Reo link Digital Technology REOLINKGO IP Camera User Manual Reolink go QSG2 A 20180829

Shenzhen Reo-link Digital Technology Co., Ltd IP Camera Reolink go QSG2 A 20180829

user_manual

・  RMA ContactVisit https://support.reolink.comSubmit a Request withyour Order No.Reolink After Servicewill contact with youfor processingOrderRMA・  Technical SupportSubmit a RequestTechnicalsupportTroubleshooting your problemVisit https://support.reolink.comQSG2_AReolink GoQuick Start GuideTest Model：Reolink GO
Skinx1RechargeableBatteryx1Reset NeedlePack of Screwsx1Surveillance Signx1Micro USBCablex1Reolink gox1Outdoor SecurityMountx1Quick Start Guidex1MountingHole Templatex1**The camera and the rechargeable battery are packed separately in the same package.*Please dress the camera with the skin for better weatherproof performance whenyou install the camera outdoors.*What’s in the BoxContentsEnglish 11English
General IntroductionBuilt-in MicLensStatus LEDDaylight SensorBult-in PIR SensorMicro USB PortBattery Status LEDSpeakerSIM Card SlotMicro SD Card SlotReset HoleInstall the SIM Card and Battery1. Rotate the back cover counterclockwise, insert the SIM card into the slot.2. Insert the battery into the camera and tighten the back cover.• Tips for SIM CardMicro-SIM /3FF(2004)•Tips for SIM CarMicro-SIM /3FF(2004)0.59in/15mm0.47in/12mmSize of the micro SIM card required is as below• The SIM card supports WCDMA and FDD LTE.ɍ±ŲŤĞ±UtĐóƙėơľóǍĞó¦UvĐŲėĞɏƖśĞóơĞȊƙơƭśǔƵơĞǔŲƵƙơŤóƙƭƖľŲŦĞƭŲdisable the PIN.• Activate the card through your smartphone or your operator before inserting it into the camera.Note: Please make sure the SIM card can work in your smartphone.3English2 English
Register Online (Camera Initial Setup)1. After the SIM card and battery are installed, a red light will be on, and you will hear the voice prompt"Camera is starting up, please wait". The red LED will be solid on for some seconds and ķŲŲȅɔȑɔďśƵĞj1(ǎŃśśȋóơľĶŲƙơŲŤĞơĞĐŲŦėơóŦėthen go solid before going out, you would hear"Network connection succeeded”, which means the camera has been successfully connected to the network. Voice Prompt LED Status Camera Status Solution3421Red LED is solid on for some seconds and then start to ȋóơľYour SIM card has a PINCamera fails to be registered to the operator networkCamera fails to connect to the Reolink serverDevice will go into Standby mode and try to reconnect laterBlue LED will not go solid and just ķŲŲȅRed LED is solid on for some time and ƭľĞŦķŲŲȅcompletelyNote: You may also run into the below situations:1.Check whether you made a reverse direction of SIM card2.Check if the SIM card is not fully inserted, please insert it again1.Check whether your card is activated or not, if not please call your operator to activate it2.Your current location may have a weak signal, please move the camera to a location with better signal"SIM card cannot be recognized!"" The SIM card is locked with a PIN. Please disable it""Network connection failed"Camera cannot recognize this SIM cardPut the SIM card into your mobile phone and disable the PIN4 English 5English
1. Please click the “ ” button in the top right corner to add the camera. 2. Scan the QR code on the side of the camera and follow the steps to complete the setup.3. After you created a password for your camera, please follow the steps to sync the time, and then start live view or go to “Device Settings” Battery StatusAdd New DeviceMenuEnable/Disable PIR Motion Sensor(In default, the PIR sensor is enabled.)Device SettingsAccess the Live ViewDownload and install the Reolink App in App Store (for iOS) and Google Play (for Android).Available on the Get it onSetup Camera on Reolink App (For Smartphone)6 English 7English
Attention for Camera Installation• PIR Sensor Detecting DistanceThe PIR senor has 3 sensitivity levels for your adjustment: Low/Mid/High. PŃķľĞƙơĞŦơŃƭŃǍŃƭǔŲȅĞƙơśŲŦķĞƙėĞƭĞĐƭŃŦķėŃơƭóŦĐĞɔ¾ľĞėĞĶóƵśƭơĞŦơŃƭŃǍŃƭǔŲĶƭľĞ¦U©ơĞŦơŲƙŃơóƭɽtŃėɾɔPath for adjusting distance in App: Device settings-PIR settingsNote: Sensitivity Detecting Distance(For moving vehicles)HighMidLowUp to 9 meters (30ft)Up to 6 meters (20ft)Up to 4 meters (13ft)Value81 - 10051 - 800 - 50To reduce false alarms, please note that:• Do not install the camera facing any objects with bright lights, including sunshine, bright lamp lights, etc.• Do not place the camera too close to a place where there are frequently moving vehicles. Based on our numerous tests, the recommended distance between the camera and the vehicle is 16 meters (52ft).ɍ±ƭóǔóǎóǔĶƙŲŤƭľĞŲƵƭśĞƭơɏŃŦĐśƵėŃŦķƭľĞóŃƙĐŲŦėŃƭŃŲŦĞƙǍĞŦƭơɏľƵŤŃėŃȊĞƙŲƵƭśĞƭơɏƭľĞheat transfer vents of projectors, etc.• Do not install the camera where there are strong winds.• Do not install the camera facing the mirror.• Keep the camera at least 1 meter away from any wireless devices, including Wi-Fi routers and phones in order to avoid wireless interference.!Important Notes for ReducingFalse AlarmsUp to 10 meters (33ft)Up to 12 meters (40ft)Up to 16 meters (52ft)Detecting Distance(For moving and living things)8 English 9English
!Charge the BatteryCharging indicator: Green LED: Fully chargedPlease learn some useful ways to maximize the battery life in this post:https://reolink.com/faq/extend-battery-life/Ɋ ¦śĞóơĞŦŲƭĞƭľóƭƭľĞơŲśóƙƖóŦĞśŃơv¾ŃŦĐśƵėĞėŃŦƭľĞƖóĐŘóķĞɔäŲƵĐóŦďƵǔƭľĞơŲśóƙƖóŦĞśŲŦ©ĞŲśŃŦŘŲȆĐŃóśŲŦśŃŦĞstore. Reolink Go is not designed for 24/7 full capacity running or around-the-clock live streaming. It’s designed to record motion events and remotely view live streaming only when you need it.Important Safeguards on Rechargeable Battery Use1. Charge the battery when it's installed to the camera. 2. Charge the battery separately. 3. Charge the battery with the Reolink solar panel. Orange LED: Charging When installing the camera, please install the camera angularly (the angle between the sensor and the detected ŲďŕĞĐƭŃơśóƙķĞƙƭľóŦȐȏˆɧĶŲƙĞȅĞĐƭŃǍĞŤŲƭŃŲŦėĞƭĞĐƭŃŲŦɔUĶthe moving object approaches the PIR sensor vertically, the sensor may not detect the motion events.The ideal viewing distance is 2-10 meters (7-33ft), which enables you to recognize a human.EntranceÁThe path of themoving objectFYI: • The PIR sensor’s detecting distance: 23ft (in default)• The PIR sensor’s detecting angle: 120° (H)• Camera Ideal ViewingDistance• PIR Sensor Installation Angle10°Á2-3 metersIdeal Viewing Distance:2-10 meters (7-33ft)10 English 11English
1. Please charge the rechargeable battery with a standard and high-quality DC 5V or 9V battery charger.2. If you want to power the battery via the solar panel, please note that the battery is ONLY compatible with Reolink solar panel. You cannot charge the battery with other solar panel brands.3. Please charge the battery in temperatures between 0°C and 45°C.4. Always use the battery in temperatures between -20°C and 60°C.5. Please make sure the battery compartment is clean.6. Please keep the USB charging port dry, clean and free of any debris and make sure the battery contacts are aligned.7. Always make sure the USB charging port is clean. Please cover the USB charging port with the rubber plug after the battery has been fully charged.ȗɔvĞǍĞƙĐľóƙķĞɏƵơĞŲƙơƭŲƙĞƭľĞďóƭƭĞƙǔŦĞóƙóŦǔŃķŦŃƭŃŲŦơŲƵƙĐĞơɏơƵĐľóơȊƙĞŲƙľĞóƭĞƙơɔ9. Always store the battery in a cool, dry and ventilated environment.10. Never store the battery with any hazardous or combustible objects.11. Do keep the battery away from children.12. Do not short-circuit the battery by connecting wires or other metal objects to the positive (+) and negative (-) terminals. Do NOT transport or store the battery with necklaces, hairpins or other metal objects.ȐȒɔ(Ųv¾ėŃơóơơĞŤďśĞɏĐƵƭɏƖƵŦĐƭƵƙĞɏơľŲƙƭɲĐŃƙĐƵŃƭƭľĞďóƭƭĞƙǔɏŲƙŤóŘĞŃƭėŃơƖŲơĞŲĶŃŦǎóƭĞƙɏȊƙĞɏmicrowave ovens and pressure vessels.Ȑȓɔ(Ųv¾ƵơĞƭľĞďóƭƭĞƙǔŃĶŃƭķŃǍĞơŲȅóŦŲėŲƙɏķĞŦĞƙóƭĞơľĞóƭɏďĞĐŲŤĞơėŃơĐŲśŲƙĞėŲƙėĞĶŲƙŤĞėɏŲƙappears abnormal in any ways. If the battery is being used or charged, remove the battery from the device or the charger immediately, and stop using it.15. Always follow the local waste and recycle laws when throwing the used battery away.How to Install Wall MountUse the allen wrench to loose the screw.Step 1Screw the wall mount into the wall.Step 2Screw the camera to the wall mount and adjust the camera to the proper direction.Step 3Tighten the screw using the allen wrench.Step 412 English 13English
20C

Navigation menu