Realtek Semiconductor RTL8821CE 802.11 a/b/g/n/ac RTL8821CE Combo module User Manual PRODUCT SPECIFICATION

Realtek Semiconductor Corp. 802.11 a/b/g/n/ac RTL8821CE Combo module PRODUCT SPECIFICATION

User Manual OEM Manual for Restricted host platform

            (Realtek RTL8821CE) Combo NGFF Type2230 Module OEM Instructions  Preliminary Version 05/09/2016       Realtek Semiconductor Corp. No. 2, Innovation Road II, Hsinchu Science Park, Hsinchu 300, Taiwan  Tel.: +886-3-578-0211. Fax: +886-3-577-6047 www.realtek.com
  CONTENT ENVIRONMENTAL .............................................................................................................................. 3 OPERATING .................................................................................................................................................... 3 STORAGE ........................................................................................................................................................ 3 MTBF CALCULATION ..................................................................................................................................... 3 WARNING ............................................................................................................................................ 3 Federal Communication Commission Interference Statement ............................. 3 Industry Canada Statement ................................................................................................... 5 NCC 警語 ......................................................................................................... 13 Japan Statement ................................................................................................. 13 Korea Statement ................................................................................................ 14
    ENVIRONMENTAL  Operating Operating Temperature:  0°C to +70 °C Relative Humidity:  5-90% (non-condensing)  Storage Temperature:  -40°C to +80°C (non-operating) Relevant Humidity:  5-95% (non-condensing) MTBF calculation Over 150,000hours   Warning Federal Communication Commission Interference Statement  This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.  This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may  cause  harmful  interference  to  radio  communications.  However,  there  is  no  guarantee  that interference  will  not  occur  in  a  particular  installation.  If  this  equipment  does  cause  harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:  - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help.  This  device  complies with Part 15 of the FCC Rules.  Operation  is  subject  to  the  following  two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.  FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.
  FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.  Information To The OEM Integrator This module is approved only for  OEM integration in qualified laptop  and tablet computers and must  not  be  co-located  or  transmit  simultaneouslywith  any  other  antenna  or  transmitter.  The grantee  is  responsible  for  ensuring  all  OEM  implementations  satisfy  RF  exposure  and  other conditions for the compliance to all the rules that apply to the product into which this certified RF module is integrated. Additional testing and certification are necessary when all conditions are not satisfied. For all products market in US, OEM has to limit the operation channels in CH1 to CH13 for 2.4GHz band by supplied firmware programming tool. OEM shall not supply any tool or info to  the  end-user  regarding  to  Regulatory  Domain  change.  The OEM  should  also  inform  the  end users that operations in the 5.15-5.25GHz band are restricted to indoor usage only.  For  FCC  Part  15.31  (h)  and  (k):  The  host  manufacturer  is  responsible  for  additional  testing  to verify compliance as a composite system.  When testing the host device for compliance with Part 15 Subpart B, the host manufacturer is required to show compliance with Part 15 Subpart B while the transmitter module(s) are installed and operating. The modules should be transmitting and the evaluation  should  confirm  that  the  module’s  intentional  emissions  are  compliant  (i.e. fundamental  and  out  of  band  emissions).  The  host  manufacturer  must  verify  that  there  are  no additional unintentional emissions other than what is permitted in Part 15 Subpart B or emissions are complaint with the transmitter(s) rule(s).    For RF Exposure requirements:  The host manufacturer must also verify that the module continues to  comply  with  the  FCC  RF  exposure  limits.  Preliminary  assessment  is  normally  required  to determine if Class I or Class II permissive change requirements apply.   Antenna Information: Only the same or equivalent-type antennas as shown below may be used with this module. Other un-equivalent-type  antennas  may  require  additional  authorization  for  operation.  The  equivalent-type means the same antenna type that results in similar in-band and out-of-band radiation patterns.  For incorporation in Mobile devices (the distance from the antenna to the user >20cm):  Brand Model Name Antenna Type Connector Gain (dBi) 2.4GHz 5GHz LYNwave ALA110-222050-300011 PIFA Antenna IPEX MHF4 3.5 5 REALTEK RTK-ANT-0006 PIFA Antenna IPEX MHF4 3.5 5 PSA RFDPA171320EMLB301 Dipole Antenna IPEX MHF4 3.14 5  For incorporation in Laptop and Tablet platform (the distance from the antenna to the user according to OEM installation requirements):  Brand Model Name Antenna Type Connector Gain (dBi) 2.4GHz 5GHz REALTEK RTK-ANT-0006 PIFA Antenna IPEX MHF4 3.5 5
  Antenna Placement Within the Laptop and Tablet Host Platform: This module is authorized for installation in  qualified laptops (i.e. notebooks and netbooks), and tablets  with  overall  diagonal  dimension  of  the  keyboard  and/or  display  section  is  >  20  cm.  To ensure  RF  exposure  compliance  the  antenna(s)  used  with  this  module  must  be  installed  in  host platforms to provide a minimum separation distance, in all operating modes and orientations of the host platform. The separation distance is measured from the antenna and the outer surface of host platform in all directions for portable exposure conditions. The antenna separation distance applies to both horizontal and vertical orientation of  the antenna when installed in the host system. This module  must  not  be  co-located  with  any  other  RF  modules  or  transmitters.  Additional  SAR evaluation would be required if other RF modules or transmitters are co-located with this module. The required minimum separation distance for the antenna placement is outlined below:  For antenna located in the keyboard section of Laptop platform: ≥ 5 mm from the antenna to the bottom surface of keyboard section.  For antenna located in the display section of Laptop platform: ≥ 5 mm from the antenna to the bottom surface of keyboard section.  For antenna located in Tablet platform: ≥ 10 mm from all surfaces and edges of the tablet.  This  module  is  not  approved  for  installation  in  hosts  with  multiple  or  additional  transmitters. Additional FCC equipment approval is required for installation in such hosts.
  User Manual Of The End Product: The  end  user  has  to  be  informed  that  the  FCC  radio-frequency  exposure  guidelines  for  an uncontrolled environment can be satisfied. The end user has to also be informed that any changes or  modifications  not  expressly  approved  by  the  manufacturer  could  void  the  user's  authority  to operate this equipment.   Label Of The End Product: The final end product must be labeled in a visible area with the following  "Contains FCC ID: TX2-RTL8821CE".  The following FCC part 15.19 statement has to also be available on the label:  "This  device  complies  with  Part  15  of  FCC  rules.  Operation  is  subject  to  the  following  two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation." Industry Canada Statement  This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference and (2) this device must accept any interference, including interference that may cause undesired operation of the device  French translation: Le  présent  appareil  est  conforme  aux  CNR  d'Industrie  Canada  applicables  aux  appareils  radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) le dispositif ne doit pas produire de brouillage préjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu, y compris un brouillage susceptible de provoquer un fonctionnement indésirable.  CAN ICES-3(B)/NMB-3(B)  IC Radiation Exposure Statement: This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment.  French translation: Exposition  à  l'exposition  au  rayonnement  IC:  Cet  équipement  est  conforme  aux  limites d'exposition au rayonnement du CI établies pour un environnement non contrôlé.
  Information To The OEM Integrator This  module  is  intended  only  for  OEM  integrator.  The  OEM  integrator  is  responsible  for  the compliance  to  all  the  rules  that  apply  to  the  product  into  which  this  certified  RF  module  is integrated. Additional testing and certification may be necessary when multiple modules are used.   French translation : Ce module est destiné uniquement aux intégrateurs OEM. L'intégrateur OEM est responsable de la conformité  à  toutes  les  règles  qui  s'appliquent  au  produit  dans lequel  ce  module  RF  certifié  est intégré.  D'autres  tests  et  certifications  peuvent  être  nécessaires  lorsque  plusieurs  modules  sont utilisés.  For all products market in Canada, OEM has to limit the operation channels in CH1 to CH13 for 2.4GHz band by supplied firmware programming tool. OEM shall not supply any tool or info to the  end-user  regarding  to  Regulatory  Domain  change.  Operations in  the  5.15-5.25GHz  band  are restricted to indoor usage only.  French translation : Pour tous les produits de marché au Canada, OEM doit limiter les canaux d'opération CH1 à CH13 pour la bande 2,4 GHz par l'outil de programmation fourni firmware. L'OEM ne doit fournir aucun outil ou information à l'utilisateur final concernant la modification du domaine réglementaire. Les opérations dans la bande 5.15-5.25GHz sont limitées à l'utilisation à l'intérieur seulement.  The  host  manufacturer  is  responsible  for  additional  testing  to verify  compliance  as  a  composite system.  When  testing  the  host  device  for  compliance  with  ICES-003,  the  host  manufacturer  is required  to  show  compliance  with  ICES-003  while  the  transmitter  module(s)  are  installed  and operating.  The  modules  should  be  transmitting  and  the  evaluation  should  confirm  that  the module’s intentional emissions are compliant (i.e. fundamental and out of band emissions). The host manufacturer must verify that there are no additional unintentional emissions other than what is permitted in ICES-003 or emissions are complaint with the transmitter(s) rule(s).    French translation: Le fabricant hôte est responsable de tests supplémentaires pour vérifier la conformité en tant que système  composite.  Lors  de  l'essai  du  dispositif  hôte  pour  la  conformité  avec  ICES-003,  le fabricant  hôte  doit démontrer la conformité  avec  ICES-003 pendant  que  le  module  émetteur  est installé et fonctionne. Les modules devraient transmettre et l'évaluation devrait confirmer que les émissions intentionnelles  du  module  sont  conformes  (c'est-à-dire  les  émissions  fondamentales  et hors  bande).  Le  fabricant  de  l'hôte  doit  vérifier  qu'il  n'y  a  pas  d'autres  émissions  non intentionnelles autres que celles autorisées dans la norme ICES-003 ou que les émissions sont une plainte avec la (les) règle (s) de l'émetteur.
  For RF Exposure requirements:  The host manufacturer must also verify that the module continues to  comply  with  the  ISED  RF  exposure  limits.  Preliminary  assessment  is  normally  required  to determine if Class I or Class II permissive change requirements apply.   French translation: Pour  les  exigences  d'exposition  RF:  Le  fabricant  hôte  doit  également  vérifier  que  le  module continue  à  se  conformer  aux  limites  d'exposition  RF  ISED.  Une  évaluation  préliminaire  est normalement nécessaire pour déterminer si des exigences de changement permissif de classe I ou de classe II s'appliquent.   Antenna Information: Only the same or equivalent-type antennas as shown below may be used with this module. Other un-equivalent-type  antennas  may  require  additional  authorization  for  operation.  The  equivalent-type means the same antenna type that results in similar in-band and out-of-band radiation patterns.  French translation: Informations sur l'antenne: Seules les antennes de même type ou équivalent comme indiqué ci-dessous peuvent être utilisées avec ce module. D'autres antennes de type non équivalent peuvent nécessiter une autorisation supplémentaire pour fonctionner. Le type équivalent signifie le même type d'antenne qui se traduit par des diagrammes de rayonnement intra-bande et hors bande.  For incorporation in Mobile devices (the distance from the antenna to the user >20cm) :  French translation: Pour l'incorporation dans les appareils mobiles (la distance de l'antenne à l'utilisateur> 20cm): Brand Model Name Antenna Type Connector Gain (dBi) 2.4GHz 5GHz LYNwave ALA110-222050-300011 PIFA Antenna IPEX MHF4 3.5 5 REALTEK RTK-ANT-0006 PIFA Antenna IPEX MHF4 3.5 5 PSA RFDPA171320EMLB301 Dipole Antenna IPEX MHF4 3.14 5  For incorporation in Laptop and Tablet platform (the distance from the antenna to the user <=20cm):  French translation: Pour l'incorporation dans la plate-forme d'ordinateur portable et de tablette (la distance de l'antenne à l'utilisateur <= 20cm): Brand Model Name Antenna Type Connector Gain (dBi) 2.4GHz 5GHz REALTEK RTK-ANT-0006 PIFA Antenna IPEX MHF4 3.5 5
  Antenna Placement Within the Laptop and Tablet Host Platform: This module is authorized for installation in  qualified laptops (i.e. notebooks and netbooks), and tablets  with  overall  diagonal  dimension  of  the  keyboard  and/or  display  section  is  >  20  cm.  To ensure  RF  exposure  compliance  the  antenna(s)  used  with  this  module  must  be  installed  in  host platforms to provide a minimum separation distance, in all operating modes and orientations of the host platform. The separation distance is measured from the antenna and the outer surface of host platform in all directions for portable exposure conditions. The antenna separation distance applies to both horizontal and vertical orientation of  the antenna when installed in the host system. This module  must  not  be  co-located  with  any  other  RF  modules  or  transmitters.  Additional  SAR evaluation would be required if other RF modules or transmitters are co-located with this module. The required minimum separation distance for the antenna placement is outlined below:  For antenna located in the keyboard section of Laptop platform: ≥ 5 mm from the antenna to the bottom surface of keyboard section.  For antenna located in the display section of Laptop platform: ≥ 5 mm from the antenna to the bottom surface of keyboard section.  For antenna located in Tablet platform: ≥ 10 mm from all surfaces and edges of the tablet.  French translation: Placement d'antenne dans la plate-forme d'ordinateur portable et de tablette: Ce module est autorisé pour l'installation sur les ordinateurs portables qualifiés (c.-à-d. Les ordinateurs portables et les netbooks) et les tablettes avec une dimension diagonale globale de la section du clavier et / ou de l'affichage sont> 20 cm. Pour assurer la conformité à l'exposition RF, l'antenne (s) utilisée (s) avec ce module doit être installée dans les plates-formes hôtes pour assurer une distance de séparation minimale, dans tous les modes de fonctionnement et les orientations de la plate-forme hôte. La distance de séparation est mesurée à partir de l'antenne et de la surface extérieure de la plate-forme hôte dans toutes les directions pour les conditions d'exposition portables. La distance de séparation de l'antenne s'applique à l'orientation horizontale et verticale de l'antenne lorsqu'il est installé dans le système hôte. Ce module ne doit pas être localisé avec d'autres modules RF ou transmetteurs. Une évaluation SAR supplémentaire serait requise si d'autres modules RF ou émetteurs sont co-implantés avec ce module. La distance de séparation minimale requise pour le placement de l'antenne est décrite ci-dessous:  Pour l'antenne située dans la section du clavier de la plate-forme de l'ordinateur portable: ≥ 5 mm de l'antenne à la surface inférieure de la section du clavier.  Pour l'antenne  située  dans  la  section  d'affichage  de  la  plate-forme  portable:  ≥ 5 mm de l'antenne à la surface inférieure de la section du clavier.  Pour  l'antenne  située  dans  la  plate-forme  Tablet:  ≥  10  mm  de  toutes  les  surfaces  et les bords de la tablette.
  Label Of The End Product: The final end product must be labeled in a visible area with the following  "Contains IC: 6317A-RTL8821CE" The  Host  Model  Number  (HMN)  must  be  indicated  at  any  location  on  the  exterior  of  the  end product or product packaging or product literature which shall be available with the end product or online.  French translation: ÉTIQUETTE DU PRODUIT FINAL: Le produit final doit être étiqueté dans une zone visible avec les   "Contient IC: 6317A-RTL8821CE" Le numéro de modèle hôte (HMN) doit être indiqué à tout endroit à l'extérieur du produit final ou de  l'emballage  du  produit  ou  de  la  documentation  du  produit  qui  doit  être  disponible  avec  le produit final ou en ligne.  User Manual Of The End Product: The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. The end user has to also be informed that any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment.   French translation: Manuel d'utilisation de la fin Produit: L'intégrateur OEM doit être conscient de ne pas fournir des informations à l'utilisateur final quant à la façon d'installer ou de supprimer ce module RF dans  le manuel de l'utilisateur du produit final qui  intègre  ce  module.  Le  manuel  de  l'utilisateur  final  doit  inclure  toutes  les  informations réglementaires requises et avertissements comme indiqué  dans ce manuel.
  Caution:  (i) the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems; (ii) the maximum antenna gain permitted for devices in the bands 5250-5350 MHz and 5470-5725 MHz shall comply with the e.i.r.p. limit; and (iii) the maximum antenna gain permitted for devices in the band 5725-5825 MHz shall comply with the e.i.r.p. limits specified for point-to-point and non point-to-point operation as appropriate. (iv) Users should also be advised that high-power radars are allocated as primary users (i.e. priority users) of the bands 5250-5350 MHz and 5650-5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices. (v) Dynamic Frequency Selection (DFS) for devices operating in the bands 5250-5350 MHz, 5470-5600 MHz and 5650-5725 MHz  French translation: Avertissement: Le guide d’utilisation des dispositifs pour réseaux locaux doit inclure des instructions précises sur les restrictions susmentionnées, notamment : (i) les dispositifs fonctionnant dans la bande 5 150-5 250 MHz sont réservés uniquement pour une utilisation à l’intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux; (ii) le gain maximal d’antenne permis pour les dispositifs utilisant les bandes 5 250-5 350 MHz et 5 470-5 725 MHz doit se conformer à la limite de p.i.r.e.; (iii) le gain maximal d’antenne permis (pour les dispositifs utilisant la bande 5 725-5 825 MHz) doit se conformer à la limite de p.i.r.e. spécifiée pour l’exploitation point à point et non point à point, selon le cas. (iv) De plus, les utilisateurs devraient aussi être avisés que les utilisateurs de radars de haute puissance sont désignés utilisateurs principaux (c.-à-d., qu’ils ont la priorité) pour les bandes 5 250-5 350 MHz et 5 650-5 850 MHz et que ces radars pourraient causer du brouillage et/ou des dommages aux dispositifs LAN-EL. (v) Sélection dynamique de fréquences (DFS) pour les dispositifs fonctionnant dans les bandes 5250-5350 MHz, 5470-5600 MHz et 5650-5725 MHz.  The device could automatically discontinue transmission in case of absence of information to transmit, or operational failure. Note that this is not intended to prohibit transmission of control or signaling information or the use of repetitive codes where required by the technology.  French translation: Le dispositif pourrait automatiquement cesser d'émettre en cas d'absence d'informations à transmettre, ou une défaillance opérationnelle. Notez que ce n'est pas l'intention d'interdire la transmission des informations de contrôle ou de signalisation ou l'utilisation de codes répétitifs lorsque requis par la technologie.
   NCC 警語 經型式認證合格之低功率射頻電機,非經許可,公司、商號或使用者均不得擅自變更頻率、加大功率或變更原設計之特性及功能。  低功率射頻電機之使用不得影響飛航安全及干擾合法通信;經發現有干擾現象時,應立即停用,並改善至無干擾時方得繼續使用。前項合法通信,指依電信法規定作業之無線電通信。低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。    本模組於取得認證後將依規定於模組本體標示審合格籤,並要求平台上標示 「本產品內含射頻模組:ID編號」            Japan Statement Host system must be labeled with "Contains MIC ID:xxxxxx“, MIC ID displayed on label. 5GHz band (W52, W53): Indoor use only.
   Korea Statement  B 급기기  (가정용 방송통신기자재) 이 기기는 가정용(B 급) 전자파적합기기로서 주로 가정에서 사용하는 것을 목적으로  하며,  모든 지역에서  사용할 수 있습니다.
 Installing the Wireless PCIe NGFF2230 module Hardware Installing PCIe NGFF2230 module to PCIe NGFF2230 connector and connect two external Wi-Fi antennas on I-PEX connectors.
     Un-installing the Wireless PCIe NGFF2230 module Hardware Remove 2 external Wi-Fi Antennas from the Wireless PCIe NGFF2230 module board and remove the Wireless PCIe NGFF2230 module board from PCIe NGFF2230 connector port
  Installing the Wireless PCIe NGFF2230 module  Software Before you proceed with the installation, please notice following descriptions. Note1: The following installation was operated under Windows 7. Note2: If you have installed the WLAN driver & utility before, please uninstall the old version first. A. Execute the “setup.exe”, Click “Next” to process the installation  B. Click “Install” to process the installation
     C. Click Install this driver software anyway  D. After step “C” please press Next button.
     E. Please click “YES” to install BT package.  F. Please click “下一步”to continue.
    G. Please click “下一步”to continue.
     H. Please click “安装”to start installation.  I. Please click “完成”to finish the installation.
        J. Press Finish button to complete the install process
  Un-installing the Wireless PCIe NGFF2230 module Software A. Uninstall the RTL8821CE WLAN Driver from “Start”→ “All Programs”→ “REALTEK 11ac 8821CE PCIE WLAN NIC Massproduction kit” Please click “Uninstall” to remove RTL8821CE WLAN driver.
    Installing the Bluetooth USB Module  Software A. Insert the NGFF2230 card into system connector. B. Boot on system then the “Geniric Bluttooth Adapter” device will show up in device manager. C. Click right button on “RT Bluetooth Radio” and select “Update Driver”.
 Page 24/29
   D. After select “Update Driver Software ” then the Hardware Update Wizard will pop up, please select “Browse my computer for driver software” and press Next button. E. After step “D” please Select “Let me pick from a list of device drivers on my computer ”.     Page 25/29
      F. Finish step “E” then select “Have Disk..”  G. Now select browse to find the driver for device and press Next button.(The driver’s locate is the same with WiFi driver )     Page 26/29
              Page 27/29
    H. Then click “Install this driver software anyway” to continue. I. Press close button to complete the install process and you can see the Driver will be show up in Device Manager.             Page 28/29
                                   Page 29/29

Navigation menu