Redline Communications AN50 Access Node User Manual AN 50 v19

Download:
Mirror Download [FCC.gov]
Document ID	254769
Application ID	7Of85lnwa6ATuRZNABZyYg==
Document Description	users manual 1
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	80.79kB (1009918 bits)
Date Submitted	2002-07-08 00:00:00
Date Available	2002-07-02 00:00:00
Creation Date	2002-06-13 11:15:15
Producing Software	Acrobat PDFWriter 5.0 for Windows NT
Document Lastmod	2002-06-13 11:15:44
Document Title	AN-50 User Manual v19.doc
Document Creator	AN-50 User Manual v19.doc - Microsoft Word
Document Author:	rhunter

ACCESS NODE - 50 USER GUIDE
USER
Guide
Access Node-50
Redline Communications Inc.
90 Tiverton Court
Suite 102
Markham, Ontario
Canada
L3R 9V2
AN-50 User Manual
Redline Access Node-50
USER
Guide
Version 19
Copyright Information
This document may not in whole or in part be copied, reproduced, or reduced to
any medium without prior consent, in writing, from Redline Communications.
Disclaimer
This user guide was designed to help you install, use and troubleshoot the Redline
AN-50 Fixed Wireless Access (FWA) PTP system. Every effort has been made
to ensure the accuracy of the material provided herein, however, Redline assumes
no responsibility regarding the use of the material. Additionally, Redline makes
no representations or warranties, either expressed or implied, regarding the
contents of this product. Redline Communications shall not be liable for any
misuse regarding this product.
If you have any comments or suggestions concerning this guide, please Email
them to: support@Redlinecommunications.com.
2/52
Redline Communications
…..solving the first mile challenge.
AN-50 User Manual
TABLE OF CONTENTS
1.
2.
3.
4.
Getting Started ........................................................................................................ 5
Important Safety Information .................................................................................. 6
Important Service Information................................................................................. 7
Unpacking the AN-50 System ................................................................................. 8
4.1. The AN-50 Terminal at a Glance ..................................................................... 8
4.2. The AN-50 Transceiver/Antenna at a Glance ................................................. 11
5. AN-50 Terminal Installation.................................................................................. 12
5.1. General Site Survey ....................................................................................... 12
5.2. Installing the Antenna .................................................................................... 14
5.3. Running the IF Cable ..................................................................................... 16
5.4. Install the Terminal........................................................................................ 17
6. System Configuration and Operation ..................................................................... 20
6.1. Home Page Screen......................................................................................... 20
6.2. Bridge Status Screen...................................................................................... 22
6.3. Configuration................................................................................................. 24
6.4. Upgrade......................................................................................................... 28
6.5. Change Password........................................................................................... 29
6.6. Log File ......................................................................................................... 30
7. Diagnostics and Troubleshooting........................................................................... 32
7.1. Diagnostics via the front panel....................................................................... 32
7.1.1.
System Power ........................................................................................ 33
7.1.2.
System Fault .......................................................................................... 33
7.1.3.
Wireless Link......................................................................................... 33
7.1.4.
Wireless Signal ...................................................................................... 34
7.1.5.
Ethernet Link ......................................................................................... 34
7.1.6.
Ethernet Collision .................................................................................. 35
7.2. Troubleshooting via the screen menu ............................................................. 35
7.2.1.
Home page does not appear.................................................................... 35
8. Fixed Wireless Access Primer ............................................................................... 37
8.1. Introduction ................................................................................................... 37
8.2. Who can benefit from the AN-50? ................................................................. 37
8.3. The UNII band advantage .............................................................................. 39
8.4. Wireless Facts................................................................................................ 41
8.4.1.
Link Budget ........................................................................................... 41
8.5. Deployment Scenarios ................................................................................... 47
8.5.1.
Co-located deployments. ........................................................................ 48
8.5.2.
Adjacent area deployments..................................................................... 48
9. AN-50 Specifications ............................................................................................ 52
3/52
Redline Communications
…..solving the first mile challenge.
AN-50 User Manual
LIST OF FIGURES
Figure 1 The AN-50 System out of the box. .................................................................... 8
Figure 2 Antenna/Transceiver close up.......................................................................... 11
Figure 3 AN-50 installation. .......................................................................................... 12
Figure 4 Antenna deployment options. .......................................................................... 14
Figure 5 Mounting the antenna on a building structure. ................................................. 15
Figure 6 Aligning the antenna. ...................................................................................... 16
Figure 7 AN-50 connected to switch/router ................................................................... 17
Figure 8 AN-50 connected to host computer.................................................................. 18
Figure 9 AN-50 connected to a hub. .............................................................................. 18
Figure 10 AN-50 LAN Ethernet Port pin-out................................................................. 18
Figure 11 AN-50 Home Page. ....................................................................................... 20
Figure 12 Username and password screen. .................................................................... 22
Figure 13 Bridge status screen....................................................................................... 22
Figure 14 Bridge configuration screen........................................................................... 25
Figure 16 Upgrade screen.............................................................................................. 28
Figure 17 Status of upgrade file transfer. ....................................................................... 29
Figure 18 Change Password Screen............................................................................... 29
Figure 19 Log File Screen. ............................................................................................ 30
Figure 20 Front panel status LEDs. ............................................................................... 32
Figure 21 Wireless Extension for Carriers. .................................................................... 38
Figure 22 Wireless Solution for ISPs............................................................................. 38
Figure 23. Wireless Solution for Enterprise. .................................................................. 39
Figure 24 Fresnel Zone obstruction. ............................................................................. 43
Figure 25 Fresnel zone radius calculation. ..................................................................... 43
Figure 26 Link Budget for 16 QAM ¾ code rate, 36 Mbps ........................................... 46
Figure 27 Fade margin graphs for LOS and NLOS........................................................ 46
Figure 29 Switched PTP configuration. ......................................................................... 48
Figure 30 Adjacent channel interference........................................................................ 48
Figure 31 Deployment Scenarios................................................................................... 49
LIST OF TABLES
Table 1 System Power Diagnostics................................................................................ 33
Table 2 Wireless Link Diagnostics. ............................................................................... 33
Table 3 Wireless Signal Diagnostics.............................................................................. 34
Table 4 Ethernet Link Diagnostics................................................................................. 34
Table 5 Ethernet Collision Diagnostics.......................................................................... 35
Table 6 Home Page Diagnostics. ................................................................................... 36
Table 7 Modulation and Data Rate Table...................................................................... 42
Table 8 Availability versus outage time......................................................................... 44
Table 9 Fade margin versus distance for 99.99% availability......................................... 44
Table 10 Radar horizon ranges for different terminal heights (H1 and H2). .................... 47
4/52
Redline Communications
…..solving the first mile challenge.
AN-50 User Manual
Getting Started
This user manual is designed to get you quickly started with the Redline Access
Node-50 Point to Point (PTP) Fixed Wireless Access (FWA) system. The AN-50
is a high performing Ethernet Bridge terminal system configurable to operate as a
high speed point to point link or switched point to point (S-PTP) system1,
providing the Industry’s first true low-cost and scalable multi-service platform to
support both backhaul and access functions from a common equipment
infrastructure and management system. The system can deliver a net data
throughput of up to 54 Mbps (72 Mbps raw), with a non-line of sight (NLOS)
capability to address challenging deployment scenarios.
The AN-50 operates in the unlicensed UNII band of 5.8 GHz and includes
patented technologies to address any potential inter-cell interference issues. The
system also features adaptive modulation in both directions for automatic
selection of modulation schemes, including BPSK, QPSK, 16 and 64 QAM, to
maximize spectral efficiency and hence increase revenue potential for a given
deployment scenario.
The AN-50 is equipped with a narrow beam antenna to provide high directivity
for long-range operations, beyond 50 km in line of sight (LOS) conditions, and up
to 10 km in NLOS.
The guide will help you with the following:
•
•
•
•
•
•
•
Unpacking the AN-50 System
Set-up and Connections
System Configuration and Operation
Trouble Shooting Tips
Understanding Fixed Wireless Access Systems
Glossary of Terms
AN-50 Specifications
Future software upgrade.
5/52
Redline Communications
…..solving the first mile challenge.
AN-50 User Manual
2.
Important Safety Information
Read the user’s manual and follow all operating and safety instructions.
Keep all information for future reference.
This product is supplied with a grounding power plug. Do not defeat this
important safety feature.
The power requirements are indicated on the product-marking label. Do not
exceed the described limits.
Replace the fuse with the correct type and current rating.
Position the power cord to avoid possible damage and do not overload wall
outlets.
Do not place this product on or near a direct heat source.
Do not operate this device near water or in a wet location.
Use only a damp cloth for cleaning. Do not use liquid or aerosol cleaners.
Disconnect power before cleaning.
10
Protect the unit by disconnecting the power during a lightning storm or if it is not
used for long periods of time.
11
Locate the AN-50 on a stable horizontal surface or securely mount it in a 19”
Telco rack.
12
The T-58 Series Transceiver unit must not be located near power lines or other
electrical power circuits.
13
The T-58 Series Transceiver units must be properly grounded to protect against
power surges and accumulated static electricity. It is the user’s responsibility that
this device is installed in accordance with Section 810 of the National Electrical
Code, ANSI/NFPA No. 70-1984 or Section 54 of the Canadian Electrical Code.
These codes describe correct installation procedures for grounding of the
transceiver unit, mast, lead in wire and discharge unit, location of discharge unit,
size of grounding conductors and connection requirements for grounding
electrodes. It is recommended that the installation of a transceiver unit be
contracted to a professional installer.
6/52
Redline Communications
…..solving the first mile challenge.
AN-50 User Manual
3.
Important Service Information
Refer all repairs to qualified service personnel. Do not remove the covers or
modify any part of this device.
Disconnect the power to this product and return for it for service, if the following
conditions apply:
a) The unit does not function by following the operating instructions outlined in
the user’s manual.
b) Liquid has been spilled, an object is inside or rain has been exposed to the AN50 Access Node unit.
c) The product has been dropped or the housing is damaged.
d) The power cord or plug is damaged.
Ensure that only parts that are specified by the product manufacturer are used for
replacement.
NOTICE
1 - This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provided reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.
2 - A Class A digital device is marketed for use in a commercial, industrial or business
environment, exclusive of a device which is marketed for use by the general public or is
intended to be used in the home.
3 - Changes or modifications not expressly approved by Redline Communications Inc.
could void the user’s authority to operate the equipment.
7/52
Redline Communications
…..solving the first mile challenge.
AN-50 User Manual
4.
Unpacking the AN-50 System
The AN-50 product comes packaged with the following items (refer to Figure 1
for a pictorial view):
•
•
•
•
•
AN-50 Terminal (indoor unit)
Transceiver mounted to Antenna (outdoor units)
Antenna mounting Kit
Power Cord and IF Cable (100 ft)
User manual
Transceiver/
Antenna
AN-50 Terminal
Antenna
Mount
C able
C able
Power/IF
Cables
User Manual
Figure 1 The AN-50 System out of the box.
4.1.
The AN-50 Terminal at a Glance
The front panel of the AN-50 terminal comprises three main status indicators:
System, Wireless, and Ethernet and a LAN interface.
a) System
The system portion of the front panel features a reset switch, and two LEDs; Pwr
and Fault, as shown in the figure below. Note, at power on, all LEDs will light
for a brief moment to indicate the LEDs are properly functioning.
8/52
Redline Communications
…..solving the first mile challenge.
AN-50 User Manual
Reset – A paper clip, or similar object, can be used to reset the system by
depressing the “Reset” button recessed in the front panel. The reset button is used
to reactivate the terminal in the event that it is functioning improperly or is in a
state of suspension. Depressing the reset button for more than 5 seconds will
restore the unit’s operating system back to the last successfully loaded software
revision.
Pwr – The “Pwr LED” lights solid and green when the AC power is properly
applied to the terminal. In the event the power fails or the cord is disconnected,
the “Pwr LED” light will not illuminate.
Fault – The “Fault LED” will light solid and red when a serious fault is detected
within the system. If this occurs, depress the “Reset” button for more than 5
seconds to try to restore the terminal. If the problem persists, then contact the
Redline support line.
B) Wireless
The wireless portion of the front display contains two LEDs, one for the Link and
the other for Signal, as shown below.
Link – The “Link” LED lights solid and green when the communication link to
the remote terminal is functioning properly at the specified data rate (refer to the
Configuration section for details regarding data rate). The LED will flash green
when the system operates at a lower data rate.
When the link is compromised, the LED stops illuminating.
9/52
Redline Communications
…..solving the first mile challenge.
AN-50 User Manual
Signal – The “Signal” LED flashes in amber when signal errors are detected due
to degradation in the communication link.
C) Ethernet
The Ethernet portion of the front panel display comprises four main LEDs,
including Link, 100, FD and Col, as shown below.
Link – The “Link” illuminates solid and green when the Local Arean Network
(LAN) connection to the remote terminal is functioning properly.
100 – The “100” LED lights solid and green when the Ethernet port is operating
at 100 Mb/s. The LED will not illuminate if the port is operating in 10 Mb/s
mode. Note the Ethernet port automatically selects the speed through autonegotiation with either the host computer/server or router/switch.
FD – The “FD” LED illuminates solid and green when the LAN connection is
operating in Full Duplex mode. The LED will not illuminate if the system is
operating in Half Duplex mode. The system automatically selects the duplex
mode through auto-negotiation with the host computer or switch.
Col – The “Col” LED flashes in amber when collisions occur in the LAN traffic.
D) LAN Interface
The LAN interface is an Ethernet port, also known as a 10BaseT port, which is
used to connect the AN-50 to either the core network or to a host computer. A
router or switch will likely be used to complete the connection to the core
network, as shown in the next figure.
10/52
Redline Communications
…..solving the first mile challenge.
AN-50 User Manual
To Core
Network
CAT 5
STP
Cable
Third Party
Switch/Router
The rear of the terminal comprises two interfaces; the power cord interface, and
F-Type female connector to which the IF cable attaches.
4.2.
The AN-50 Transceiver/Antenna at a Glance
The AN-50 transceiver is mounted to the back of the flat plate antenna, as shown
in Figure 2. The antenna features a bracket to mount onto a 1-inch pole.
Transceiver
Flat
Plate
Antenna
Pole
Mounting
Bracket
Front
View
Back
View
Figure 2 Antenna/Transceiver close up.
The pole is approximately three (3) feet in length and features a curve profile to
facilitate protruding building infrastructures, such as eaves. A mounting bracket
at the bottom of the pole is used to attach the antenna to sides of buildings or onto
other poles of varying diameters.
Before connecting the AN-50 system, it is important to review the important
safety tips provided in the beginning of this manual.
11/52
Redline Communications
…..solving the first mile challenge.
AN-50 User Manual
5.
AN-50 Terminal Installation
This section describes the easy steps to follow to install the AN-50 terminal and
associated equipment. A Class A digital device that is marketed for use in a commercial,
industrial or business environment.
Figure 3 illustrates the three primary cables that are required to complete the
installation including; Power, IF and CAT 5 (not included). The power cord
connects to a standard North American 120 VAC power outlet, the IF cable
connects the terminal (located indoors) to the transceiver (located outdoors), and
the CAT 5 which connects the terminal to a switch or router for interface to the
core network.
Transceiver
Flat Plate
Antenna
CAT 5 Cable
Terminal
Antenna
Pole and
Mount
AC Power
Chord
IF Cable
Figure 3 AN-50 installation.
The terminal is for indoor installation only while the transceiver and antenna are
mounted externally. The principal steps in installation are:
1.
2.
3.
4.
Conduct a general site survey
Install the antenna
Run the IF cable
Install the terminal
Each step is addressed in more detail below.
5.1.
General Site Survey
The first step in installing the AN-50 system is to conduct a general site survey.
Although the installation steps are relatively straightforward, they do involve
12/52
Redline Communications
…..solving the first mile challenge.
AN-50 User Manual
some construction and electrical work, which can be best performed by
professional installers.
The following site survey steps should be followed:
Determine the optimum location: The first key step in the deployment exercise
is to determine and identify building candidates that can be used to support the
PTP link. A critical parameter to consider is the range at which the two terminals
are required to operate. Range performance is determined by empirical formulas
that consider a number of equipment and environmental factors described in
Section 8 of this manual. Ensure that the installation sites meet the above range
performance requirements before moving to the next step. There are a number of
cell planning tools available in the market today, which make use of topographic
data to help with the cell planning.
Obtain a copy of the facility blueprints and verify their accuracy. The
installation process will require penetrating the building to run the IF cable
between the outdoor and indoor units. In this regard, it is imperative that the
blueprints of the building are up to date and accurate.
Identify a Clear Line of Sight Path. For maximum performance, it is
recommended to mount the antenna in a location where there is line of sight to the
remote terminal. If possible, the antenna should be positioned such that there is
maximum clearance within the first Fresnel zone of the direct path. Refer to
Section 8 for a full description of Fresel zone clearance and its impact on signal
propagation. The best means of achieving Fresnel zone clearance is to mount the
antennas as high as possible, on either a tall building or tower, as shown in Figure
4. Although the system is designed to operate in obstructed line of sight (NLOS)
conditions, as a result of the OFDM technology it incorporates, LOS deployments
provide much greater throughput capability.
13/52
Redline Communications
…..solving the first mile challenge.
AN-50 User Manual
Transceiver
Deployments
Figure 4 Antenna deployment options.
Identify potential sources of RF interference. Measure for any possible RF
interference on the roof-top or tower by utilizing a RF power meter or spectrum
analyzer. RF interference arises from any other wireless system operating within
the same frequency band of the AN-50. Note that the AN-50 can operate in any
one of the four channels designated for UNII band, therefore, there is some
flexibility in addressing or avoiding the interference should other transmitters, in
relatively close proximity, pose a problem.
Verify the location of access points. With the remote terminal transmitting, use a
spectrum analyzer to ensure there is adequate signal strength arriving at the
candidate location for the antenna.
5.2.
Installing the Antenna
Once the site survey has been completed, and the exact location of the antenna
identified, the next step is to mount the AN-50 transceiver/antenna onto either a
building structure or pole. The antenna and mounting brackets have been designed
to withstand strong winds (see specifications at the end of this user guide). It is
imperative that all bolts and nuts are securely fastened to avoid any movement
that could introduce misalignment. Note that there is an arrow on the back of the
antenna, which must be pointing upwards to indicate proper orientation when the
antenna is deployed.
14/52
Redline Communications
…..solving the first mile challenge.
AN-50 User Manual
Orientation
Arrow
For building mounts, ensure the surface to which the mounting bracket will be
attached is flat and vertical (use a level). Install the bracket using four lag screws,
with washers. There are two center holes that can be used to mount the bracket
onto a 2x4 stud. Make sure the surface to which the bracket is attaching is
structurally sound and can withstand the specified wind loading.
Lag Screw
and Washer
Figure 5 Mounting the antenna on a building structure.
Once the antenna is mounted, it has to be aligned in both the azimuth and
elevation planes. The elevation alignment is accomplished by loosening the two
bolts attached to the mounting bracket, as shown in Figure 6, and slanting the pole
until the antenna is aligned in elevation towards the remote terminal. The azimuth
alignment is achieved by loosening the two bolts on the antenna bracket, and
rotating the antenna until alignment is achieved.
15/52
Redline Communications
…..solving the first mile challenge.
AN-50 User Manual
Elevation
Adjustment
Adjustment
Bolts
Azimuth
Adjustment
Figure 6 Aligning the antenna.
Note that the antenna can also be mounted onto another pole separate from the
one supplied with the system. Contact Redline for different antenna mounting
options.
5.3.
Running the IF Cable
The system is equipped with a 100 foot of RF cable to interconnect the transceiver
and terminal. The following steps define the cable installation:
1. Run the cable through the antenna pole as shown below. Add extra cable
length to produce a drip-loop, as shown, to prevent water from
accumulating onto the connector. The IF cable is equipped with 75 ohm
F-type connectors at both ends, however, it is important to note that one
end of the cable is designated for outdoors, as it is a specialized weather
proof design, while the other end is to be connected to the indoor terminal
unit. A label is attached to one end of the cable to clearly indicate the
connector that is intended for outdoors. Make certain the ‘Outdoor’ label
is attached to the end of the cable that you plan to connect to the radio.
IF
Cable
Cable
Drip-Loop
2. Connect the F-type male connector from the cable to the female connector
attached to at the bottom of the transceiver. Note the connector at the top
end of the transceiver is connected via cable to the antenna itself.
16/52
Redline Communications
…..solving the first mile challenge.
AN-50 User Manual
3. Run the cable into the building by drilling a hole in the wall, where you
want the RG-6 to enter, or through an existing conduit. Local codes
require, at a minimum, that a ground cable be used, with a grounding
block installed as close as possible to the point of cable entry. An
optional lightning arrester may be used to protect the terminal and other
indoor equipment from sudden electrical surges. There are a variety of
choices for lightning arresters – it is recommended to use a professional
installer to determine the optimized solution.
4. Once inside the building, connect the cable to the F-type female
connector located on the back of the terminal.
5.4.
Install the Terminal
Once the IF cable is connected, the terminal is ready to be installed and
configured. The first step is to connect a CAT 5 cable from the Ethernet port to
the host IP appliance. Note a CAT 3 cable can be used if the terminal operates in
10BT mode (10 Mb/s data rate). However, even with 10BT connections today, it
is recommended to use CAT 5 cabling initially in anticipation for the increased
speed in the future. As noted previously, the data rate is determined automatically,
depending on the type of IP device connected to the system.
If the terminal is used for connection to a core network, then the IP appliance is
likely to be a router or switch as shown in Figure 7. In this configuration, a crossover Ethernet cable is required.
Third Party
Switch/Router
Host
Computer
To Core
Network
Figure 7 AN-50 connected to switch/router
For the remote terminal, the AN-50 may be connected directly to the host
computer, as shown in Figure 8. In this configuration, a straight-through Ethernet
cable is required.
17/52
Redline Communications
…..solving the first mile challenge.
AN-50 User Manual
Host
Computer
Figure 8 AN-50 connected to host computer.
The remote terminal may also be connected to a simple hub, for distribution to
several computers in a local network configuration, as shown in Figure 9. If the
terminal is connected to simple, hub, then a cross-over cable is required.
Third Party
Hub
Host
Computer
Host
Computer
Figure 9 AN-50 connected to a hub.
Figure 10 provides an illustration of the pin-out designation for the AN-50 LAN
interface, to help you establish other implementations that are not addressed in
this manual.
Figure 10 AN-50 LAN Ethernet Port pin-out.
Now connect the AC cord to the 120 VAC outlet and turn the terminal on using
the toggle switch at the rear of the unit. The system “Pwr” LED should illuminate
green to indicate proper power to the unit. If this LED is not on and/or the “Fault”
LED illuminates red, then there is a problem with the unit. Refer to the
diagnostics section, Section 7 on page 32, for further details on how to address
system faults. The system is now ready to be configured.
18/52
Redline Communications
…..solving the first mile challenge.
AN-50 User Manual
NOTICE
1 - The Model AN-50 is used as a fixed, point-to-point device that required to be
professionally installed by Redline Communications Inc. or trained professional
sub-contractors.
2 - For Compliance with FCC RF Exposure Requirements, the transmitting
antenna is required to be mounted outdoor on the building roof or antenna tower
and located at a safety distance of more than 1.5 meters (5 feet) from the
transmitting antenna to any person's body
3 - The Model AN-50 is a fixed, point-to-point device that is certified by FCC and
Industry Canada with the 5.8 GHz Directional Antennas, Models MT-486001 (28
dBi Gain) and MT-485002 (23 dBi)
19/52
Redline Communications
…..solving the first mile challenge.
AN-50 User Manual
6.
System Configuration and Operation
This section describes the procedures for configuring and operating the AN-50
terminal. All communication to the AN-50 is achieved over the Ethernet port,
using Hypertext transfer protocol (HTTP). This offers the advantage of allowing
the operator to access and control the AN-50 remotely from any geographical
location, providing the operator at the remote site has access to the Internet. It is
important to note, for the initial set-up, the operator must connect the host
computer locally to the AN-50 as shown in Figure 8.
Although the procedures to configure the AN-50 are relatively straightforward,
some familiarity with basic computer networks and administration would be
helpful.
6.1.
Home Page Screen
The first step is to log onto the AN-50 home page from a web browser, such as
Microsoft Internet Explorer, by typing in the system’s IP address. The system’s
default address (from the manufacturer) is 192.168.25.2, which will take you to
the screen shown in Figure 11.
Figure 11 AN-50 Home Page.
If the screen does not match the illustration in the figure, then check for possible
entry errors and retype if necessary, otherwise refer to the diagnostics section,
Section 7, for further assistance.
20/52
Redline Communications
…..solving the first mile challenge.
AN-50 User Manual
The home page main menu includes the following selections:
•
•
•
•
•
Home Page
Status
Configuration
Change Password
Log File
Located to the right of the main menu is a summary of general information related
to the configuration and status of the local unit. This page only presents
information, and does not accept inputs from the user. Data, shown on this screen,
is entered via the Configuration screen, described later. The following is a brief
description of each field in the General Information screen:
Device Name is the name of the device specified by the user. The name
can consist of any combination of letters or numbers.
Connected: Yes indicates the terminal is communicating properly to the
distant terminal. No indicates there is no communication with the distant
terminal.
Rate: Indicates the current data throughput of the system. With adaptive
modulation, this data rate may change over time, depending on the
prevailing propagation conditions.
Master: Indicates if the system is serving as the master or slave. Note that
in a point-to-point link only one AN-50 terminal can be the master.
Ethernet MAC address: Specifies the Ethernet address of the local host
computer or server.
IP Address: Specifies the IP address of the local host computer or server.
Netmast: Sets the IP network mast for the local host computer or server.
Gateway: Specifies the local gateway IP address.
Note that a password is required to enter into any of the following user screens:
•
•
•
Configuration
Upgrade
Change Password
21/52
Redline Communications
…..solving the first mile challenge.
AN-50 User Manual
An example of the username and password screen is shown in Figure 12. The
default value (set from the factory) for both username and password is ‘admin’.
Refer to the Change Password screen to change this value for future sessions.
Also, note that the User Name cannot be changed from admin.
Figure 12 Username and password screen.
6.2.
Bridge Status Screen
Clicking on Status in the main menu will bring up the Bridge Status screen. This
screen provides a status on General Info, Ethernet LAN statistics and Wireless
Statistics, as shown in Figure 13.
Figure 13 Bridge status screen.
22/52
Redline Communications
…..solving the first mile challenge.
AN-50 User Manual
General Info: Identical to the information found on the home page, with the
addition of Frequency, which represents the operating channel of the link. The
system can be configured to operate over 9 distinct channels, as described below.
Ethernet LAN Statistics:
Rx packets: Counts the number of packets successfully received by the
local system.
Rx packets - discarded: Counts the number of packet errors received by
the local system.
Tx packets: Counts the number of Ethernet packets transmitted by the
local system.
Wireless Statistics:
Received Signal Strength – min: Indicates the minimum received signal
strength measured over time.
Received Signal Strength – mean: Indicates the average received signal
strength received, averaged over time.
Received Signal Strength – max: Indicates the maximum received signal
strength measured over time.
Average SINADR: Indicates the average signal to noise ratio measured
over time. The ratio is based on the digital information provided from the
output of the A/D converter.
Rx bytes: Indicates the total number of bytes received over the air.
Rx bytes - discarded: Indicates the number of bytes with errors received
over the air from the remote terminal.
Rx packets: Indicates the number of packets received over the air from the
remote terminal.
Rx packets - retransmitted: Indicates the number of packets retransmitted
over the air from the remoter terminal.
Rx packets - discarded: Indicates the number of packets, originating from
the remote terminal that is lost over the air due to degradation in the RF
link.
23/52
Redline Communications
…..solving the first mile challenge.
AN-50 User Manual
Tx bytes: Indicates the total number of bytes transmitted over the air.
Tx bytes - discarded: Indicates the number of bytes with errors transmitted
over the air to the remote terminal.
Tx packets: Indicates the number of wireless packets (including Ethernet
frames and error correction bytes) transmitted over the air by the local
terminal.
Tx packets - retransmitted: Indicates the number of packets retransmitted
over the air by the local terminal. The retransmission scheme is based on
the Acknowledge/Request (ARQ) algorithm that detects when packets are
lost and makes a request to the MAC scheduler to repeat transmission of
the lost packets.
Tx packets - discarded: Indicates the total number of packets lost over the
air due to degradation in the RF link.
6.3.
Configuration
The configuration page provides a simple to use Graphical User Interface (GUI)
for the operator to input the complete set of system parameters for both the
Ethernet and Wireless components of the AN-50 unit (refer to ). To store the
parameters into memory, press the ‘Save Configuration’ button from the bottom
of this page. This operation will be recorded into the ‘Log file’.
The Ethernet configuration includes the following fields:
Ethernet Configuration:
Device name: The device name is an alphanumeric identifier for the local
terminal, which can consist of any combination of letters and numbers.
The default name for the AN-50 system from the factory is set to WEB01.
The device name remains with the system, even during power off states,
until the operator re-types a new name using this menu field.
24/52
Redline Communications
…..solving the first mile challenge.
AN-50 User Manual
Figure 14 Bridge configuration screen.
IP address: This field is used to provide an IP address for the local AN-50
terminal. The default address from the factory is 192.168.25.2. For the
initial set-up, the terminal should not be connected to the Internet network,
i.e. the host computer should be connected directly to the terminal
Ethernet port, to avoid address conflicts with other devices in a public
network. Once the IP address has been set, the terminal can be connected
to the core network, where it can receive either static or dynamic
addressing (DHCP) in future configuration updates.
Netmask: This field is used by the operator to set the desired network
mask. The netmask value is typically set to "255.255.255.0 (Class C
subnet), which prevents certain local devices from going out into the
wireless network.
Gateway: This field is used to specify the IP address of the gateway with
which the AN-50 is communicating through the core network.
25/52
Redline Communications
…..solving the first mile challenge.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Modify Date                     : 2002:06:13 11:15:44-07:00
Create Date                     : 2002:06:13 11:15:15-07:00
Title                           : AN-50 User Manual v19.doc
Author                          : rhunter
Creator                         : AN-50 User Manual v19.doc - Microsoft Word
Producer                        : Acrobat PDFWriter 5.0 for Windows NT
Page Count                      : 25

EXIF Metadata provided by EXIF.tools