Renishaw plc RMP60V2 sensor for machine tools User Manual H 2000 5219 05 A RMP60 UG EN cvr

Download:
Mirror Download [FCC.gov]
Document ID	631737
Application ID	uMRU8ELmq7mlKNkv8eKG5Q==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	65.14kB (814201 bits)
Date Submitted	2006-02-27 00:00:00
Date Available	2006-04-07 00:00:00
Creation Date	2006-01-13 10:36:37
Producing Software	Acrobat Distiller 6.0.1 (Windows)
Document Lastmod	2006-01-13 10:40:49
Document Title	H-2000-5219-05-A (RMP60) {UG} [EN] cvr
Document Creator	Adobe PageMaker 7.0
Document Author:	dc0080

Installation and user’s guide
H-2000-5219-05-A
RMP60 - radio machine probe
© 2006 Renishaw. All rights reserved.
Disclaimer
This document may not be copied
or reproduced in whole or in part,
or transferred to any other media or
language, by any means, without the
prior written permission of Renishaw.
Considerable effort has been made to ensure
that the contents of this document are free
from inaccuracies and omissions. However,
Renishaw makes no warranties with respect
to the contents of this document and specifically
disclaims any implied warranties. Renishaw
reserves the right to make changes to this
document and to the product described herein
without obligation to notify any person of such
changes.
The publication of material within this
document does not imply freedom
from the patent rights of Renishaw plc.
Trademarks
RENISHAW® and the probe emblem used in
the RENISHAW logo are registered trademarks
of Renishaw plc in the UK and other countries.
apply innovation is a trademark of Renishaw
plc.
RENISHAW® is a registered trademark of
Renishaw plc in the UK and other countries.
Renishaw Part no: H-2000-5219-05-A
Issued: 01.06
All brand names and product names used in this
document are trade names, service marks,
trademarks, or registered trademarks of their
respective owners.
Contents
Contents
EC declaration of conformity ........................... 2
FCC declaration ............................................... 3
Safety ............................................................... 3
Installation and User’s guide ........................... 4
Typical probe system with
radio transmission ........................................... 5
System performance ....................................... 6
Operating envelope ......................................... 8
RMP60 dimensions ......................................... 9
Stylus weak link ............................................. 10
Operating mode ............................................. 11
Probe settings ................................................ 12
Multiple probe mode ...................................... 14
Reviewing current probe settings .................. 16
Changing probe settings ............................... 18
RMP60-RMI partnership ................................ 22
RMP60 batteries ............................................ 24
Battery life expectancy .................................. 26
RMP60 shank mounting ................................ 28
Stylus on-centre adjustment .......................... 29
Stylus trigger force and adjustment .............. 30
Diaphragm replacement ................................ 31
RMP60M system ........................................... 33
RMP60M dimensions .................................... 34
RMP60M screw torque values ...................... 35
Fault finding ................................................... 36
Parts list ......................................................... 41
Probe settings record table .......................... 44
2
EC DECLARATION OF CONFORMITY
Renishaw plc declares that the product:
Name:
RMP60/RMP60M
Description:
Radio machine probe
has been manufactured in conformity with the following standard:
BS EN 61326:1998/
Electrical equipment for measurement,
control and laboratory use - EMC requirements.
Immunity to annex A - industrial locations.
Emissions to class A - (non-domestic) limits.
and that it complies with the requirements of directive (as amended):
89/336/EEC
Electromagnetic compatibility
The above information is summarised from the full EC declaration
of conformity. A copy is available from Renishaw on request.
Radio approvals
3
FCC DECLARATION (USA)
FCC Section 15.19
This device complies with Part 15 of the FCC rules.
Operation is subject to the following two conditions:
1.
This device may not cause harmful interference.
2.
This device may accept any interference
received, including interference that may cause
undesired operation.
FCC Section 15.105
This equipment has been tested and found to
comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC rules. These limits
are designed to provide reasonable protection
against harmful interference when the equipment
is operated in a commercial environment.
This equipment generates, uses , and can radiate
radio frequency energy and, if not installed and
used in accordance with the instruction manual, may
cause harmful interference to radio communications.
Operation of this equipment in a residential area is
likely to cause harmful interference, in which case
you will be required to correct the interference at
your own expense.
FCC Section 15.21
The user is cautioned that any changes or
modifications not expressly approved by Renishaw
plc, or authorised representative could void the
user’s authority to operate the equipment.
SAFETY
Information for the user
Beware of unexpected movement. The user
should remain outside of the full working
envelope of probe head/extension/probe
combinations.
Handle and dispose of batteries in according to
the manufacturers recommendations. Use only
the recommended batteries. Do not allow the
battery terminals to contact other metallic
objects.
In all applications involving the use of machine
tools or CMMs, eye protection is recommended.
Refer to the machine supplier’s operating
instructions.
Information for the machine supplier
It is the machine supplier’s responsibility to
ensure that the user is made aware of any
hazards involved in operation, including those
mentioned in Renishaw product documentation,
and to ensure that adequate guards and safety
interlocks are provided.
Under certain circumstances the probe signal
may falsely indicate a probe seated condition.
Do not rely on probe signals to stop the
machine’s movement.
4
Installation and user’s guide
Installation and user’s guide
Warranty
Care of the probe
Equipment requiring attention under warranty
must be returned to your supplier. No claims
will be considered where Renishaw equipment
has been misused, or repairs or adjustments
have been attempted by unauthorised persons.
Keep system components clean and treat
the probe as a precision tool.
Changes to equipment
Renishaw reserve the right to change
specifications without obligation to change
equipment previously sold.
CNC machine
CNC machine tools must always be operated
by competent persons in accordance with
manufacturers instructions.
Patent notice
Features of products shown in this guide,
and of related products, are the subject of the
following patents and/or patent applications:
EP
EP
EP
EP
EP
EP
EP
JP
JP
JP
JP
0390342
0652413
0695926
1373995
142550
1457786
2,945,709
3,126,797
2004-522,961
2004-279,417
2005-502,035
US
US
US
US
US
US
WO
WO
5,040,931
5,212,872
5,279,042
5,669,151
6,941,671 B2
2003-01799097
2004-057552
2004-090467
Typical probe system with radio transmission
Typical probe system with radio transmission
CNC machining centre spindle
RMI
interface
RMI
mounting bracket
RMP60
inspection probe
Probe status LEDs
CNC
machine
control
Typical tool setting probe
Stylus
Cable
Workpiece
A workpiece set-up and inspection probe is
in effect another tool in the system. A probing
cycle may be included at any stage of the
machining process.
Optional
power supply unit
Optional
power supply unit
Interface unit
Probe data is transmitted from the RMP60
(or RMP60M) to the RMI via the radio link.
The RMI converts probe signals into a form
compatible with the machine CNC control.
6
System performance
System performance
RMP60 and RMP60M have identical user options and radio performance
Operating envelope
Radio transmission does not require line-of sight
and will pass through very small gaps and
machine tool windows. This allows easy
installation, either inside or outside the machine
enclosure.
Coolant and swarf residue accumulating on the
RMP60/M and RMI may have a detrimental
effect on transmission performance. Wipe clean
as often as is necessary to maintain unrestricted
transmission.
When operating, do not touch either the RMI
cover or the probe glass window with your hand,
as this will affect the performance.
Operation in extremes of temperature will result
in some reduction in range.
RMI position
The probe system should be positioned so that
the optimum range can be achieved over the full
travel of the machine axes. Always face the front
cover of the RMI in the general direction of the
machining area and the tool magazine, ensuring
both are within the operating envelope.
To assist in finding the optimum position of the
RMI, the signal quality is displayed on an RMI
signal LED.
Note: RMP60/M in radio-on configuration
The RMP60/M has a built-in hibernate mode
(battery saving mode) that saves battery life
when the RMI is unpowered in radio-on
(radio-off or time-off) configurations.
The RMP60/M goes into hibernate 30 seconds
after the RMI is unpowered (or the RMP60 is
out of range).
When in hibernate, the RMP60/M checks for a
powered RMI every 30 seconds. If found, the
RMP60/M goes from hibernate to standby,
ready for radio-on.
System performance
Probe repeatability
Environment
Maximum 2 Sigma (2σ) value.
Repeatability of 1.0 µm (40 µ in) is valid for a
test velocity of 480 mm/min (1.57 ft/min) at the
stylus tip, using a stylus 50 mm (1.97 in) long.
RMP60 IP rating
IPX8
RMP60 weight
(without shank)
Without batteries
With batteries
855 g (30.16 oz)
901 g (31.79 oz)
RMP60M weight
(without shank)
Without batteries
With batteries
690 g (24.34 oz)
736 g (25.95 oz)
Max spin speed
RMP60
1000 rev/min
RMP60M
Dependent on configuration
RMP60
RMP60M
RMI
Temperature
Storage
-10 °C to 70 °C
(14 °F to 158 °F)
Normal
operating
5 °C to 50 °C
(41 F° to 122 °F)
Operating envelope
Operating envelope
RMP60 probe + RMI
Always face the front cover of the RMI in the
general direction of the machining area and
the tool magazine, ensuring both are within
the operating envelope.
RMP60 and RMI must be within each other’s
operating envelope. The operating envelope
shows line-of-sight performance, however radio
transmission does not require line-of-sight as
long as any reflected radio path is less than
the 15 m (49.2 ft) system operating range
75°
Range metres (feet)
OPERATING AND SWITCH ON/OFF
75°
75°
60°
60°
45°
15 (49)
60°
45°
10 (33)
45°
30°
30°
5 (16)
30°
15°
15°
0°
0°
(16)
15°
30°
15°
30°
10
(33)
45°
45°
60°
75°
15
(49)
75°
90°
60°
15°
5 (16)
0°
15°
10 (33)
30°
45°
60°
15 (49)
75°
RMP60 dimensions
RMP60 dimensions
Ø63 (Ø2.48)
50 (1.97)
19 (0.75)
dimensions mm (in)
Battery cassette
Shank switch
(optional)
M4 stylus
18°
18°
RMP60 window
Status LEDs
76 (2.99)
Bobbin
alignment dot
STYLUS OVERTRAVEL LIMITS
Stylus length
±X / ±Y
50 (1.96)
21 (0.82)
11 (0.43)
100 (3.93)
37 (1.45)
11 (0.43)
A range of probe
ready shanks
are available
from Renishaw
10
Stylus with weak link
Stylus weak link
Must be used with steel styli.
For optimum metrology performance, do not use
the weak link with ceramic or carbon fibre styli.
Fitting stylus with weak link onto RMP60
In the event of excessive stylus overtravel,
the weak link is designed to break, thereby
protecting the probe from damage.
Take care to avoid stressing the weak link
during assembly.
Fitting a weak link
2 Nm (1.7 lbf.ft)
Removing a broken weak link
5 mm AF
2 Nm (1.7 lbf.ft)
12 mm
(0.47 in)
Operating mode
Operating mode
LEDs
flashing
green
LEDs
flashing
red
PROBE STATUS LEDs
LED colour
➤
➤
X /Y
LEDs
flashing
red
➤
Probe status
Flashing
green
Probe seated in
operating mode
Flashing
red
Probe triggered in
operating mode
Flashing
green
and blue
Probe seated in
operating mode
- low battery
Flashing
red and
blue
Probe triggered in
operating mode
- low battery
Constant
red
Battery dead
Rapid
flashing
red
Extremely dead
alkaline batteries
or unsuitable
lithium thionyl
chloride batteries
Graphic hint
11
12
Probe settings
Probe settings
The RMP60 probe can be in one of three modes:
Stand-by mode - The RMP60 is waiting for a
switch on signal.
Operating mode - Activated by one of the
switch on methods described on this page.
In this mode the RMP60 is now ready for use.
Configuration mode - The trigger logic
configuration method allows the following
settings to be configured.
Switch-on / switch-off methods
The following switch on / switch off options
can be configured:
1. Radio on / Radio off
2. Radio on / Timer off
3. Spin on / Spin off
4. Spin on / Timer off
5. Shank switch on / Shank switch off
Note:
The RMP60 will be switched on after 1 second
in all modes.
After being switched on, the RMP60 must be
on for 1 second minimum (7 seconds for spin
start) before being switched off.
Probe settings
Switch-on method
Switch-off methods available
Radio on
Radio switch on when
commanded by an M code.
Radio off
Radio switch off when commanded by an M code.
13
A timer automatically switches the probe off after 90 minutes
from the last trigger if not turned off by an M code.
Timer off (time out)
Time out will occur (12, 33 or 134 seconds) after the last probe
trigger or reseat.
Spin on
Spin at 650 rev/min for
1 second minimum (6 seconds
maximum).
Spin off
Spin at 650 rev/min for 1 second minimum (6 seconds
maximum).
A timer automatically switches the probe off after 90 minutes
from the last trigger if not spun.
Timer off (time out)
Time out will occur (12, 33 or 134 seconds) after the last probe
trigger or reseat.
Shank switch on
Shank switch off
14
Multiple probe mode
Multiple probe mode
RMP60 can be user configured using trigger
logic to allow multiple RMP60s to be used
with a single RMI.
Note:
Radio turn on cannot be used in multiple probe
mode.
Only one of the multiple probes per machine
will need partnering as, by configuring multiple
probes to a single ‘mode-on’ choice, all probes
have the same identification. The probe to be
partnered, is partnered after selection of
multiple probe on in ‘Changing probe settings’.
There is no limit to the number of probes that
can be used with a single RMI as long as they
all have the same ‘mode-on’ colour choice.
All RMP60s are factory-set to ‘mode off’.
To allow multiple probes/single RMI in close
proximity, 16 choices of ‘mode-on’ colours are
available – each representing a different
machine tool installation. The choices are
shown on the next page and in ‘Changing
probe settings’.
All probes on a single RMI machine should be
set to the same ‘mode-on’ colour choice; any
multiple probes on adjacent machines should
all be set to an alternative ‘mode-on’ colour
choice. Multiple probe mode will not appear in
the configuration of the probe if radio turn on
has been selected.
The addition of further probe(s) into a single
probe installation requires all probes to be
re-configured to the same multiple probe
‘mode-on’ choice and the repartnering of
one of the probes to the installed RMI.
The addition of further probes (or replacements)
into a multi probe installation is achieved simply
by reconfiguration to the same ‘mode-on’
colour choice.
Note:
Any number of RMP60s set to ‘mode-off’ can
be used alongside RMP60s set to ‘Multiple
probe mode’.
Multiple mode settings table
MULTIPLE PROBE MODE
MODE OFF
Deflect
stylus
< 4 sec
to cycle
to next
setting
MODE ON
MACHINE 1
MACHINE 2
MACHINE 3
MACHINE 4
MACHINE 5
MACHINE 6
MACHINE 7
MACHINE 8
MACHINE 9
MACHINE 10
MACHINE 11
MACHINE 12
MACHINE 13
MACHINE 14
MACHINE 15
MACHINE 16
Return to MODE OFF
15
16
Reviewing current probe settings
Reviewing current probe settings
1. Insert batteries, or if already inserted remove
for 5 seconds and replace.
2. DO NOT deflect the stylus when reviewing
settings.
3. The LEDs will show the following sequence.
LED CHECK
SWITCH-ON METHOD
RADIO ON
SHANK ON
SPIN ON
(omitted if Multiple Probe
Mode was selected)
or
continued on next page
or
Reviewing current probe settings
SWITCH-OFF METHOD
(omitted for shank-on)
RADIO OFF
or SPIN OFF
SHORT TIME OUT
MEDIUM TIME OUT
12 sec
33 sec
or
LONG TIME OUT
134 sec
or
or
MULTIPLE PROBE MODE (omitted for radio-on)
(see ‘Multiple probe mode’ to view all 16 choices)
MODE ON
MODE OFF
MACHINE 1
or
MACHINE 2
MACHINE 16
or
BATTERY STATUS
BATTERY GOOD
BATTERY LOW
or
PROBE IN STAND-BY MODE (after 5 sec)
17
18
Changing probe settings
Changing probe settings
Probe settings can be configured using the
trigger logic.
4. To exit the trigger logic at any point, leave
the stylus undeflected for over 20 seconds.
1. Insert the batteries, or if already inserted,
remove for 5 seconds and replace.
5. Settings record table
2. Deflect the stylus and hold deflected until
5 red flashes occur at end of the review
sequence.
Note:
If battery power is low then each of the
5 red flashes will be followed by a blue flash.
See ‘Probe settings’ for further details.
3. The probe will now be in the configuration
mode and the current switch on method will
flash. The probe settings can be changed as
shown below.
Note:
Settings are saved as they are changed
For quick reference, Renishaw suggest
that you record your settings in the table
at the back of this guide.
These settings will be needed if the probe
is replaced.
Changing probe settings
TO CHANGE SWITCH-ON METHOD
RADIO ON
(omitted if Multiple Probe
Mode was selected)
Deflect
stylus
<4s
SHANK ON
Deflect
stylus
<4s
SPIN ON
Deflect stylus < 4 seconds
Deflect stylus > 4 seconds
TO CHANGE SWITCH-OFF METHOD
(omitted if shank turn on was selected)
RADIO
or
SPIN
Deflect
stylus
<4s
SHORT
TIME OUT
12 s
Deflect
stylus
<4s
MEDIUM
TIME OUT
33 s
Deflect stylus < 4 seconds
Deflect stylus > 4 seconds
Deflect
stylus
<4s
LONG
TIME OUT
134 s
19
20
Changing probe settings
ACQUISTION MODE
Deflect
stylus
<4s
ACQUISITION MODE
OFF
ACQUISITION MODE
ON
Note: After the RMI
has been acquired, the
RMP60 will only show
Acquistion Mode Off.
See RMP60 - RMI
partnership.
Deflect stylus < 4 seconds
Cease triggering here, unless the
multiple probe mode is required
in which case
Deflect stylus > 4 seconds
Changing probe settings
21
MULTIPLE PROBE MODE
(see “Multiple probe mode” to view all 16 choices)
MODE ON
MODE OFF
Deflect
stylus
<4s
MACHINE 1
Deflect
stylus
<4s
MACHINE 2
MACHINE 16
Deflect stylus < 4 seconds
Deflect stylus > 4 seconds
ACQUISTION MODE
ACQUISITION MODE
OFF
Deflect
stylus
<4s
ACQUISITION MODE
ON
Note: After the RMI
has been acquired, the
RMP60 will only show
Acquistion Mode Off.
See RMP60 - RMI
partnership.
Deflect stylus
> 4 seconds
Deflect stylus < 4 seconds
Return to
TO CHANGE SWITCH-ON METHOD
22
RMP60-RMI partnership
RMP60-RMI partnership
System setup is achieved using trigger logic and
powering on the RMI.
1. Use trigger logic to access the RMP60
configuration mode.
Trigger logic is a method that allows user
configuration of the options available in the
RMP60. Trigger logic uses a sequence of
RMP60 triggering and battery insertion followed
by further RMP60 triggering.
2. Configure the turn on method (if not
configured).
This leads the user through a series of choices,
allowing selection of the required options.
Reviewing of choices can be made by battery
insertion alone. See Reviewing probe settings.
3. Configure the turn off method (if not
configured).
4. Enter the acquisition mode by deflecting
the stylus.
5. Remain in ‘Acquisition Mode Off’ by not
releasing the stylus. This allows time to get
the RMI ready for partnering.
To partner an RMP60 and RMI
Partnering is only required during initial system
set-up. Further partnering is only required if
either the RMP60 or RMI is changed.
Partnering will not be lost by reconfiguration
of probe settings or when changing batteries.
Partnering can take place anywhere within the
operating envelope.
6. Power on the RMI.
7. Watch the RMI signal LED; after a couple
of seconds the LED will repeatedly flash on
and off green. This is the start of a 10
second interval in which the RMI is in
acquisition mode.
continued on next page
RMP60-RMI partnership
8. Release the RMP60 stylus and trigger it a
couple of times. This causes the RMP60 to
go into (and out of) acquisition mode.
9. The RMI signal LED will change to
repeatedly flashing red and yellow (for the
remainder of the 10 second interval),
indicating a successful partnering.
10. Leave the RMP60 for 20 seconds to go
into standby.
11. The system is ready to use.
23
Note
To check that turn on and off settings have not
accidentally been changed, remove and insert
batteries to review the current probe settings.
Note
When holding the RMP60, do NOT wrap a
hand, or anything else, around the glass
window.
Note
When the RMP60 and RMI become partners
the RMI records the RMP60 identity. It is not
possible for an RMI to be partnered with more
than one RMP60 in ‘Standard Mode’ - see
Multiple Probe Mode.
It is possible for an RMP60 to be partnered
with more than one RMI, but the system will
not function correctly.
24
RMP60 batteries
RMP60 batteries
Replacing batteries
Only use specified batteries.
Clean and dry the RMP60 with a cloth or paper
towel before removing the battery cover. Where
the RMP60 has been exposed to coolant, it is
recommended that the area around the battery
cover is cleaned.
To access the RMP60 batteries, remove the
battery cover by rotating the securing screw 30°
anticlockwise and withdraw the battery cassette.
Take care to avoid damaging the cover gasket.
When inserting the batteries, ensure they are
loaded as shown (see next page).
If one or more batteries are incorrectly loaded
the probe will not respond.
Do not mix new and used batteries or battery
types, as this will result in reduced life and
damage to the batteries.
Always ensure that the cover gasket and mating
surfaces are clean and free from damage before
reassembly.
25
RMP60 batteries
Battery cassette
Batteries 2 x AA
DO NOT leave exhausted batteries in probe
DO NOT allow coolant or debris to enter
the battery compartment
DO check for correct battery polarity
Please dispose of exhausted batteries
in accordance with local regulations.
Do not dispose of batteries in fire.
Battery life expectancy
26
Battery life expectancy
Typical battery life
Using standard alkaline batteries at 5 % usage,
typically the probe will continue to operate for
approximately 1 week after a low battery
warning is first indicated.
Replace the batteries as soon as is practicable.
BATTERY
Two
AA type
SHANK/SPIN TURN ON
After batteries are inserted into the RMP60,
the LEDs will indicate the current settings.
In order to achieve the stated radio turn-on life
(stand-by or 5% usage), the RMP60 must
be in range of its powered partner RMI.
RADIO TURN ON
CONTINUOUS
USE
STAND-BY
LIFE
(days - typical)
5% USAGE
72 min/day
(days - typical)
STAND-BY
LIFE
(days - typical)
5% USAGE
72 min/day
(days - typical)
(hours - typical)
Alkaline
650
100
130
65
140
LTC
1,300
200
260
130
280
LTC (Lithium Thionyl Chloride)
Battery life expectancy
27
Low battery indicator
The low battery warning will be signalled by
the alternate blue flashing of the probe status
LED when the end of the usable battery life
is approaching. Simultaneously, the low battery
LED on the RMI will be lit.
Dead battery indicator
When the battery voltage drops below the
threshold where performance can no longer
be guaranteed, the RMP60 probe status LED
will change to constant red, followed by flashing
red.
Battery specification
The RMP60 requires two identical AA size
batteries, individually rated at a voltage of
between 1.2 V and 3.6 V.
The standard batteries are AA alkaline.
Alternative batteries are lithium thionyl
chloride (3.6 V), Nickel Cadmium (NiCd) or
Nickel Metal Hydride (NiMh).
Rechargeable batteries: either Nickel Metal
Hydride (NiMh) or Nickel Cadmium (NiCd)
can be used. Expect a battery life of
approximately 50% of alkaline figures.
For applications requiring maximum battery
life, a high capacity lithium thionyl chloride
type is essential.
Sources for lithium thionyl chloride
batteries
Please use these specified part numbers only
Supplier
RS
Radio Shack
Part number
596-602, 201-9438,
23-037
Manufacturer
Saft
Part number
LS 14500
Sonnenschein
SL 760/S
Tadiran
TL-5903/S, TL-2100/S
Xeno
XL-060F
28
RMP60 shank mounting
RMP60 shank mounting
Probe to shank alignment dot
(used when bobbin is fitted)
Stage 1 RMP60 shank mounting
If the RMP60 is not to be used with a shank
switch, proceed from step 3.
1. Remove the plug from the rear of the
RMP60 using pliers.
Bobbin
Rear plug
2. Place the bobbin into the shank.
3. Fully slacken the four screws A.
4. Grease the two screws B, and fit into the
shank.
5. Fit the RMP60 onto the shank, and visually
position it central relative to the shank.
6. Partially tighten screws B to 2 - 3 Nm
(1.5 - 2.2 lbf.ft).
(If the RMP60 is NOT to be on-centre adjusted,
fully tighten screws B to 6-8 Nm (4.4 - 5.9 lbf ft).
The RMP60 assembly is ready for use.
For on-centre adjustment, complete steps 7-10
(see next page).
Shank switch
(optional)
Note :
1. During adjustment, care should be taken
NOT to rotate the probe relative to the shank,
as damage to the shank switch bobbin may
occur (if fitted).
2. If a probe on a shank is accidentally
dropped, it should be checked for on-centre
position.
3. Do NOT hit or tap the probe to achieve
on-centre adjustment.
Stylus on-centre adjustment
29
Stylus on-centre adjustment (if required)
Stage 2
On-centre adjustment
7. Each of the four screws A will move the
probe relative to the shank, in the X or Y
direction, as pressure is applied.
Tighten individually, backing off after each
movement.
SHANK
4 mm AF
2.5 mm AF
8. When the stylus tip run-out is less than
20 µm, fully tighten screws B to 6 - 8 Nm
(4.4 - 5.9 lbf.ft).
9. For final centering, use screws A to move
the RMP60, progressively slackening on one
side and tightening the opposite screw, as
the final setting is approached, using two
hexagon keys.
Tip run out of 5 µm (0.0002 in) should be
achievable.
10. It is important that all four screws A are tight
or tightened to 1.5 - 3.5 Nm (1.1 - 2.6 lbf.ft)
once the final setting has been achieved.
PROBE
30
Stylus trigger force and adjustment
Stylus trigger force and adjustment
Spring force within the probe causes the stylus to sit in a unique
position, and return to this position following each stylus deflection.
Stylus trigger force is set by Renishaw. The user should only
adjust the trigger force in special circumstances, e.g. excessive
machine vibration or insufficient force to support the stylus weight.
To adjust the trigger force, turn the adjusting screw anticlockwise
to reduce force (more sensitive) or clockwise to increase
force (less sensitive). A stop prevents damage, which
could be caused by over-tightening the adjusting screw.
Reduce
force
Stylus trigger force
Z direction
5.30 N / 530 gf (18.69 ozf)
X/Y direction (50 mm stylus)
X/Y trigger forces vary, depending on trigger direction.
There are 3 high force and 3 low force X/Y directions:
2 mm AF
Factory setting for low force direction = 0.75 N / 75 gf (2.6 ozf)
Factory setting for high force direction = 1.4 N / 140 gf (4.9 ozf)
Maximum setting for low force direction = 2 N / 200 gf (7.0 ozf)
Maximum setting for high force direction = 3.5 N / 350 gf (12.3 ozf)
Minimum setting for low force direction = 0.5N / 50 gf (1.7 ozf)
Minimum setting for high force direction = 0.9 N / 90 gf (3.2 ozf)
Increase
force
Diaphragm replacement
31
Diaphragm replacement
RMP60 DIAPHRAGMS
OUTER DIAPHRAGM INSPECTION
The probe mechanism is protected from coolant
and debris by two diaphragms. These provide
adequate protection under normal working
conditions.
1. Remove the stylus.
The user should periodically check the outer
diaphragm for signs of damage. If this is evident,
replace the outer diaphragm.
The user must not remove the inner diaphragm.
If damaged, return the probe to your supplier.
2. Undo the three M3 front cover screws and
remove the front cover.
3. Inspect the outer diaphragm for damage.
4. To remove the outer diaphragm, grip by the
outer edge and pull off.
INNER DIAPHRAGM INSPECTION
5. Inspect the inner diaphragm for damage.
If damaged return the probe to your supplier.
DO NOT REMOVE THE INNER DIAPHRAGM
AS THE WARRANTY WILL BE VOID.
32
Diaphragm replacement
OUTER DIAPHRAGM REPLACEMENT
6. Fit the new diaphragm over centre.
7. Locate the outer edge of the diaphragm to
rest on the outer edge of the inner
diaphragm.
M3 screw
2.5 mm AF
1 Nm
(0.74 lbf.ft)
8. Refit the front cover and the M3 screws.
Cover
9. Refit the stylus and re-calibrate the probe.
Outer
diaphragm
Inner
diaphragm
33
RMP60M system
RMP60M system
LPE extension bar
RMP60M is a special modular version
of RMP60. It enables probe inspection
of part features inaccessible to RMP60,
by fitting selected adaptors and
extensions as shown.
LP2 probe
RMP60M
LP2 adaptor
M4
stylus
RMP60M
module
MA4 90°
adaptor
M4 stylus
see parts list
RMP60M extension
RMP60M probe module
RMP60M dimensions
RMP60M dimensions
66,25
(2.61)
50,00 / 100,00 / 150,00
(1.97) / (3.94) / (5.91)
40,75
(1.60)
50,50
(1.99)
Ø63,00
100,00 / 150,00 / 200,00
(3.94) / (5.91) / (7.88)
(Ø2.48)
Ø25,00
(Ø0.98)
Ø63,00
66,25
(2.61)
Ø63,00
dimensions mm (in)
(Ø2.48)
12,50 (0.49)
(Ø2.48)
34
RMP60M screw torque values
35
RMP60M screw torque values
2,6 Nm
(1.92 lbf.ft)
10 Nm - 12 Nm
(7.37 lbf.ft - 8.84 lbf.ft)
2,6 Nm
(1.92 lb. ft)
2,6 Nm
(1.92 lbf.ft)
36
Fault-finding
Fault finding - If in doubt, consult your probe supplier.
Sympton
Cause
Action
RMP60 fails to switch on.
Dead batteries.
Change batteries.
Batteries incorrectly
inserted.
Check/change batteries.
Probe out of range
Check position of RMI,
see Operating envelope.
No RMI ‘start/stop’ signal
(radio-on mode only)
Check RMI for green start LED.
Incorrect spin speed
(spin switch on only).
Check spin speed.
Malfunctioning shank switch
(shank switch mode only).
Check switch operation.
Incorrect switch on method
configured.
Check configuration and alter
as required.
Incorrect Multiple Probe Mode
setting configured
Check configuration and alter
as required.
RMP60 in hibernate mode
(radio-on mode only).
Ensure probe is in range
and wait up to 30 seconds.
Check position of RMI,
see Operating envelope.
Fault-finding
37
Symptom
Cause
Action
RMP60 fails to switch off.
Incorrect switch off method
configured.
Check configuration and alter as
required.
No RMI ‘start/stop’ signal
(radio on mode only)
Check RMI for green start LED.
Probe in time out mode and
placed in tool magazine and is
being triggered by movement.
Review use of time out mode.
Increase spring force.
Malfunctioning shank switch
(shank switch mode only).
Check switch operation.
Incorrect spin speed
(spin switch on only).
Check spin speed.
RMP60 status LEDs
continuous red.
Dead batteries.
Change batteries.
Poor battery life.
Radio link failure – RMP out
of RMI range.
Check position of RMI,
see Operating envelope.
RMI power has been removed.
Check power to RMI, leave
RMI powered all the time.
Local radio interference.
Identify source and move it
away from the RMP60 and RMI.
38
Fault-finding
Symptom
Cause
Action
Probe crash.
Inspection probe using
tool setting probe signals.
Review program.
Review installation.
Probe length offset
missing/incorrect.
Review probe software.
Workpiece obstructing probe
path.
Review program.
Radio link failure – RMP60
out of RMI range.
Check position of RMI,
see Operating envelope.
RMP60 has been
enclosed/shielded by metal.
Review installation.
RMP60 and RMI are not
partnered.
Partner RMP60 and RMI.
Dead batteries.
Change batteries.
RMP60 status LEDs do
not correspond to RMI
status LEDs.
RMP60 probe status
LED continually lit red.
Fault-finding
Symptom
Cause
Action
RMI error LED lit during
probing cycle.
Probe timed out.
Change setting.
Review turn off method.
Check position of RMI,
see Operating envelope.
Probe out of range.
RMI error LED illuminated
during intended probe cycle.
Probe not switched on.
Probe out of range.
Check configuration and
alter as required.
Check position of RMI,
see Operating envelope.
RMI low battery LED lit.
Low batteries.
Change batteries soon.
Reduced range.
Local radio interference.
Identify and move.
Poor repeatability.
Probing occurs within
machine’s acceleration/
deceleration zones.
Review probe software.
Probe feedrate too high.
Check feedrate and correct,
test at different speeds.
Temperature variation.
Minimise temperature change.
Calibrate more frequently.
Calibrate just before use.
Wear in machine tool.
Perform health check on
machine.
39
40
Fault-finding
Symptom
Cause
Action
Poor measurement
results.
Debris on part or stylus.
Clean and recalibrate.
Repeatability of probe
into spindle.
Verify by repeated toolchange
and single point move.
Loose probe to shank
mounting or stylus.
Check and tighten as
required, recalibrate.
Offsets not being updated.
Review software.
Calibrated feature has moved.
Check.
Measurement occurs as
stylus leaves surface.
Review software.
Calibration and probing
speeds different.
Review software.
Parts list
Parts list - Please quote the Part no. when ordering equipment.
Type
Part no.
Description
RMP60
A-4113-0001
RMP60 probe with batteries, tool kit and user’s guide
(set to radio on/radio off).
Battery
P-BT03-0005
AA batteries - Alkaline - supplied as standard with probe
(two required).
Battery
P-BT03-0008
AA batteries - Lithium thionyl chloride (two required).
Stylus
A-5000-3709
PS3-1C ceramic stylus 50 mm long with Ø6 mm ball.
Weak link kit
A-2085-0068
Weak link (Part no. M-2085-0069 (x 2) and
5 mm AF spanner.
TK
A-4038-0304
Probe tool kit comprising: Ø1.98 mm stylus tool,
2.0 mm AF hexagon key 2.5 mm AF hexagon key (x 2),
4 mm AF hexagon key, shank grub screws (x 2),
weak link and 5 mm AF spanner.
Diaphragm kit
A-4038-0302
RMP60 outer diaphragm.
Battery cassette
A-4038-0300
RMP60 battery cassette assembly.
Cassette seal
A-4038-0301
Battery cassette housing seal.
41
42
Parts list
Type
Part no.
Description
Bobbin
A-4038-0303
Bobbin for shank switch.
RMI
A-4113-0050
RMI, side exit, with 15 m (49.2 ft) cable, tool kit and
User’s guide.
Mtg brkt
A-2033-0830
Mounting bracket with fixing screws, washers and nuts.
Styli
—
For complete listing, please see Renishaw Styli guide.
Part no. H-1000-3200.
Software
tools
—
For complete listing of Renishaw software for machine,
please see data sheets. Part no. H-2000-2289 and
H-2000-2298.
Shanks
—
For complete listing, please see Renishaw data sheet
H-2000-2011.
Parts list
Type
Part no.
Description
RMP60M module
A-4113-1003
RMP60M module with batteries, tool kit and User’s guide.
(set to radio on/radio off).
Extension L100
A-4038-1010
RMP60M extension - 100 mm long.
Extension L150
A-4038-1027
RMP60M extension - 150 mm long.
Extension L200
A-4038-1028
RMP60M extension - 200 mm long.
Probe module
A-4038-1002
RMP60M probe module assembly.
RMP60M/LP2
A-4038-0212
RMP60M LP2 adaptor assembly
LPE1
A-2063-7001
LPE1 extension bar - 50 mm long.
LPE2
A-2063-7002
LPE2 extension bar - 100 mm long.
LPE3
A-2063-7003
LPE3 extension bar - 150 mm long.
MA4
A-2063-7600
MA4 90° adaptor assembly.
43
Probe settings record table
Switch-on method
Radio on
Shank on
Spin on
Switch-off method
Radio or spin
Short timeout
12 seconds
Medium timeout
33 seconds
Long timeout
134 seconds
Multiple probe mode
Off (factory set)
On (machine number)
RMP60 serial no.
--------------------------------------------------------------------------
✔ tick
44
Renishaw plc
New Mills, Wotton-under-Edge,
Gloucestershire, GL12 8JR
United Kingdom
T +44 (0)1453 524524
F +44 (0)1453 524901
E uk@renishaw.com
www.renishaw.com
For worldwide contact details,
please visit our main web site at
www.renishaw.com/contact
*H-2000-5219-05*

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 47
Has XFA                         : No
XMP Toolkit                     : XMP toolkit 2.9.1-14, framework 1.6
About                           : uuid:981c741d-3eba-4f03-a917-934d0f793da8
Producer                        : Acrobat Distiller 6.0.1 (Windows)
Keywords                        : 
Creator Tool                    : Adobe PageMaker 7.0
Modify Date                     : 2006:01:13 10:40:49Z
Create Date                     : 2006:01:13 10:36:37Z
Metadata Date                   : 2006:01:13 10:40:49Z
Document ID                     : uuid:0dd18a30-e753-40aa-94a5-18d79d4949d5
Format                          : application/pdf
Title                           : H-2000-5219-05-A (RMP60) {UG} [EN] cvr
Creator                         : dc0080
Description                     : H-2000-5219-05-A (RMP60) {UG} [EN] cvr
Author                          : dc0080
Subject                         : H-2000-5219-05-A (RMP60) {UG} [EN] cvr

EXIF Metadata provided by EXIF.tools