Rayson Technology BTM-22X Bluetooth Module User Manual BTM222 DataSheet

Rayson Technology Co., Ltd. Bluetooth Module BTM222 DataSheet

Manual

Rayson  Bluetooth ® Module Class1 BC04-ext Module                                     BTM-222 Features                                                                  Outline        Block Diagram   ■ Bluetooth Ver. 2.0+EDR certification ■ Transmit Power up to +18dBm(class1)   ■ Low current consumption: Hold, Sniff, Park, Deep sleep mode ■ 3.0V to 3.6V operation ■ Full Bluetooth Data rate over UART and USB ■ Support up to 7 ACL links and 3 SCO links ■ Enhanced Data Rate(EDR) compliant for both 2Mbps and 3Mbps modulation modes ■ Interface: USB, UART&PCM( for voice codec) ■ SPP firmware with AT commands ■ RoHS Compliant ■ Small outline:          28.2 X 15.0 X 2.8 mm         Application    ● Access point ● Domestics and Industrial applications ● Serial Adapter ● GPS, POS, Barcode Reader
             Electrical Characteristics Absolute Maximum Ratings Parameter  Min.  Max.  Unit Storage Temperature  -40  +85  ℃℃℃℃ Supply Voltage(VDD)  2.7  3.7  DCV Supply Voltage(PVCC)    3.0  3.6  DCV Other Pin Voltage  Vss-0.4  VDD+0.4  DCV Recommended Operating Conditions Parameter  Min.  Typ.  Unit Temperature  -20  +75  ℃℃℃℃ Supply Voltage(VDD)  3.0  3.3  DCV Supply Voltage(PVCC)  3.0  3.3  DCV General Electrical Specification Parameter  Description  Min.  Typ.  Max.  Unit Carrier Frequency    2.402    2.480  GHz RF Output Power  Measured in 50ohm  15  16.5  18  dBm RX sensitivity    -  -88  -86  dBm Load Impedance  No abnormal Oscillation      5:1   Input Low Voltage  RESET,UART,GPIO,PCM -0.30  -  0.80  DCV Input High Voltage  RESET,UART,GPIO,PCM 0.7VDD -  VDD+0.3 DCV Output Low Voltage  UART,GPIO,PCM  -  -  0.40  DCV Output High Voltage  UART,GPIO,PCM  VDD-0.4 -  -  DCV Average Current Consumption Receive DM1    114    mA   Radio Characteristics - Basic Data Rate  Transmitter , VDD = 3.3V Temperature =+20°C   Frequency (GHz) Min.  Typ. Max.  Bluetooth Specification Unit 2.402  16  17.5  18.5  dBm 2.441  16  17.5  18.5  dBm  RF transmit power 2.480  16  17.5  18.5  -6 to +20 dBm 2.402  -  12  25  kHz 2.441  -  10  25  kHz Initial carrier frequency tolerance 2.480  -  9  25  ±75 kHz 2.402  -  890  1000  kHz 2.441  -  870  1000  kHz -20dB  bandwidth  for  modulated carrier 2.480  -  820  1000  < 1000 kHz 2.402  -  ±10  ±20  kHz 2.441  -  ±10  ±20  kHz Carrier  Frequency  Drift  (single slot packet DH1) 2.480  -  ±10  ±20  <25 kHz 2.402  -  ±10  ±20  kHz 2.441  -  ±10  ±20  kHz Carrier Frequency  Drift (five slot packet DH5) 2.480  -  ±10  ±20  <40 kHz 2.402  -  ±7  ±14  kHz/50µs 2.441  -  ±7  ±14  kHz/50µs  Drift Rate 2.480  -  ±7  ±14  <20 kHz/50µs
RF power control range  16  25  -  >16  dB 2.402  145  165  170  kHz 2.441  145  165  170  kHz  △f1avg   “Maximum Modulation” 2.480  145  165  170  140<△f1avg <175 kHz 2.402  115  150  -  kHz 2.441  115  150  -  kHz  △f2maz   “Minimum Modulation” 2.480  115  150  -  >115 kHz Adjacent channel transmit power F=F0±2MHz -  -35  -20  < - 20 dBm Adjacent channel transmit power F=F0±3MHz -  -45  -40  < - 40 dBm Adjacent channel transmit power F>F0 +3MHz -  -50  -40  < - 40 dBm Adjacent channel transmit power F<F0 -3MHz -  -50  -40  < - 40 dBm           Receiver , VDD = 3.3V Temperature =+20°C   Frequency (GHz) Min.  Typ. Max.  Bluetooth Specification Unit 2.402  -  -88  -86  dBm 2.441  -  -88  -86  dBm Sensitivity at 0.1% BER (Single slot packets)  2.480  -  -88  -86  < - 70 dBm 2.402  -  -88  -86  dBm 2.441  -  -88  -86  dBm Sensitivity at 0.1% BER (Multi slot packets)  2.480  -  -88  -86  < - 70 dBm 2.402  -20  -10  -  dBm 2.441  -20  -10  -  dBm Maximum received signal level at 0.1% BER 2.480  -20  -10  -  > - 20 dBm C/I co-channel  -  6  11  < 11  dB Adjacent channel selectivity C/I F=F0 +1 MHz  -  -4  -  < 0 dB Adjacent channel selectivity C/I F=F0 - 1MHz  -  -4  -  < 0 dB Adjacent channel selectivity C/I F=F0 +2 MHz  -  -38  -  < - 30 dB Adjacent channel selectivity C/I F=F0 - 2MHz  -  -23  -  < - 20 dB Adjacent channel selectivity C/I F>=F0 +3 MHz  -  -45  -  < - 40 dB Adjacent channel selectivity C/I F<=F0 -5 MHz  -  -44  -  < - 40 dB Adjacent channel selectivity C/I F=Fimage -  -22  -  < - 9 dB F0 = 2441 MHz Maximum  level  of  intermodulation  interference (n=5)   -30    > -39 dBm   Radio Characteristics – Enhanced Data Rate Transmitter , VDD = 3.3V Temperature =+20°C   Frequency (GHz) Min. Typ.  Max.  Bluetooth Specification Unit 2.402  -  16  -  dBm 2.441  -  16  -  dBm  Maximum RF transmit power(note) 2.480  -  17  -  -6 to +20 dBm Relative transmit power  -  -1.6  -  -4 to +1  dB π/4 DQPSK Maximum carrier frequency stability    w0 -  2  -  <  ±10 for all blocks kHz π/4 DQPSK Maximum carrier frequency stability    wi -  6  -  <  ±75 for all packets kHz π/4 DQPSK Maximum carrier frequency stability | w0 + wi | -  8  -  <  ±75 for all blocks kHz
8 DPSK Maximum carrier frequency stability    w0 -  2  -  <  ±10 for all blocks kHz 8 DPSK Maximum carrier frequency stability    wi -  6  -  <  ±75 for all packets kHz 8 DPSK Maximum carrier frequency stability | w0 + wi | -  8  -  <  ±75 for all blocks kHz RMS DVEM  -  7 -  < 20  % 99% DEVM  -  13 -  < 30  % π/4 DQPSK Modulation Accuracy Peak DEVM  -  19 -  < 35  % RMS DVEM  -  7 -  < 13  % 99% DEVM  -  13 -  < 20  % 8 DPSK Modulation Accuracy Peak DEVM  -  17 -  < 25  % F>F0 +3 MHz  -  <-50  -  < -40  dBm F<F0 -3 MHz  -  <-50  -  < -40  dBm F=F0 -3 MHz  -  -46  -  < -40  dBm F=F0 -2 MHz  -  -34  -  < -20  dBm F=F0 -1 MHz  -  -35  -  < -26  dBm F=F0 +1 MHz  -  -35  -  < -26  dBm F=F0 +2 MHz  -  -31  -  < -20  dBm In-band spurious emissions F=F0 +3 MHz  -  -33  -  < -40  dBm EDR Differential Phase Encoding    No Errors   > 99  % Receiver , VDD = 3.3V Temperature =+20°C   Modulation  Min. Typ.  Max.  Bluetooth Specification Unit π/4 DQPSK  -  -87  -  < -70 dBm Sensitivity at 0.1% BER 8 DPSK  -  -78  -  < -70 dBm π/4 DQPSK  -  -8  -  > -20 dBm Maximum received signal level at 0.1% BER  8 DPSK  -  -10  -  > -20 dBm π/4 DQPSK  -  10  -  < +13 dB C/I co-channel at 0.1% BER 8 DPSK  -  19  -  < +21 dB π/4 DQPSK  -  -10  -  < 0 dB Adjacent  channel  selectivity  C/I F=F0 +1 MHz  8 DPSK  -  -5  -  < +5 dB π/4 DQPSK  -  -11  -  < 0 dB Adjacent  channel  selectivity  C/I F=F0 -1 MHz  8 DPSK  -  -5  -  < +5 dB π/4 DQPSK  -  -40  -  < -30 dB Adjacent  channel  selectivity  C/I F=F0 +2 MHz  8 DPSK  -  -40  -  < -25 dB π/4 DQPSK  -  -23  -  < -20 dB Adjacent  channel  selectivity  C/I F=F0 -2 MHz  8 DPSK  -  -20  -  < -13 dB π/4 DQPSK  -  -45  -  < -40 dB Adjacent  channel  selectivity  C/I F=F0 +3 MHz  8 DPSK  -  -45  -  < -33 dB π/4 DQPSK  -  -45  -  < -40 dB Adjacent  channel  selectivity  C/I F=F0 -5 MHz  8 DPSK  -  -45  -  < -33 dB F0 = 2405, 2441, 2477 MHz π/4 DQPSK    -20    < -7 dB Adjacent  channel  selectivity  C/I F=Fimage 8 DPSK    -15    < 0 dB  Note : Measurement made using a POWER_TABLE entery of TX_PRE 80, INT PA63, EXT PA255. This ensures that the Bluetooth requirements for ACP and those defined by the FCC and ETSI are satisfied over the operating temperature rang of -5℃℃℃℃to    +45℃℃℃℃. Although the design is capable of generating in excess of +18dBm, regulatory compliance over the full temperature range of -5℃℃℃℃  to +45℃℃℃℃  will not be satisfied if the transmit power approaches this value.
Application Schematic  TitleSize Document Number RevDate: Sheet of<Doc> <Rev Code><Title>A1 1Thursday , June 24, 2010TP6TP5C690.22uFL7TP7R69100KC702.2uFC71CAP NPL8INDUCTORC72CAP NPR7027C732.2uFR71 27SW512E3ANTENNA1TP8R72330J2USB JACKVCC 1D- 2D+ 3GND 4U2XC6209VOUT 5NC 4GND2VIN1CE3D16Blue LED / AP2012PBC3.3V3.3V3.3V3.3VTXRXLinkANTENNAmatchingcircuitTO HostR73330D17LEDR74330D18LEDDataC740.1uU1BTM-222GND1+V_PA2RESET16SPIMISO34SPIMOSI31SPICSB32SPICLK33UART_CTS30UART_TX27UART_RTS28UART_RX26AIO03USBDN 21USBDP 20PCM_IN 23PCM_CLK 25PCM_OUT 24PCM_SYNC 22AIO143V317GND19PIO2 7PIO3 8PIO4 9PIO5 11PIO6 12PIO7 13PIO8 14PIO1 6PIO0 5PIO10 36PIO9 15RFIO 37GND 38GND29PIO11 35GND39GND40GND10GND18     SPP AT Command sets +++  (Escape Sequence) When  the  device  is  in  Data  mode,  it  can  be  forced  back  into  Command  mode  while maintaining the connection to the remote device. The sequence characters should be with 1000ms guard time When  it’s  in  master  mode.  This  command  establish a  connection.  When  it’s  in  slave mode, the command will be rejected. Modifiers  Description A    Connect to a device which has been assigned by “ATD= xxxxxxxxxxxx” A  (Establish  a connection) A1~A8  Connect to a device1~8 in neighborhood found through “ATF?”. This command display the local device BD address Modifiers  Description B  (Display  local BD address)  B?  Inquire the Local BD address This command enable or disable flow control signals (CTS/RTS) of the COM port. Note, the setting is not affected by ATZ0 but will cause a reboot Modifiers  Description C  (Flow   Control)    C0    Disable flow control.
C1   (Default)  Enable flow control. C?  Inquire the current setting For security purpose, We can specifies the unique remote device can be connected. In master  role,  it  automatically  inquire  and  search  the  slave  even  the  slave  is undiscoverable. In slave role, the command should be as a filter condition to accept the master’s inquiry. Modifiers  Description D=xxxxxxxx  "xxxxxxxx" is a string of 12 hexadecimal digits. D0   (Default)   Clear Remote BD address setting, inquire any slave in master mode or accept any master in slave mode. D  (Set  Remote BD address) D?  Inquire the Remote BD address setting This command specifies whether the device should echo characters received from the UART back to the Host Modifiers  Description E0    Characters received from the UART are not echoed back to the Host E1   (Default)    Characters received from the UART are echoed back to the Host. E  (Local   Echo)  E?  Inquire the current setting This command is used to find any bluetooth device in neighborhood within 60 seconds timeout. If any device is found,  its name and address will be  listed. The search ends with a message “Inquiry ends, xx device(s) found.” This command is available only when the adaptor is in the manual master role. An AT can cancel the Inquiry. Modifiers  Description F  (Find  Bluetooth device) F?  Inquire scan max. 8 Bluetooth neighborhood devices. This command is used to drop connection either master or slave role. And it is used to specifiy whether the device could be discovered by remote master device.   note : it will cause a reboot when ATH0 or ATH1 take the effect Modifiers  Description H Drop current connection in Online command mode H0  The device enters undiscoverable mode. If a pair have been made, the original  connection  could  be  connected  again.  Other  remote  master device can not discovery this device. H1   (Default)  The device enters discoverable mode. H  (Discoverable  Control)   H?  Inquire the current setting This command is used to Inquiry the information Modifiers  Description I0 Inquire the version Codes I1 Listing all setting value I  (Information)  I2 Inquire RSSI in Online command mode This command is used to specify one or two stop bits of COM port Modifiers  Description K0   (Default)    One Stop bit K  (Stop  bits setting)   K1  Two stop bits
K?  Inquire the current setting This command is used to specify the baud rate of COM port Modifiers  Description L*  1200bps L#  2400bps L0    4800bps L1    9600bps L2 (Default)  19200bps L3    38400bps L4    57600bps L5  115200bps L6  230.4Kbps L7  460.8Kbps L8  921.6Kbps L  (Baud Rate   Control)   L?  Inquire the current setting This command is used to specify the parity bit setting of COM port Modifiers  Description M0   (Default)    None Parity bit. M1  Odd parity setting. M2  Even parity setting M  (Parity  bits setting)   M?  Inquire the current setting We can specifies the device a friendly name using 0 to 9, A to Z, a to z, space and –, which are all valid characters. Note that "firs space or -, last space or – isn’t permitted". The default name is “Serial Adaptor” Modifiers  Description N=xxxxx  "xxxxx" is a character string, maxima length is 16 N  (Set  device name)   N?  Inquire the device name This command is used to enable/disable auto-connection feature in master role. By the way, it is used to online switch from command mode to data mode. Note, it will cause a reboot when ATO0 or ATO1 take effect. Modifiers  Description O Online switch from command mode to data mode O0   (Default) Automatically connectting to a device which is assigned in “ATD” or any available device if “ATD” was not assigned. O1  Disable  auto-connection  feature,  user  should  manually  use  “ATA” command to connect a remote device.   O  (Auto  connect setting)   O?  Inquire the current setting This  command  specifies  the  PIN  number.  It  control  to  off  the  PIN  code  authorization that allow to establish a connection without PIN code. Default PIN number is "1234" Modifiers  Description P  (Set PIN code) P=xxxx (Default)  "xxxx" is 4~8 digit string
P0    Turn off the PIN code authorization P?  Inquire the current PIN number The command is used to determine if result Codes should be sent to the Host. When result Codes are supressed, the device does not generate any characters in response to the completion of a command or when an event occurs. Four Result Codes : OK,CONNECT,DISCONNECT,ERROR Modifiers  Description Q0   (Default)    The device will prompt Result Codes Q1  The device will not prompt Result Codes Q  (Result   Code   Supression)   Q?  Inquire the current setting This command specifies whether the device could be master or slave device. If change the role, the adaptor will reboot and clear all paired addresses. Modifiers  Description R0    The device as master role. R1   (Default)    The device as slave role. R  (Set Role)   R?  Inquire the current setting This command is used to disable/enable escape sequence “+++”. Modifiers  Description X0    Disable escape character check. X1   (Default)    Enable escape character check. X  (Escape Control) X?  Inquire the current setting This command is used to restore default setting and reboot Modifiers  Description Z  (Restore) Z0    Restore the default setting The factory settings of UART are as follows:  Baud rate: 19200 bps  Data bit: 8  Parity: none  Stop bit: 1  Flow control: H/W or none
BTM-222 Pin Function     Pin No. Pin Name  Pin Type  Description 1  GND  GND  Common ground 2  PVCC  Power  Power Amp. Power Supply(3.3V) 3  AIO(0)  Bi-directional Programmable I/O terminal 4  AIO(1)  Bi-directional Programmable I/O terminal 5  PIO(0)  Bi-directional Programmable I/O terminal 6  PIO(1)  Bi-directional Programmable I/O terminal 7  PIO(2)  Bi-directional Programmable I/O terminal 8  PIO(3)  Bi-directional Programmable I/O terminal 9  PIO(4)  Bi-directional Programmable I/O terminal, (Button Input, active high) To press the button caused disconnection or reconnection. To double click the  button caused clear all original link records then  repairing.  When  user  press  the  button  more  than  3 seconds, then it will restore the default RS232 setting 10  GND  GND  Common ground 11  PIO(5)  Bi-directional Programmable I/O terminal, (Drive Data status led, active high, it will flash 3 times when it reboot). 12  PIO(6)  Bi-directional Programmable I/O terminal, (RFCOMM connection status). 13  PIO(7)  Bi-directional Programmable I/O terminal, (Drive Link status led, active high, it will flash 3 times when it reboot). 14  PIO(8)  Bi-directional Programmable I/O terminal, (Drive  Power  status  led,  active  high,  it will flash 3 times when it reboot). 15  PIO(9)  Bi-directional Programmable I/O terminal, (Drive RS232 force on, active high). 16  RESETB  CMOS input  Reset input of module, Active low 17  VCC  Power  3.3V power supply input 18  GND  GND  Common ground 19  GND  GND  Common ground 20  USB_DP  Bi-directional USB data plus 21  USB_DN  Bi-directional USB data minus       22  PCM_SYNC Bi-directional Synchronous data sync 23  PCM_IN  CMOS input  Synchronous data input 24  PCM_OUT  CMOS output Synchronous data output 25  PCM_CLK  Bi-directional Synchronous data clock 26  UART_RX  CMOS input  UART data input 27  UART_TX  CMOS output UART data output 28  UART_RTS CMOS output UART request to send(active low) 29  GND  GND  Common ground 30  UART_CTS CMOS input  UART clear to send(active low) 31  SPI_MOSI  CMOS input  Serial Peripheral Interface data input 32  SPI_CSB  CMOS input  Chip select for Synchronous Serial Interface(active low) 33  SPI_CLK  CMOS input  Serial Peripheral Interface clock 34  SPI_MISO  CMOS output Serial Peripheral Interface data output 35  PIO(11)  Bi-directional Programmable I/O terminal 36  PIO(10)  Bi-directional Programmable I/O terminal 37  RF_IO  Analogue  Antenna interface 38  GND  GND  Common ground
            BTM-22x Dimension
Qualified Product Notice   BQB: Juei-Hsin Chin   Hyper Taiwan Technology, Inc. 7F-1, No. 92, Sec.1 Nei-Hu Rd., Taipei Taiwan, R.O.C. 114    Assessment Date    11.10.2005   QPN Number    QPNHTTJ050   Listing Date    11.10.2005    Applicant Information   Applicant    Rayson Technology Co., Ltd    Contact Person    Tim Lin   Address    1F, No. 9, R&D Rd. 2, Science-Based    Phone Number    +886.3.563.3666    Industrial Park, Hsin-Chu, 300 Taiwan, R.O.C    Fax Number    +886.3.563.3688   URL    http://www.rayson.com    Email Address    sales@mail.rayson.com    Manufacturer Information    Product Information   Product Name    Class 1 Module    Product Category    Components   Product ID    BTM-22x, BTM-23x    Product Type    Comp-HW-Integrated   Hardware Version    A1    Software Version    N/A   Firmware Version    cyt_8unified_fl_bt2.0_19p2   Supported Protocol    RF, BB, LM, HCI, HCI-USB, HCI-RS232, HCI-UART, L2CAP, SDP, RFCOMM   Supported Profile    GAP, SPP    Reference Information   Product Reference Document    V1.0   Bluetooth Specification    V2.0 + EDR   Test Case Reference List    TCRL_EDR_2005-1-BQRB1, TCRL_P1_1_2005-1-BQRB1    I certify that the Class 1Module has a Bluetooth Brand License based on the requirements as described in Section 6.2.1, Pre-Tested Bluetooth Components, of the Bluetooth Program Reference Document 1.0   San Lorenzo, California / 11.10.2005
BTM-222 Regulation Statement --------------------------------------- In accordance with FCC Part 15C BTM222, this module is    listed as a Limited Modular Transmitter device.  Therefore, the final host product must be submitted to Rayson Technology Co., Ltd. for confirmation that the installation  of  the  module  into  the  host  is  in  compliance  with  the  regulations  of  FCC  and  IC  Canada. Specifically, if an antenna other than the model documented in the Filing is used, a Class 2 Permissive Change must be filed with the FCC.  Changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment.  IV. FCC Label Instructions The outside of final products that contains this module device must display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains Transmitter Module FCC ID: QWOBTM-22X” or “Contains FCC ID: QWOBTM-22X.” Any similar wording that expresses the same meaning may be used.

Navigation menu