Ramtech Electronics W2-RDO-9X WES+916.5MHz Radio Module User Manual W2 RDO 9X Module Install Guide

Download:
Mirror Download [FCC.gov]
Document ID	3238274
Application ID	JWKtFA10eBWW4eNbm2K4yg==
Document Description	Installation Guide issue 2
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	54.39kB (679859 bits)
Date Submitted	2016-12-23 00:00:00
Date Available	2016-12-23 00:00:00
Creation Date	2016-11-25 08:19:01
Producing Software	Microsoft® Word 2016
Document Lastmod	2016-11-25 08:19:01
Document Title	W2-RDO-9X Module Install Guide
Document Creator	Microsoft® Word 2016
Document Author:	Steven Richardson

Issue: 2
FOR RAMTECH PRODUCTS ONLY
Date: 06/10/2016
W2-RDO-9X Module
Installation Guide (SEN)
Items Required:
Manufacturer
Part Number
Quantity
Description
Ramtech
W2-CTRL-BRD
WES+ Control Board
Ramtech
W2-RDO-9X
WES+ 9X Radio Board
Essentra
MDLSP2-06M-01
6mm Dual Locking Support Post
Ramtech
W2-SEN-BASE
Sensor Product Base
Ramtech
W2-SEN-LID
Sensor Product Lid
TR Fastenings
W/N4/0.250/PRST
AB/TC1D
2.9x6.5 Pozi Pan Steel Screws
Insert support posts into the two
holes on the radio module until they
lock.
Locate the support posts and the
module connectors over the control
board.
Press firmly until the support posts
lock into place.
© Ramtech Electronics Ltd 2016
Page 1 of 4
W2-RDO-9X Module Install Guide
Lay out Product Base which should
already include:





Back Tamper Assembly
Battery Sticker
Battery Foam
Battery Straps
Battery
Line up the Control Board plus Radio
Module assembly with the three
screw holes in the product base.
Screw board assembly down.
Connect back tamper connector
(blue).
© Ramtech Electronics Ltd 2016
Page 2 of 4
W2-RDO-9X Module Install Guide
Lay out Sensor Lid which should
already include:




Antenna
Ground Plane
Sensor Base
Membrane
Line up the Sensor Lid over the Sensor
Base and connect:
1.
2.
3.
4.
© Ramtech Electronics Ltd 2016
Membrane Connector
Antenna
Sensor Connector
Battery
Close the Lid.
Page 3 of 4
W2-RDO-9X Module Install Guide
Host product must be labelled with “Contains FCC ID: 2AHNOW2-RDO-9X and IC: 21246-W2RDO9X”.
This radio module is for mobile use and should not be used within 20cm of the human body when
the RF is enabled.
FCC Warning Statement – FCC ID: 2AHNOW2-RDO-9X

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may
cause undesired operation.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. End users must follow the specific operating instructions for satisfying RF
exposure compliance. This transmitter must not be co-located or operating in conjunction
with any other antenna or transmitter.

Changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment
Industry Canada Warning Statement – IC ID: 21246-W2RDO9X
English
 Under Industry Canada regulations, this radio transmitter may only operate using an
antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry
Canada. To reduce potential radio interference to other users, the antenna type and its gain
should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more
than that necessary for successful communication.

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is
subject to the following two conditions:
1. This device may not cause interference, and
2. This device must accept any interference, including interference that may cause
undesired operation of the device.
French
 Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut
fonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour
l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage
radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son
gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas
l'intensité nécessaire à l'établissement d'une communication satisfaisante.

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio
exempts de licence. L'exploitation est autorisée aux deux conditions suivantes:
1. l'appareil ne doit pas produire de brouillage, et
2. l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d'en compromettre le fonctionnement.
© Ramtech Electronics Ltd 2016
Page 4 of 4

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 4
Language                        : en-US
Tagged PDF                      : Yes
XMP Toolkit                     : 3.1-701
Producer                        : Microsoft® Word 2016
Title                           : W2-RDO-9X Module Install Guide
Creator                         : Steven Richardson
Creator Tool                    : Microsoft® Word 2016
Create Date                     : 2016:11:25 08:19:01+00:00
Modify Date                     : 2016:11:25 08:19:01+00:00
Document ID                     : uuid:EE58D9E3-730C-418D-9E3E-B37AAF209E4D
Instance ID                     : uuid:EE58D9E3-730C-418D-9E3E-B37AAF209E4D
Author                          : Steven Richardson

EXIF Metadata provided by EXIF.tools