Raritan Engineering Seaera Toilets Users Manual L318

SeaEra Toilets L318seaerav0103

SeaEra Toilets to the manual 6d90a1b1-5c5a-4f81-a03d-69a30a5ca4ed

: Raritan-Engineering Raritan-Engineering-Seaera-Toilets-Users-Manual-502323 raritan-engineering-seaera-toilets-users-manual-502323 raritan-engineering pdf

Open the PDF directly: View PDF .
Page Count: 16

Pressurized

Freshwater Model Sea Water Model

(Remote Pump) Sea Water Model

(Integral Pump)

The SeaEra toilet is a powerful centrifugal macerating toilet that thoroughly breaks down waste.

SeaEra Toilet

OPERATION, MAINTENANCE AND INSTALLATION INSTRUCTIONS

THE FOLLOWING ARE CAUTIONARY STATEMENTS THAT MUST BE READ AND

FOLLOWED DURING BOTH INSTALLATION AND OPERATION.

WARNING: Raritan Engineering Company, Inc. recommends that a qualified person or electrician install this

product. Equipment damage, injury to personnel or death could result from improper installation.

Raritan Engineering Company, Inc. accepts no responsibility or liability for damage to equipment,

injury or death to personnel that may result from improper installation or operation of this product.

WARNING: HAZARD OF SHOCK OR FIRE

Always use recommended fuse, circuit breaker and wire size.

Motors used with this product are “Ignition Protected”. They are not however, explosion-

proof as defined in 46CFR 110.15-65(e), Subchapter J-Electrical Engineering.

DO NOT run continuously for more than 30 seconds.

WARNING: HAZARD OF FLOODING - Always shut off seacock(s) before leaving the boat unattended.

Double clamp all below waterline hose fittings and check frequently for integrity.

1-800-352-5630

www.raritaneng. com

Press push-button switch and hold until all

waste is cleared from the toilet bowl.

• No special toilet paper is required.

• Water should appear in the bowl within ten

seconds. If not, see troubleshooting section.

• Hard objects or stringy substances (paper

towels, feminine hygiene products, filter

cigarettes, etc.) must not be thrown into the

toilet as they will cause damage.

• Always shut off seacock(s) before leaving the

boat unattended.

OPERATION

2

Young children should NOT be left unsupervised

around toilet. Serious injury or death could occur.

WARNING: DO NOT place hands in toilet

bowl without disconnecting

power. A sharp blade is used for

maceration of waste.

We offer an optional “child safety switch” which is

designed to make it difficult for young children to

operate toilet without adult supervision. For more

information, contact Raritan Technical Support

(1-800-352-5630).

WARNING: Children can drown in water

retained in the bowl.

CAUTION: Seat and/or lid could close and

strike child.

Clean Gasket

and Gasket

Contact Surfaces

Thoroughly

Unscrew Tighten

Cleaning Instructions

IMPORTANT: Do not use cleaners that contain

ammonia, ethyl acetate, phosphoric acid or

concentrated chlorine bleach. These may cause

damage to the toilet.

Using C.P. a bio-enzymatic toilet bowl cleaner

(available from Raritan Engineering) will keep the

bowl clean and fresh smelling.

Recommend Visual Inspection

✔For leaks at toilet and hose connections

✔Hose clamps

✔Condition of hoses

✔Seacocks

✔Condition of wires and connections

✔In-Line Strainer (if you have one)

Cleaning In-Line Strainer

(Sea Water Models only)

1. Shut off intake seacock.

2. Unscrew bowl.

3. Remove filter.

4. Clean bowl and filter with a clean cloth.

5. Clean gasket and gasket contact surfaces

thoroughly.

6. Replace gasket, filter and bowl.

7. Open seacock.

8. Check for leaks.

MAINTENANCE

3

C.P.

Bowl

Filter

WINTERIZING

IMPORTANT

• Improper winter lay up is a major cause of

marine toilet failure.

• Use only nontoxic antifreeze.

• Flush toilet several times to clear waste

from system.

• Dispose of all antifreeze in accordance with

local and federal regulations.

• Winterize holding tanks, plumbing,

treatment systems (MSD’s), etc.

independently following manufacturer’s

instructions.

Pressurized Freshwater Models

Parts Required

• 1" (25mm) or 1 1/2" (38mm) I.D.discharge

hose, approximately 3 feet (1m) long

• Two buckets

• Nontoxic antifreeze approximately 1 quart

(1 liter)

Steps

1. Close discharge seacock.

2. Shut off intake water at source.

3. Turn off power to unit.

4. Disconnect and drain discharge hose.

5. Disconnect intake hoses from vacuum breaker

and place in one of the buckets.

6. Connect hose to toilet’s discharge and place

in other bucket.

7. Pour antifreeze in bowl.

8. Turn on power to unit and flush until antifreeze

is removed from the bowl and water is drained

from the solenoid and hose.

9. Disconnect power to toilet.

10. Reconnect intake hoses to vacuum breaker.

4

Pressurized Freshwater Model

Nontoxic

Antifreeze

Integral and Remote Intake Pump Models

Parts Required

3/4" (19mm) I.D. intake hose approximately 3 feet

(1m) long.

1" (25mm) or 1 1/2" (38mm) I.D. discharge hose

approximately 3 feet (1m) long.

Two buckets

Nontoxic antifreeze approximately 1 quart (1 liter)

Steps

1. Close the intake and discharge seacocks.

2. Turn off power to unit.

3. Disconnect and drain intake hose, discharge hose

and In-Line Strainer.

4. Connect short hoses to toilet’s intake and

discharge.

5. Place one bucket under hose connected to toilet’s

discharge.

6. Pour nontoxic antifreeze in other bucket.

7. Place hose connected to intake pump into bucket

with antifreeze.

8. Turn on power to unit and flush toilet until

antifreeze begins to be discharged from toilet.

9. Disconnect power to toilet.

RECOMMISSIONING

1. Using the buckets, hoses and approximately one

gallon (3.8 liters) of clean fresh water, flush

antifreeze out of the toilet (see Winterizing).

Dispose of antifreeze in accordance with local

and federal regulations.

2. Reconnect the intake and discharge hoses and

open both seacocks and water source valve.

3. Check all connections for leaks with several test

flushes.

SYSTEM START-UP

1. Open seacock(s).

NOTE: Pressurized freshwater models; open water

source valve.

2. Turn on power to toilet.

3. Flush toilet per Operation Instructions.

4. Check for leaks.

IMPORTANT: If toilet does not flush properly

or if water does not enter the bowl within 10

seconds, refer to Troubleshooting.

Nontoxic

Antifreeze

Sea Water Model (Integral Pump)

Sea Water Model (Remote Pump)

Nontoxic

Antifreeze

WINTERIZING

5

SPECIFICATIONS

Pressurized Freshwater Model - Recommended Wire and Fuse/Circuit Breaker Size

6 5/8" (16.8cm)

19 3/4" (52.1cm) Household

17 1/2" (44.5cm) Marine 14 3/8" (36.5cm) Household

13" (33cm) Marine

11 1/8" (28.3cm)

14 7/8"

(37.8cm)

Household

14 1/2"

(36.8cm)

Marine

14 7/8"

(37.8cm)

Household

14 1/2"

(36.8cm)

Marine

19 3/4"(50.2cm) Household

16 3/4"(42.6cm) Marine

13 3/8" (34cm)

Pressurized Freshwater or Remote Sea Water Model Integral Sea Water Model

6

Sea Water Model - Recommended Wire and Fuse/Circuit Breaker Size

Plumbing

CONVERSIONS

Wire - AWG to mm2

Feet to Meters

NOTES: for Wiring

teeF 01510252030405

reteM 1.36.41.66.72.92.212.51

GWA 614121018642

mm

2

5.15.20.40.60.010.610.520.53

pmupekatnIfonoitcusmumixaM )enilretawevobathgiehmumixaM( .pmuPekatnImorf)m2.1(.tF4

pooldetnevegrahcsidfothgiehmumixaM .teliotfoesabmorf)m8.1(.tF6

stnemeriuqerecruosretawdezirusserP .)sretil3.11(mpg3foetarwolfmuminim .)aPk5.43(isp5foerusserpmuminim

.1 .ecruosotkcabdnatinuotecruosmorferasecnatsiD

.2 nehwdedulcniebTSUMpmupekatnietomerotecruosrewopmorfecnatsiD dnaesabrewolrofdesuebTSUMeziseriwemaS.ecnatsidlatotgninimreted .pmupekatnietomer

.3 mm(GWAmuminimeriwrotcudnocdednemmoceR

2

.pordegatlov%3rof)

.4 501nodesaberasezisrotcudnocdednemmoceR

o

.noitalusnidetarC.sgnitarnoitalusnirehtorofsdradnatSCYBAotrefeR

.5 .tinuotremrofsnartmorfsnoitacificepsCDV42esustinuCAV042/021roF

stinU egatloV

tiucriC esuf/rekaerB )spma(ezis

pmuPlargetnI esabrewoldna

ward.pmA lanimon@ egatlov

pmuPetomeR esabrewoldna

ward.pmA lanimon@ egatlov

pmuPetomeR ylno

ward.pmA lanimon@ egatlov

51 teef 02 teef 03 teef 04 teef 05 teef

CDV2152813201GWA01GWA8GWA6GWA6GWA4

CDV4251015.215

GWA41GWA41GWA21GWA01GWA01

CDV23515.794

GWA41GWA41GWA41GWA21GWA21

stinU egatloV

tiucriC esuf/rekaerB )spma(ezis

ward.pmA lanimon@ egatlov

teef01teef51teef02teef03teef04teef05

CDV21 esaBrewoL 5231GWA21GWA01GWA01GWA8GWA6GWA6

CDV42 esaBrewoL 515.7 GWA41GWA21GWA01GWA01GWA8GWA6

CDV23 esaBrewoL 515

GWA61GWA61GWA41GWA21GWA01GWA01

CDV23dna,42,21 dioneloSretaW evlaV 32

GWA61GWA61GWA61GWA61GWA61GWA61

7

Mounting Toilet

Mounting surface must be flat and solid.

1. Install seat on toilet.

2. Remove motor cover.

3. Place toilet where it will be located.

Make sure there is room to route hoses.

Make sure seat will open properly.

4. Mark location of toilet base mounting holes

on mounting surface.

5. Drill holes for toilet mounting bolts/screws.

NOTE: Hole size will depend on type of bolt/

screws used (5/16" [8mm] size bolts/screws are

recommended).

6. Secure toilet to surface.

INSTALLATION

Additional Parts Required

• Four stainless steel mounting bolts or lag

screws (minimum 1/4" [6mm]) and washers

• 1" (25mm) or 1 1/2" (38mm) I.D. discharge hose

• 3/4" (19mm) I.D. reinforced intake hose

• 3/4" (19mm) and 1" (25mm) or 1 1/2" (38mm)

hose clamps (two for each connection below

waterline)

• Wire

• Terminals

• Fuse/circuit breaker

Parts Included

All Complete Toilets

Toilet Bowl

Seat and Cover

Lower Base Assembly

Motor Cover

Push Button Switch

Sea Water Model

3/4" Hose Barb - straight fitting (2)

3/4" Hose Barb - 90° fitting

Plug Fitting

In-Line Strainer with fittings

3/4" Stainless Steel Hose Clamps (2)

Pressurized Freshwater Models

Atmospheric Vacuum Breaker (PLAVB0-5)

Solenoid Valve with fittings

Solenoid Valve Mounting Bracket

Tools Required

• 5/16" nut driver

• Wrench or screw driver

• 5/8" (16mm) drill bit

• Bit for drilling mounting surface

• Wire cutters

• Wire terminal crimpers

• Hose cutters

• Tape measure

8

90° Rotation of Toilet Bowl

Toilet bowl can be rotated 90° on the base, for

installing in confined locations.

NOTE: SeaEra Models with Integral Pump:

Replace existing hose from the intake pump to the

toilet bowl with a longer hose.

1. Determine which direction bowl is to be

mounted.

2. Remove hose at back of toilet (Sea Water

Model with Integral Pumps ONLY).

3. Remove four vinyl caps at the base of toilet

bowl.

4. Remove four nuts and shoulder washers.

5. Carefully remove toilet bowl from base.

6. Rotate toilet bowl to desired position.

7. Replace four shoulder washers, nuts and vinyl

caps.

NOTE: Tighten nuts carefully and evenly. Do

Not over tighten.

Mounting Push Button Switch

• Mount Push Button Switch in an accessible

location.

• Make certain wires can be routed to Push

Button Switch.

• Wire terminals must have clearance when

installed.

1. Drill 5/8" (16mm) hole.

2. Attach wires to Push Button Switch terminals

(see wiring section).

3. Install Push Button Switch through back of

mounting surface.

4. Install waterproof nut on Push Button Switch.

5. Secure in place with inner nut.

Install the Warning Label (L322) where it can

be easily seen.

INSTALLATION

1/4" Minimum clearance from terminals to any object

Inner Nut

INSTALLATION

Mounting Water Solenoid Valve

(Pressurized Freshwater Models Only)

1. Locate valve on a solid flat surface in an area

that is dry and well ventilated.

2. Mark and drill holes for water solenoid mounting

bracket.

NOTE: Hole size will depend on type of bolts/screws

used (1/4" [6mm] size bolt/screws are recommended).

3. Mount bracket.

4. Install fittings provided (PLA7) on valve’s inlet

and outlet ports.

5. Attach valve to bracket. hoses must be installed

according to flow markings on valve body.

Mounting Atmospheric Vacuum Breaker

(Pressurized Freshwater Model only)

1. Install fittings as shown.

2. Locate mounting area that is a minimum of 6"

(15.3cm) above toilet.

3. Secure where top is in horizontal position.

Mounting In-Line Strainer

(Seawater Models Only)

Make sure strainer bowl is tight.

1. Locate strainer where it will be accessible.

2. Mark and drill mounting holes.

NOTE: Hole size will depend on type of bolts/screws

used (1/4" [6mm] size bolts/screws are

recommended).

3. Install fittings provided (PLA7) on strainer’s inlet

and outlet ports.

NOTE: Use thread sealant.

4. Mount strainer. Hoses must be installed according

to flow marking on strainer top.

Mounting Remote Intake Pump

(Remote Pump Models Only)

1. Remote intake pump must be mounted on a

flat solid surface in an area that is dry and well

ventilated.

2. Mark and drill mounting holes.

NOTE: Hole size will depend on type of bolts/screws

used. (1/4" [6mm] size bolts/screws are

recommended).

3. Mount pump. Do not over tighten bolts.

9

Flow Marking

From

Pressurized

Freshwater

Source

OUT

PLA7

To inlet port of

vacuum breaker

IN

Min. 6”

(15.3 cm)

10

INSTALLATION

Discharge Lines

1. Connect quality sanitation hose 1"

(25mm) or 1 1/2" (38mm) I.D. to

discharge fitting on toilet.

2. Run hose to appropriate device (i.e.:

treatment system, holding tank, etc.).

PLUMBING

WARNING: Hazard of Flooding

Toilets mounted at or below the waterline

must have a vented loop installed in the

discharge line. The top of the vented loop

must be a minimum of 4" (10cm) above

the waterline at the boats greatest angle

of heel (see vented loop manufacturer’s

instructions).

Sea Water Models must also have a vented

loop installed between the intake pump

and the toilet bowl.

Double clamp all below waterline

connections.

IMPORTANT

• Fittings and 90° bends should be kept

to a minimum.

• In-Line Strainer must be installed on

Sea Water Models per Installation

Instructions. Failure to do so may void

Warranty.

• Discharging untreated sewage is

forbidden in all U. S. waters within the

three-mile limit.

• Thru-hull fittings and seacocks must

be installed where they are easily

accessible.

• Use only quality reinforced hoses.

• Secure all hoses properly.

Pressurized Freshwater Model

Installed Above Waterline

SeaEra

Toilet

Vacuum

Breaker

Water

Solenoid

Valve

Discharge

Holding Tank

Pressurized Freshwater

Source

Waterline

Shut off

Valve

Sea Water Model with Integral Pump

Installed Below Waterline

SeaEra

Toilet Waterline

Intake Vented

Loop

Intake

Seacock

Remote

Intake

Pump

In-Line

Strainer

Discharge

Seacock

Discharge

Vented

Loop

Intake

Seacock

Holding Tank

SeaEra Toilet

Y Valve

In-Line

Strainer

Lectra/San

Waterline

Waterline

Waterline

Remote Intake Pump Model

Mounted Above Waterline

Discharge

Seacock

Waterline

Discharge

Vented

Loop

Lectra/San

1 1/2" (38mm)

Discharge Fitting

1" (25mm)

Discharge Fitting

Hose

11

From

Seacock

To Intake

Pump

INSTALLATION

Intake Lines

Pressurized Freshwater Models

Install a shut off valve in intake line before water

solenoid valve.

1. Connect hose from shut off valve to inlet port

of water solenoid valve.

NOTE: To avoid malfunction of water solenoid due

to debris in water, installation of Freshwater

Strainer (190601) is recommended.

2. Connect hose from outlet port of water solenoid

valve to inlet port of vacuum breaker.

3. Connect hose from outlet port of vacuum breaker

to bowl elbow.

NOTE: Vacuum breaker must be last mechanical

component before bowl elbow.

Sea Water Models

Intake pump fittings are interchangeable to allow

more flexibility during installation. Inlet ports are

located on either side of intake pump. Outlet port

(to toilet bowl) is at top of intake pump.

1. Slide fitting clips to open position.

2. Select inlet port to be used.

3. Install appropriate fittings into inlet and outlet

ports.

NOTE: The 90° fitting can be rotated 360°.

4. Install the plug fitting into unused inlet port.

IMPORTANT: Be sure not to install plug fitting

into outlet port! Damage will occur!

5. Slide fitting clips back to closed position.

6. Connect hose from seacock to inlet port of

In-Line Strainer. Use hose clamp provided.

7. Connect hose from outlet port of In-Line

Strainer to inlet port of intake pump. Use hose

clamp provided.

IMPORTANT: Double clamp all below

waterline hose connections!

8. Remote Pump Models Only: Connect hose

from outlet port of intake pump to bowl elbow

located on back of toilet bowl. (Integral pump

model is already connected).

From Pressurized

Freshwater Source

(Shut Off Valve)

To Inlet Port

of Vacuum

Breaker

Inlet Ports

Outlet Port

Arrow

OUT

IN

Open Closed

Plug

From Strainer

To Bowl

Outlet Port

Inlet Port

WIRING

WARNING: Hazard of Shock and Fire

• Always use proper wire, wire connectors

and fuse/circuit breaker. See Specification

Chart.

• Secure wire properly.

• Do not connect appliances to toilet circuit.

• Make sure power is off before proceeding.

• Use proper wire terminals for all wire

connections.

1. Determine proper wire size by measuring

distance from:

• Power Source to push-button to toilet

motor and back to power source.

• Remote pump units - also include distance

from power source for remote pump to

remote pump and back. Same wire must

be used for both lower base and remote

pump.

2. Select proper wire and fuse/circuit breaker size

from Specifications on Installation page.

3. Install fuse/circuit breaker in positive line at

source.

4. Connect positive wire from fuse/circuit

breaker to Push Button Switch.

5. Connect wire from Push Button Switch to

orange wire on motor(s).

NOTE: Pressurized Freshwater Models; connect

wire from Push Button Switch to orange wire on

motor and from Push Button Switch to one of the

wires on water solenoid valve. The water solenoid

valve is not polarity sensitive.

6. Connect wire from battery negative or power

source ground buss to black wire (negative)

on motor(s).

NOTE: Pressurized Freshwater Models; connect

remaining wire from water solenoid valve to

battery negative or power source ground buss.

WIRING

12

Orange

POS (+)

Fuse or

Circuit

Breaker

Push Button

Switch

Black

NEG (-)

Fuse or

Circuit

Breaker

Orange

POS (+)

Black

NEG (-)

POSNEG

POSNEG

Integral Pump Wiring

Remote Pump Wiring

Push Button

Switch

Fuse or

Circuit

Breaker

Orange

POS (+)

POSNEG

Pressurized Freshwater Wiring

Push Button

Switch

Black

NEG (-)

Black

NEG (-)

Solenoid

Valve

3 Amp

Fuse

TROUBLESHOOTING

WARNING: HAZARD OF ELECTRIC SHOCK - Before beginning any work on the SeaEra, be sure that all

power to the unit has been turned off.

WARNING: HAZARD OF FLOODING - Make sure seacocks are in the CLOSED or OFF position before

working on toilet.

NOTE: The following information reflects the most probable causes and solutions to problems although not

every possible cause and solution is provided.

Any questions regarding servicing or operation of the SeaEra should be directed to our Technical Support Department in

Millville, NJ or Ft. Lauderdale, FL. Please have model and serial number available before calling.

TROUBLESHOOTING

13

PROBLEM

1. Poor pumpout, especially

solids.

2. Poor water flow, especially

at front of bowl (or no wa-

ter flow).

3. Foul odors from toilet area.

4. Bowl fills while underway.

5. Water leaking from under

unit.

6. Erratic operation/sluggish

running.

POSSIBLE CAUSE

1A. Clogged discharge line.

1B. Plumbing restrictions, bends and ells.

1C. Clogged vents.

1D. Mineral buildup in hoses and fittings.

1E. Low voltage.

2A. Toilet not level.

2B. Restriction in intake line.

2C. Pump sucking air.

2D. Low voltage.

2E. Clogged strainer.

3A. “Marine life” lodged in rim of bowl.

3B. Permeated discharge hose.

3C. Sewage remaining in discharge line.

4A. Pressure buildup at seacocks.

5A. Leaking bowl gasket.

5B. Leak at shaft seal.

5C. Leak from seal plate area.

6A. Worn motor brushes.

6B. Motor bearings damaged by seal leak.

6C. Low or inconsistent voltage.

SOLUTION

1A. Be sure discharge seacock is open. Clear line, remove

clog.

1B. Replumb to eliminate bends and ells.

1C. Clean holding tank vent and vented loop vents

1D. Clean or replace affected parts. Replace hose if needed.

1E. Check voltage at toilet while toilet is running. If

less than nominal voltage of toilet (12, 24, or 32),

check condition of batteries and wire sizes. Check

terminals and wire connections for corrosion (heat at

terminals and junctions indicates a bad or corroded

connection).

2A. Raise rear of toilet; check with level.

2B. Be sure seacock is open. Clear line-remove clog.

2C. Check all connections from intake thru-hull to intake

pump to be sure no air leaks are present.

2D. See 1E, above.

2E. Remove or Clear debris from strainer.

3A. Remove and flush bowl with pressure hose to remove

all material. Install strainer in intake line to avoid re-

currence.

3B. Replace hose with Raritan sanitation hose (#SH).

3C. Flush toilet longer; replace hose if permeated; reroute

hose making a shorter run if possible.

4A. Close intake, then discharge seacock to determine

which is causing problem. If discharge, be sure the

vent or vented loop is clean. If intake, there is too

much pressure on seacock; contact Raritan Technical

Support.

5A. Tighten (4) bowl mounting nuts (#1226B).

5B. Check seal and motor shaft.

5C. Check seal plate o-ring.

6A. Return motor to factory for servicing or replacement.

6B. Return motor to factory for servicing or replacement.

6C. See 1E above.

Set screw must be loosened

with 1/8" hex key before

removing the intake pump

from motor

Tip for Removing Intake Pump

Plug

EXPLODED PARTS

Part No. Description

1108A Macerator Nut

1222AW 90° Discharge Fitting

1226 Mounting Screw (4)

1226B 1/4-20 Hex Nut (4)

1234 Bowl Gasket

1236AW Bowl Spud Assembly

1236E Bowl Elbow

1237 Marine-size Bowl

1244 Household-style Bowl

1610* Motor

161105 Base

161107 Seal Plate O-Ring

161110 Seal Plate

161115 Impeller

161120 Impeller/Macerator Housing

161123 Macerator Blade

161125 Discharge Mounting Flange

161130 Discharge Fitting

162135 Cone Seal

162225 O-Ring

162305 Lower Housing includes #162315

162310 Diaphragm includes #162315

162315 Piston (4)

162320 Piston Seat (4) includes #162315

162325A Bearing Plate Assembly includes

#162315

162405 3/4" Hose Barb - 90° Fitting

162410 3/4" Hose Barb - Straight Fitting (2)

162415 Plug Fitting

162420 Fitting Clip (3)

162425 Fitting O-Ring (4)

SeaEra PARTS LIST

Part No. Description

162100W Upper Housing Assembly

162200W Middle Housing Assembly

162300W Lower Housing Assembly

163000 Inline Strainer

164000 Push Button Switch

31-102 Shaft Seal

41-260 Bowl Elbow (Freshwater Models Only)

C254 Joker Valve

CH38 1/4-20 Threaded Stud (4)

F005 Set Screw

F020 Piston Fastener (4)

F144 Mounting Bolt Washer (4)

F162VT Mounting Bolt

F164 Discharge Mounting Flange Fastener(4)

HW1 Mounting Screw Lockwasher (4)

M23A Macerator Lockwasher (5)

Additional Parts Included with

INTEGRAL MODELS

161140 Motor Cover Integral

Additional Parts Included with

REMOTE MODELS

161135 Motor Cover

1660* Intake Motor

166000 Remote Intake Pump, 12V DC

166100 Remote Intake Pump, 24V DC

166200 Remote Intake Pump, 32V DC

Additional Parts Included with

FRESHWATER MODELS

161135 Motor Cover

PLAVB0-5 Atmospheric Vacuum Breaker

PLA5 1/2” MPT PVC Nipple

PLA6 1/2” FPT to 3/4” Barbed Elbow

PLA7 1/2” GC Solenoid Valve

CWPS*A 1/2” GC Solenoid Valve

CWPSMB Water Solenoid Valve Mounting Bracket

Repair Kits

DIAPUMPRK Diaphragm Pump Repair Kit

SEADISRK SeaEra Discharge Repair Kit

* Specify DC Voltage (12, 24, 32)

14

15

EXPLODED PARTS

SeaEra Exploded Parts View

1244 or 1237

1236AW

1236E

1234

VCAP

1226B

RNI

CH38

161105

C254

161130

1222AW

161125

F164

161107

1108A

M23A

161123

161120

16111531-102

161110

1610*

HW1

1226

161135 or 161140

164000

F020

F005

162325A

162305

162320

162310

162315

162420

162405

162415

162410

162425

F144

F162VT

163000

1660*

M23A

162300W

162425

162425

162225

162135

162100W

162420

162200W

ATMOSPHERIC

VACUUM BREAKER

PLA6 PLAVB0-5

PLA7

SOLENOID VALVE

CWPS*A

PLA7

PLA7

CWPSMB

PLA5

190601 - Recommended for use with

Freshwater Solenoid (Not Included)

L318 0103kgs Specifications Subject to Change Without Notice Printed in U.S.A.

530 Orange Street, P.O. Box 1157, Millville, NJ 08332 USA

Telephone: 856-825-4900 FAX: 856-825-4409

www.raritaneng.com

Southern Office and Plant:

3101 SW Second Avenue, Fort Lauderdale, FL 33315 USA

Telephone: 954-525-0378 FAX: 954-764-4370

LIMITED WARRANTY

Raritan Engineering Company warrants to the original purchaser that this product is free of defects

in materials or workmanship for a period of one year from the product’s date of purchase. Should

this product prove defective by reason of improper workmanship and/or materials within the

warranty period, Raritan shall, at its sole option, repair or replace the product.

1. TO OBTAIN WARRANTY SERVICE, Consumer must deliver the product prepaid, together with

a detailed description of the problem, to Raritan at 530 Orange St., Millville, N.J. 08332, or 3101 SW

2nd Ave. Ft. Lauderdale, FL 33315. When requesting warranty service, purchaser must present a

sales slip or other document which establishes proof of purchase. THE RETURN OF THE OWNER

REGISTRATION CARD IS NOT A CONDITION PRECEDENT OF WARRANTY COVERAGE.

However, please complete and return the owner Registration Card so that Raritan can contact you

should a question of safety arise which could affect you.

2. THIS WARRANTY DOES NOT COVER defects caused by modifications, alterations, repairs or

service of this product by anyone other than Raritan; defects in materials or workmanship supplied

by others in the process of installation of this product; defects caused by installation of this product

other than in accordance with the manufacturer’s recommended installation instructions or standard

industry procedures; physical abuse to, or misuse of, this product. This warranty also does not cover

damages to equipment caused by fire, flood, external water, excessive corrosion or Act of God.

3. ANY EXPRESS WARRANTY NOT PROVIDED HEREIN, AND ANY REMEDY FOR BREACH

OF CONTRACT WHICH BUT FOR THIS PROVISION MIGHT ARISE BY IMPLICATION OR

OPERATION OF LAW, IS HEREBY EXCLUDED AND DISCLAIMED. ALL IMPLIED

WARRANTIES SUCH AS THOSE OF MERCHANTABILITY AND OF FITNESS FOR A

PARTICULAR PURPOSE, IF APPLICABLE, AS WELL AS ANY IMPLIED WARRANTIES

WHICH MIGHT ARISE BY IMPLICATION OF LAW, ARE EXPRESSLY LIMITED TO A

TERM OF ONE YEAR. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG A

LIMITED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU.

4. UNDER NO CIRCUMSTANCES SHALL RARITAN BE LIABLE TO PURCHASER OR ANY

OTHER PERSONS FOR ANY SPECIAL OR CONSEQUENTIAL DAMAGES, WHETHER

ARISING OUT OF BREACH OF WARRANTY, BREACH OF CONTRACT, OR OTHERWISE.

SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR

CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT

APPLY TO YOU.

5. No other person or entity is authorized to make any express warranty, promise or affirmation of fact

or to assume any other liability on behalf of Raritan in connection with its products except as

specifically set forth in this warranty.

6. This warranty gives you specific legal rights, and you may also have other rights which vary from

state to state.

16