 2016 Page 1 of 4
W2-RDO-9X Module
Installation Guide (SEN)
Items Required:
Manufacturer
Part Number
Quantity
Description
Ramtech
W2-CTRL-BRD
1
WES+ Control Board
Ramtech
W2-RDO-9X
1
WES+ 9X Radio Board
Essentra
MDLSP2-06M-01
2
6mm Dual Locking Support Post
Ramtech
W2-SEN-BASE
1
Sensor Product Base
Ramtech
W2-SEN-LID
1
Sensor Product Lid
TR Fastenings
W/N4/0.250/PRST
AB/TC1D
3
2.9x6.5 Pozi Pan Steel Screws
Insert support posts into the two
holes on the radio module until they
lock.
Locate the support posts and the
module connectors over the control
board.
Press firmly until the support posts
lock into place.
W2-RDO-9X Module Install Guide
© Ramtech Electronics Ltd 2016 Page 2 of 4
Lay out Product Base which should
already include:
Back Tamper Assembly
Battery Sticker
Battery Foam
Battery Straps
Battery
Line up the Control Board plus Radio
Module assembly with the three
screw holes in the product base.
Screw board assembly down.
Connect back tamper connector
(blue).
W2-RDO-9X Module Install Guide
© Ramtech Electronics Ltd 2016 Page 3 of 4
Lay out Sensor Lid which should
already include:
Antenna
Ground Plane
Sensor Base
Membrane
Line up the Sensor Lid over the Sensor
Base and connect:
1. Membrane Connector
2. Antenna
3. Sensor Connector
4. Battery
Close the Lid.
1
2
3
4
W2-RDO-9X Module Install Guide
© Ramtech Electronics Ltd 2016 Page 4 of 4
Host product must be labelled with “Contains FCC ID: 2AHNOW2-RDO-9X and IC: 21246-W2RDO9X”.
This radio module is for mobile use and should not be used within 20cm of the human body when
the RF is enabled.
FCC Warning Statement – FCC ID: 2AHNOW2-RDO-9X
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may
cause undesired operation.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. End users must follow the specific operating instructions for satisfying RF
exposure compliance. This transmitter must not be co-located or operating in conjunction
with any other antenna or transmitter.
Changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment
Industry Canada Warning Statement – IC ID: 21246-W2RDO9X
English
Under Industry Canada regulations, this radio transmitter may only operate using an
antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry
Canada. To reduce potential radio interference to other users, the antenna type and its gain
should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more
than that necessary for successful communication.
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is
subject to the following two conditions:
1. This device may not cause interference, and
2. This device must accept any interference, including interference that may cause
undesired operation of the device.
French
Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut
fonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour
l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage
radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son
gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas
l'intensité nécessaire à l'établissement d'une communication satisfaisante.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio
exempts de licence. L'exploitation est autorisée aux deux conditions suivantes:
1. l'appareil ne doit pas produire de brouillage, et
2. l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d'en compromettre le fonctionnement.