Rca Rp5640 Users Manual RP5640_EN(US)

: Rca Rca-Rp5640-Users-Manual-650697 rca-rp5640-users-manual-650697 rca pdf

Open the PDF directly: View PDF .
Page Count: 1

Before You Begin

General Controls Clock

Important InformationFCC Information Safety Information

English

Radio

It is important to read this instruction book prior to using your new product for the first time.

RP5640

user

manual

WARNING:

TO PREVENT FIRE OR ELECTRICAL

SHOCK HAZARD, DO NOT EXPOSE THIS PRODUCT

TO RAIN OR MOISTURE.

SEE MARKING ON BOTTOM / BACK OF PRODUCT

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

THE EXCLAMATION

POINT WITHIN THE

TRIANGLE IS A

WARNING SIGN

ALERTING YOU OF

IMPORTANT

INSTRUCTIONS

ACCOMPANYING

THE PRODUCT.

THE LIGHTNING

FLASH AND ARROW-

HEAD WITHIN THE

TRIANGLE IS A

WAR NING SIGN

ALERTING YOU OF

"DANGEROUS

VOLTAGE" INSIDE

THE PRODUCT.

CAUTION: TO REDUCE THE

RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER

(OR BACK). NO USER-

SERVICEABLE PARTS IN-

SIDE. REFER SERVICING

TO QUALIFIED SERVICE

PERSONNEL.

GEFAHR EINES 

ELEKTRISCHEN SCHLAGS

Wake Function

EN/E

FCC Information

This device complies with Part 15 of the FCC

Rules. Operation is subject to the following two

conditions: (1) This device may not cause harmful

interference, and (2) this device must accept any

interference received, including interference

that may cause undesired operation.

In accordance with FCC requirements, changes

or modifications not expressly approved by

Thomson Inc. could void the user’s authority to

operate this product.

This device generates and uses radio frequency

(RF) energy, and if not installed and used

properly, this equipment may cause interference

to radio and television reception.

If this equipment does cause interference to

radio or television reception (which you can

determine by unplugging the unit), try to correct

the interference by one or more of the following

measures:

• Re-orient the receiving antenna (that is, the

antenna for the radio or television that is

“receiving” the interference).

• Move the unit away from the equipment that

is receiving interference.

• Plug the unit into a different wall outlet so

that the unit and the equipment receiving

interference are on different branch circuits.

If these measures do not eliminate the

interference, please consult your dealer or an

experienced radio/television technician for

additional suggestions. Also, the Federal

Communications Commission has prepared a

helpful booklet, “How To Identify and Resolve

Radio TV Interference Problems.” This booklet

is available from the U.S. Government Printing

Office, Washington, DC 20402. Please specify

stock number 004-000-00345-4 when ordering

copies.

This product complies with DHHS rules 21CFR

subchapter J. appliable at date of manufacture.

For Your Safety

The AC power plug is polarized

(one blade is wider than the

other) and only fits into AC

power outlets one way. If the

plug will not go into the outlet

completely, turn the plug over

and try to insert it the other

way. If it still does not fit, contact a qualified

electrician to change the outlet, or use a

different one. Do not attempt to bypass this

safety feature.

For Your Records

I

n the event that service should be required, you

may need the model number. In the space

below, record the date and place of purchase:

Date of Purchase:

Place of Purchase:

Service Information

This product should be serviced only by those

specially trained in appropriate servicing

techniques. For instructions on how to obtain

service, refer to the warranty included in this

Guide.

Technical Information

Product: Clock Radio with CD player

Brand: RCA

Model: RP5640

Electrical Consumption

Power Supply: 120V ~ 60Hz

Power Consumption: 22 Watts

IMPORTER

Comercializadora Thomson de México, S.A. de C.V.

Álvaro Obregón No. 151. Piso 13.

Col. Roma. Delegación Cuauhtémoc

C.P. 06700. México, D.F.

Telefono: 52-55-11-020360

RFC: CTM-980723-KS5

The descriptions and characteristics in this owner’s manual are for the purpose of general reference only and not

as a guarantee. In order to provide you with the highest quality product, we may make changes or modifications

without prior notice. The English version serves as the final reference on all product and operational details

should any discrepancies arise in other languages.

•Make sure that you keep your set

away from water and high

temperatures.

• Do not use your system immediately

after transporting it from a cold place

to a warm place, as condensation may

cause the system to malfunction.

• Keep your unit away from humid

areas and abnormally hot places.

• To prevent personal injury, do not

reverse any batteries.

•The use of apparatus in moderate

climates.

•The apparatus shall not be exposed to

dripping or splashing and that no

objects filled with liquids, such as

vases, shall be placed on the

apparatus.

•No naked flame sources, such as

lighted candles, should be placed on

the apparatus.

•Attention should be drawn to the

environmental aspects of battery

disposal.

•Minimum distances (2cm) around the

apparatus for sufficient ventilations.

•The ventilation should not be

impeded by covering the ventilation

opening with items, such as

newspaper, table-cloths, curtains, etc.

•The rating plate is located at the

bottom cabinet of apparatus.

Ecology

Help protect the environment - we

recommend that you dispose of used

batteries by putting them into specially

designed receptacles.

Maintenance

Clean the unit with a soft cloth, or a damp

chamois leather. Never use solvents.

Power Failure Indicator

When AC power is interrupted (disconnected)

for a short period of time, both time and

alarm settings will change (unless battery is

installed). After AC power is restored

(reconnected), the Digital Display will blink to

indicate that power was interrupted and you

should readjust the time and alarm settings.

Plugging In For Power

AC OUTLET POWER SUPPLY:

120V~60Hz

Note:Note:

Note:Note:

Note:

Power is fed to the unit even

when it is not functioning. To cut

the power supply off, the power cable

must be unplugged.

Before You Plug for Power

1. Setting Time Zone

You may slide the time zone selector at

the bottom of the unit to 1) Eastern,

2) Central, 3) Mountain or 4) Pacific. (refer

to the maps on the right)

2. Day Light Saving

You can press and hold for a few seconds

the day light saving switch at the bottom

of the unit to turn on/ off in areas

observing/ not observing such time

change.

WARNING: Please avoid playing with

these buttons after entering the

Clock/Alarm set mode.

Auto Clock Set

You do not have to set the clock time as a

built-in automatic time set system is

equipped in this clock powered by 3V (2

X AA batteries (included). All you have to

do is to plug this clock for power and

current time will be shown automatically.

However, the batteries can also be

exhausted and we recommend that you

replace the batteries every 2-3 years. In

case the memory holding batteries are

accidentally removed, you may set the

clock manually with following procedures:

1. Be sure Time Zone and Daylight Saving

Time is adjusted before operating the

clock.

2. Press SET CLOCK/WAKE repeatedly

until the clock setting icon is

displayed.

Wake Function Wake Function

Clock

US Time Zones

Canadian Time Zones

Battery Back-Up Operation

This clock radio is equipped with a

memory holding system that can be

powered with 2 “AA” batteries (included

and installed). The power failure

protection circuit will not operate unless

battery is installed. When normal

household power is interrupted, or AC line

cord is unplugged, the batteries will

power the clock radio to keep track of

time and alarm settings programmed into

memory. When the battery backup

functions, the digital display will not light,

however, the function of alarm still occurs

during the power interruption if

remaining battery power is adequate.

Normal operation will resume after AC

power is restored so you will not have to

reset the time or the alarm.

Replace batteries as follow:

1. Remove battery compartment door

(located at the bottom of the radio)

by applying thumb pressure to the

tab on battery door and then lift the

door out and off the cabinet.

2. Replace 2 AA batteries.

3. Replace the compartment door.

Note: we recommend that you replace the

batteries every 2-3 years.

Limited Warranty (United

States)

What your warranty covers:

• Defects in materials or workmanship.

For how long after your purchase:

• One year from date of purchase.

The warranty period for rental units begins with

the first rental or 45 days from date of shipment to

the rental firm, whichever comes first.

What we will do:

• Provide you with a new, or at our option, a

refurbished unit. The exchange unit is under

warranty for the remainder of the original

product’s warranty period.

• Proof of purchase in the form of a bill of sale or

receipted invoice which is evidence that the

product is within the warranty period must be

presented to obtain warranty service. For rental

firms, proof of first rental is also required.

How to make a warranty claim:

• Properly pack your unit. Include any cables, etc.,

which were originally provided with the product.

We recommend using the original carton and

packing materials.

• Include evidence of purchase date such as the bill

of sale. Also print your name and address and a

description of the defect. Send via standard UPS

or its equivalent to:

Thomson Inc.

Product Exchange Center

11721 B Alameda Avenue

Socorro, Texas 79927

• Insure your shipment for of loss or damage.

Thomson accepts no liability in case of damage or

loss en route to Thomson.

• Pay any charges billed to you by the Exchange

Center for service not covered by the warranty.

• A new or refurbished unit will be shipped to you

freight prepaid.

What your warranty does not cover:

• Customer instruction. (Your Owner’s Manual

provides information regarding operating

Instructions and user controls. For additional

information, ask your dealer.)

• Installation and set-up service adjustments.

• Batteries.

• Damage from misuse or neglect.

• Products which have been modified or

incorporated into other products.

• Products purchased or serviced outside the USA.

• Acts of nature, such as but not limited to lightning

damage.

Limitation of Warranty:

• THE WARRANTY STATED ABOVE IS THE ONLY

WARRANTY APPLICABLE TO THIS PRODUCT. ALL

OTHER WARRANTIES, EXPRESS OR IMPLIED

(INCLUDING ALL IMPLIED WARRANTIES OF

MERCHANTABILITY OR FITNESS FOR A PARTICULAR

PURPOSE) ARE HEREBY DISCLAIMED. NO VERBAL

OR WRITTEN INFORMATION GIVEN BY THOMSON

INC., ITS AGENTS OR EMPLOYEES SHALL CREATE A

GUARANTY OR IN ANY WAY INCREASE THE SCOPE

OF THIS WARRANTY.

• REPAIR OR REPLACEMENT AS PROVIDED UNDER

THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE

CONSUMER. THOMSON INC. SHALL NOT BE LIABLE

FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES

RESULTING FROM THE USE OF THIS PRODUCT OR

ARISING OUT OF ANY BREACH OF ANY EXPRESS OR

IMPLIED WARRANTY ON THIS PRODUCT. THIS

DISCLAIMER OF WARRANTIES AND LIMITED

WARRANTY ARE GOVERNED BY THE LAWS OF THE

STATE OF INDIANA. EXCEPT TO THE EXTENT

PROHIBITED BY APPLICABLE LAW, ANY IMPLIED

WARRANTY OF MERCHANTABILITY OR FITNESS FOR

A PARTICULAR PURPOSE ON THIS PRODUCT IS

LIMITED TO THE APPLICABLE WARRANTY PERIOD SET

FORTH ABOVE.

How state law relates to this warranty:

• Some states do not allow the exclusion nor limitation

of incidental or consequential damages, or limitations

on how long an implied warranty lasts, so the above

limitations or exclusions may not apply to you.

• This warranty gives you specific legal rights, and you

also may have other rights that vary from state to state.

If you purchased your product outside the USA:

This warranty does not apply. Contact your dealer for

warranty information.

This Class B digital apparatus complies with

Canadian ICES-003.

Cet appareil numérique de la class B est

conforme à la norme de NMB-003 du Canada.

Auto Dimmer

Slide the AUTO DIMMER switch at the back

of the unit to the ON position. The brightness

of the LCD display will vary automatically

according to the environment.

Slide to the OFF position, the display will

remain at its brightest level.

Backlight Color Select

You can choose among 4 different backlight

color - blue, green, white and amber.

1. Before a specific color is set, the backlight

color will keep changing.

2. Press Color Select at the back of the unit

to toggle among different backlight color.

3. If the AC power and backup batteries are

removed, the 4 backlight colors will

starting changing again once the AC

power is resumed.

Precautions

•Never open the cabinet under any

circumstances. Any repairs or internal

adjustments should be made only by a

trained technician.

•Warning: Never operate this product with

the cabinet removed.

•The CD player of this unit uses a laser to

read the music on the disc. The laser

mechanism corresponds to the cartridge

and stylus of a record player. Although

this product incorporates a laser pick-up

lens, it is completely safe when operated

according to directions.

• Discs rotate at high speed inside the

player. Do not use damaged, warped or

cracked discs.

•Do not touch the pick-up lens which is

located inside the disc compartment. Also,

to keep dust from collecting on the pick-

up lens, do not leave the compartment

door open for an extended period of time.

NAP & Sleep Function

Display

Tip:Tip:

Tip:Tip:

Tip:

If you set the Wake function

with low volume level before

going to bed, we advise using Waking

to Alarm Tone mode to wake you up

since the volume will automatically

increase.

Main plug is used as the disconnect device, it shall

remain readily operable and should not be

obstructed during intended used. To be

completely disconnected the apparatus from

supply mains, the main plug of the apparatus

shall be disconnected from the mains socket

outlet completely.

Es importante leer este manual antes de usar por vez primera su euipo.

Please refer to the actual unit when

reading the instructions below:

Front View

WAKE UP CD TRACK / STATION- sets the

wake up radio station or CD track.

- selects repeat 1 / repeat all / shuffle

/ repeat shuffle in CD mode.

- skips / searches backward.

- starts / pauses CD playback.

- skips / searches forward.

- stops CD playback.

OFF - turns off the radio / alarm / CD

RECALL - recalls available preset radio

stations.

MEMO/SET - sets and stores preset

memory in radio mode.

SNOOZE - turns off the alarm

momentarily.

VOLUME - decreases volume.

VOLUME - increases volume.

RADIO ON/BAND - turns on the radio /

changes radio band.

Top View

OPEN / CLOSE - opens / closes the CD

compartment.

WAKE 1 - activates/inactivates WAKE 1

setting, press repeatedly to cycle wake

mode:

v

v

v

v

WAKE 2 - activates/inactivates WAKE 2

setting, press repeatedly to cycle wake

mode:

v

v

v

NAP - sets the alarm to sound after a

specific period of time. (Alarm tone only)

1

2

3

4

12

34

3. Press REV or FWD to set the time. Press

and hold the respective buttons

to fast reverse or fast forward clock

time.

4. Clock time will automatically be

saved if no buttons are pressed after

a few seconds. You can also press SET

CLOCK/WAKE once to save your setting

and exit clock set mode.

AUDIO-IN - selects auxiliary audio input

mode.

SLEEP - activates SLEEP function.

SET CLOCK / WAKE - sets clock time and

wake setting.

REV / FWD - change time / radio frequency /

CD track

INSTANT WEATHER - recalls available

weather stations.

Bottom View

1 2 3 4

. . . .

- slide to select different time zone.

DAYLIGHT SAVING TIME - Press and hold for

a few seconds to turn on / off the Daylight

Saving function.

Battery compartment - see “Battery Back-up

Operation”.

Back View

AUDIO-IN - auxiliary audio input jack.

COLOR SELECT - press to toggle among 4

backlight colors.

AUTO DIMMER - turns on / off the auto

dimmer function.

Radio

Using the Weather Band

Weather information is given continuously

from U.S. Government Weather Stations

on frequencies from 162.4MHz to

162.55MHz. The Weather transmission,

broadcast 24 hours a day, are taped

messages that are repeated every 4 to 6

minutes and revised and updated as

needed to match the changing weather

conditions. For additional information,

check your location office of the National

Weather Service (Department of

Commerce).

1. Press INSTANT WEATHER to access

Weather Bands with strong signals to

the unit.

2. Press REV or FWD to select among the

7 weather channels.

3. Wx and the corresponding channel

number will show on the display.

IMPORTANT:

The listening range of NOAA weather

stations varies from 10 miles up to a

maximum of 40 miles from the station’s

transmitter. In some areas of the United

States, weather transmissions cannot be

monitored. The effective range of this

radio will have side variations due to the

height of the local transmitting antenna,

atmospheric conditions, and the terrain

between the transmitter and your radio’s

location.

Weather band: CH 1 - 162.550 MHz, CH 2

- 162.400 MHz, CH 3 - 162.475 MHz, CH 4 -

162.425 MHz, CH 5 - 162.450 MHz, CH 6 -

162.500 MHz, CH 7 - 162.525 MHz

TV Band

CH 2-13 are available for TV Band.

1. Press RADIO ON / BAND to access TV

Bands.

2. Press REV or FWD to select among the TV

channels.

3. TV and the corresponding channel

number will show on the display.

TV band: CH 2 - 59.75 MHz, CH 3 - 65.75

MHz, CH 4 - 71.75 MHz, CH 5 - 81.75 MHz, CH

6 - 87.75 MHz, CH 7 - 179.75 MHz, CH 8 -

185.75 MHz, CH 9 - 191.75 MHz, CH 10 -

197.75 MHz, CH 11 - 203.75 MHz, CH 12 -

209.75 MHz, CH 13 - 215.75 MHz

Antennas

FM antenna - The power cord acts as your FM

antenna. It picks up moderate to strong radio

stations and eliminates the need for an

external antenna in most strong signal areas.

Be sure the power cord is stretched to its full

length. Do not coil or bunch the cord

together. Changing position of the power

cord may improve reception.

AM Antenna - A built-in ferrite rod antenna

eliminates the need for an outside antenna

for AM reception. Rotating the unit slightly

may improve reception of distant AM

stations.

Tuning the Stations

1. Press RADIO ON/BAND (located on

the front of the radio) to turn on the

radio.

2. Press RADIO ON/BAND repeatedly to

select the desired broadcast band.

3. Press REV or FWD to tune to your

desired radio station.

4. Press VOLUME + / - to adjust to your

desired listening level.

Setting the Preset Radio

Stations

1. Press RADIO ON/BAND to turn on the

radio.

2. Press RADIO ON/BAND to change the

broadcast band.

3. Press REV or FWD to tune to your

desired radio station.

4. If you want to memorize this radio

station, press MEMO/SET once, and

then press RECALL repeatedly to

choose the radio station number you

want to record in.

5. Press MEMO/SET again to confirm.

6. If you set the radio station in the AL

location, it will be the wake up radio

station of the alarm.

Automatic Radio Station

Search

1. Press RADIO ON/BAND (located on the

front of the radio) to turn on the radio.

2. Press and hold REV or FWD for 2

seconds, it will automatically search a

radio station for you.

Selecting the Preset Radio

Stations

1. Press RADIO ON/BAND to turn on the

radio.

2. Press RECALL repeatedly to select your

desired preset radio station.

Overwriting the Preset Radio

Stations

1. Press RADIO ON/BAND to turn on the

radio.

2. Press REV or FWD to tune to your desired

preset radio station.

3. Press MEMO/SET once and then press

RECALL repeatedly to choose the radio

station number you want to overwrite.

4. Press MEMO/SET again to confirm.

Deleting the Preset Radio

Stations

1. Press RECALL repeatedly to select your

preset radio station you want to delete.

2. Press and hold MEMO/SET for 3 seconds

to delete the selected preset radio

station.

5633 9330 (EN/E)

EXPORTER

Thomson Inc.

P.O. Box 1976

Indianapolis, IN 46206 - 1976

©2006 Thomson Inc.

Trademark(s) ® Registered

Marque(s) ® Deposée(s)

Marca(s) ® Registrada(s)

www.rca.com

Printed in China / Impreso en China

IMPORTADOR

Comercializadora Thomson de México, S.A. de C.V.

Álvaro Obregón No. 151. Piso 13.

Col. Roma. Delegación Cuauhtémoc

C.P. 06700. México, D.F.

Telefono: 52-55-11-020360

RFC: CTM-980723-KS5

CD Player

Listening to Compact Disc

1. Press OPEN/CLOSE to open the CD

compartment.

2. Insert a disc, press OPEN/CLOSE to

close the CD compartment door.

3. Press .

4. Press VOLUME + / - to adjust to your

desired listening level.

5. Press or to skip backward or

forward the CD track.

6. Press and hold or to search

backward or forward within the CD

track.

7. Press to stop CD playback.

Selecting Play Mode

1. Start CD playback.

2. Press to toggle between different

play modes.

- repeats the current track.

- repeats the whole disc.

- plays tracks randomly.

- plays random track repeatedly.

Listening to Auxiliary Source

1. Connect auxiliary input source (e.g. mp3

player) with a line-in cable (included) to

the AUDIO IN jack of the unit.

2. Press AUDIO IN to select auxiliary input

mode with AUDIO-IN shows on the

display.

3. Adjust volume by pressing VOLUME

, control other playback operations

on the auxiliary unit.

Wake Function

Setting the Wake Time

1. Press SET CLOCK/WAKE repeatedly

until

WAKE 1

or

WAKE 2

icon shows on

the display.

2. Press REV or FWD to set the wake

time. The time decrements or

increments will follow by a faster rate

when you press and hold either REV or

FWD.

3. Press SET CLOCK/WAKE repeatedly to

exit setting wake time mode. Or else

the unit will exit setting wake time

mode when no button is pressed

within 5 seconds.

Selecting Wake Mode

To change to another wake mode (e.g. from

CD to radio), simply press WAKE 1 or WAKE

2 repeatedly to scroll through wake options.

Waking to Alarm Tone

When waking to alarm tone is selected, /

icon will light.

You cannot adjust the alarm tone with

volume.

•When the AC power is disconnected, the

unit will enter DC backup mode, all wake

mode will be reverted to alarm tone.

•The unit equips with GRAD-U-WAKE

feature, the alarm tone volume will

increase gradually to its maximum in

about 30 to 45 seconds.

Waking to CD

When the waking to CD is selected, /

icon will light.

1. Press to turn on the CD.

2. Set the wake time.

3. Press WAKE 1 or WAKE 2 to select

waking up by CD, / will light

accordingly.

4. Press VOLUME + / - to adjust to your

desired wake up volume.

5. Press OFF to stop the CD playback.

You can select your CD wake up track by

the following procedures.

1. In CD mode, while pressing WAKE UP

CD TRACK / STATION, press REV or

FWD to select your desired CD wake

up track.

2. Release WAKE UP CD TRACK /

STATION, and the CD wake up track is

set.

3. To reset the CD wake up track, follow

the above procedures and set the CD

wake up track to 1.

Note: If the CD compartment is empty,

the alarm tone will sound instead even

the WAKE TO CD mode is selected.

Waking to RADIO

When the waking to radio is selected, /

icon will light.

1. Press RADIO ON/BAND to turn on the

radio.

2. Set the wake time .

3. Press WAKE 1 or WAKE 2 to select

waking up by RADIO /

will light

accordingly.

4. Press VOLUME + / - to adjust to your

desired wake up volume.

5. Press OFF to turn off the radio.

You can select your wake up radio station by

the following procedures.

1. Press RADIO ON/BAND to turn on the

radio and select the band.

2. Press REV or FWD to tune to your desired

radio station.

3. Press and hold WAKE UP CD TRACK /

STATION to store the current radio station

as the wake up radio station. will

show on the display.

Note: “AL” refers to the Alarm Station. If no

WAKE STATION is set, the wake up radio

station will stay at your last listening radio

station.

You can cancel your wake up radio station by

the following procedures.

1. Press RADIO ON/BAND to turn on the

radio.

2. Press RECALL repeatedly to select the

wake up radio station.

3. Press and hold MEMO/SET to cancel the

wake up radio station.

Turning off Wake Function

1. Silence the alarm momentarily

Press SNOOZE. The alarm will sound again

when the snooze period is over. (see

“SmartSnooze

TM

” section).

2. Stop the alarm

Press OFF and the alarm will be on again the

following day at the same time.

3. Disable the alarm permanently

•Press WAKE 1 or WAKE 2 repeatedly

until no corresponding wake indicator

(e.g. / / ) shows on the display.

•To activate the wake function again, press

WAKE 1 or WAKE 2 repeatedly until a

desired wake mode indicator shows on

the display. The previously set wake time

remains unchanged.

Note: Whenever the unit is in wake up

setting mode and wake up on mode, the

backlight color will changed into red,

regardless of the previously set backlight

color.

SmartSnooze

TM

This operation allows extra sleep time

after the wake function is on. The alarm

will be off by pressing SNOOZE, SLEEP,

AUDIO-IN, NAP, WAKE 1, WAKE 2,

SET, INSTANT WEATHER or OPEN/

CLOSE until the snooze period is over.

Snooze function can be used repeatedly

up to 30 minutes (default: 9 minutes).

After this, the wake function will turn off

until the next day.

Set the “quiet” period as follow:

While pressing SNOOZE, press REV or

FWD to set the “quiet” period (the

default time is 9 minutes) from 1 minute

to 30 minutes. Release SNOOZE, then the

“quiet” period is set.

Sleep Mode

In sleep mode, the radio and CD will turn

off automatically. To set the sleep time,

simply:

1. Press SLEEP, then the time display will

exhibit 0:59 and the radio will turn on

(default). While holding SLEEP, press

REV or FWD to set the sleep time. The

time range is from 1 minute to 2 hours

(default is 0:59).

2. Release SLEEP and the current time

will be shown again, will show on the

display, and the sleep time is set.

• Press SLEEP to read the remaining

sleep time.

Sleep to Radio

1. Under sleep mode, press RADIO ON /

BAND to turn on the radio.

2. Sleep radio station will automatically

switch to the current radio station, you

may select the radio station as usual.

3. Once the sleep time is reached, the radio

will turn off automatically.

You can reset to sleep to a different radio

station, simply:

1. Press RADIO ON/BAND.

2. Press REV or FWD to tune to the radio

station you want to sleep to.

Sleep to CD

1. Under sleep mode, press to start CD

playback.

2. CD play mode will be automatically in

Repeat All mode when using Sleep to CD

setting.

3. The unit will turn off automatically once

the sleep time is reached.

NAP Mode

For catnaps up to 2 hours without

disturbing the regular alarm settings, the

NAP function wakes you up after a short

period of time. Simply:

1. Press NAP, the NAP indicator will flash.

While the NAP indicator is flashing,

press REV or FWD to adjust nap time.

The time range is from 10 minutes to 2

hours at 10 minutes interval (default is

20 minutes).

2. Wait 3 seconds or press NAP again to

confirm, the NAP indicator will show

on the display.

3. Press NAP once to show time left, after

3 seconds, the display will return to

clock time.

Note:

•Only alarm tone can be selected in

NAP mode.

•When the NAP alarm sounds, you can

press OFF to stop it.

•Press and hold NAP for 5 seconds or

select NAP time to 0 minutes to cancel

the NAP function.

Note:

•If you decide to turn off the unit sooner,

press SNOOZE or OFF.

• The unit will enter either CD or Radio

mode after SLEEP is pressed, depending

on the previous sleep setting.

•When the sleep mode is activated again,

the sleep time will be the same as the

one you have set before.