Realtek Semiconductor RTU7010-DWAV31 DWA User Manual 1
Realtek Semiconductor Corp. DWA 1
User manual rev
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 767429 |
| Application ID | izpbLfDZI2ux8vgdULHsnQ== |
| Document Description | User manual rev |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 11.94kB (149287 bits) |
| Date Submitted | 2007-03-12 00:00:00 |
| Date Available | 2007-07-13 00:00:00 |
| Creation Date | 2007-03-12 13:57:11 |
| Producing Software | Acrobat Distiller 7.0 (Windows) |
| Document Lastmod | 2007-03-12 15:28:59 |
| Document Title | 1 |
| Document Creator | Acrobat PDFMaker 7.0 for Word |
| Document Author: | PY |
Realtek DWA User Guide.doc Realtek DWA User’s Guide Revision A Author : Robert Teng Date : 06/03/2007 Realtek Corp. All Rights Reserved by Realtek Corp. Realtek DWA User Guide.doc Table of Contents 1. Introduction .............................................................................. 3 2. System Description................................................................... 3 2.1. UWB PHY ....................................................................... 4 2.2. NEC MAC ....................................................................... 4 2.3. EEPROM ......................................................................... 4 3. Hardware Interfaces.................................................................. 5 3.1. USB Interface .......................................................................................... 5 4. Document History……………………………………………...5 5. Radiation Exposure Statement…………………………………5 6. Interference Statement …………………………………………6 7. Coordination Requirements………………………………….6 All Rights Reserved by Realtek Corp. Realtek DWA User Guide.doc 1. Introduction This document describes the operations, interfaces, schematic and layout of Rev. 2.1 of the NEC DWA Demo Board. The DWA is the hub function device to connect wired USB device with wireless USB host controller. If the upstream port is connected to host PC with USB cable, DWA worked as wired USB Hub device. If DWA upstream port isn’t connected to host PC, DWA can worked as wireless USB Hub device. 2. System Description The DWA supports the following functions: Compliant with USB2.0(max. data rate=480 Mbps) Supports for 4 downstream facing ports. Support full speed and low speed transaction on downstream facing. Supports switches to select associated hosts and LEDs to indicate connecting host. Support 53.3M, 80M, 106.7M, 160M, 200M, 320M, 400M, 480Mbps. The DWA system mainly consists of two main chips – (i) UWB PHY(RTU7010), (ii) NEC MAC(UPD720180). Up to two antennas can be supported by the UWB PHY for performance improvement. A serial EEPROM(256K) is required to store proper data/commands for the PHY chip and MAC chip. To make the system work properly, the EEPROM should be loaded with proper content by using the EEPROM utility provided by NEC. All Rights Reserved by Realtek Corp. Realtek DWA User Guide.doc The RF performance can also be tested using the test utility provided by NEC. Two basic clock frequencies are used in the system – 30MHz for MAC and 66MHz for PHY. Some more details of the components are shown in the following sections. The system block diagram is shown below. Figure 1 System Block Diagram 2.1.UWB PHY This chip integrates the RF and baseband functions of a UWB PHY defined by the standard. This version of PHY chip is packaged in 48-pin QFN form factor. The analog/RF section requires 1.8V and 3.3V to operate. The digital core operates with 1.5V and the I/O voltage can support a range of 1.8V~3.3V. 2.2. NEC MAC This MAC chip is from NEC which has a standard MPI interface to communicate with a standard UWB PHY, as well as a high speed USB interface(the upstream port) to connect directly to a PC. This chip requires voltages of 1.5V and 3.3V. 2.3. EEPROM This chip is a serial EEPROM from Atmel with a capacity of 256Kb. It is used by the MAC to store the initialization data and command sequence required by the MAC and PHY on start up. This chip requires 3.3V only. All Rights Reserved by Realtek Corp. Realtek DWA User Guide.doc 3. Hardware Interfaces 3.1. USB Interface Table 1 USB series “Mini-B” connector termination assignment Pin# Pin Name Description VBUS See USB specification D- See USB specification D+ See USB specification NC See USB specification GND See USB specification SHELL See USB specification 4. Document History Date 06/03/07 Revision Description Initial Release Author Robert Teng 5. Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This device may only be operated indoors. Operation outdoors is in violation of 47 U.S.C. 301 and could subject the operator to serious legal penalties. All Rights Reserved by Realtek Corp. Realtek DWA User Guide.doc 6. Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. CAUTION: Any changes of modifications not expressly approved by the grantee of this device could void the user’s authority to operate the equipment. 7. Coordination Requirements For real application, the transmitter will only be active when communicating with the specific receiver through handshaking, acknowledgement and other mechanisms over the wireless channel. All Rights Reserved by Realtek Corp.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No Encryption : Standard V2.3 (128-bit) User Access : Print Tagged PDF : Yes XMP Toolkit : 3.1-701 Producer : Acrobat Distiller 7.0 (Windows) Tag Email Subject : Demo board doc template Tag Author Email Display Name : Phil Yang Tag Author Email : phil.yang@wionics.com Tag Ad Hoc Review Cycle ID : 1267113708 Company : OMC Source Modified : D:20070312055700 Creator Tool : Acrobat PDFMaker 7.0 for Word Modify Date : 2007:03:12 15:28:59+08:00 Create Date : 2007:03:12 13:57:11+08:00 Metadata Date : 2007:03:12 15:28:59+08:00 Document ID : uuid:69ed8a88-a092-4f05-bb03-2a623c76cc36 Instance ID : uuid:8641baec-16a1-4fba-89f5-c680508a515f Version ID : 43 Format : application/pdf Title : 1 Creator : PY Subject : Headline : Page Count : 6 Page Layout : OneColumn Author : PYEXIF Metadata provided by EXIF.tools