Rayrun Technology RM06 Remote Controller User Manual
Rayrun Technology Co., Ltd Remote Controller
User Manual
Introduction Wireless Synchronizing 4-CH LED Controller RQ211 / RQ212 User’s Manual Thank you for purchasing our products. RQ211 and RQ212 4ch RGBW LED controller is designed to drive constant voltage LED products with common anode connection in voltage range of DC6-24V. RQ211 is master unit controlled by a RF remote, RQ212 is slave unit synchronized with RQ211 wirelessly. User can program them to multi-zone group by the remote, and setup white or color lighting or synchronized dynamic modes in different zones. WHITE WHITE ONLY WHITE OFF COLOR COLOR Full Protection Waterproof Option RGBW 4-ch Output RF Remote Controller Wireless Sychronizing Ultra Slim Design Multi-Zone Control Easy Group Setting Functions COLOR MODE MODE SPEED SPEED All Zone ZONE ZONE ZONE 6. RGB Dynamic Modes Control 1. Turn On/ Standby Press ‘I’ key to turn on unit or press ‘O’ key to turn off. At power on moment, unit will automatically restore to previous status before power cut. These keys control the RGB dynamic modes. a) Press ‘MODE+’ and ‘MODE-’ key to select preset dynamic modes. b) Press ‘SPEED+’ and ‘SPEED-’ to control the dynamic mode running speed. 7. Zone Control 2. White Mode These two keys control white LED working mode. Press ‘WHITE ONLY’ key, all RGB color will be shutdown and only white LED lights up. Press ‘WHITE OFF’ key, the white LED will turn off and RGB LED remain it’s previous status. 3. White Brightness Adjust white LED brightness. Press the right side key to increase white LED brightness and the left side key to decrease. 4. Static RGB Color Selection These keys control the RGB static color. a) Press color printed keys will set the RGB LEDs to correspond color light as the key. There are 6 shortcut color keys to make direct color selection. b) Press ‘COLOR+’ and ‘COLOR-’ to scroll over all preset static colors, including the 6 shortcut key colors. 5. Color Brightness Adjust RGB color brightness. Press the right side key to increase RGB LED brightness and the left side key to decrease. Select the target zone controlled by remote. The RQ211 master unit is always zone 1 and the RQ212 slave unit can be programmed to any zones. The remote will control the corresponding zone(s) after the specific zone key is pressed once. For every power up for RQ211, the zone is restored to ‘All Zone’. 8. Remote Controller Indicator This blue indicator will blink when remote controller works. The remote controller works at radio frequency, the signal can pass through barrier, so it’s not necessary to aim at the controller when operate the remote. Installing RQ211 and RQ212 can be programmed to a group and operate in different zones. RQ211 is a master controller which receives remote control signal and sends out wireless commands to RQ212. RQ212 is slave controller and can only be programed to RQ211 master controller for group working. For proper wireless working, RQ212 should be in a good wireless receiving range from RQ211. Operation 9. Power Supply The red power cable should be connected to power positive and black to negative. The controller unit can work from DC 6V to 24V, Please make sure the power supply voltage is same as the LED load and the power is capable for the load wattage. 11 10 10. LED Output RQ211/RQ212 supports constant voltage driving LED products with common anode connection. The black cable on the output side is the common node, it connects to the power supply positive inside the controller. The white, green, red and blue cable runs the driving signal of relevant LED color, please connect the color cables to the cathode of relevant color LED loads and the black cable to the common node. 11. Status Indicator This is a full color status indicator. It displays all working status of the controller. It indicates different events as following: Blue: normal working. Short single white flash: new command executed. Long single white flash: reach mode or color cycle edge. Long single yellow flash: reach speed or brightness limit. Red flash: overload protected. Yellow flash: overheat protected. 3). Press remote ‘ON’ and ‘White Bright +’ key together in 5 seconds after RQ212 power on, and then press ‘1 ZONE’, ‘2 ZONE' or ‘3 ZONE’ key in another 5 seconds. After this operation, the RQ212 indicator will also flash white for 3 times to display the programming is accepted, the slave is now programmed to the relevant zone. Advanced Features 15. Waterproof RQ211/212 is a standard version which can be used in dry environments. RQ211/212-S is fully waterproof with IP68 standard, and can be used under water within depth of 30 meters. Note: The remote receiving and master to slave communication sensitivity will decrease when controller installed in wet environment. 16. Protection RQ211/212 series controllers have full protection function for output short circuit, overload, and overheat. The controller will automatically recover from protection when working status is good. Please ensure the LED loads are in rated range, outputs are not shorted and the controller unit is in a good heat dissipation environment to avoid protection. 12. Using Remote Please pull out the battery insulate tape before using. The RF wireless remote signal can pass through some nonmetal barrier. For proper receiving remote signal, please do not install the controller in closed metal parts. 13. Pairing New Remote The remote and RQ211 is 1 to 1 paired as default. Further more, one master unit can be paired to 5 remote controllers and every remote can be paired to any master unit. Please do following steps to pair new remote to RQ211: 1). Plug off the power of RQ211 and plug in again after 5 seconds. 2). Press remote ‘ON’ and ‘White Bright +’ key together in 5 seconds after RQ211 power on, and then press ‘RED’ key in another 5 seconds. After this operation, the RQ211 indicator will flash white for 3 times to display the command is accepted, the master unit now recognizes the new remote. Only 5 latest paired remote controllers can be recognized by RQ211. 14. Program Slave to Zone The RQ212 slave controllers can be programmed to zone1, 2 or 3. There’s no quantity limit in each zone group. Do the following steps to program slave controller to master: 1). Keep the RQ211 controller power on and the remote already paired to it. 2). Plug off the power of RQ212 slave controller and plug in again after 5 seconds. Specification RQ211 RQ211-S RQ212 RQ212-S Model 34 modes Dynamic mode Static Color 30 colors PWM Grade 256 steps 10 levels White Brightness Grade 5 levels Color Brightness Grade Speed Grade 10 levels 6 direct keys None Direct Color Select Yes Overload protection Overheat protection Yes DC 6-24V Working Voltage 433.92MHz Remote frequency None 2.4GHz ISM band Synchronization frequency Remote control distance >15m at open area None >15m at open area Master/Slave sync. Zone Control 3 zones, infinite RQ212 in each zone. 3x2.5A + 4A Rated Output Current IP Grade IP-63 IP-68 IP-63 IP-68 Caution: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference; (2) This device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No Author : Rocky Create Date : 2014:11:27 14:57:41+08:00 Modify Date : 2015:12:16 10:31:14+08:00 XMP Toolkit : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04 Format : application/pdf Creator : Rocky Title : 未命名 -1 Creator Tool : CorelDRAW X6 Metadata Date : 2015:12:16 10:31:14+08:00 Producer : Corel PDF Engine Version 16.1.0.843 Document ID : uuid:899f6f0a-98cd-463b-9baf-6ea69e3bed9f Instance ID : uuid:1b1393a6-ad23-487e-a51a-f21998577180 Page Count : 2 Profile CMM Type : Lino Profile Version : 2.1.0 Profile Class : Display Device Profile Color Space Data : RGB Profile Connection Space : XYZ Profile Date Time : 1998:02:09 06:49:00 Profile File Signature : acsp Primary Platform : Microsoft Corporation CMM Flags : Not Embedded, Independent Device Manufacturer : IEC Device Model : sRGB Device Attributes : Reflective, Glossy, Positive, Color Rendering Intent : Perceptual Connection Space Illuminant : 0.9642 1 0.82491 Profile Creator : HP Profile ID : 0 Profile Copyright : Copyright (c) 1998 Hewlett-Packard Company Profile Description : sRGB IEC61966-2.1 Media White Point : 0.95045 1 1.08905 Media Black Point : 0 0 0 Red Matrix Column : 0.43607 0.22249 0.01392 Green Matrix Column : 0.38515 0.71687 0.09708 Blue Matrix Column : 0.14307 0.06061 0.7141 Device Mfg Desc : IEC http://www.iec.ch Device Model Desc : IEC 61966-2.1 Default RGB colour space - sRGB Viewing Cond Desc : Reference Viewing Condition in IEC61966-2.1 Viewing Cond Illuminant : 19.6445 20.3718 16.8089 Viewing Cond Surround : 3.92889 4.07439 3.36179 Viewing Cond Illuminant Type : D50 Luminance : 76.03647 80 87.12462 Measurement Observer : CIE 1931 Measurement Backing : 0 0 0 Measurement Geometry : Unknown Measurement Flare : 0.999% Measurement Illuminant : D65 Technology : Cathode Ray Tube Display Red Tone Reproduction Curve : (Binary data 2060 bytes, use -b option to extract) Green Tone Reproduction Curve : (Binary data 2060 bytes, use -b option to extract) Blue Tone Reproduction Curve : (Binary data 2060 bytes, use -b option to extract)EXIF Metadata provided by EXIF.tools